Merged fossee master

1 files changed, 60 insertions, 0 deletions

diff --git a/2.3-1/macros/Hardware/RasberryPi/Setup/RPI_pullControl.sci b/2.3-1/macros/Hardware/RasberryPi/Setup/RPI_pullControl.sci
new file mode 100755
index 00000000..6354bf55
--- /dev/null
+++ b/2.3-1/macros/Hardware/RasberryPi/Setup/RPI_pullControl.sci
@@ -0,0 +1,60 @@
+// Copyright (C) 2017 - IIT Bombay - FOSSEE
+//
+// This file must be used under the terms of the CeCILL.
+// This source file is licensed as described in the file COPYING, which
+// you should have received as part of this distribution.  The terms
+// are also available at
+// http://www.cecill.info/licences/Licence_CeCILL_V2-en.txt
+// Organization: FOSSEE, IIT Bombay
+// Email: toolbox@scilab.in
+
+function RPI_pullControl(pin,RMode)
+// Function to change the internal pull up/down resistor setting for a given pin.
+//
+// Calling Sequence
+//  RPI_pullControl(pin,RMode)
+//
+// Parameters
+//  pin : The pin number to act on. Numbering sequence to be followed as initiated using RPI_pinNumbering function.
+//  RMode: The mode for the internal resistance of the given pin.
+//
+// Description
+//  This sets the pull-up or pull-down resistor mode on the given pin, which should be set as an input using the PRI_pinMode function. The internal pull up/down 
+//  resistors have a value of approximately 50KΩ on the Raspberry Pi.
+//
+//  RMode can take values:
+//  <itemizedlist>
+//  <listitem>'up'  -> pull to 3.3v</listitem>
+//  <listitem>'down'-> pull to ground</listitem>
+//  <listitem>'none'-> no pull up/down</listitem>
+//  </itemizedlist>
+//
+//  This function has no effect on the Raspberry Pi’s GPIO pins when in sys mode, set using RPI_pinNumbering function. To activate a pull-up/pull-down, use the gpio 
+//  program in a script before starting the program.
+//
+// Examples
+//  RPI_pullControl(0,'down')
+// See also
+//  RPI_pinNumbering, RPI_pinMode
+//
+// Authors
+//  Jorawar Singh
+//
+// Bibliography
+//  http://wiringpi.com/reference/
+
+    if RMode=='up' then
+        commande="plC#2#"+string(pin)+"#2#";
+    elseif RMode=='down' then
+        commande="plC#2#"+string(pin)+"#1#";
+    elseif RMode=='none' then
+        commande="plC#2#"+string(pin)+"#0#";
+    else
+        error("mode should be one of up/down/none");
+    end
+    if getos()=="Linux" then
+        unix_w("python -c ""import socket;s=socket.socket();s.connect((''"+RPI_piAdress+"'',9077));s.send(''"+commande+"'');print(s.recv(1024));s.close()""");
+    elseif getos()=="Windows" then
+        RPI_winR=dos("python -c ""import socket;s=socket.socket();s.connect((''"+RPI_piAdress+"'',9077));s.send(''"+commande+"'');print(s.recv(1024));s.close()""");
+    end
+endfunction