diff options
Diffstat (limited to '2.3-1/includes/bcm2835.h')
| -rw-r--r-- | 2.3-1/includes/bcm2835.h | 1625 |
1 files changed, 1625 insertions, 0 deletions
diff --git a/2.3-1/includes/bcm2835.h b/2.3-1/includes/bcm2835.h new file mode 100644 index 00000000..ae41b3e1 --- /dev/null +++ b/2.3-1/includes/bcm2835.h @@ -0,0 +1,1625 @@ +/* bcm2835.h + + C and C++ support for Broadcom BCM 2835 as used in Raspberry Pi + + Author: Mike McCauley + Copyright (C) 2011-2013 Mike McCauley + $Id: bcm2835.h,v 1.20 2015/03/31 04:55:41 mikem Exp mikem $ +*/ + +/*! \mainpage C library for Broadcom BCM 2835 as used in Raspberry Pi + + This is a C library for Raspberry Pi (RPi). It provides access to + GPIO and other IO functions on the Broadcom BCM 2835 chip, + allowing access to the GPIO pins on the + 26 pin IDE plug on the RPi board so you can control and interface with various external devices. + + It provides functions for reading digital inputs and setting digital outputs, using SPI and I2C, + and for accessing the system timers. + Pin event detection is supported by polling (interrupts are not supported). + + It is C++ compatible, and installs as a header file and non-shared library on + any Linux-based distro (but clearly is no use except on Raspberry Pi or another board with + BCM 2835). + + The version of the package that this documentation refers to can be downloaded + from http://www.airspayce.com/mikem/bcm2835/bcm2835-1.48.tar.gz + You can find the latest version at http://www.airspayce.com/mikem/bcm2835 + + Several example programs are provided. + + Based on data in http://elinux.org/RPi_Low-level_peripherals and + http://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf + and http://www.scribd.com/doc/101830961/GPIO-Pads-Control2 + + You can also find online help and discussion at http://groups.google.com/group/bcm2835 + Please use that group for all questions and discussions on this topic. + Do not contact the author directly, unless it is to discuss commercial licensing. + Before asking a question or reporting a bug, please read http://www.catb.org/esr/faqs/smart-questions.html + + Tested on debian6-19-04-2012, 2012-07-15-wheezy-raspbian, 2013-07-26-wheezy-raspbian + and Occidentalisv01 + CAUTION: it has been observed that when detect enables such as bcm2835_gpio_len() + are used and the pin is pulled LOW + it can cause temporary hangs on 2012-07-15-wheezy-raspbian, 2013-07-26-wheezy-raspbian + and Occidentalisv01. + Reason for this is not yet determined, but we suspect that an interrupt handler is + hitting a hard loop on those OSs. + If you must use bcm2835_gpio_len() and friends, make sure you disable the pins with + bcm2835_gpio_clr_len() and friends after use. + + \par Installation + + This library consists of a single non-shared library and header file, which will be + installed in the usual places by make install + + \code + # download the latest version of the library, say bcm2835-1.xx.tar.gz, then: + tar zxvf bcm2835-1.xx.tar.gz + cd bcm2835-1.xx + ./configure + make + sudo make check + sudo make install + \endcode + + \par Physical Addresses + + The functions bcm2835_peri_read(), bcm2835_peri_write() and bcm2835_peri_set_bits() + are low level peripheral register access functions. They are designed to use + physical addresses as described in section 1.2.3 ARM physical addresses + of the BCM2835 ARM Peripherals manual. + Physical addresses range from 0x20000000 to 0x20FFFFFF for peripherals. The bus + addresses for peripherals are set up to map onto the peripheral bus address range starting at + 0x7E000000. Thus a peripheral advertised in the manual at bus address 0x7Ennnnnn is available at + physical address 0x20nnnnnn. + + On RPI 2, the peripheral addresses are different and the bcm2835 library gets them + from reading /proc/device-tree/soc/ranges. This is only availble with recent versions of the kernel on RPI 2. + + After initialisation, the base address of the various peripheral + registers are available with the following + externals: + bcm2835_gpio + bcm2835_pwm + bcm2835_clk + bcm2835_pads + bcm2835_spio0 + bcm2835_st + bcm2835_bsc0 + bcm2835_bsc1 + + \par Raspberry Pi 2 (RPI2) + + For this library to work correctly on RPI2, you MUST have the device tree support enabled in the kernel. + You should also ensure you are using the latest version of Linux. The library has been tested on RPI2 + with 2015-02-16-raspbian-wheezy and ArchLinuxARM-rpi-2 as of 2015-03-29. + + When device tree suport is enabled, the file /proc/device-tree/soc/ranges will appear in the file system, + and the bcm2835 module relies on its presence to correctly run on RPI2 (it is optional for RPI1). + Without device tree support enabled and the presence of this file, it will not work on RPI2. + + To enable device tree support: + + \code + sudo raspi-config + under Advanced Options - enable Device Tree + Reboot. + \endcode + + \par Pin Numbering + + The GPIO pin numbering as used by RPi is different to and inconsistent with the underlying + BCM 2835 chip pin numbering. http://elinux.org/RPi_BCM2835_GPIOs + + RPi has a 26 pin IDE header that provides access to some of the GPIO pins on the BCM 2835, + as well as power and ground pins. Not all GPIO pins on the BCM 2835 are available on the + IDE header. + + RPi Version 2 also has a P5 connector with 4 GPIO pins, 5V, 3.3V and Gnd. + + The functions in this library are designed to be passed the BCM 2835 GPIO pin number and _not_ + the RPi pin number. There are symbolic definitions for each of the available pins + that you should use for convenience. See \ref RPiGPIOPin. + + \par SPI Pins + + The bcm2835_spi_* functions allow you to control the BCM 2835 SPI0 interface, + allowing you to send and received data by SPI (Serial Peripheral Interface). + For more information about SPI, see http://en.wikipedia.org/wiki/Serial_Peripheral_Interface_Bus + + When bcm2835_spi_begin() is called it changes the bahaviour of the SPI interface pins from their + default GPIO behaviour in order to support SPI. While SPI is in use, you will not be able + to control the state of the SPI pins through the usual bcm2835_spi_gpio_write(). + When bcm2835_spi_end() is called, the SPI pins will all revert to inputs, and can then be + configured and controled with the usual bcm2835_gpio_* calls. + + The Raspberry Pi GPIO pins used for SPI are: + + - P1-19 (MOSI) + - P1-21 (MISO) + - P1-23 (CLK) + - P1-24 (CE0) + - P1-26 (CE1) + + \par I2C Pins + + The bcm2835_i2c_* functions allow you to control the BCM 2835 BSC interface, + allowing you to send and received data by I2C ("eye-squared cee"; generically referred to as "two-wire interface") . + For more information about I?C, see http://en.wikipedia.org/wiki/I%C2%B2C + + The Raspberry Pi V2 GPIO pins used for I2C are: + + - P1-03 (SDA) + - P1-05 (SLC) + + \par PWM + + The BCM2835 supports hardware PWM on a limited subset of GPIO pins. This bcm2835 library provides + functions for configuring and controlling PWM output on these pins. + + The BCM2835 contains 2 independent PWM channels (0 and 1), each of which be connnected to a limited subset of + GPIO pins. The following GPIO pins may be connected to the following PWM channels (from section 9.5): + \code + GPIO PIN RPi pin PWM Channel ALT FUN + 12 0 0 + 13 1 0 + 18 1-12 0 5 + 19 1 5 + 40 0 0 + 41 1 0 + 45 1 0 + 52 0 1 + 53 1 1 + \endcode + In order for a GPIO pin to emit output from its PWM channel, it must be set to the Alt Function given above. + Note carefully that current versions of the Raspberry Pi only expose one of these pins (GPIO 18 = RPi Pin 1-12) + on the IO headers, and therefore this is the only IO pin on the RPi that can be used for PWM. + Further it must be set to ALT FUN 5 to get PWM output. + + Both PWM channels are driven by the same PWM clock, whose clock dvider can be varied using + bcm2835_pwm_set_clock(). Each channel can be separately enabled with bcm2835_pwm_set_mode(). + The average output of the PWM channel is determined by the ratio of DATA/RANGE for that channel. + Use bcm2835_pwm_set_range() to set the range and bcm2835_pwm_set_data() to set the data in that ratio + + Each PWM channel can run in either Balanced or Mark-Space mode. In Balanced mode, the hardware + sends a combination of clock pulses that results in an overall DATA pulses per RANGE pulses. + In Mark-Space mode, the hardware sets the output HIGH for DATA clock pulses wide, followed by + LOW for RANGE-DATA clock pulses. + + The PWM clock can be set to control the PWM pulse widths. The PWM clock is derived from + a 19.2MHz clock. You can set any divider, but some common ones are provided by the BCM2835_PWM_CLOCK_DIVIDER_* + values of \ref bcm2835PWMClockDivider. + + For example, say you wanted to drive a DC motor with PWM at about 1kHz, + and control the speed in 1/1024 increments from + 0/1024 (stopped) through to 1024/1024 (full on). In that case you might set the + clock divider to be 16, and the RANGE to 1024. The pulse repetition frequency will be + 1.2MHz/1024 = 1171.875Hz. + + \par SPI + + In order for bcm2835 library SPI to work, you may need to disable the SPI kernel module using: + + \code + sudo raspi-config + under Advanced Options - enable Device Tree + under Advanced Options - disable SPI + Reboot. + \endcode + + \par Real Time performance constraints + + The bcm2835 is a library for user programs (i.e. they run in 'userland'). + Such programs are not part of the kernel and are usually + subject to paging and swapping by the kernel while it does other things besides running your program. + This means that you should not expect to get real-time performance or + real-time timing constraints from such programs. In particular, there is no guarantee that the + bcm2835_delay() and bcm2835_delayMicroseconds() will return after exactly the time requested. + In fact, depending on other activity on the host, IO etc, you might get significantly longer delay times + than the one you asked for. So please dont expect to get exactly the time delay you request. + + Arjan reports that you can prevent swapping on Linux with the following code fragment: + + \code + struct sched_param sp; + memset(&sp, 0, sizeof(sp)); + sp.sched_priority = sched_get_priority_max(SCHED_FIFO); + sched_setscheduler(0, SCHED_FIFO, &sp); + mlockall(MCL_CURRENT | MCL_FUTURE); + \endcode + + \par Bindings to other languages + + mikem has made Perl bindings available at CPAN: + http://search.cpan.org/~mikem/Device-BCM2835-1.9/lib/Device/BCM2835.pm + Matthew Baker has kindly made Python bindings available at: + https: github.com/mubeta06/py-libbcm2835 + Gary Marks has created a Serial Peripheral Interface (SPI) command-line utility + for Raspberry Pi, based on the bcm2835 library. The + utility, spincl, is licensed under Open Source GNU GPLv3 by iP Solutions (http://ipsolutionscorp.com), as a + free download with source included: http://ipsolutionscorp.com/raspberry-pi-spi-utility/ + + \par Open Source Licensing GPL V2 + + This is the appropriate option if you want to share the source code of your + application with everyone you distribute it to, and you also want to give them + the right to share who uses it. If you wish to use this software under Open + Source Licensing, you must contribute all your source code to the open source + community in accordance with the GPL Version 2 when your application is + distributed. See http://www.gnu.org/copyleft/gpl.html and COPYING + + \par Acknowledgements + + Some of this code has been inspired by Dom and Gert. + The I2C code has been inspired by Alan Barr. + + \par Revision History + + \version 1.0 Initial release + + \version 1.1 Minor bug fixes + + \version 1.2 Added support for SPI + + \version 1.3 Added bcm2835_spi_transfern() + + \version 1.4 Fixed a problem that prevented SPI CE1 being used. Reported by David Robinson. + + \version 1.5 Added bcm2835_close() to deinit the library. Suggested by C?sar Ortiz + + \version 1.6 Document testing on 2012-07-15-wheezy-raspbian and Occidentalisv01 + Functions bcm2835_gpio_ren(), bcm2835_gpio_fen(), bcm2835_gpio_hen() + bcm2835_gpio_len(), bcm2835_gpio_aren() and bcm2835_gpio_afen() now + changes only the pin specified. Other pins that were already previously + enabled stay enabled. + Added bcm2835_gpio_clr_ren(), bcm2835_gpio_clr_fen(), bcm2835_gpio_clr_hen() + bcm2835_gpio_clr_len(), bcm2835_gpio_clr_aren(), bcm2835_gpio_clr_afen() + to clear the enable for individual pins, suggested by Andreas Sundstrom. + + \version 1.7 Added bcm2835_spi_transfernb to support different buffers for read and write. + + \version 1.8 Improvements to read barrier, as suggested by maddin. + + \version 1.9 Improvements contributed by mikew: + I noticed that it was mallocing memory for the mmaps on /dev/mem. + It's not necessary to do that, you can just mmap the file directly, + so I've removed the mallocs (and frees). + I've also modified delayMicroseconds() to use nanosleep() for long waits, + and a busy wait on a high resolution timer for the rest. This is because + I've found that calling nanosleep() takes at least 100-200 us. + You need to link using '-lrt' using this version. + I've added some unsigned casts to the debug prints to silence compiler + warnings I was getting, fixed some typos, and changed the value of + BCM2835_PAD_HYSTERESIS_ENABLED to 0x08 as per Gert van Loo's doc at + http://www.scribd.com/doc/101830961/GPIO-Pads-Control2 + Also added a define for the passwrd value that Gert says is needed to + change pad control settings. + + \version 1.10 Changed the names of the delay functions to bcm2835_delay() + and bcm2835_delayMicroseconds() to prevent collisions with wiringPi. + Macros to map delay()-> bcm2835_delay() and + Macros to map delayMicroseconds()-> bcm2835_delayMicroseconds(), which + can be disabled by defining BCM2835_NO_DELAY_COMPATIBILITY + + \version 1.11 Fixed incorrect link to download file + + \version 1.12 New GPIO pin definitions for RPi version 2 (which has a different GPIO mapping) + + \version 1.13 New GPIO pin definitions for RPi version 2 plug P5 + Hardware base pointers are now available (after initialisation) externally as bcm2835_gpio + bcm2835_pwm bcm2835_clk bcm2835_pads bcm2835_spi0. + + \version 1.14 Now compiles even if CLOCK_MONOTONIC_RAW is not available, uses CLOCK_MONOTONIC instead. + Fixed errors in documentation of SPI divider frequencies based on 250MHz clock. + Reported by Ben Simpson. + + \version 1.15 Added bcm2835_close() to end of examples as suggested by Mark Wolfe. + + \version 1.16 Added bcm2835_gpio_set_multi, bcm2835_gpio_clr_multi and bcm2835_gpio_write_multi + to allow a mask of pins to be set all at once. Requested by Sebastian Loncar. + + \version 1.17 Added bcm2835_gpio_write_mask. Requested by Sebastian Loncar. + + \version 1.18 Added bcm2835_i2c_* functions. Changes to bcm2835_delayMicroseconds: + now uses the RPi system timer counter, instead of clock_gettime, for improved accuracy. + No need to link with -lrt now. Contributed by Arjan van Vught. + \version 1.19 Removed inlines added by previous patch since they don't seem to work everywhere. + Reported by olly. + + \version 1.20 Patch from Mark Dootson to close /dev/mem after access to the peripherals has been granted. + + \version 1.21 delayMicroseconds is now not susceptible to 32 bit timer overruns. + Patch courtesy Jeremy Mortis. + + \version 1.22 Fixed incorrect definition of BCM2835_GPFEN0 which broke the ability to set + falling edge events. Reported by Mark Dootson. + + \version 1.23 Added bcm2835_i2c_set_baudrate and bcm2835_i2c_read_register_rs. + Improvements to bcm2835_i2c_read and bcm2835_i2c_write functions + to fix ocasional reads not completing. Patched by Mark Dootson. + + \version 1.24 Mark Dootson p[atched a problem with his previously submitted code + under high load from other processes. + + \version 1.25 Updated author and distribution location details to airspayce.com + + \version 1.26 Added missing unmapmem for pads in bcm2835_close to prevent a memory leak. + Reported by Hartmut Henkel. + + \version 1.27 bcm2835_gpio_set_pad() no longer needs BCM2835_PAD_PASSWRD: it is + now automatically included. + Added suport for PWM mode with bcm2835_pwm_* functions. + + \version 1.28 Fixed a problem where bcm2835_spi_writenb() would have problems with transfers of more than + 64 bytes dues to read buffer filling. Patched by Peter Würtz. + + \version 1.29 Further fix to SPI from Peter Würtz. + + \version 1.30 10 microsecond delays from bcm2835_spi_transfer and bcm2835_spi_transfern for + significant performance improvements, Patch by Alan Watson. + + \version 1.31 Fix a GCC warning about dummy variable, patched by Alan Watson. Thanks. + + \version 1.32 Added option I2C_V1 definition to compile for version 1 RPi. + By default I2C code is generated for the V2 RPi which has SDA1 and SCL1 connected. + Contributed by Malcolm Wiles based on work by Arvi Govindaraj. + + \version 1.33 Added command line utilities i2c and gpio to examples. Contributed by Shahrooz Shahparnia. + + \version 1.34 Added bcm2835_i2c_write_read_rs() which writes an arbitrary number of bytes, + sends a repeat start, and reads from the device. Contributed by Eduardo Steinhorst. + + \version 1.35 Fix build errors when compiled under Qt. Also performance improvements with SPI transfers. Contributed b Udo Klaas. + + \version 1.36 Make automake's test runner detect that we're skipping tests when not root, the second + one makes us skip the test when using fakeroot (as used when building + Debian packages). Contributed by Guido Günther. + + \version 1.37 Moved confiure.in to configure.ac as receommnded by autoreconf.<br> + Improvements to bcm2835_st_read to account for possible timer overflow, contributed by 'Ed'.<br> + Added definitions for Raspberry Pi B+ J8 header GPIO pins.<br> + + \version 1.38 Added bcm2835_regbase for the benefit of C# wrappers, patch by Frank Hommers <br> + + \version 1.39 Beta version of RPi2 compatibility. Not tested here on RPi2 hardware. + Testers please confirm correct operation on RPi2.<br> + Unneccessary 'volatile' qualifiers removed from all variables and signatures.<br> + Removed unsupportable PWM dividers, based on a report from Christophe Cecillon.<br> + Minor improvements to spi.c example.<br> + + \version 1.40 Correct operation on RPi2 has been confirmed.<br> + Fixed a number of compiler errors and warnings that occur when bcm2835.h is included + in code compiled with -Wall -Woverflow -Wstrict-overflow -Wshadow -Wextra -pedantic. + Reported by tlhackque.<br> + Fixed a problem where calling bcm2835_delayMicroseconds loops forever when debug is set. Reported by tlhackque.<br> + Reinstated use of volatile in 2 functions where there was a danger of lost reads or writes. Reported by tlhackque.<br> + + \version 1.41 Added BCM2835_VERSION macro and new function bcm2835_version(); Requested by tlhackque.<br> + Improvements to peripheral memory barriers as suggested by tlhackque.<br> + Reinstated some necessary volatile declarations as requested by tlhackque.<br> + + \version 1.42 Further improvements to memory barriers with the patient assistance and patches of tlhackque.<br> + + \version 1.43 Fixed problems with compiling barriers on RPI 2 with Arch Linux and gcc 4.9.2. + Reported and patched by Lars Christensen.<br> + Testing on RPI 2, with ArchLinuxARM-rpi-2-latest and 2015-02-16-raspbian-wheezy.<br> + + \version 1.44 Added documention about the need for device tree to be enabled on RPI2.<br> + Improvements to detection of availablity of DMB instruction based on value of __ARM_ARCH macro.<br> + + \version 1.45 Fixed an error in the pad group offsets that would prevent bcm2835_gpio_set_pad() + and bcm2835_gpio_pad() working correctly with non-0 pad groups. Reported by Guido. + + \version 1.46 2015-09-18 + Added symbolic definitions for remaining pins on 40 pin GPIO header on RPi 2. <br> + + \version 1.47 2015-11-18 + Fixed possibly incorrect reads in bcm2835_i2c_read_register_rs, patch from Eckhardt Ulrich.<br> + + \version 1.48 2015-12-08 + Added patch from Eckhardt Ulrich that fixed problems that could cause hanging with bcm2835_i2c_read_register_rs + and others. + + \author Mike McCauley (mikem@airspayce.com) DO NOT CONTACT THE AUTHOR DIRECTLY: USE THE LISTS +*/ + + +/* Defines for BCM2835 */ +#ifndef BCM2835_H +#define BCM2835_H + +#include <stdint.h> + +#define BCM2835_VERSION 10048 /* Version 1.48 */ + +/* RPi 2 is ARM v7, and has DMB instruction for memory barriers. + Older RPis are ARM v6 and don't, so a coprocessor instruction must be used instead. + However, not all versions of gcc in all distros support the dmb assembler instruction even on conmpatible processors. + This test is so any ARMv7 or higher processors with suitable GCC will use DMB. +*/ +#if __ARM_ARCH >= 7 +#define BCM2835_HAVE_DMB +#endif + +/*! \defgroup constants Constants for passing to and from library functions + The values here are designed to be passed to various functions in the bcm2835 library. + @{ +*/ + +/*! This means pin HIGH, true, 3.3volts on a pin. */ +#define HIGH 0x1 +/*! This means pin LOW, false, 0volts on a pin. */ +#define LOW 0x0 + +/*! Speed of the core clock core_clk */ +#define BCM2835_CORE_CLK_HZ 250000000 /*!< 250 MHz */ + +/*! On RPi2 with BCM2836, and all recent OSs, the base of the peripherals is read from a /proc file */ +#define BMC2835_RPI2_DT_FILENAME "/proc/device-tree/soc/ranges" +/*! Offset into BMC2835_RPI2_DT_FILENAME for the peripherals base address */ +#define BMC2835_RPI2_DT_PERI_BASE_ADDRESS_OFFSET 4 +/*! Offset into BMC2835_RPI2_DT_FILENAME for the peripherals size address */ +#define BMC2835_RPI2_DT_PERI_SIZE_OFFSET 8 + +/*! Physical addresses for various peripheral register sets + Base Physical Address of the BCM 2835 peripheral registers + Note this is different for the RPi2 BCM2836, where this is derived from /proc/device-tree/soc/ranges + If /proc/device-tree/soc/ranges exists on a RPi 1 OS, it would be expected to contain the + following numbers: +*/ +/*! Peripherals block base address on RPi 1 */ +#define BCM2835_PERI_BASE 0x20000000 +/*! Size of the peripherals block on RPi 1 */ +#define BCM2835_PERI_SIZE 0x01000000 + +/*! Offsets for the bases of various peripherals within the peripherals block + / Base Address of the System Timer registers +*/ +#define BCM2835_ST_BASE 0x3000 +/*! Base Address of the Pads registers */ +#define BCM2835_GPIO_PADS 0x100000 +/*! Base Address of the Clock/timer registers */ +#define BCM2835_CLOCK_BASE 0x101000 +/*! Base Address of the GPIO registers */ +#define BCM2835_GPIO_BASE 0x200000 +/*! Base Address of the SPI0 registers */ +#define BCM2835_SPI0_BASE 0x204000 +/*! Base Address of the BSC0 registers */ +#define BCM2835_BSC0_BASE 0x205000 +/*! Base Address of the PWM registers */ +#define BCM2835_GPIO_PWM 0x20C000 +/*! Base Address of the BSC1 registers */ +#define BCM2835_BSC1_BASE 0x804000 + +/*! Physical address and size of the peripherals block + May be overridden on RPi2 +*/ +extern uint32_t *bcm2835_peripherals_base; +/*! Size of the peripherals block to be mapped */ +extern uint32_t bcm2835_peripherals_size; + +/*! Virtual memory address of the mapped peripherals block */ +extern uint32_t *bcm2835_peripherals; + +/*! Base of the ST (System Timer) registers. + Available after bcm2835_init has been called +*/ +extern volatile uint32_t *bcm2835_st; + +/*! Base of the GPIO registers. + Available after bcm2835_init has been called +*/ +extern volatile uint32_t *bcm2835_gpio; + +/*! Base of the PWM registers. + Available after bcm2835_init has been called +*/ +extern volatile uint32_t *bcm2835_pwm; + +/*! Base of the CLK registers. + Available after bcm2835_init has been called +*/ +extern volatile uint32_t *bcm2835_clk; + +/*! Base of the PADS registers. + Available after bcm2835_init has been called +*/ +extern volatile uint32_t *bcm2835_pads; + +/*! Base of the SPI0 registers. + Available after bcm2835_init has been called +*/ +extern volatile uint32_t *bcm2835_spi0; + +/*! Base of the BSC0 registers. + Available after bcm2835_init has been called +*/ +extern volatile uint32_t *bcm2835_bsc0; + +/*! Base of the BSC1 registers. + Available after bcm2835_init has been called +*/ +extern volatile uint32_t *bcm2835_bsc1; + +/*! \brief bcm2835RegisterBase + Register bases for bcm2835_regbase() +*/ +typedef enum +{ + BCM2835_REGBASE_ST = 1, /*!< Base of the ST (System Timer) registers. */ + BCM2835_REGBASE_GPIO = 2, /*!< Base of the GPIO registers. */ + BCM2835_REGBASE_PWM = 3, /*!< Base of the PWM registers. */ + BCM2835_REGBASE_CLK = 4, /*!< Base of the CLK registers. */ + BCM2835_REGBASE_PADS = 5, /*!< Base of the PADS registers. */ + BCM2835_REGBASE_SPI0 = 6, /*! Base of the SPI0 registers. */ + BCM2835_REGBASE_BSC0 = 7, /*!< Base of the BSC0 registers. */ + BCM2835_REGBASE_BSC1 = 8 /*!< Base of the BSC1 registers. */ +} bcm2835RegisterBase; + +/*! Size of memory page on RPi */ +#define BCM2835_PAGE_SIZE (4*1024) +/*! Size of memory block on RPi */ +#define BCM2835_BLOCK_SIZE (4*1024) + + +/* Defines for GPIO + The BCM2835 has 54 GPIO pins. + BCM2835 data sheet, Page 90 onwards. +*/ +/*! GPIO register offsets from BCM2835_GPIO_BASE. + Offsets into the GPIO Peripheral block in bytes per 6.1 Register View +*/ +#define BCM2835_GPFSEL0 0x0000 /*!< GPIO Function Select 0 */ +#define BCM2835_GPFSEL1 0x0004 /*!< GPIO Function Select 1 */ +#define BCM2835_GPFSEL2 0x0008 /*!< GPIO Function Select 2 */ +#define BCM2835_GPFSEL3 0x000c /*!< GPIO Function Select 3 */ +#define BCM2835_GPFSEL4 0x0010 /*!< GPIO Function Select 4 */ +#define BCM2835_GPFSEL5 0x0014 /*!< GPIO Function Select 5 */ +#define BCM2835_GPSET0 0x001c /*!< GPIO Pin Output Set 0 */ +#define BCM2835_GPSET1 0x0020 /*!< GPIO Pin Output Set 1 */ +#define BCM2835_GPCLR0 0x0028 /*!< GPIO Pin Output Clear 0 */ +#define BCM2835_GPCLR1 0x002c /*!< GPIO Pin Output Clear 1 */ +#define BCM2835_GPLEV0 0x0034 /*!< GPIO Pin Level 0 */ +#define BCM2835_GPLEV1 0x0038 /*!< GPIO Pin Level 1 */ +#define BCM2835_GPEDS0 0x0040 /*!< GPIO Pin Event Detect Status 0 */ +#define BCM2835_GPEDS1 0x0044 /*!< GPIO Pin Event Detect Status 1 */ +#define BCM2835_GPREN0 0x004c /*!< GPIO Pin Rising Edge Detect Enable 0 */ +#define BCM2835_GPREN1 0x0050 /*!< GPIO Pin Rising Edge Detect Enable 1 */ +#define BCM2835_GPFEN0 0x0058 /*!< GPIO Pin Falling Edge Detect Enable 0 */ +#define BCM2835_GPFEN1 0x005c /*!< GPIO Pin Falling Edge Detect Enable 1 */ +#define BCM2835_GPHEN0 0x0064 /*!< GPIO Pin High Detect Enable 0 */ +#define BCM2835_GPHEN1 0x0068 /*!< GPIO Pin High Detect Enable 1 */ +#define BCM2835_GPLEN0 0x0070 /*!< GPIO Pin Low Detect Enable 0 */ +#define BCM2835_GPLEN1 0x0074 /*!< GPIO Pin Low Detect Enable 1 */ +#define BCM2835_GPAREN0 0x007c /*!< GPIO Pin Async. Rising Edge Detect 0 */ +#define BCM2835_GPAREN1 0x0080 /*!< GPIO Pin Async. Rising Edge Detect 1 */ +#define BCM2835_GPAFEN0 0x0088 /*!< GPIO Pin Async. Falling Edge Detect 0 */ +#define BCM2835_GPAFEN1 0x008c /*!< GPIO Pin Async. Falling Edge Detect 1 */ +#define BCM2835_GPPUD 0x0094 /*!< GPIO Pin Pull-up/down Enable */ +#define BCM2835_GPPUDCLK0 0x0098 /*!< GPIO Pin Pull-up/down Enable Clock 0 */ +#define BCM2835_GPPUDCLK1 0x009c /*!< GPIO Pin Pull-up/down Enable Clock 1 */ + +/*! \brief bcm2835PortFunction + Port function select modes for bcm2835_gpio_fsel() +*/ +typedef enum +{ + BCM2835_GPIO_FSEL_INPT = 0x00, /*!< Input 0b000 */ + BCM2835_GPIO_FSEL_OUTP = 0x01, /*!< Output 0b001 */ + BCM2835_GPIO_FSEL_ALT0 = 0x04, /*!< Alternate function 0 0b100 */ + BCM2835_GPIO_FSEL_ALT1 = 0x05, /*!< Alternate function 1 0b101 */ + BCM2835_GPIO_FSEL_ALT2 = 0x06, /*!< Alternate function 2 0b110, */ + BCM2835_GPIO_FSEL_ALT3 = 0x07, /*!< Alternate function 3 0b111 */ + BCM2835_GPIO_FSEL_ALT4 = 0x03, /*!< Alternate function 4 0b011 */ + BCM2835_GPIO_FSEL_ALT5 = 0x02, /*!< Alternate function 5 0b010 */ + BCM2835_GPIO_FSEL_MASK = 0x07 /*!< Function select bits mask 0b111 */ +} bcm2835FunctionSelect; + +/*! \brief bcm2835PUDControl + Pullup/Pulldown defines for bcm2835_gpio_pud() +*/ +typedef enum +{ + BCM2835_GPIO_PUD_OFF = 0x00, /*!< Off ? disable pull-up/down 0b00 */ + BCM2835_GPIO_PUD_DOWN = 0x01, /*!< Enable Pull Down control 0b01 */ + BCM2835_GPIO_PUD_UP = 0x02 /*!< Enable Pull Up control 0b10 */ +} bcm2835PUDControl; + +/*! Pad control register offsets from BCM2835_GPIO_PADS */ +#define BCM2835_PADS_GPIO_0_27 0x002c /*!< Pad control register for pads 0 to 27 */ +#define BCM2835_PADS_GPIO_28_45 0x0030 /*!< Pad control register for pads 28 to 45 */ +#define BCM2835_PADS_GPIO_46_53 0x0034 /*!< Pad control register for pads 46 to 53 */ + +/*! Pad Control masks */ +#define BCM2835_PAD_PASSWRD (0x5A << 24) /*!< Password to enable setting pad mask */ +#define BCM2835_PAD_SLEW_RATE_UNLIMITED 0x10 /*!< Slew rate unlimited */ +#define BCM2835_PAD_HYSTERESIS_ENABLED 0x08 /*!< Hysteresis enabled */ +#define BCM2835_PAD_DRIVE_2mA 0x00 /*!< 2mA drive current */ +#define BCM2835_PAD_DRIVE_4mA 0x01 /*!< 4mA drive current */ +#define BCM2835_PAD_DRIVE_6mA 0x02 /*!< 6mA drive current */ +#define BCM2835_PAD_DRIVE_8mA 0x03 /*!< 8mA drive current */ +#define BCM2835_PAD_DRIVE_10mA 0x04 /*!< 10mA drive current */ +#define BCM2835_PAD_DRIVE_12mA 0x05 /*!< 12mA drive current */ +#define BCM2835_PAD_DRIVE_14mA 0x06 /*!< 14mA drive current */ +#define BCM2835_PAD_DRIVE_16mA 0x07 /*!< 16mA drive current */ + +/*! \brief bcm2835PadGroup + Pad group specification for bcm2835_gpio_pad() +*/ +typedef enum +{ + BCM2835_PAD_GROUP_GPIO_0_27 = 0, /*!< Pad group for GPIO pads 0 to 27 */ + BCM2835_PAD_GROUP_GPIO_28_45 = 1, /*!< Pad group for GPIO pads 28 to 45 */ + BCM2835_PAD_GROUP_GPIO_46_53 = 2 /*!< Pad group for GPIO pads 46 to 53 */ +} bcm2835PadGroup; + +/*! \brief GPIO Pin Numbers + + Here we define Raspberry Pin GPIO pins on P1 in terms of the underlying BCM GPIO pin numbers. + These can be passed as a pin number to any function requiring a pin. + Not all pins on the RPi 26 bin IDE plug are connected to GPIO pins + and some can adopt an alternate function. + RPi version 2 has some slightly different pinouts, and these are values RPI_V2_*. + RPi B+ has yet differnet pinouts and these are defined in RPI_BPLUS_*. + At bootup, pins 8 and 10 are set to UART0_TXD, UART0_RXD (ie the alt0 function) respectively + When SPI0 is in use (ie after bcm2835_spi_begin()), SPI0 pins are dedicated to SPI + and cant be controlled independently. + If you are using the RPi Compute Module, just use the GPIO number: there is no need to use one of these + symbolic names +*/ +typedef enum +{ + RPI_GPIO_P1_03 = 0, /*!< Version 1, Pin P1-03 */ + RPI_GPIO_P1_05 = 1, /*!< Version 1, Pin P1-05 */ + RPI_GPIO_P1_07 = 4, /*!< Version 1, Pin P1-07 */ + RPI_GPIO_P1_08 = 14, /*!< Version 1, Pin P1-08, defaults to alt function 0 UART0_TXD */ + RPI_GPIO_P1_10 = 15, /*!< Version 1, Pin P1-10, defaults to alt function 0 UART0_RXD */ + RPI_GPIO_P1_11 = 17, /*!< Version 1, Pin P1-11 */ + RPI_GPIO_P1_12 = 18, /*!< Version 1, Pin P1-12, can be PWM channel 0 in ALT FUN 5 */ + RPI_GPIO_P1_13 = 21, /*!< Version 1, Pin P1-13 */ + RPI_GPIO_P1_15 = 22, /*!< Version 1, Pin P1-15 */ + RPI_GPIO_P1_16 = 23, /*!< Version 1, Pin P1-16 */ + RPI_GPIO_P1_18 = 24, /*!< Version 1, Pin P1-18 */ + RPI_GPIO_P1_19 = 10, /*!< Version 1, Pin P1-19, MOSI when SPI0 in use */ + RPI_GPIO_P1_21 = 9, /*!< Version 1, Pin P1-21, MISO when SPI0 in use */ + RPI_GPIO_P1_22 = 25, /*!< Version 1, Pin P1-22 */ + RPI_GPIO_P1_23 = 11, /*!< Version 1, Pin P1-23, CLK when SPI0 in use */ + RPI_GPIO_P1_24 = 8, /*!< Version 1, Pin P1-24, CE0 when SPI0 in use */ + RPI_GPIO_P1_26 = 7, /*!< Version 1, Pin P1-26, CE1 when SPI0 in use */ + + /* RPi Version 2 */ + RPI_V2_GPIO_P1_03 = 2, /*!< Version 2, Pin P1-03 */ + RPI_V2_GPIO_P1_05 = 3, /*!< Version 2, Pin P1-05 */ + RPI_V2_GPIO_P1_07 = 4, /*!< Version 2, Pin P1-07 */ + RPI_V2_GPIO_P1_08 = 14, /*!< Version 2, Pin P1-08, defaults to alt function 0 UART0_TXD */ + RPI_V2_GPIO_P1_10 = 15, /*!< Version 2, Pin P1-10, defaults to alt function 0 UART0_RXD */ + RPI_V2_GPIO_P1_11 = 17, /*!< Version 2, Pin P1-11 */ + RPI_V2_GPIO_P1_12 = 18, /*!< Version 2, Pin P1-12, can be PWM channel 0 in ALT FUN 5 */ + RPI_V2_GPIO_P1_13 = 27, /*!< Version 2, Pin P1-13 */ + RPI_V2_GPIO_P1_15 = 22, /*!< Version 2, Pin P1-15 */ + RPI_V2_GPIO_P1_16 = 23, /*!< Version 2, Pin P1-16 */ + RPI_V2_GPIO_P1_18 = 24, /*!< Version 2, Pin P1-18 */ + RPI_V2_GPIO_P1_19 = 10, /*!< Version 2, Pin P1-19, MOSI when SPI0 in use */ + RPI_V2_GPIO_P1_21 = 9, /*!< Version 2, Pin P1-21, MISO when SPI0 in use */ + RPI_V2_GPIO_P1_22 = 25, /*!< Version 2, Pin P1-22 */ + RPI_V2_GPIO_P1_23 = 11, /*!< Version 2, Pin P1-23, CLK when SPI0 in use */ + RPI_V2_GPIO_P1_24 = 8, /*!< Version 2, Pin P1-24, CE0 when SPI0 in use */ + RPI_V2_GPIO_P1_26 = 7, /*!< Version 2, Pin P1-26, CE1 when SPI0 in use */ + RPI_V2_GPIO_P1_29 = 5, /*!< Version 2, Pin P1-29 */ + RPI_V2_GPIO_P1_31 = 6, /*!< Version 2, Pin P1-31 */ + RPI_V2_GPIO_P1_32 = 12, /*!< Version 2, Pin P1-32 */ + RPI_V2_GPIO_P1_33 = 13, /*!< Version 2, Pin P1-33 */ + RPI_V2_GPIO_P1_35 = 19, /*!< Version 2, Pin P1-35 */ + RPI_V2_GPIO_P1_36 = 16, /*!< Version 2, Pin P1-36 */ + RPI_V2_GPIO_P1_37 = 26, /*!< Version 2, Pin P1-37 */ + RPI_V2_GPIO_P1_38 = 20, /*!< Version 2, Pin P1-38 */ + RPI_V2_GPIO_P1_40 = 21, /*!< Version 2, Pin P1-40 */ + + /* RPi Version 2, new plug P5 */ + RPI_V2_GPIO_P5_03 = 28, /*!< Version 2, Pin P5-03 */ + RPI_V2_GPIO_P5_04 = 29, /*!< Version 2, Pin P5-04 */ + RPI_V2_GPIO_P5_05 = 30, /*!< Version 2, Pin P5-05 */ + RPI_V2_GPIO_P5_06 = 31, /*!< Version 2, Pin P5-06 */ + + /* RPi B+ J8 header, also RPi 2 40 pin GPIO header */ + RPI_BPLUS_GPIO_J8_03 = 2, /*!< B+, Pin J8-03 */ + RPI_BPLUS_GPIO_J8_05 = 3, /*!< B+, Pin J8-05 */ + RPI_BPLUS_GPIO_J8_07 = 4, /*!< B+, Pin J8-07 */ + RPI_BPLUS_GPIO_J8_08 = 14, /*!< B+, Pin J8-08, defaults to alt function 0 UART0_TXD */ + RPI_BPLUS_GPIO_J8_10 = 15, /*!< B+, Pin J8-10, defaults to alt function 0 UART0_RXD */ + RPI_BPLUS_GPIO_J8_11 = 17, /*!< B+, Pin J8-11 */ + RPI_BPLUS_GPIO_J8_12 = 18, /*!< B+, Pin J8-12, can be PWM channel 0 in ALT FUN 5 */ + RPI_BPLUS_GPIO_J8_13 = 27, /*!< B+, Pin J8-13 */ + RPI_BPLUS_GPIO_J8_15 = 22, /*!< B+, Pin J8-15 */ + RPI_BPLUS_GPIO_J8_16 = 23, /*!< B+, Pin J8-16 */ + RPI_BPLUS_GPIO_J8_18 = 24, /*!< B+, Pin J8-18 */ + RPI_BPLUS_GPIO_J8_19 = 10, /*!< B+, Pin J8-19, MOSI when SPI0 in use */ + RPI_BPLUS_GPIO_J8_21 = 9, /*!< B+, Pin J8-21, MISO when SPI0 in use */ + RPI_BPLUS_GPIO_J8_22 = 25, /*!< B+, Pin J8-22 */ + RPI_BPLUS_GPIO_J8_23 = 11, /*!< B+, Pin J8-23, CLK when SPI0 in use */ + RPI_BPLUS_GPIO_J8_24 = 8, /*!< B+, Pin J8-24, CE0 when SPI0 in use */ + RPI_BPLUS_GPIO_J8_26 = 7, /*!< B+, Pin J8-26, CE1 when SPI0 in use */ + RPI_BPLUS_GPIO_J8_29 = 5, /*!< B+, Pin J8-29, */ + RPI_BPLUS_GPIO_J8_31 = 6, /*!< B+, Pin J8-31, */ + RPI_BPLUS_GPIO_J8_32 = 12, /*!< B+, Pin J8-32, */ + RPI_BPLUS_GPIO_J8_33 = 13, /*!< B+, Pin J8-33, */ + RPI_BPLUS_GPIO_J8_35 = 19, /*!< B+, Pin J8-35, */ + RPI_BPLUS_GPIO_J8_36 = 16, /*!< B+, Pin J8-36, */ + RPI_BPLUS_GPIO_J8_37 = 26, /*!< B+, Pin J8-37, */ + RPI_BPLUS_GPIO_J8_38 = 20, /*!< B+, Pin J8-38, */ + RPI_BPLUS_GPIO_J8_40 = 21 /*!< B+, Pin J8-40, */ +} RPiGPIOPin; + +/* Defines for SPI + GPIO register offsets from BCM2835_SPI0_BASE. + Offsets into the SPI Peripheral block in bytes per 10.5 SPI Register Map +*/ +#define BCM2835_SPI0_CS 0x0000 /*!< SPI Master Control and Status */ +#define BCM2835_SPI0_FIFO 0x0004 /*!< SPI Master TX and RX FIFOs */ +#define BCM2835_SPI0_CLK 0x0008 /*!< SPI Master Clock Divider */ +#define BCM2835_SPI0_DLEN 0x000c /*!< SPI Master Data Length */ +#define BCM2835_SPI0_LTOH 0x0010 /*!< SPI LOSSI mode TOH */ +#define BCM2835_SPI0_DC 0x0014 /*!< SPI DMA DREQ Controls */ + +/* Register masks for SPI0_CS */ +#define BCM2835_SPI0_CS_LEN_LONG 0x02000000 /*!< Enable Long data word in Lossi mode if DMA_LEN is set */ +#define BCM2835_SPI0_CS_DMA_LEN 0x01000000 /*!< Enable DMA mode in Lossi mode */ +#define BCM2835_SPI0_CS_CSPOL2 0x00800000 /*!< Chip Select 2 Polarity */ +#define BCM2835_SPI0_CS_CSPOL1 0x00400000 /*!< Chip Select 1 Polarity */ +#define BCM2835_SPI0_CS_CSPOL0 0x00200000 /*!< Chip Select 0 Polarity */ +#define BCM2835_SPI0_CS_RXF 0x00100000 /*!< RXF - RX FIFO Full */ +#define BCM2835_SPI0_CS_RXR 0x00080000 /*!< RXR RX FIFO needs Reading (full) */ +#define BCM2835_SPI0_CS_TXD 0x00040000 /*!< TXD TX FIFO can accept Data */ +#define BCM2835_SPI0_CS_RXD 0x00020000 /*!< RXD RX FIFO contains Data */ +#define BCM2835_SPI0_CS_DONE 0x00010000 /*!< Done transfer Done */ +#define BCM2835_SPI0_CS_TE_EN 0x00008000 /*!< Unused */ +#define BCM2835_SPI0_CS_LMONO 0x00004000 /*!< Unused */ +#define BCM2835_SPI0_CS_LEN 0x00002000 /*!< LEN LoSSI enable */ +#define BCM2835_SPI0_CS_REN 0x00001000 /*!< REN Read Enable */ +#define BCM2835_SPI0_CS_ADCS 0x00000800 /*!< ADCS Automatically Deassert Chip Select */ +#define BCM2835_SPI0_CS_INTR 0x00000400 /*!< INTR Interrupt on RXR */ +#define BCM2835_SPI0_CS_INTD 0x00000200 /*!< INTD Interrupt on Done */ +#define BCM2835_SPI0_CS_DMAEN 0x00000100 /*!< DMAEN DMA Enable */ +#define BCM2835_SPI0_CS_TA 0x00000080 /*!< Transfer Active */ +#define BCM2835_SPI0_CS_CSPOL 0x00000040 /*!< Chip Select Polarity */ +#define BCM2835_SPI0_CS_CLEAR 0x00000030 /*!< Clear FIFO Clear RX and TX */ +#define BCM2835_SPI0_CS_CLEAR_RX 0x00000020 /*!< Clear FIFO Clear RX */ +#define BCM2835_SPI0_CS_CLEAR_TX 0x00000010 /*!< Clear FIFO Clear TX */ +#define BCM2835_SPI0_CS_CPOL 0x00000008 /*!< Clock Polarity */ +#define BCM2835_SPI0_CS_CPHA 0x00000004 /*!< Clock Phase */ +#define BCM2835_SPI0_CS_CS 0x00000003 /*!< Chip Select */ + +/*! \brief bcm2835SPIBitOrder SPI Bit order + Specifies the SPI data bit ordering for bcm2835_spi_setBitOrder() +*/ +typedef enum +{ + BCM2835_SPI_BIT_ORDER_LSBFIRST = 0, /*!< LSB First */ + BCM2835_SPI_BIT_ORDER_MSBFIRST = 1 /*!< MSB First */ +}bcm2835SPIBitOrder; + +/*! \brief SPI Data mode + Specify the SPI data mode to be passed to bcm2835_spi_setDataMode() +*/ +typedef enum +{ + BCM2835_SPI_MODE0 = 0, /*!< CPOL = 0, CPHA = 0 */ + BCM2835_SPI_MODE1 = 1, /*!< CPOL = 0, CPHA = 1 */ + BCM2835_SPI_MODE2 = 2, /*!< CPOL = 1, CPHA = 0 */ + BCM2835_SPI_MODE3 = 3 /*!< CPOL = 1, CPHA = 1 */ +}bcm2835SPIMode; + +/*! \brief bcm2835SPIChipSelect + Specify the SPI chip select pin(s) +*/ +typedef enum +{ + BCM2835_SPI_CS0 = 0, /*!< Chip Select 0 */ + BCM2835_SPI_CS1 = 1, /*!< Chip Select 1 */ + BCM2835_SPI_CS2 = 2, /*!< Chip Select 2 (ie pins CS1 and CS2 are asserted) */ + BCM2835_SPI_CS_NONE = 3 /*!< No CS, control it yourself */ +} bcm2835SPIChipSelect; + +/*! \brief bcm2835SPIClockDivider + Specifies the divider used to generate the SPI clock from the system clock. + Figures below give the divider, clock period and clock frequency. + Clock divided is based on nominal base clock rate of 250MHz + It is reported that (contrary to the documentation) any even divider may used. + The frequencies shown for each divider have been confirmed by measurement +*/ +typedef enum +{ + BCM2835_SPI_CLOCK_DIVIDER_65536 = 0, /*!< 65536 = 262.144us = 3.814697260kHz */ + BCM2835_SPI_CLOCK_DIVIDER_32768 = 32768, /*!< 32768 = 131.072us = 7.629394531kHz */ + BCM2835_SPI_CLOCK_DIVIDER_16384 = 16384, /*!< 16384 = 65.536us = 15.25878906kHz */ + BCM2835_SPI_CLOCK_DIVIDER_8192 = 8192, /*!< 8192 = 32.768us = 30/51757813kHz */ + BCM2835_SPI_CLOCK_DIVIDER_4096 = 4096, /*!< 4096 = 16.384us = 61.03515625kHz */ + BCM2835_SPI_CLOCK_DIVIDER_2048 = 2048, /*!< 2048 = 8.192us = 122.0703125kHz */ + BCM2835_SPI_CLOCK_DIVIDER_1024 = 1024, /*!< 1024 = 4.096us = 244.140625kHz */ + BCM2835_SPI_CLOCK_DIVIDER_512 = 512, /*!< 512 = 2.048us = 488.28125kHz */ + BCM2835_SPI_CLOCK_DIVIDER_256 = 256, /*!< 256 = 1.024us = 976.5625kHz */ + BCM2835_SPI_CLOCK_DIVIDER_128 = 128, /*!< 128 = 512ns = = 1.953125MHz */ + BCM2835_SPI_CLOCK_DIVIDER_64 = 64, /*!< 64 = 256ns = 3.90625MHz */ + BCM2835_SPI_CLOCK_DIVIDER_32 = 32, /*!< 32 = 128ns = 7.8125MHz */ + BCM2835_SPI_CLOCK_DIVIDER_16 = 16, /*!< 16 = 64ns = 15.625MHz */ + BCM2835_SPI_CLOCK_DIVIDER_8 = 8, /*!< 8 = 32ns = 31.25MHz */ + BCM2835_SPI_CLOCK_DIVIDER_4 = 4, /*!< 4 = 16ns = 62.5MHz */ + BCM2835_SPI_CLOCK_DIVIDER_2 = 2, /*!< 2 = 8ns = 125MHz, fastest you can get */ + BCM2835_SPI_CLOCK_DIVIDER_1 = 1 /*!< 1 = 262.144us = 3.814697260kHz, same as 0/65536 */ +} bcm2835SPIClockDivider; + +/* Defines for I2C + GPIO register offsets from BCM2835_BSC*_BASE. + Offsets into the BSC Peripheral block in bytes per 3.1 BSC Register Map +*/ +#define BCM2835_BSC_C 0x0000 /*!< BSC Master Control */ +#define BCM2835_BSC_S 0x0004 /*!< BSC Master Status */ +#define BCM2835_BSC_DLEN 0x0008 /*!< BSC Master Data Length */ +#define BCM2835_BSC_A 0x000c /*!< BSC Master Slave Address */ +#define BCM2835_BSC_FIFO 0x0010 /*!< BSC Master Data FIFO */ +#define BCM2835_BSC_DIV 0x0014 /*!< BSC Master Clock Divider */ +#define BCM2835_BSC_DEL 0x0018 /*!< BSC Master Data Delay */ +#define BCM2835_BSC_CLKT 0x001c /*!< BSC Master Clock Stretch Timeout */ + +/* Register masks for BSC_C */ +#define BCM2835_BSC_C_I2CEN 0x00008000 /*!< I2C Enable, 0 = disabled, 1 = enabled */ +#define BCM2835_BSC_C_INTR 0x00000400 /*!< Interrupt on RX */ +#define BCM2835_BSC_C_INTT 0x00000200 /*!< Interrupt on TX */ +#define BCM2835_BSC_C_INTD 0x00000100 /*!< Interrupt on DONE */ +#define BCM2835_BSC_C_ST 0x00000080 /*!< Start transfer, 1 = Start a new transfer */ +#define BCM2835_BSC_C_CLEAR_1 0x00000020 /*!< Clear FIFO Clear */ +#define BCM2835_BSC_C_CLEAR_2 0x00000010 /*!< Clear FIFO Clear */ +#define BCM2835_BSC_C_READ 0x00000001 /*!< Read transfer */ + +/* Register masks for BSC_S */ +#define BCM2835_BSC_S_CLKT 0x00000200 /*!< Clock stretch timeout */ +#define BCM2835_BSC_S_ERR 0x00000100 /*!< ACK error */ +#define BCM2835_BSC_S_RXF 0x00000080 /*!< RXF FIFO full, 0 = FIFO is not full, 1 = FIFO is full */ +#define BCM2835_BSC_S_TXE 0x00000040 /*!< TXE FIFO full, 0 = FIFO is not full, 1 = FIFO is full */ +#define BCM2835_BSC_S_RXD 0x00000020 /*!< RXD FIFO contains data */ +#define BCM2835_BSC_S_TXD 0x00000010 /*!< TXD FIFO can accept data */ +#define BCM2835_BSC_S_RXR 0x00000008 /*!< RXR FIFO needs reading (full) */ +#define BCM2835_BSC_S_TXW 0x00000004 /*!< TXW FIFO needs writing (full) */ +#define BCM2835_BSC_S_DONE 0x00000002 /*!< Transfer DONE */ +#define BCM2835_BSC_S_TA 0x00000001 /*!< Transfer Active */ + +#define BCM2835_BSC_FIFO_SIZE 16 /*!< BSC FIFO size */ + +/*! \brief bcm2835I2CClockDivider + Specifies the divider used to generate the I2C clock from the system clock. + Clock divided is based on nominal base clock rate of 250MHz +*/ +typedef enum +{ + BCM2835_I2C_CLOCK_DIVIDER_2500 = 2500, /*!< 2500 = 10us = 100 kHz */ + BCM2835_I2C_CLOCK_DIVIDER_626 = 626, /*!< 622 = 2.504us = 399.3610 kHz */ + BCM2835_I2C_CLOCK_DIVIDER_150 = 150, /*!< 150 = 60ns = 1.666 MHz (default at reset) */ + BCM2835_I2C_CLOCK_DIVIDER_148 = 148 /*!< 148 = 59ns = 1.689 MHz */ +} bcm2835I2CClockDivider; + +/*! \brief bcm2835I2CReasonCodes + Specifies the reason codes for the bcm2835_i2c_write and bcm2835_i2c_read functions. +*/ +typedef enum +{ + BCM2835_I2C_REASON_OK = 0x00, /*!< Success */ + BCM2835_I2C_REASON_ERROR_NACK = 0x01, /*!< Received a NACK */ + BCM2835_I2C_REASON_ERROR_CLKT = 0x02, /*!< Received Clock Stretch Timeout */ + BCM2835_I2C_REASON_ERROR_DATA = 0x04 /*!< Not all data is sent / received */ +} bcm2835I2CReasonCodes; + +/* Defines for ST + GPIO register offsets from BCM2835_ST_BASE. + Offsets into the ST Peripheral block in bytes per 12.1 System Timer Registers + The System Timer peripheral provides four 32-bit timer channels and a single 64-bit free running counter. + BCM2835_ST_CLO is the System Timer Counter Lower bits register. + The system timer free-running counter lower register is a read-only register that returns the current value + of the lower 32-bits of the free running counter. + BCM2835_ST_CHI is the System Timer Counter Upper bits register. + The system timer free-running counter upper register is a read-only register that returns the current value + of the upper 32-bits of the free running counter. +*/ +#define BCM2835_ST_CS 0x0000 /*!< System Timer Control/Status */ +#define BCM2835_ST_CLO 0x0004 /*!< System Timer Counter Lower 32 bits */ +#define BCM2835_ST_CHI 0x0008 /*!< System Timer Counter Upper 32 bits */ + +/*! @} */ + + +/* Defines for PWM, word offsets (ie 4 byte multiples) */ +#define BCM2835_PWM_CONTROL 0 +#define BCM2835_PWM_STATUS 1 +#define BCM2835_PWM_DMAC 2 +#define BCM2835_PWM0_RANGE 4 +#define BCM2835_PWM0_DATA 5 +#define BCM2835_PWM_FIF1 6 +#define BCM2835_PWM1_RANGE 8 +#define BCM2835_PWM1_DATA 9 + +/* Defines for PWM Clock, word offsets (ie 4 byte multiples) */ +#define BCM2835_PWMCLK_CNTL 40 +#define BCM2835_PWMCLK_DIV 41 +#define BCM2835_PWM_PASSWRD (0x5A << 24) /*!< Password to enable setting PWM clock */ + +#define BCM2835_PWM1_MS_MODE 0x8000 /*!< Run in Mark/Space mode */ +#define BCM2835_PWM1_USEFIFO 0x2000 /*!< Data from FIFO */ +#define BCM2835_PWM1_REVPOLAR 0x1000 /*!< Reverse polarity */ +#define BCM2835_PWM1_OFFSTATE 0x0800 /*!< Ouput Off state */ +#define BCM2835_PWM1_REPEATFF 0x0400 /*!< Repeat last value if FIFO empty */ +#define BCM2835_PWM1_SERIAL 0x0200 /*!< Run in serial mode */ +#define BCM2835_PWM1_ENABLE 0x0100 /*!< Channel Enable */ + +#define BCM2835_PWM0_MS_MODE 0x0080 /*!< Run in Mark/Space mode */ +#define BCM2835_PWM_CLEAR_FIFO 0x0040 /*!< Clear FIFO */ +#define BCM2835_PWM0_USEFIFO 0x0020 /*!< Data from FIFO */ +#define BCM2835_PWM0_REVPOLAR 0x0010 /*!< Reverse polarity */ +#define BCM2835_PWM0_OFFSTATE 0x0008 /*!< Ouput Off state */ +#define BCM2835_PWM0_REPEATFF 0x0004 /*!< Repeat last value if FIFO empty */ +#define BCM2835_PWM0_SERIAL 0x0002 /*!< Run in serial mode */ +#define BCM2835_PWM0_ENABLE 0x0001 /*!< Channel Enable */ + +/*! \brief bcm2835PWMClockDivider + Specifies the divider used to generate the PWM clock from the system clock. + Figures below give the divider, clock period and clock frequency. + Clock divided is based on nominal PWM base clock rate of 19.2MHz + The frequencies shown for each divider have been confirmed by measurement +*/ +typedef enum +{ + BCM2835_PWM_CLOCK_DIVIDER_2048 = 2048, /*!< 2048 = 9.375kHz */ + BCM2835_PWM_CLOCK_DIVIDER_1024 = 1024, /*!< 1024 = 18.75kHz */ + BCM2835_PWM_CLOCK_DIVIDER_512 = 512, /*!< 512 = 37.5kHz */ + BCM2835_PWM_CLOCK_DIVIDER_256 = 256, /*!< 256 = 75kHz */ + BCM2835_PWM_CLOCK_DIVIDER_128 = 128, /*!< 128 = 150kHz */ + BCM2835_PWM_CLOCK_DIVIDER_64 = 64, /*!< 64 = 300kHz */ + BCM2835_PWM_CLOCK_DIVIDER_32 = 32, /*!< 32 = 600.0kHz */ + BCM2835_PWM_CLOCK_DIVIDER_16 = 16, /*!< 16 = 1.2MHz */ + BCM2835_PWM_CLOCK_DIVIDER_8 = 8, /*!< 8 = 2.4MHz */ + BCM2835_PWM_CLOCK_DIVIDER_4 = 4, /*!< 4 = 4.8MHz */ + BCM2835_PWM_CLOCK_DIVIDER_2 = 2, /*!< 2 = 9.6MHz, fastest you can get */ + BCM2835_PWM_CLOCK_DIVIDER_1 = 1 /*!< 1 = 4.6875kHz, same as divider 4096 */ +} bcm2835PWMClockDivider; + +/* Historical name compatibility */ +#ifndef BCM2835_NO_DELAY_COMPATIBILITY +#define delay(x) bcm2835_delay(x) +#define delayMicroseconds(x) bcm2835_delayMicroseconds(x) +#endif + +#ifdef __cplusplus +extern "C" { +#endif + + /*! \defgroup init Library initialisation and management + These functions allow you to intialise and control the bcm2835 library + @{ + */ + + /*! Initialise the library by opening /dev/mem and getting pointers to the + internal memory for BCM 2835 device registers. You must call this (successfully) + before calling any other + functions in this library (except bcm2835_set_debug). + If bcm2835_init() fails by returning 0, + calling any other function may result in crashes or other failures. + Prints messages to stderr in case of errors. + \return 1 if successful else 0 + */ + extern int bcm2835_init(void); + + /*! Close the library, deallocating any allocated memory and closing /dev/mem + \return 1 if successful else 0 + */ + extern int bcm2835_close(void); + + /*! Sets the debug level of the library. + A value of 1 prevents mapping to /dev/mem, and makes the library print out + what it would do, rather than accessing the GPIO registers. + A value of 0, the default, causes normal operation. + Call this before calling bcm2835_init(); + \param[in] debug The new debug level. 1 means debug + */ + extern void bcm2835_set_debug(uint8_t debug); + + /*! Returns the version number of the library, same as BCM2835_VERSION + \return the current library version number + */ + extern unsigned int bcm2835_version(void); + + /*! @} */ + + /*! \defgroup lowlevel Low level register access + These functions provide low level register access, and should not generally + need to be used + + @{ + */ + + /*! Gets the base of a register + \param[in] regbase You can use one of the common values BCM2835_REGBASE_* + in \ref bcm2835RegisterBase + \return the register base + \sa Physical Addresses + */ + extern uint32_t* bcm2835_regbase(uint8_t regbase); + + /*! Reads 32 bit value from a peripheral address WITH a memory barrier before and after each read. + This is safe, but slow. The MB before protects this read from any in-flight reads that didn't + use a MB. The MB after protects subsequent reads from another peripheral. + + \param[in] paddr Physical address to read from. See BCM2835_GPIO_BASE etc. + \return the value read from the 32 bit register + \sa Physical Addresses + */ + extern uint32_t bcm2835_peri_read(volatile uint32_t* paddr); + + /*! Reads 32 bit value from a peripheral address WITHOUT the read barriers + You should only use this when: + o your code has previously called bcm2835_peri_read() for a register + within the same peripheral, and no read or write to another peripheral has occurred since. + o your code has called bcm2835_memory_barrier() since the last access to ANOTHER peripheral. + + \param[in] paddr Physical address to read from. See BCM2835_GPIO_BASE etc. + \return the value read from the 32 bit register + \sa Physical Addresses + */ + extern uint32_t bcm2835_peri_read_nb(volatile uint32_t* paddr); + + + /*! Writes 32 bit value from a peripheral address WITH a memory barrier before and after each write + This is safe, but slow. The MB before ensures that any in-flight write to another peripheral + completes before this write is issued. The MB after ensures that subsequent reads and writes + to another peripheral will see the effect of this write. + + This is a tricky optimization; if you aren't sure, use the barrier version. + + \param[in] paddr Physical address to read from. See BCM2835_GPIO_BASE etc. + \param[in] value The 32 bit value to write + \sa Physical Addresses + */ + extern void bcm2835_peri_write(volatile uint32_t* paddr, uint32_t value); + + /*! Writes 32 bit value from a peripheral address without the write barrier + You should only use this when: + o your code has previously called bcm2835_peri_write() for a register + within the same peripheral, and no other peripheral access has occurred since. + o your code has called bcm2835_memory_barrier() since the last access to ANOTHER peripheral. + + This is a tricky optimization; if you aren't sure, use the barrier version. + + \param[in] paddr Physical address to read from. See BCM2835_GPIO_BASE etc. + \param[in] value The 32 bit value to write + \sa Physical Addresses + */ + extern void bcm2835_peri_write_nb(volatile uint32_t* paddr, uint32_t value); + + /*! Alters a number of bits in a 32 peripheral regsiter. + It reads the current valu and then alters the bits defines as 1 in mask, + according to the bit value in value. + All other bits that are 0 in the mask are unaffected. + Use this to alter a subset of the bits in a register. + Memory barriers are used. Note that this is not atomic; an interrupt + routine can cause unexpected results. + \param[in] paddr Physical address to read from. See BCM2835_GPIO_BASE etc. + \param[in] value The 32 bit value to write, masked in by mask. + \param[in] mask Bitmask that defines the bits that will be altered in the register. + \sa Physical Addresses + */ + extern void bcm2835_peri_set_bits(volatile uint32_t* paddr, uint32_t value, uint32_t mask); + /*! @} end of lowlevel */ + + /*! \defgroup gpio GPIO register access + These functions allow you to control the GPIO interface. You can set the + function of each GPIO pin, read the input state and set the output state. + @{ + */ + + /*! Sets the Function Select register for the given pin, which configures + the pin as Input, Output or one of the 6 alternate functions. + \param[in] pin GPIO number, or one of RPI_GPIO_P1_* from \ref RPiGPIOPin. + \param[in] mode Mode to set the pin to, one of BCM2835_GPIO_FSEL_* from \ref bcm2835FunctionSelect + */ + extern void bcm2835_gpio_fsel(uint8_t pin, uint8_t mode); + + /*! Sets the specified pin output to + HIGH. + \param[in] pin GPIO number, or one of RPI_GPIO_P1_* from \ref RPiGPIOPin. + \sa bcm2835_gpio_write() + */ + extern void bcm2835_gpio_set(uint8_t pin); + + /*! Sets the specified pin output to + LOW. + \param[in] pin GPIO number, or one of RPI_GPIO_P1_* from \ref RPiGPIOPin. + \sa bcm2835_gpio_write() + */ + extern void bcm2835_gpio_clr(uint8_t pin); + + /*! Sets any of the first 32 GPIO output pins specified in the mask to + HIGH. + \param[in] mask Mask of pins to affect. Use eg: (1 << RPI_GPIO_P1_03) | (1 << RPI_GPIO_P1_05) + \sa bcm2835_gpio_write_multi() + */ + extern void bcm2835_gpio_set_multi(uint32_t mask); + + /*! Sets any of the first 32 GPIO output pins specified in the mask to + LOW. + \param[in] mask Mask of pins to affect. Use eg: (1 << RPI_GPIO_P1_03) | (1 << RPI_GPIO_P1_05) + \sa bcm2835_gpio_write_multi() + */ + extern void bcm2835_gpio_clr_multi(uint32_t mask); + + /*! Reads the current level on the specified + pin and returns either HIGH or LOW. Works whether or not the pin + is an input or an output. + \param[in] pin GPIO number, or one of RPI_GPIO_P1_* from \ref RPiGPIOPin. + \return the current level either HIGH or LOW + */ + extern uint8_t bcm2835_gpio_lev(uint8_t pin); + + /*! Event Detect Status. + Tests whether the specified pin has detected a level or edge + as requested by bcm2835_gpio_ren(), bcm2835_gpio_fen(), bcm2835_gpio_hen(), + bcm2835_gpio_len(), bcm2835_gpio_aren(), bcm2835_gpio_afen(). + Clear the flag for a given pin by calling bcm2835_gpio_set_eds(pin); + \param[in] pin GPIO number, or one of RPI_GPIO_P1_* from \ref RPiGPIOPin. + \return HIGH if the event detect status for the given pin is true. + */ + extern uint8_t bcm2835_gpio_eds(uint8_t pin); + + /*! Sets the Event Detect Status register for a given pin to 1, + which has the effect of clearing the flag. Use this afer seeing + an Event Detect Status on the pin. + \param[in] pin GPIO number, or one of RPI_GPIO_P1_* from \ref RPiGPIOPin. + */ + extern void bcm2835_gpio_set_eds(uint8_t pin); + + /*! Enable Rising Edge Detect Enable for the specified pin. + When a rising edge is detected, sets the appropriate pin in Event Detect Status. + The GPRENn registers use + synchronous edge detection. This means the input signal is sampled using the + system clock and then it is looking for a ?011? pattern on the sampled signal. This + has the effect of suppressing glitches. + \param[in] pin GPIO number, or one of RPI_GPIO_P1_* from \ref RPiGPIOPin. + */ + extern void bcm2835_gpio_ren(uint8_t pin); + + /*! Disable Rising Edge Detect Enable for the specified pin. + \param[in] pin GPIO number, or one of RPI_GPIO_P1_* from \ref RPiGPIOPin. + */ + extern void bcm2835_gpio_clr_ren(uint8_t pin); + + /*! Enable Falling Edge Detect Enable for the specified pin. + When a falling edge is detected, sets the appropriate pin in Event Detect Status. + The GPRENn registers use + synchronous edge detection. This means the input signal is sampled using the + system clock and then it is looking for a ?100? pattern on the sampled signal. This + has the effect of suppressing glitches. + \param[in] pin GPIO number, or one of RPI_GPIO_P1_* from \ref RPiGPIOPin. + */ + extern void bcm2835_gpio_fen(uint8_t pin); + + /*! Disable Falling Edge Detect Enable for the specified pin. + \param[in] pin GPIO number, or one of RPI_GPIO_P1_* from \ref RPiGPIOPin. + */ + extern void bcm2835_gpio_clr_fen(uint8_t pin); + + /*! Enable High Detect Enable for the specified pin. + When a HIGH level is detected on the pin, sets the appropriate pin in Event Detect Status. + \param[in] pin GPIO number, or one of RPI_GPIO_P1_* from \ref RPiGPIOPin. + */ + extern void bcm2835_gpio_hen(uint8_t pin); + + /*! Disable High Detect Enable for the specified pin. + \param[in] pin GPIO number, or one of RPI_GPIO_P1_* from \ref RPiGPIOPin. + */ + extern void bcm2835_gpio_clr_hen(uint8_t pin); + + /*! Enable Low Detect Enable for the specified pin. + When a LOW level is detected on the pin, sets the appropriate pin in Event Detect Status. + \param[in] pin GPIO number, or one of RPI_GPIO_P1_* from \ref RPiGPIOPin. + */ + extern void bcm2835_gpio_len(uint8_t pin); + + /*! Disable Low Detect Enable for the specified pin. + \param[in] pin GPIO number, or one of RPI_GPIO_P1_* from \ref RPiGPIOPin. + */ + extern void bcm2835_gpio_clr_len(uint8_t pin); + + /*! Enable Asynchronous Rising Edge Detect Enable for the specified pin. + When a rising edge is detected, sets the appropriate pin in Event Detect Status. + Asynchronous means the incoming signal is not sampled by the system clock. As such + rising edges of very short duration can be detected. + \param[in] pin GPIO number, or one of RPI_GPIO_P1_* from \ref RPiGPIOPin. + */ + extern void bcm2835_gpio_aren(uint8_t pin); + + /*! Disable Asynchronous Rising Edge Detect Enable for the specified pin. + \param[in] pin GPIO number, or one of RPI_GPIO_P1_* from \ref RPiGPIOPin. + */ + extern void bcm2835_gpio_clr_aren(uint8_t pin); + + /*! Enable Asynchronous Falling Edge Detect Enable for the specified pin. + When a falling edge is detected, sets the appropriate pin in Event Detect Status. + Asynchronous means the incoming signal is not sampled by the system clock. As such + falling edges of very short duration can be detected. + \param[in] pin GPIO number, or one of RPI_GPIO_P1_* from \ref RPiGPIOPin. + */ + extern void bcm2835_gpio_afen(uint8_t pin); + + /*! Disable Asynchronous Falling Edge Detect Enable for the specified pin. + \param[in] pin GPIO number, or one of RPI_GPIO_P1_* from \ref RPiGPIOPin. + */ + extern void bcm2835_gpio_clr_afen(uint8_t pin); + + /*! Sets the Pull-up/down register for the given pin. This is + used with bcm2835_gpio_pudclk() to set the Pull-up/down resistor for the given pin. + However, it is usually more convenient to use bcm2835_gpio_set_pud(). + \param[in] pud The desired Pull-up/down mode. One of BCM2835_GPIO_PUD_* from bcm2835PUDControl + \sa bcm2835_gpio_set_pud() + */ + extern void bcm2835_gpio_pud(uint8_t pud); + + /*! Clocks the Pull-up/down value set earlier by bcm2835_gpio_pud() into the pin. + \param[in] pin GPIO number, or one of RPI_GPIO_P1_* from \ref RPiGPIOPin. + \param[in] on HIGH to clock the value from bcm2835_gpio_pud() into the pin. + LOW to remove the clock. + \sa bcm2835_gpio_set_pud() + */ + extern void bcm2835_gpio_pudclk(uint8_t pin, uint8_t on); + + /*! Reads and returns the Pad Control for the given GPIO group. + \param[in] group The GPIO pad group number, one of BCM2835_PAD_GROUP_GPIO_* + \return Mask of bits from BCM2835_PAD_* from \ref bcm2835PadGroup + */ + extern uint32_t bcm2835_gpio_pad(uint8_t group); + + /*! Sets the Pad Control for the given GPIO group. + \param[in] group The GPIO pad group number, one of BCM2835_PAD_GROUP_GPIO_* + \param[in] control Mask of bits from BCM2835_PAD_* from \ref bcm2835PadGroup. Note + that it is not necessary to include BCM2835_PAD_PASSWRD in the mask as this + is automatically included. + */ + extern void bcm2835_gpio_set_pad(uint8_t group, uint32_t control); + + /*! Delays for the specified number of milliseconds. + Uses nanosleep(), and therefore does not use CPU until the time is up. + However, you are at the mercy of nanosleep(). From the manual for nanosleep(): + If the interval specified in req is not an exact multiple of the granularity + underlying clock (see time(7)), then the interval will be + rounded up to the next multiple. Furthermore, after the sleep completes, + there may still be a delay before the CPU becomes free to once + again execute the calling thread. + \param[in] millis Delay in milliseconds + */ + extern void bcm2835_delay (unsigned int millis); + + /*! Delays for the specified number of microseconds. + Uses a combination of nanosleep() and a busy wait loop on the BCM2835 system timers, + However, you are at the mercy of nanosleep(). From the manual for nanosleep(): + If the interval specified in req is not an exact multiple of the granularity + underlying clock (see time(7)), then the interval will be + rounded up to the next multiple. Furthermore, after the sleep completes, + there may still be a delay before the CPU becomes free to once + again execute the calling thread. + For times less than about 450 microseconds, uses a busy wait on the System Timer. + It is reported that a delay of 0 microseconds on RaspberryPi will in fact + result in a delay of about 80 microseconds. Your mileage may vary. + \param[in] micros Delay in microseconds + */ + extern void bcm2835_delayMicroseconds (uint64_t micros); + + /*! Sets the output state of the specified pin + \param[in] pin GPIO number, or one of RPI_GPIO_P1_* from \ref RPiGPIOPin. + \param[in] on HIGH sets the output to HIGH and LOW to LOW. + */ + extern void bcm2835_gpio_write(uint8_t pin, uint8_t on); + + /*! Sets any of the first 32 GPIO output pins specified in the mask to the state given by on + \param[in] mask Mask of pins to affect. Use eg: (1 << RPI_GPIO_P1_03) | (1 << RPI_GPIO_P1_05) + \param[in] on HIGH sets the output to HIGH and LOW to LOW. + */ + extern void bcm2835_gpio_write_multi(uint32_t mask, uint8_t on); + + /*! Sets the first 32 GPIO output pins specified in the mask to the value given by value + \param[in] value values required for each bit masked in by mask, eg: (1 << RPI_GPIO_P1_03) | (1 << RPI_GPIO_P1_05) + \param[in] mask Mask of pins to affect. Use eg: (1 << RPI_GPIO_P1_03) | (1 << RPI_GPIO_P1_05) + */ + extern void bcm2835_gpio_write_mask(uint32_t value, uint32_t mask); + + /*! Sets the Pull-up/down mode for the specified pin. This is more convenient than + clocking the mode in with bcm2835_gpio_pud() and bcm2835_gpio_pudclk(). + \param[in] pin GPIO number, or one of RPI_GPIO_P1_* from \ref RPiGPIOPin. + \param[in] pud The desired Pull-up/down mode. One of BCM2835_GPIO_PUD_* from bcm2835PUDControl + */ + extern void bcm2835_gpio_set_pud(uint8_t pin, uint8_t pud); + + /*! @} */ + + /*! \defgroup spi SPI access + These functions let you use SPI0 (Serial Peripheral Interface) to + interface with an external SPI device. + @{ + */ + + /*! Start SPI operations. + Forces RPi SPI0 pins P1-19 (MOSI), P1-21 (MISO), P1-23 (CLK), P1-24 (CE0) and P1-26 (CE1) + to alternate function ALT0, which enables those pins for SPI interface. + You should call bcm2835_spi_end() when all SPI funcitons are complete to return the pins to + their default functions + \sa bcm2835_spi_end() + */ + extern void bcm2835_spi_begin(void); + + /*! End SPI operations. + SPI0 pins P1-19 (MOSI), P1-21 (MISO), P1-23 (CLK), P1-24 (CE0) and P1-26 (CE1) + are returned to their default INPUT behaviour. + */ + extern void bcm2835_spi_end(void); + + /*! Sets the SPI bit order + NOTE: has no effect. Not supported by SPI0. + Defaults to + \param[in] order The desired bit order, one of BCM2835_SPI_BIT_ORDER_*, + see \ref bcm2835SPIBitOrder + */ + extern void bcm2835_spi_setBitOrder(uint8_t order); + + /*! Sets the SPI clock divider and therefore the + SPI clock speed. + \param[in] divider The desired SPI clock divider, one of BCM2835_SPI_CLOCK_DIVIDER_*, + see \ref bcm2835SPIClockDivider + */ + extern void bcm2835_spi_setClockDivider(uint16_t divider); + + /*! Sets the SPI data mode + Sets the clock polariy and phase + \param[in] mode The desired data mode, one of BCM2835_SPI_MODE*, + see \ref bcm2835SPIMode + */ + extern void bcm2835_spi_setDataMode(uint8_t mode); + + /*! Sets the chip select pin(s) + When an bcm2835_spi_transfer() is made, the selected pin(s) will be asserted during the + transfer. + \param[in] cs Specifies the CS pins(s) that are used to activate the desired slave. + One of BCM2835_SPI_CS*, see \ref bcm2835SPIChipSelect + */ + extern void bcm2835_spi_chipSelect(uint8_t cs); + + /*! Sets the chip select pin polarity for a given pin + When an bcm2835_spi_transfer() occurs, the currently selected chip select pin(s) + will be asserted to the + value given by active. When transfers are not happening, the chip select pin(s) + return to the complement (inactive) value. + \param[in] cs The chip select pin to affect + \param[in] active Whether the chip select pin is to be active HIGH + */ + extern void bcm2835_spi_setChipSelectPolarity(uint8_t cs, uint8_t active); + + /*! Transfers one byte to and from the currently selected SPI slave. + Asserts the currently selected CS pins (as previously set by bcm2835_spi_chipSelect) + during the transfer. + Clocks the 8 bit value out on MOSI, and simultaneously clocks in data from MISO. + Returns the read data byte from the slave. + Uses polled transfer as per section 10.6.1 of the BCM 2835 ARM Peripherls manual + \param[in] value The 8 bit data byte to write to MOSI + \return The 8 bit byte simultaneously read from MISO + \sa bcm2835_spi_transfern() + */ + extern uint8_t bcm2835_spi_transfer(uint8_t value); + + /*! Transfers any number of bytes to and from the currently selected SPI slave. + Asserts the currently selected CS pins (as previously set by bcm2835_spi_chipSelect) + during the transfer. + Clocks the len 8 bit bytes out on MOSI, and simultaneously clocks in data from MISO. + The data read read from the slave is placed into rbuf. rbuf must be at least len bytes long + Uses polled transfer as per section 10.6.1 of the BCM 2835 ARM Peripherls manual + \param[in] tbuf Buffer of bytes to send. + \param[out] rbuf Received bytes will by put in this buffer + \param[in] len Number of bytes in the tbuf buffer, and the number of bytes to send/received + \sa bcm2835_spi_transfer() + */ + extern void bcm2835_spi_transfernb(char* tbuf, char* rbuf, uint32_t len); + + /*! Transfers any number of bytes to and from the currently selected SPI slave + using bcm2835_spi_transfernb. + The returned data from the slave replaces the transmitted data in the buffer. + \param[in,out] buf Buffer of bytes to send. Received bytes will replace the contents + \param[in] len Number of bytes int eh buffer, and the number of bytes to send/received + \sa bcm2835_spi_transfer() + */ + extern void bcm2835_spi_transfern(char* buf, uint32_t len); + + /*! Transfers any number of bytes to the currently selected SPI slave. + Asserts the currently selected CS pins (as previously set by bcm2835_spi_chipSelect) + during the transfer. + \param[in] buf Buffer of bytes to send. + \param[in] len Number of bytes in the tbuf buffer, and the number of bytes to send + */ + extern void bcm2835_spi_writenb(char* buf, uint32_t len); + + /*! @} */ + + /*! \defgroup i2c I2C access + These functions let you use I2C (The Broadcom Serial Control bus with the Philips + I2C bus/interface version 2.1 January 2000.) to interface with an external I2C device. + @{ + */ + + /*! Start I2C operations. + Forces RPi I2C pins P1-03 (SDA) and P1-05 (SCL) + to alternate function ALT0, which enables those pins for I2C interface. + You should call bcm2835_i2c_end() when all I2C functions are complete to return the pins to + their default functions + \sa bcm2835_i2c_end() + */ + extern void bcm2835_i2c_begin(void); + + /*! End I2C operations. + I2C pins P1-03 (SDA) and P1-05 (SCL) + are returned to their default INPUT behaviour. + */ + extern void bcm2835_i2c_end(void); + + /*! Sets the I2C slave address. + \param[in] addr The I2C slave address. + */ + extern void bcm2835_i2c_setSlaveAddress(uint8_t addr); + + /*! Sets the I2C clock divider and therefore the I2C clock speed. + \param[in] divider The desired I2C clock divider, one of BCM2835_I2C_CLOCK_DIVIDER_*, + see \ref bcm2835I2CClockDivider + */ + extern void bcm2835_i2c_setClockDivider(uint16_t divider); + + /*! Sets the I2C clock divider by converting the baudrate parameter to + the equivalent I2C clock divider. ( see \sa bcm2835_i2c_setClockDivider) + For the I2C standard 100khz you would set baudrate to 100000 + The use of baudrate corresponds to its use in the I2C kernel device + driver. (Of course, bcm2835 has nothing to do with the kernel driver) + */ + extern void bcm2835_i2c_set_baudrate(uint32_t baudrate); + + /*! Transfers any number of bytes to the currently selected I2C slave. + (as previously set by \sa bcm2835_i2c_setSlaveAddress) + \param[in] buf Buffer of bytes to send. + \param[in] len Number of bytes in the buf buffer, and the number of bytes to send. + \return reason see \ref bcm2835I2CReasonCodes + */ + extern uint8_t bcm2835_i2c_write(const char * buf, uint32_t len); + + /*! Transfers any number of bytes from the currently selected I2C slave. + (as previously set by \sa bcm2835_i2c_setSlaveAddress) + \param[in] buf Buffer of bytes to receive. + \param[in] len Number of bytes in the buf buffer, and the number of bytes to received. + \return reason see \ref bcm2835I2CReasonCodes + */ + extern uint8_t bcm2835_i2c_read(char* buf, uint32_t len); + + /*! Allows reading from I2C slaves that require a repeated start (without any prior stop) + to read after the required slave register has been set. For example, the popular + MPL3115A2 pressure and temperature sensor. Note that your device must support or + require this mode. If your device does not require this mode then the standard + combined: + \sa bcm2835_i2c_write + \sa bcm2835_i2c_read + are a better choice. + Will read from the slave previously set by \sa bcm2835_i2c_setSlaveAddress + \param[in] regaddr Buffer containing the slave register you wish to read from. + \param[in] buf Buffer of bytes to receive. + \param[in] len Number of bytes in the buf buffer, and the number of bytes to received. + \return reason see \ref bcm2835I2CReasonCodes + */ + extern uint8_t bcm2835_i2c_read_register_rs(char* regaddr, char* buf, uint32_t len); + + /*! Allows sending an arbitrary number of bytes to I2C slaves before issuing a repeated + start (with no prior stop) and reading a response. + Necessary for devices that require such behavior, such as the MLX90620. + Will write to and read from the slave previously set by \sa bcm2835_i2c_setSlaveAddress + \param[in] cmds Buffer containing the bytes to send before the repeated start condition. + \param[in] cmds_len Number of bytes to send from cmds buffer + \param[in] buf Buffer of bytes to receive. + \param[in] buf_len Number of bytes to receive in the buf buffer. + \return reason see \ref bcm2835I2CReasonCodes + */ + extern uint8_t bcm2835_i2c_write_read_rs(char* cmds, uint32_t cmds_len, char* buf, uint32_t buf_len); + + /*! @} */ + + /*! \defgroup st System Timer access + Allows access to and delays using the System Timer Counter. + @{ + */ + + /*! Read the System Timer Counter register. + \return the value read from the System Timer Counter Lower 32 bits register + */ + extern uint64_t bcm2835_st_read(void); + + /*! Delays for the specified number of microseconds with offset. + \param[in] offset_micros Offset in microseconds + \param[in] micros Delay in microseconds + */ + extern void bcm2835_st_delay(uint64_t offset_micros, uint64_t micros); + + /*! @} */ + + /*! \defgroup pwm Pulse Width Modulation + Allows control of 2 independent PWM channels. A limited subset of GPIO pins + can be connected to one of these 2 channels, allowing PWM control of GPIO pins. + You have to set the desired pin into a particular Alt Fun to PWM output. See the PWM + documentation on the Main Page. + @{ + */ + + /*! Sets the PWM clock divisor, + to control the basic PWM pulse widths. + \param[in] divisor Divides the basic 19.2MHz PWM clock. You can use one of the common + values BCM2835_PWM_CLOCK_DIVIDER_* in \ref bcm2835PWMClockDivider + */ + extern void bcm2835_pwm_set_clock(uint32_t divisor); + + /*! Sets the mode of the given PWM channel, + allowing you to control the PWM mode and enable/disable that channel + \param[in] channel The PWM channel. 0 or 1. + \param[in] markspace Set true if you want Mark-Space mode. 0 for Balanced mode. + \param[in] enabled Set true to enable this channel and produce PWM pulses. + */ + extern void bcm2835_pwm_set_mode(uint8_t channel, uint8_t markspace, uint8_t enabled); + + /*! Sets the maximum range of the PWM output. + The data value can vary between 0 and this range to control PWM output + \param[in] channel The PWM channel. 0 or 1. + \param[in] range The maximum value permitted for DATA. + */ + extern void bcm2835_pwm_set_range(uint8_t channel, uint32_t range); + + /*! Sets the PWM pulse ratio to emit to DATA/RANGE, + where RANGE is set by bcm2835_pwm_set_range(). + \param[in] channel The PWM channel. 0 or 1. + \param[in] data Controls the PWM output ratio as a fraction of the range. + Can vary from 0 to RANGE. + */ + extern void bcm2835_pwm_set_data(uint8_t channel, uint32_t data); + + /*! @} */ +#ifdef __cplusplus +} +#endif + +#endif /* BCM2835_H */ + +/*! @example blink.c + Blinks RPi GPIO pin 11 on and off +*/ + +/*! @example input.c + Reads the state of an RPi input pin +*/ + +/*! @example event.c + Shows how to use event detection on an input pin +*/ + +/*! @example spi.c + Shows how to use SPI interface to transfer a byte to and from an SPI device +*/ + +/*! @example spin.c + Shows how to use SPI interface to transfer a number of bytes to and from an SPI device +*/ + +/*! @example pwm.c + Shows how to use PWM to control GPIO pins +*/ + +/*! @example i2c.c +Command line utility for executing i2c commands with the +Broadcom bcm2835. Contributed by Shahrooz Shahparnia. +*/ + +/*! example gpio.c + Command line utility for executing gpio commands with the + Broadcom bcm2835. Contributed by Shahrooz Shahparnia. +*/ |