Changed links and images in Documentation

1 files changed, 8 insertions, 8 deletions

diff --git a/Documentation/Software-Requirements.rst b/Documentation/Software-Requirements.rst
index ce3d504..30be8c1 100644
--- a/Documentation/Software-Requirements.rst
+++ b/Documentation/Software-Requirements.rst
@@ -13,21 +13,21 @@ For windows based system
 ------------------------
 
 The IC is a standalone one without the Bootloader. One of the ways of
-dumping the code, is using an In System Programmer or an ISP. So, for burning the same we use the softwares: AVRDUDE1 - AVR Downloader Uploader is a program for downloading and uploading the on-chip memories of Atmels AVR microcontrollers. It can program the Flash and EEPROM, and where supported by the serial programming protocol, it can program fuse and lock bits. It’s available as WINAVR for Windows and can be downloaded from here [#] '<https://sourceforge.net/projects/winavr/files/WinAVR/20100110>'
+dumping the code, is using an In System Programmer or an ISP. So, for burning the same we use the softwares: AVRDUDE1 - AVR Downloader Uploader is a program for downloading and uploading the on-chip memories of Atmels AVR microcontrollers. It can program the Flash and EEPROM, and where supported by the serial programming protocol, it can program fuse and lock bits. It’s available as WINAVR for Windows and can be downloaded from 'here <https://sourceforge.net/projects/winavr/files/WinAVR/20100110>'.
 
 Setting up WINAVR
 ~~~~~~~~~~~~~~~~~
 
 Step 1: First, open up the start screen and then search : Command Prompt
 
-.. image:: OpenPLC/Images/Figcmd.png
+.. image:: ../Images/Figcmd.png
    :height: 540px
    :width: 550px
    :scale: 150
 
 Step 2: Then, a screen like this shall pop up.
 
-.. image:: OpenPLC/Images/Comm.png
+.. image:: ../Images/Comm.png
    :height: 540px
    :width: 550px
    :scale: 150
@@ -36,15 +36,15 @@ Step 3: Enter into the command prompt for windows: avrdude
 
 You should get prompts and flags mentioned like this, which implies that you have downloaded the software properly.
 
-.. image:: OpenPLC/Images/avrdude1.png
+.. image:: ../Images/avrdude1.png
    :height: 440px
    :width: 650px
    :scale: 100
 
-For Linux based system
+For Ubuntu system
 ~~~~~~~~~~~~~~~~~~~~~~
 
-Instead if you have Linux system, it’s already pre-installed under the
+Instead if you have Ubuntu system, it’s already pre-installed under the
 name AVRDUDE. Just enter the below command line on your terminal
 
 **man avrdude**
@@ -52,7 +52,7 @@ name AVRDUDE. Just enter the below command line on your terminal
 You would see a screen full of text, something like the one below. To
 exit press q. If you don’t get a screen like that, then open Ubuntu Software Center and on the search bar enter avrdude, then install it. Enter the same command into the terminal again and you shall see the manual.
 
-.. image:: OpenPLC/Images/manavrdude.png
+.. image:: ../Images/manavrdude.png
    :height: 540px
    :width: 450px
    :scale: 100
@@ -62,7 +62,7 @@ Setting up the Ld micro executable
 
 To download the software on your Windows system, go to [#] `<http://cq.cx/ladder.pl/>`_ The download is a direct executable, there’s no need to install it.
 
-.. image:: OpenPLC/Images/Downloading-LD-Micro.png
+.. image::../Images/Downloading-LD-Micro.png
    :height: 540px
    :width: 450px
    :scale: 100