summaryrefslogtreecommitdiff
path: root/drivers/eepro100.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/eepro100.c')
-rwxr-xr-xdrivers/eepro100.c948
1 files changed, 948 insertions, 0 deletions
diff --git a/drivers/eepro100.c b/drivers/eepro100.c
new file mode 100755
index 0000000..04c17f6
--- /dev/null
+++ b/drivers/eepro100.c
@@ -0,0 +1,948 @@
+/*
+ * (C) Copyright 2002
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <net.h>
+#include <asm/io.h>
+#include <pci.h>
+#include <miiphy.h>
+
+#undef DEBUG
+
+#if (CONFIG_COMMANDS & CFG_CMD_NET) && defined(CONFIG_NET_MULTI) && \
+ defined(CONFIG_EEPRO100)
+
+ /* Ethernet chip registers.
+ */
+#define SCBStatus 0 /* Rx/Command Unit Status *Word* */
+#define SCBIntAckByte 1 /* Rx/Command Unit STAT/ACK byte */
+#define SCBCmd 2 /* Rx/Command Unit Command *Word* */
+#define SCBIntrCtlByte 3 /* Rx/Command Unit Intr.Control Byte */
+#define SCBPointer 4 /* General purpose pointer. */
+#define SCBPort 8 /* Misc. commands and operands. */
+#define SCBflash 12 /* Flash memory control. */
+#define SCBeeprom 14 /* EEPROM memory control. */
+#define SCBCtrlMDI 16 /* MDI interface control. */
+#define SCBEarlyRx 20 /* Early receive byte count. */
+#define SCBGenControl 28 /* 82559 General Control Register */
+#define SCBGenStatus 29 /* 82559 General Status register */
+
+ /* 82559 SCB status word defnitions
+ */
+#define SCB_STATUS_CX 0x8000 /* CU finished command (transmit) */
+#define SCB_STATUS_FR 0x4000 /* frame received */
+#define SCB_STATUS_CNA 0x2000 /* CU left active state */
+#define SCB_STATUS_RNR 0x1000 /* receiver left ready state */
+#define SCB_STATUS_MDI 0x0800 /* MDI read/write cycle done */
+#define SCB_STATUS_SWI 0x0400 /* software generated interrupt */
+#define SCB_STATUS_FCP 0x0100 /* flow control pause interrupt */
+
+#define SCB_INTACK_MASK 0xFD00 /* all the above */
+
+#define SCB_INTACK_TX (SCB_STATUS_CX | SCB_STATUS_CNA)
+#define SCB_INTACK_RX (SCB_STATUS_FR | SCB_STATUS_RNR)
+
+ /* System control block commands
+ */
+/* CU Commands */
+#define CU_NOP 0x0000
+#define CU_START 0x0010
+#define CU_RESUME 0x0020
+#define CU_STATSADDR 0x0040 /* Load Dump Statistics ctrs addr */
+#define CU_SHOWSTATS 0x0050 /* Dump statistics counters. */
+#define CU_ADDR_LOAD 0x0060 /* Base address to add to CU commands */
+#define CU_DUMPSTATS 0x0070 /* Dump then reset stats counters. */
+
+/* RUC Commands */
+#define RUC_NOP 0x0000
+#define RUC_START 0x0001
+#define RUC_RESUME 0x0002
+#define RUC_ABORT 0x0004
+#define RUC_ADDR_LOAD 0x0006 /* (seems not to clear on acceptance) */
+#define RUC_RESUMENR 0x0007
+
+#define CU_CMD_MASK 0x00f0
+#define RU_CMD_MASK 0x0007
+
+#define SCB_M 0x0100 /* 0 = enable interrupt, 1 = disable */
+#define SCB_SWI 0x0200 /* 1 - cause device to interrupt */
+
+#define CU_STATUS_MASK 0x00C0
+#define RU_STATUS_MASK 0x003C
+
+#define RU_STATUS_IDLE (0<<2)
+#define RU_STATUS_SUS (1<<2)
+#define RU_STATUS_NORES (2<<2)
+#define RU_STATUS_READY (4<<2)
+#define RU_STATUS_NO_RBDS_SUS ((1<<2)|(8<<2))
+#define RU_STATUS_NO_RBDS_NORES ((2<<2)|(8<<2))
+#define RU_STATUS_NO_RBDS_READY ((4<<2)|(8<<2))
+
+ /* 82559 Port interface commands.
+ */
+#define I82559_RESET 0x00000000 /* Software reset */
+#define I82559_SELFTEST 0x00000001 /* 82559 Selftest command */
+#define I82559_SELECTIVE_RESET 0x00000002
+#define I82559_DUMP 0x00000003
+#define I82559_DUMP_WAKEUP 0x00000007
+
+ /* 82559 Eeprom interface.
+ */
+#define EE_SHIFT_CLK 0x01 /* EEPROM shift clock. */
+#define EE_CS 0x02 /* EEPROM chip select. */
+#define EE_DATA_WRITE 0x04 /* EEPROM chip data in. */
+#define EE_WRITE_0 0x01
+#define EE_WRITE_1 0x05
+#define EE_DATA_READ 0x08 /* EEPROM chip data out. */
+#define EE_ENB (0x4800 | EE_CS)
+#define EE_CMD_BITS 3
+#define EE_DATA_BITS 16
+
+ /* The EEPROM commands include the alway-set leading bit.
+ */
+#define EE_EWENB_CMD (4 << addr_len)
+#define EE_WRITE_CMD (5 << addr_len)
+#define EE_READ_CMD (6 << addr_len)
+#define EE_ERASE_CMD (7 << addr_len)
+
+ /* Receive frame descriptors.
+ */
+struct RxFD {
+ volatile u16 status;
+ volatile u16 control;
+ volatile u32 link; /* struct RxFD * */
+ volatile u32 rx_buf_addr; /* void * */
+ volatile u32 count;
+
+ volatile u8 data[PKTSIZE_ALIGN];
+};
+
+#define RFD_STATUS_C 0x8000 /* completion of received frame */
+#define RFD_STATUS_OK 0x2000 /* frame received with no errors */
+
+#define RFD_CONTROL_EL 0x8000 /* 1=last RFD in RFA */
+#define RFD_CONTROL_S 0x4000 /* 1=suspend RU after receiving frame */
+#define RFD_CONTROL_H 0x0010 /* 1=RFD is a header RFD */
+#define RFD_CONTROL_SF 0x0008 /* 0=simplified, 1=flexible mode */
+
+#define RFD_COUNT_MASK 0x3fff
+#define RFD_COUNT_F 0x4000
+#define RFD_COUNT_EOF 0x8000
+
+#define RFD_RX_CRC 0x0800 /* crc error */
+#define RFD_RX_ALIGNMENT 0x0400 /* alignment error */
+#define RFD_RX_RESOURCE 0x0200 /* out of space, no resources */
+#define RFD_RX_DMA_OVER 0x0100 /* DMA overrun */
+#define RFD_RX_SHORT 0x0080 /* short frame error */
+#define RFD_RX_LENGTH 0x0020
+#define RFD_RX_ERROR 0x0010 /* receive error */
+#define RFD_RX_NO_ADR_MATCH 0x0004 /* no address match */
+#define RFD_RX_IA_MATCH 0x0002 /* individual address does not match */
+#define RFD_RX_TCO 0x0001 /* TCO indication */
+
+ /* Transmit frame descriptors
+ */
+struct TxFD { /* Transmit frame descriptor set. */
+ volatile u16 status;
+ volatile u16 command;
+ volatile u32 link; /* void * */
+ volatile u32 tx_desc_addr; /* Always points to the tx_buf_addr element. */
+ volatile s32 count;
+
+ volatile u32 tx_buf_addr0; /* void *, frame to be transmitted. */
+ volatile s32 tx_buf_size0; /* Length of Tx frame. */
+ volatile u32 tx_buf_addr1; /* void *, frame to be transmitted. */
+ volatile s32 tx_buf_size1; /* Length of Tx frame. */
+};
+
+#define TxCB_CMD_TRANSMIT 0x0004 /* transmit command */
+#define TxCB_CMD_SF 0x0008 /* 0=simplified, 1=flexible mode */
+#define TxCB_CMD_NC 0x0010 /* 0=CRC insert by controller */
+#define TxCB_CMD_I 0x2000 /* generate interrupt on completion */
+#define TxCB_CMD_S 0x4000 /* suspend on completion */
+#define TxCB_CMD_EL 0x8000 /* last command block in CBL */
+
+#define TxCB_COUNT_MASK 0x3fff
+#define TxCB_COUNT_EOF 0x8000
+
+ /* The Speedo3 Rx and Tx frame/buffer descriptors.
+ */
+struct descriptor { /* A generic descriptor. */
+ volatile u16 status;
+ volatile u16 command;
+ volatile u32 link; /* struct descriptor * */
+
+ unsigned char params[0];
+};
+
+#define CFG_CMD_EL 0x8000
+#define CFG_CMD_SUSPEND 0x4000
+#define CFG_CMD_INT 0x2000
+#define CFG_CMD_IAS 0x0001 /* individual address setup */
+#define CFG_CMD_CONFIGURE 0x0002 /* configure */
+
+#define CFG_STATUS_C 0x8000
+#define CFG_STATUS_OK 0x2000
+
+ /* Misc.
+ */
+#define NUM_RX_DESC PKTBUFSRX
+#define NUM_TX_DESC 1 /* Number of TX descriptors */
+
+#define TOUT_LOOP 1000000
+
+#define ETH_ALEN 6
+
+static struct RxFD rx_ring[NUM_RX_DESC]; /* RX descriptor ring */
+static struct TxFD tx_ring[NUM_TX_DESC]; /* TX descriptor ring */
+static int rx_next; /* RX descriptor ring pointer */
+static int tx_next; /* TX descriptor ring pointer */
+static int tx_threshold;
+
+/*
+ * The parameters for a CmdConfigure operation.
+ * There are so many options that it would be difficult to document
+ * each bit. We mostly use the default or recommended settings.
+ */
+static const char i82557_config_cmd[] = {
+ 22, 0x08, 0, 0, 0, 0, 0x32, 0x03, 1, /* 1=Use MII 0=Use AUI */
+ 0, 0x2E, 0, 0x60, 0,
+ 0xf2, 0x48, 0, 0x40, 0xf2, 0x80, /* 0x40=Force full-duplex */
+ 0x3f, 0x05,
+};
+static const char i82558_config_cmd[] = {
+ 22, 0x08, 0, 1, 0, 0, 0x22, 0x03, 1, /* 1=Use MII 0=Use AUI */
+ 0, 0x2E, 0, 0x60, 0x08, 0x88,
+ 0x68, 0, 0x40, 0xf2, 0x84, /* Disable FC */
+ 0x31, 0x05,
+};
+
+static void init_rx_ring (struct eth_device *dev);
+static void purge_tx_ring (struct eth_device *dev);
+
+static void read_hw_addr (struct eth_device *dev, bd_t * bis);
+
+static int eepro100_init (struct eth_device *dev, bd_t * bis);
+static int eepro100_send (struct eth_device *dev, volatile void *packet,
+ int length);
+static int eepro100_recv (struct eth_device *dev);
+static void eepro100_halt (struct eth_device *dev);
+
+#if defined(CONFIG_E500) || defined(CONFIG_DB64360) || defined(CONFIG_DB64460)
+#define bus_to_phys(a) (a)
+#define phys_to_bus(a) (a)
+#else
+#define bus_to_phys(a) pci_mem_to_phys((pci_dev_t)dev->priv, a)
+#define phys_to_bus(a) pci_phys_to_mem((pci_dev_t)dev->priv, a)
+#endif
+
+static inline int INW (struct eth_device *dev, u_long addr)
+{
+ return le16_to_cpu (*(volatile u16 *) (addr + dev->iobase));
+}
+
+static inline void OUTW (struct eth_device *dev, int command, u_long addr)
+{
+ *(volatile u16 *) ((addr + dev->iobase)) = cpu_to_le16 (command);
+}
+
+static inline void OUTL (struct eth_device *dev, int command, u_long addr)
+{
+ *(volatile u32 *) ((addr + dev->iobase)) = cpu_to_le32 (command);
+}
+
+#if defined(CONFIG_MII) || (CONFIG_COMMANDS & CFG_CMD_MII)
+static inline int INL (struct eth_device *dev, u_long addr)
+{
+ return le32_to_cpu (*(volatile u32 *) (addr + dev->iobase));
+}
+
+static int get_phyreg (struct eth_device *dev, unsigned char addr,
+ unsigned char reg, unsigned short *value)
+{
+ int cmd;
+ int timeout = 50;
+
+ /* read requested data */
+ cmd = (2 << 26) | ((addr & 0x1f) << 21) | ((reg & 0x1f) << 16);
+ OUTL (dev, cmd, SCBCtrlMDI);
+
+ do {
+ udelay(1000);
+ cmd = INL (dev, SCBCtrlMDI);
+ } while (!(cmd & (1 << 28)) && (--timeout));
+
+ if (timeout == 0)
+ return -1;
+
+ *value = (unsigned short) (cmd & 0xffff);
+
+ return 0;
+}
+
+static int set_phyreg (struct eth_device *dev, unsigned char addr,
+ unsigned char reg, unsigned short value)
+{
+ int cmd;
+ int timeout = 50;
+
+ /* write requested data */
+ cmd = (1 << 26) | ((addr & 0x1f) << 21) | ((reg & 0x1f) << 16);
+ OUTL (dev, cmd | value, SCBCtrlMDI);
+
+ while (!(INL (dev, SCBCtrlMDI) & (1 << 28)) && (--timeout))
+ udelay(1000);
+
+ if (timeout == 0)
+ return -1;
+
+ return 0;
+}
+
+/* Check if given phyaddr is valid, i.e. there is a PHY connected.
+ * Do this by checking model value field from ID2 register.
+ */
+static struct eth_device* verify_phyaddr (char *devname, unsigned char addr)
+{
+ struct eth_device *dev;
+ unsigned short value;
+ unsigned char model;
+
+ dev = eth_get_dev_by_name(devname);
+ if (dev == NULL) {
+ printf("%s: no such device\n", devname);
+ return NULL;
+ }
+
+ /* read id2 register */
+ if (get_phyreg(dev, addr, PHY_PHYIDR2, &value) != 0) {
+ printf("%s: mii read timeout!\n", devname);
+ return NULL;
+ }
+
+ /* get model */
+ model = (unsigned char)((value >> 4) & 0x003f);
+
+ if (model == 0) {
+ printf("%s: no PHY at address %d\n", devname, addr);
+ return NULL;
+ }
+
+ return dev;
+}
+
+static int eepro100_miiphy_read (char *devname, unsigned char addr,
+ unsigned char reg, unsigned short *value)
+{
+ struct eth_device *dev;
+
+ dev = verify_phyaddr(devname, addr);
+ if (dev == NULL)
+ return -1;
+
+ if (get_phyreg(dev, addr, reg, value) != 0) {
+ printf("%s: mii read timeout!\n", devname);
+ return -1;
+ }
+
+ return 0;
+}
+
+static int eepro100_miiphy_write (char *devname, unsigned char addr,
+ unsigned char reg, unsigned short value)
+{
+ struct eth_device *dev;
+
+ dev = verify_phyaddr(devname, addr);
+ if (dev == NULL)
+ return -1;
+
+ if (set_phyreg(dev, addr, reg, value) != 0) {
+ printf("%s: mii write timeout!\n", devname);
+ return -1;
+ }
+
+ return 0;
+}
+
+#endif /* defined(CONFIG_MII) || (CONFIG_COMMANDS & CFG_CMD_MII) */
+
+/* Wait for the chip get the command.
+*/
+static int wait_for_eepro100 (struct eth_device *dev)
+{
+ int i;
+
+ for (i = 0; INW (dev, SCBCmd) & (CU_CMD_MASK | RU_CMD_MASK); i++) {
+ if (i >= TOUT_LOOP) {
+ return 0;
+ }
+ }
+
+ return 1;
+}
+
+static struct pci_device_id supported[] = {
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82557},
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82559},
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82559ER},
+ {}
+};
+
+int eepro100_initialize (bd_t * bis)
+{
+ pci_dev_t devno;
+ int card_number = 0;
+ struct eth_device *dev;
+ u32 iobase, status;
+ int idx = 0;
+
+ while (1) {
+ /* Find PCI device
+ */
+ if ((devno = pci_find_devices (supported, idx++)) < 0) {
+ break;
+ }
+
+ pci_read_config_dword (devno, PCI_BASE_ADDRESS_0, &iobase);
+ iobase &= ~0xf;
+
+#ifdef DEBUG
+ printf ("eepro100: Intel i82559 PCI EtherExpressPro @0x%x\n",
+ iobase);
+#endif
+
+ pci_write_config_dword (devno,
+ PCI_COMMAND,
+ PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+
+ /* Check if I/O accesses and Bus Mastering are enabled.
+ */
+ pci_read_config_dword (devno, PCI_COMMAND, &status);
+ if (!(status & PCI_COMMAND_MEMORY)) {
+ printf ("Error: Can not enable MEM access.\n");
+ continue;
+ }
+
+ if (!(status & PCI_COMMAND_MASTER)) {
+ printf ("Error: Can not enable Bus Mastering.\n");
+ continue;
+ }
+
+ dev = (struct eth_device *) malloc (sizeof *dev);
+
+ sprintf (dev->name, "i82559#%d", card_number);
+ dev->priv = (void *) devno; /* this have to come before bus_to_phys() */
+ dev->iobase = bus_to_phys (iobase);
+ dev->init = eepro100_init;
+ dev->halt = eepro100_halt;
+ dev->send = eepro100_send;
+ dev->recv = eepro100_recv;
+
+ eth_register (dev);
+
+#if defined (CONFIG_MII) || (CONFIG_COMMANDS & CFG_CMD_MII)
+ /* register mii command access routines */
+ miiphy_register(dev->name,
+ eepro100_miiphy_read, eepro100_miiphy_write);
+#endif
+
+ card_number++;
+
+ /* Set the latency timer for value.
+ */
+ pci_write_config_byte (devno, PCI_LATENCY_TIMER, 0x20);
+
+ udelay (10 * 1000);
+
+ read_hw_addr (dev, bis);
+ }
+
+ return card_number;
+}
+
+
+static int eepro100_init (struct eth_device *dev, bd_t * bis)
+{
+ int i, status = 0;
+ int tx_cur;
+ struct descriptor *ias_cmd, *cfg_cmd;
+
+ /* Reset the ethernet controller
+ */
+ OUTL (dev, I82559_SELECTIVE_RESET, SCBPort);
+ udelay (20);
+
+ OUTL (dev, I82559_RESET, SCBPort);
+ udelay (20);
+
+ if (!wait_for_eepro100 (dev)) {
+ printf ("Error: Can not reset ethernet controller.\n");
+ goto Done;
+ }
+ OUTL (dev, 0, SCBPointer);
+ OUTW (dev, SCB_M | RUC_ADDR_LOAD, SCBCmd);
+
+ if (!wait_for_eepro100 (dev)) {
+ printf ("Error: Can not reset ethernet controller.\n");
+ goto Done;
+ }
+ OUTL (dev, 0, SCBPointer);
+ OUTW (dev, SCB_M | CU_ADDR_LOAD, SCBCmd);
+
+ /* Initialize Rx and Tx rings.
+ */
+ init_rx_ring (dev);
+ purge_tx_ring (dev);
+
+ /* Tell the adapter where the RX ring is located.
+ */
+ if (!wait_for_eepro100 (dev)) {
+ printf ("Error: Can not reset ethernet controller.\n");
+ goto Done;
+ }
+
+ OUTL (dev, phys_to_bus ((u32) & rx_ring[rx_next]), SCBPointer);
+ OUTW (dev, SCB_M | RUC_START, SCBCmd);
+
+ /* Send the Configure frame */
+ tx_cur = tx_next;
+ tx_next = ((tx_next + 1) % NUM_TX_DESC);
+
+ cfg_cmd = (struct descriptor *) &tx_ring[tx_cur];
+ cfg_cmd->command = cpu_to_le16 ((CFG_CMD_SUSPEND | CFG_CMD_CONFIGURE));
+ cfg_cmd->status = 0;
+ cfg_cmd->link = cpu_to_le32 (phys_to_bus ((u32) & tx_ring[tx_next]));
+
+ memcpy (cfg_cmd->params, i82558_config_cmd,
+ sizeof (i82558_config_cmd));
+
+ if (!wait_for_eepro100 (dev)) {
+ printf ("Error---CFG_CMD_CONFIGURE: Can not reset ethernet controller.\n");
+ goto Done;
+ }
+
+ OUTL (dev, phys_to_bus ((u32) & tx_ring[tx_cur]), SCBPointer);
+ OUTW (dev, SCB_M | CU_START, SCBCmd);
+
+ for (i = 0;
+ !(le16_to_cpu (tx_ring[tx_cur].status) & CFG_STATUS_C);
+ i++) {
+ if (i >= TOUT_LOOP) {
+ printf ("%s: Tx error buffer not ready\n", dev->name);
+ goto Done;
+ }
+ }
+
+ if (!(le16_to_cpu (tx_ring[tx_cur].status) & CFG_STATUS_OK)) {
+ printf ("TX error status = 0x%08X\n",
+ le16_to_cpu (tx_ring[tx_cur].status));
+ goto Done;
+ }
+
+ /* Send the Individual Address Setup frame
+ */
+ tx_cur = tx_next;
+ tx_next = ((tx_next + 1) % NUM_TX_DESC);
+
+ ias_cmd = (struct descriptor *) &tx_ring[tx_cur];
+ ias_cmd->command = cpu_to_le16 ((CFG_CMD_SUSPEND | CFG_CMD_IAS));
+ ias_cmd->status = 0;
+ ias_cmd->link = cpu_to_le32 (phys_to_bus ((u32) & tx_ring[tx_next]));
+
+ memcpy (ias_cmd->params, dev->enetaddr, 6);
+
+ /* Tell the adapter where the TX ring is located.
+ */
+ if (!wait_for_eepro100 (dev)) {
+ printf ("Error: Can not reset ethernet controller.\n");
+ goto Done;
+ }
+
+ OUTL (dev, phys_to_bus ((u32) & tx_ring[tx_cur]), SCBPointer);
+ OUTW (dev, SCB_M | CU_START, SCBCmd);
+
+ for (i = 0; !(le16_to_cpu (tx_ring[tx_cur].status) & CFG_STATUS_C);
+ i++) {
+ if (i >= TOUT_LOOP) {
+ printf ("%s: Tx error buffer not ready\n",
+ dev->name);
+ goto Done;
+ }
+ }
+
+ if (!(le16_to_cpu (tx_ring[tx_cur].status) & CFG_STATUS_OK)) {
+ printf ("TX error status = 0x%08X\n",
+ le16_to_cpu (tx_ring[tx_cur].status));
+ goto Done;
+ }
+
+ status = 1;
+
+ Done:
+ return status;
+}
+
+static int eepro100_send (struct eth_device *dev, volatile void *packet, int length)
+{
+ int i, status = -1;
+ int tx_cur;
+
+ if (length <= 0) {
+ printf ("%s: bad packet size: %d\n", dev->name, length);
+ goto Done;
+ }
+
+ tx_cur = tx_next;
+ tx_next = (tx_next + 1) % NUM_TX_DESC;
+
+ tx_ring[tx_cur].command = cpu_to_le16 ( TxCB_CMD_TRANSMIT |
+ TxCB_CMD_SF |
+ TxCB_CMD_S |
+ TxCB_CMD_EL );
+ tx_ring[tx_cur].status = 0;
+ tx_ring[tx_cur].count = cpu_to_le32 (tx_threshold);
+ tx_ring[tx_cur].link =
+ cpu_to_le32 (phys_to_bus ((u32) & tx_ring[tx_next]));
+ tx_ring[tx_cur].tx_desc_addr =
+ cpu_to_le32 (phys_to_bus ((u32) & tx_ring[tx_cur].tx_buf_addr0));
+ tx_ring[tx_cur].tx_buf_addr0 =
+ cpu_to_le32 (phys_to_bus ((u_long) packet));
+ tx_ring[tx_cur].tx_buf_size0 = cpu_to_le32 (length);
+
+ if (!wait_for_eepro100 (dev)) {
+ printf ("%s: Tx error ethernet controller not ready.\n",
+ dev->name);
+ goto Done;
+ }
+
+ /* Send the packet.
+ */
+ OUTL (dev, phys_to_bus ((u32) & tx_ring[tx_cur]), SCBPointer);
+ OUTW (dev, SCB_M | CU_START, SCBCmd);
+
+ for (i = 0; !(le16_to_cpu (tx_ring[tx_cur].status) & CFG_STATUS_C);
+ i++) {
+ if (i >= TOUT_LOOP) {
+ printf ("%s: Tx error buffer not ready\n", dev->name);
+ goto Done;
+ }
+ }
+
+ if (!(le16_to_cpu (tx_ring[tx_cur].status) & CFG_STATUS_OK)) {
+ printf ("TX error status = 0x%08X\n",
+ le16_to_cpu (tx_ring[tx_cur].status));
+ goto Done;
+ }
+
+ status = length;
+
+ Done:
+ return status;
+}
+
+static int eepro100_recv (struct eth_device *dev)
+{
+ u16 status, stat;
+ int rx_prev, length = 0;
+
+ stat = INW (dev, SCBStatus);
+ OUTW (dev, stat & SCB_STATUS_RNR, SCBStatus);
+
+ for (;;) {
+ status = le16_to_cpu (rx_ring[rx_next].status);
+
+ if (!(status & RFD_STATUS_C)) {
+ break;
+ }
+
+ /* Valid frame status.
+ */
+ if ((status & RFD_STATUS_OK)) {
+ /* A valid frame received.
+ */
+ length = le32_to_cpu (rx_ring[rx_next].count) & 0x3fff;
+
+ /* Pass the packet up to the protocol
+ * layers.
+ */
+ NetReceive (rx_ring[rx_next].data, length);
+ } else {
+ /* There was an error.
+ */
+ printf ("RX error status = 0x%08X\n", status);
+ }
+
+ rx_ring[rx_next].control = cpu_to_le16 (RFD_CONTROL_S);
+ rx_ring[rx_next].status = 0;
+ rx_ring[rx_next].count = cpu_to_le32 (PKTSIZE_ALIGN << 16);
+
+ rx_prev = (rx_next + NUM_RX_DESC - 1) % NUM_RX_DESC;
+ rx_ring[rx_prev].control = 0;
+
+ /* Update entry information.
+ */
+ rx_next = (rx_next + 1) % NUM_RX_DESC;
+ }
+
+ if (stat & SCB_STATUS_RNR) {
+
+ printf ("%s: Receiver is not ready, restart it !\n", dev->name);
+
+ /* Reinitialize Rx ring.
+ */
+ init_rx_ring (dev);
+
+ if (!wait_for_eepro100 (dev)) {
+ printf ("Error: Can not restart ethernet controller.\n");
+ goto Done;
+ }
+
+ OUTL (dev, phys_to_bus ((u32) & rx_ring[rx_next]), SCBPointer);
+ OUTW (dev, SCB_M | RUC_START, SCBCmd);
+ }
+
+ Done:
+ return length;
+}
+
+static void eepro100_halt (struct eth_device *dev)
+{
+ /* Reset the ethernet controller
+ */
+ OUTL (dev, I82559_SELECTIVE_RESET, SCBPort);
+ udelay (20);
+
+ OUTL (dev, I82559_RESET, SCBPort);
+ udelay (20);
+
+ if (!wait_for_eepro100 (dev)) {
+ printf ("Error: Can not reset ethernet controller.\n");
+ goto Done;
+ }
+ OUTL (dev, 0, SCBPointer);
+ OUTW (dev, SCB_M | RUC_ADDR_LOAD, SCBCmd);
+
+ if (!wait_for_eepro100 (dev)) {
+ printf ("Error: Can not reset ethernet controller.\n");
+ goto Done;
+ }
+ OUTL (dev, 0, SCBPointer);
+ OUTW (dev, SCB_M | CU_ADDR_LOAD, SCBCmd);
+
+ Done:
+ return;
+}
+
+ /* SROM Read.
+ */
+static int read_eeprom (struct eth_device *dev, int location, int addr_len)
+{
+ unsigned short retval = 0;
+ int read_cmd = location | EE_READ_CMD;
+ int i;
+
+ OUTW (dev, EE_ENB & ~EE_CS, SCBeeprom);
+ OUTW (dev, EE_ENB, SCBeeprom);
+
+ /* Shift the read command bits out. */
+ for (i = 12; i >= 0; i--) {
+ short dataval = (read_cmd & (1 << i)) ? EE_DATA_WRITE : 0;
+
+ OUTW (dev, EE_ENB | dataval, SCBeeprom);
+ udelay (1);
+ OUTW (dev, EE_ENB | dataval | EE_SHIFT_CLK, SCBeeprom);
+ udelay (1);
+ }
+ OUTW (dev, EE_ENB, SCBeeprom);
+
+ for (i = 15; i >= 0; i--) {
+ OUTW (dev, EE_ENB | EE_SHIFT_CLK, SCBeeprom);
+ udelay (1);
+ retval = (retval << 1) |
+ ((INW (dev, SCBeeprom) & EE_DATA_READ) ? 1 : 0);
+ OUTW (dev, EE_ENB, SCBeeprom);
+ udelay (1);
+ }
+
+ /* Terminate the EEPROM access. */
+ OUTW (dev, EE_ENB & ~EE_CS, SCBeeprom);
+ return retval;
+}
+
+#ifdef CONFIG_EEPRO100_SROM_WRITE
+int eepro100_write_eeprom (struct eth_device* dev, int location, int addr_len, unsigned short data)
+{
+ unsigned short dataval;
+ int enable_cmd = 0x3f | EE_EWENB_CMD;
+ int write_cmd = location | EE_WRITE_CMD;
+ int i;
+ unsigned long datalong, tmplong;
+
+ OUTW(dev, EE_ENB & ~EE_CS, SCBeeprom);
+ udelay(1);
+ OUTW(dev, EE_ENB, SCBeeprom);
+
+ /* Shift the enable command bits out. */
+ for (i = (addr_len+EE_CMD_BITS-1); i >= 0; i--)
+ {
+ dataval = (enable_cmd & (1 << i)) ? EE_DATA_WRITE : 0;
+ OUTW(dev, EE_ENB | dataval, SCBeeprom);
+ udelay(1);
+ OUTW(dev, EE_ENB | dataval | EE_SHIFT_CLK, SCBeeprom);
+ udelay(1);
+ }
+
+ OUTW(dev, EE_ENB, SCBeeprom);
+ udelay(1);
+ OUTW(dev, EE_ENB & ~EE_CS, SCBeeprom);
+ udelay(1);
+ OUTW(dev, EE_ENB, SCBeeprom);
+
+
+ /* Shift the write command bits out. */
+ for (i = (addr_len+EE_CMD_BITS-1); i >= 0; i--)
+ {
+ dataval = (write_cmd & (1 << i)) ? EE_DATA_WRITE : 0;
+ OUTW(dev, EE_ENB | dataval, SCBeeprom);
+ udelay(1);
+ OUTW(dev, EE_ENB | dataval | EE_SHIFT_CLK, SCBeeprom);
+ udelay(1);
+ }
+
+ /* Write the data */
+ datalong= (unsigned long) ((((data) & 0x00ff) << 8) | ( (data) >> 8));
+
+ for (i = 0; i< EE_DATA_BITS; i++)
+ {
+ /* Extract and move data bit to bit DI */
+ dataval = ((datalong & 0x8000)>>13) ? EE_DATA_WRITE : 0;
+
+ OUTW(dev, EE_ENB | dataval, SCBeeprom);
+ udelay(1);
+ OUTW(dev, EE_ENB | dataval | EE_SHIFT_CLK, SCBeeprom);
+ udelay(1);
+ OUTW(dev, EE_ENB | dataval, SCBeeprom);
+ udelay(1);
+
+ datalong = datalong << 1; /* Adjust significant data bit*/
+ }
+
+ /* Finish up command (toggle CS) */
+ OUTW(dev, EE_ENB & ~EE_CS, SCBeeprom);
+ udelay(1); /* delay for more than 250 ns */
+ OUTW(dev, EE_ENB, SCBeeprom);
+
+ /* Wait for programming ready (D0 = 1) */
+ tmplong = 10;
+ do
+ {
+ dataval = INW(dev, SCBeeprom);
+ if (dataval & EE_DATA_READ)
+ break;
+ udelay(10000);
+ }
+ while (-- tmplong);
+
+ if (tmplong == 0)
+ {
+ printf ("Write i82559 eeprom timed out (100 ms waiting for data ready.\n");
+ return -1;
+ }
+
+ /* Terminate the EEPROM access. */
+ OUTW(dev, EE_ENB & ~EE_CS, SCBeeprom);
+
+ return 0;
+}
+#endif
+
+static void init_rx_ring (struct eth_device *dev)
+{
+ int i;
+
+ for (i = 0; i < NUM_RX_DESC; i++) {
+ rx_ring[i].status = 0;
+ rx_ring[i].control =
+ (i == NUM_RX_DESC - 1) ? cpu_to_le16 (RFD_CONTROL_S) : 0;
+ rx_ring[i].link =
+ cpu_to_le32 (phys_to_bus
+ ((u32) & rx_ring[(i + 1) % NUM_RX_DESC]));
+ rx_ring[i].rx_buf_addr = 0xffffffff;
+ rx_ring[i].count = cpu_to_le32 (PKTSIZE_ALIGN << 16);
+ }
+
+ rx_next = 0;
+}
+
+static void purge_tx_ring (struct eth_device *dev)
+{
+ int i;
+
+ tx_next = 0;
+ tx_threshold = 0x01208000;
+
+ for (i = 0; i < NUM_TX_DESC; i++) {
+ tx_ring[i].status = 0;
+ tx_ring[i].command = 0;
+ tx_ring[i].link = 0;
+ tx_ring[i].tx_desc_addr = 0;
+ tx_ring[i].count = 0;
+
+ tx_ring[i].tx_buf_addr0 = 0;
+ tx_ring[i].tx_buf_size0 = 0;
+ tx_ring[i].tx_buf_addr1 = 0;
+ tx_ring[i].tx_buf_size1 = 0;
+ }
+}
+
+static void read_hw_addr (struct eth_device *dev, bd_t * bis)
+{
+ u16 eeprom[0x40];
+ u16 sum = 0;
+ int i, j;
+ int addr_len = read_eeprom (dev, 0, 6) == 0xffff ? 8 : 6;
+
+ for (j = 0, i = 0; i < 0x40; i++) {
+ u16 value = read_eeprom (dev, i, addr_len);
+
+ eeprom[i] = value;
+ sum += value;
+ if (i < 3) {
+ dev->enetaddr[j++] = value;
+ dev->enetaddr[j++] = value >> 8;
+ }
+ }
+
+ if (sum != 0xBABA) {
+ memset (dev->enetaddr, 0, ETH_ALEN);
+#ifdef DEBUG
+ printf ("%s: Invalid EEPROM checksum %#4.4x, "
+ "check settings before activating this device!\n",
+ dev->name, sum);
+#endif
+ }
+}
+
+#endif
generated by cgit (git 2.34.1) at 2024-12-22 22:18:55 +0000