diff options
Diffstat (limited to 'include/configs/p3p440.h')
| -rwxr-xr-x | include/configs/p3p440.h | 318 |
1 files changed, 318 insertions, 0 deletions
diff --git a/include/configs/p3p440.h b/include/configs/p3p440.h new file mode 100755 index 0000000..831d018 --- /dev/null +++ b/include/configs/p3p440.h @@ -0,0 +1,318 @@ +/* + * (C) Copyright 2005 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/************************************************************************ + * board/config_p3p440.h - configuration for Prodrive P3P440 + ***********************************************************************/ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/*----------------------------------------------------------------------- + * High Level Configuration Options + *----------------------------------------------------------------------*/ +#define CONFIG_P3P440 1 /* Board is P3P440 */ +#define CONFIG_440GP 1 /* Specifc GP support */ +#define CONFIG_4xx 1 /* ... PPC4xx family */ +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ +#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ + +/*----------------------------------------------------------------------- + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + *----------------------------------------------------------------------*/ +#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CFG_FLASH_BASE 0xff800000 /* start of FLASH */ +#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */ +#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ +#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ +#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */ +#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */ + +#define CFG_USB_BASE (CFG_PERIPHERAL_BASE + 0x00000000) + +/*----------------------------------------------------------------------- + * Initial RAM & stack pointer (placed in internal SRAM) + *----------------------------------------------------------------------*/ +#define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */ +#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ + +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon*/ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/ + +/*----------------------------------------------------------------------- + * DDR SDRAM + *----------------------------------------------------------------------*/ +#define CONFIG_SDRAM_BANK0 1 /* init onboard DDR SDRAM bank 0*/ +#define CFG_SDRAM_TABLE { \ + {(256 << 20), 0x000C4001}, /* 256MB mode 3, 13x10(4) */ \ + {(64 << 20), 0x00082001}} /* 64MB mode 2, 12x9(4) */ + +/*----------------------------------------------------------------------- + * Serial Port + *----------------------------------------------------------------------*/ +#undef CFG_EXT_SERIAL_CLOCK +#define CONFIG_BAUDRATE 115200 + +#define CFG_BAUDRATE_TABLE \ + { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ + 57600, 115200, 230400, 460800, 921600 } + +/*----------------------------------------------------------------------- + * I2C + *----------------------------------------------------------------------*/ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ + +/*----------------------------------------------------------------------- + * I2C RTC + *----------------------------------------------------------------------*/ +#define CONFIG_RTC_MAX6900 1 /* MAX6900 RTC */ + +/*----------------------------------------------------------------------- + * I2C EEPROM (PCF8594C) for environment + *----------------------------------------------------------------------*/ +#define CFG_I2C_EEPROM_ADDR 0x54 /* EEPROM PCF8594C */ +#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ +/* mask of address bits that overflow into the "EEPROM chip address" */ +#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07 +#define CFG_EEPROM_PAGE_WRITE_BITS 3 /* The Philips PCF8594C has */ + /* 8 byte page write mode using */ + /* last 3 bits of the address */ +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 40 /* and takes up to 40 msec */ +#define CFG_EEPROM_PAGE_WRITE_ENABLE + +/*----------------------------------------------------------------------- + * Default configuration (environment varibles...) + *----------------------------------------------------------------------*/ +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "hostname=p3p440\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ + "bootm\0" \ + "rootpath=/opt/eldk/ppc_4xx\0" \ + "bootfile=/tftpboot/p3p440/uImage\0" \ + "kernel_addr=ff800000\0" \ + "ramdisk_addr=ff810000\0" \ + "load=tftp 100000 /tftpboot/p3p440/u-boot.bin\0" \ + "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ + "cp.b 100000 fffc0000 40000;" \ + "setenv filesize;saveenv\0" \ + "upd=run load;run update\0" \ + "" +#define CONFIG_BOOTCOMMAND "run net_nfs" + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 0x1c /* PHY address */ +#define CONFIG_HAS_ETH1 +#define CONFIG_PHY1_ADDR 0x1d /* EMAC1 PHY address */ +#define CONFIG_NET_MULTI 1 +#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ + +#define CONFIG_NETCONSOLE /* include NetConsole support */ + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_ASKENV | \ + CFG_CMD_DATE | \ + CFG_CMD_DHCP | \ + CFG_CMD_DIAG | \ + CFG_CMD_ELF | \ + CFG_CMD_I2C | \ + CFG_CMD_IRQ | \ + CFG_CMD_MII | \ + CFG_CMD_NET | \ + CFG_CMD_NFS | \ + CFG_CMD_PCI | \ + CFG_CMD_PING | \ + CFG_CMD_REGINFO | \ + CFG_CMD_EEPROM | \ + CFG_CMD_SNTP ) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/*----------------------------------------------------------------------- + * Miscellaneous configurable options + *----------------------------------------------------------------------*/ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ +#define CONFIG_LOOPW 1 /* enable loopw command */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------*/ +/* General PCI */ +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */ + +/* Board-specific PCI */ +#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */ +#define CFG_PCI_TARGET_INIT /* let board init pci target */ + +#define CONFIG_DISABLE_PISE_TEST /* disable PISE test (PCIX only)*/ + +#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ +#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ + +/*----------------------------------------------------------------------- + * External Bus Controller (EBC) Setup + *----------------------------------------------------------------------*/ +#define CFG_FLASH0 0xFF800000 +#define CFG_FLASH1 0xFF000000 +#define CFG_FLASH2 0xFE800000 +#define CFG_FLASH3 0xFE000000 +#define CFG_USB 0xF0000000 + +/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */ +#define CFG_EBC_PB0AP 0x03050200 +#define CFG_EBC_PB0CR (CFG_FLASH0 | 0x7A000) /* BAS=0xFF8,BS=8MB,BU=R/W,BW=16bit */ + +/* Memory Bank 1 (Flash Bank 1, NOR-FLASH) initialization */ +#define CFG_EBC_PB1AP 0x03050200 +#define CFG_EBC_PB1CR (CFG_FLASH1 | 0x7A000) /* BAS=0xFF8,BS=8MB,BU=R/W,BW=16bit */ + +/* Memory Bank 2 (Flash Bank 2, NOR-FLASH) initialization */ +#define CFG_EBC_PB2AP 0x03050200 +#define CFG_EBC_PB2CR (CFG_FLASH2 | 0x7A000) /* BAS=0xFF8,BS=8MB,BU=R/W,BW=16bit */ + +/* Memory Bank 3 (Flash Bank 3, NOR-FLASH) initialization */ +#define CFG_EBC_PB3AP 0x03050200 +#define CFG_EBC_PB3CR (CFG_FLASH3 | 0x7A000) /* BAS=0xFF8,BS=8MB,BU=R/W,BW=16bit */ + +/* Memory Bank 7 (USB controller) initialization */ +#define CFG_EBC_PB7AP 0x02015000 +#define CFG_EBC_PB7CR (CFG_USB | 0xFE000) /* BAS=0xF00,BS=128MB,BU=R/W,BW=16bit*/ + +/*----------------------------------------------------------------------- + * FLASH related + *----------------------------------------------------------------------*/ +#define CFG_FLASH_CFI /* The flash is CFI compatible */ +#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ + +#define CFG_FLASH_BANKS_LIST { CFG_FLASH3, CFG_FLASH2, CFG_FLASH1, CFG_FLASH0 } + +#define CFG_MAX_FLASH_BANKS 4 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ + +#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ + +#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ +#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 405 CPUs */ +#define CFG_CACHELINE_SIZE 32 /* ... */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif +#endif /* __CONFIG_H */ |