init commit via android 4.4 uboot

1 files changed, 766 insertions, 0 deletions

diff --git a/include/configs/GEN860T.h b/include/configs/GEN860T.h
new file mode 100755
index 0000000..de8f7ae
--- /dev/null
+++ b/include/configs/GEN860T.h
@@ -0,0 +1,766 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ * Keith Outwater, keith_outwater@mvis.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config_GEN860T.h - board specific configuration options
+ */
+
+#ifndef __CONFIG_GEN860T_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_MPC860
+#define CONFIG_GEN860T
+
+/*
+ * Identify the board
+ */
+#if !defined(CONFIG_SC)
+#define CONFIG_IDENT_STRING				" B2"
+#else
+#define CONFIG_IDENT_STRING				" SC"
+#endif
+
+/*
+ * Don't depend on the RTC clock to determine clock frequency -
+ * the 860's internal rtc uses a 32.768 KHz clock which is
+ * generated by the DS1337 - and the DS1337 clock can be turned off.
+ */
+#if !defined(CONFIG_SC)
+#define	CONFIG_8xx_GCLK_FREQ			66600000
+#else
+#define	CONFIG_8xx_GCLK_FREQ			48000000
+#endif
+
+/*
+ * The RS-232 console port is on SMC1
+ */
+#define	CONFIG_8xx_CONS_SMC1
+#define CONFIG_BAUDRATE					38400
+
+/*
+ * Set allowable console baud rates
+ */
+#define CFG_BAUDRATE_TABLE				{ 9600,		\
+							 		 	  19200,	\
+							 		 	  38400,	\
+									 	  57600,	\
+									 	  115200,	\
+										}
+
+/*
+ * Print console information
+ */
+#undef	 CFG_CONSOLE_INFO_QUIET
+
+/*
+ * Set the autoboot delay in seconds.  A delay of -1 disables autoboot
+ */
+#define CONFIG_BOOTDELAY				5
+
+/*
+ * Pass the clock frequency to the Linux kernel in units of MHz
+ */
+#define	CONFIG_CLOCKS_IN_MHZ
+
+#define CONFIG_PREBOOT		\
+	"echo;echo"
+
+#undef	CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND	\
+	"bootp;" \
+	"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
+	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
+	"bootm"
+
+/*
+ * Turn off echo for serial download by default.  Allow baud rate to be changed
+ * for downloads
+ */
+#undef	CONFIG_LOADS_ECHO
+#define	CFG_LOADS_BAUD_CHANGE
+
+/*
+ * Set default load address for tftp network downloads
+ */
+#define	CFG_TFTP_LOADADDR				0x01000000
+
+/*
+ * Turn off the watchdog timer
+ */
+#undef	CONFIG_WATCHDOG
+
+/*
+ * Do not reboot if a panic occurs
+ */
+#define CONFIG_PANIC_HANG
+
+/*
+ * Enable the status LED
+ */
+#define	CONFIG_STATUS_LED
+
+/*
+ * Reset address. We pick an address such that when an instruction
+ * is executed at that address, a machine check exception occurs
+ */
+#define CFG_RESET_ADDRESS				((ulong) -1)
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_MASK				( CONFIG_BOOTP_DEFAULT		| \
+									  	  CONFIG_BOOTP_BOOTFILESIZE   \
+										)
+
+/*
+ * The GEN860T network interface uses the on-chip 10/100 FEC with
+ * an Intel LXT971A PHY connected to the 860T's MII. The PHY's
+ * MII address is hardwired on the board to zero.
+ */
+#define CONFIG_FEC_ENET
+#define CFG_DISCOVER_PHY
+#define CONFIG_MII
+#define CONFIG_PHY_ADDR         		0
+
+/*
+ * Set default IP stuff just to get bootstrap entries into the
+ * environment so that we can autoscript the full default environment.
+ */
+#define CONFIG_ETHADDR					9a:52:63:15:85:25
+#define CONFIG_SERVERIP					10.0.4.201
+#define CONFIG_IPADDR					10.0.4.111
+
+/*
+ * This board has a 32 kibibyte EEPROM (Atmel AT24C256) connected to
+ * the MPC860T I2C interface.
+ */
+#define CFG_I2C_EEPROM_ADDR				0x50
+#define CFG_EEPROM_PAGE_WRITE_BITS		6		/* 64 byte pages		*/
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	12		/* 10 mS w/ 20% margin	*/
+#define	CFG_I2C_EEPROM_ADDR_LEN			2		/* need 16 bit address	*/
+#define CFG_ENV_EEPROM_SIZE				(32 * 1024)
+
+/*
+ * Enable I2C and select the hardware/software driver
+ */
+#define CONFIG_HARD_I2C		1				/* CPM based I2C			*/
+#undef	CONFIG_SOFT_I2C        				/* Bit-banged I2C			*/
+
+#ifdef CONFIG_HARD_I2C
+#define	CFG_I2C_SPEED		100000			/* clock speed in Hz		*/
+#define CFG_I2C_SLAVE		0xFE			/* I2C slave address		*/
+#endif
+
+#ifdef CONFIG_SOFT_I2C
+#define PB_SCL				0x00000020		/* PB 26					*/
+#define PB_SDA				0x00000010		/* PB 27 					*/
+#define I2C_INIT			(immr->im_cpm.cp_pbdir |=  PB_SCL)
+#define I2C_ACTIVE			(immr->im_cpm.cp_pbdir |=  PB_SDA)
+#define I2C_TRISTATE		(immr->im_cpm.cp_pbdir &= ~PB_SDA)
+#define I2C_READ			((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
+#define I2C_SDA(bit)		if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
+								else    immr->im_cpm.cp_pbdat &= ~PB_SDA
+#define I2C_SCL(bit)		if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
+								else    immr->im_cpm.cp_pbdat &= ~PB_SCL
+#define I2C_DELAY			udelay(5)		/* 1/4 I2C clock duration	*/
+#endif
+
+/*
+ * Allow environment overwrites by anyone
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#if !defined(CONFIG_SC)
+/*
+ * The MPC860's internal RTC is horribly broken in rev D masks. Three
+ * internal MPC860T circuit nodes were inadvertently left floating; this
+ * causes KAPWR current in power down mode to be three orders of magnitude
+ * higher than specified in the datasheet (from 10 uA to 10 mA).  No
+ * reasonable battery can keep that kind RTC running during powerdown for any
+ * length of time, so we use an external RTC on the I2C bus instead.
+ */
+#define CONFIG_RTC_DS1337
+#define CFG_I2C_RTC_ADDR				0x68
+
+#else
+/*
+ * No external RTC on SC variant, so we're stuck with the internal one.
+ */
+#define	CONFIG_RTC_MPC8xx
+#endif
+
+/*
+ * Power On Self Test support
+ */
+#define CONFIG_POST			  ( CFG_POST_CACHE		| \
+								CFG_POST_MEMORY		| \
+								CFG_POST_CPU		| \
+								CFG_POST_UART		| \
+								CFG_POST_SPR )
+
+#ifdef CONFIG_POST
+#define CFG_CMD_POST_DIAG CFG_CMD_DIAG
+#else
+#define CFG_CMD_POST_DIAG		0
+#endif
+
+/*
+ * List of available monitor commands.  Use the system default list
+ * plus add some of the "non-standard" commands back in.
+ * See ./cmd_confdefs.h
+ */
+#define BASE_CONFIG_COMMANDS	( CONFIG_CMD_DFL	| \
+								CFG_CMD_ASKENV	| \
+								CFG_CMD_DHCP	| \
+								CFG_CMD_I2C		| \
+								CFG_CMD_EEPROM	| \
+								CFG_CMD_REGINFO	| \
+								CFG_CMD_IMMAP	| \
+								CFG_CMD_ELF		| \
+								CFG_CMD_DATE	| \
+								CFG_CMD_FPGA	| \
+								CFG_CMD_MII 	| \
+								CFG_CMD_BEDBUG	| \
+								CFG_CMD_POST_DIAG )
+
+#if !defined(CONFIG_SC)
+#define	CONFIG_COMMANDS ( BASE_CONFIG_COMMANDS | CFG_CMD_DOC )
+#else
+#define CONFIG_COMMANDS	BASE_CONFIG_COMMANDS
+#endif
+
+/*
+ * There is no IDE/PCMCIA hardware support on the board.
+ */
+#undef  CONFIG_IDE_PCMCIA
+#undef  CONFIG_IDE_LED
+#undef  CONFIG_IDE_RESET
+
+/*
+ * Enable the call to misc_init_r() for miscellaneous platform
+ * dependent initialization.
+ */
+#define CONFIG_MISC_INIT_R
+
+/*
+ * Enable call to last_stage_init() so we can twiddle some LEDS :)
+ */
+#define CONFIG_LAST_STAGE_INIT
+
+/*
+ * Virtex2 FPGA configuration support
+ */
+#define CONFIG_FPGA_COUNT		1
+#define CONFIG_FPGA				CFG_XILINX_VIRTEX2
+#define CFG_FPGA_PROG_FEEDBACK
+
+
+/************************************************************************
+ * This must be included AFTER the definition of any CONFIG_COMMANDS
+ */
+#include <cmd_confdefs.h>
+
+/*
+ * Verbose help from command monitor.
+ */
+#define	CFG_LONGHELP
+#if !defined(CONFIG_SC)
+#define	CFG_PROMPT			"B2> "
+#else
+#define	CFG_PROMPT			"SC> "
+#endif
+
+
+/*
+ * Use the "hush" command parser
+ */
+#define	CFG_HUSH_PARSER
+#define	CFG_PROMPT_HUSH_PS2	"> "
+
+/*
+ * Set buffer size for console I/O
+ */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define	CFG_CBSIZE			1024
+#else
+#define	CFG_CBSIZE			256
+#endif
+
+/*
+ * Print buffer size
+ */
+#define	CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16)
+
+/*
+ * Maximum number of arguments that a command can accept
+ */
+#define	CFG_MAXARGS			16
+
+/*
+ * Boot argument buffer size
+ */
+#define CFG_BARGSIZE		CFG_CBSIZE
+
+/*
+ * Default memory test range
+ */
+#define CFG_MEMTEST_START	0x0100000
+#define CFG_MEMTEST_END		(CFG_MEMTEST_START  + (128 * 1024))
+
+/*
+ * Select the more full-featured memory test
+ */
+#define	CFG_ALT_MEMTEST
+
+/*
+ * Default load address
+ */
+#define	CFG_LOAD_ADDR		0x01000000
+
+/*
+ * Set decrementer frequency (1 ms ticks)
+ */
+#define	CFG_HZ				1000
+
+/*
+ * Device memory map (after SDRAM remap to 0x0):
+ *
+ * CS		Device				Base Addr	Size
+ * ----------------------------------------------------
+ * CS0*		Flash				0x40000000	64 M
+ * CS1*		SDRAM				0x00000000	16 M
+ * CS2*		Disk-On-Chip		0x50000000	32 K
+ * CS3*		FPGA				0x60000000	64 M
+ * CS4*		SelectMap			0x70000000	32 K
+ * CS5*		Mil-Std 1553 I/F	0x80000000	32 K
+ * CS6*		Unused
+ * CS7*		Unused
+ * IMMR		860T Registers		0xfff00000
+ */
+
+/*
+ * Base addresses and block sizes
+ */
+#define CFG_IMMR			0xFF000000
+
+#define SDRAM_BASE			0x00000000
+#define SDRAM_SIZE			(64 * 1024 * 1024)
+
+#define FLASH_BASE			0x40000000
+#define FLASH_SIZE			(16 * 1024 * 1024)
+
+#define DOC_BASE			0x50000000
+#define DOC_SIZE			(32 * 1024)
+
+#define FPGA_BASE			0x60000000
+#define FPGA_SIZE			(64 * 1024 * 1024)
+
+#define SELECTMAP_BASE		0x70000000
+#define SELECTMAP_SIZE		(32 * 1024)
+
+#define M1553_BASE			0x80000000
+#define M1553_SIZE			(64 * 1024)
+
+/*
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR		CFG_IMMR
+#define	CFG_INIT_RAM_END		0x2F00	/* End of used area in DPRAM		*/
+#define	CFG_INIT_DATA_SIZE		64  	/* # bytes reserved for initial data*/
+#define CFG_GBL_DATA_OFFSET		(CFG_INIT_RAM_END - CFG_INIT_DATA_SIZE)
+#define	CFG_INIT_SP_OFFSET		CFG_GBL_DATA_OFFSET
+
+/*
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define	CFG_SDRAM_BASE			SDRAM_BASE
+
+/*
+ * FLASH organization
+ */
+#define CFG_FLASH_BASE			FLASH_BASE
+#define CFG_FLASH_SIZE			FLASH_SIZE
+#define CFG_FLASH_SECT_SIZE		(128 * 1024)
+#define CFG_MAX_FLASH_BANKS		1
+#define CFG_MAX_FLASH_SECT		128
+
+/*
+ * The timeout values are for an entire chip and are in milliseconds.
+ * Yes I know that the write timeout is huge.  Accroding to the
+ * datasheet a single byte takes 630 uS (round to 1 ms) max at worst
+ * case VCC and temp after 100K programming cycles.  It works out
+ * to 280 minutes (might as well be forever).
+ */
+#define CFG_FLASH_ERASE_TOUT	(CFG_MAX_FLASH_SECT * 5000)
+#define CFG_FLASH_WRITE_TOUT	(CFG_MAX_FLASH_SECT * 128 * 1024 * 1)
+
+/*
+ * Allow direct writes to FLASH from tftp transfers (** dangerous **)
+ */
+#define	CFG_DIRECT_FLASH_TFTP
+
+/*
+ * Reserve memory for U-Boot.
+ */
+#define CFG_MAX_UBOOT_SECTS		4
+#define	CFG_MONITOR_LEN			(CFG_MAX_UBOOT_SECTS * CFG_FLASH_SECT_SIZE)
+#define CFG_MONITOR_BASE		CFG_FLASH_BASE
+
+/*
+ * Select environment placement.  NOTE that u-boot.lds must
+ * be edited if this is changed!
+ */
+#undef	CFG_ENV_IS_IN_FLASH
+#define CFG_ENV_IS_IN_EEPROM
+
+#if defined(CFG_ENV_IS_IN_EEPROM)
+#define CFG_ENV_SIZE			(2 * 1024)
+#define CFG_ENV_OFFSET			(CFG_ENV_EEPROM_SIZE - (8 * 1024))
+#else
+#define CFG_ENV_SIZE			0x1000
+#define CFG_ENV_SECT_SIZE		CFG_FLASH_SECT_SIZE
+
+/*
+ * This ultimately gets passed right into the linker script, so we have to
+ * use a number :(
+ */
+#define CFG_ENV_OFFSET			0x060000
+#endif
+
+/*
+ * Reserve memory for malloc()
+ */
+#define	CFG_MALLOC_LEN		(128 * 1024)
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define	CFG_BOOTMAPSZ		(8 * 1024 * 1024)
+
+/*
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE		16	/* For all MPC8xx CPUs				*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT		4	/* log base 2 of above value		*/
+#endif
+
+/*------------------------------------------------------------------------
+ * SYPCR - System Protection Control							UM 11-9
+ * -----------------------------------------------------------------------
+ * SYPCR can only be written once after reset!
+ *
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR	( SYPCR_SWTC	| \
+					  SYPCR_BMT 	| \
+					  SYPCR_BME 	| \
+					  SYPCR_SWF 	| \
+					  SYPCR_SWE 	| \
+					  SYPCR_SWRI	| \
+					  SYPCR_SWP		  \
+					)
+#else
+#define CFG_SYPCR	( SYPCR_SWTC	| \
+					  SYPCR_BMT 	| \
+					  SYPCR_BME 	| \
+					  SYPCR_SWF 	| \
+					  SYPCR_SWP		  \
+					)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration							UM 11-6
+ *-----------------------------------------------------------------------
+ * Set debug pin mux, enable SPKROUT and GPLB5*.
+ */
+#define CFG_SIUMCR	( SIUMCR_DBGC11 | \
+					  SIUMCR_DBPC11 | \
+					  SIUMCR_MLRC11	| \
+					  SIUMCR_GB5E	  \
+					)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control							UM 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freeze enabled
+ */
+#define CFG_TBSCR	( TBSCR_REFA | \
+					  TBSCR_REFB | \
+					  TBSCR_TBF	   \
+					)
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register			UM 11-27
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RTCSC	( RTCSC_SEC	| \
+					  RTCSC_ALR | \
+					  RTCSC_RTF | \
+					  RTCSC_RTE	  \
+					)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control				UM 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR	( PISCR_PS		| \
+					  PISCR_PITF	  \
+					)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register			UM 15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit. Set MF for 1:2:1 mode.
+ */
+#define CFG_PLPRCR	( ((0x1 << PLPRCR_MF_SHIFT) & PLPRCR_MF_MSK)	| \
+					  PLPRCR_SPLSS	| \
+					  PLPRCR_TEXPS	| \
+					  PLPRCR_TMIST	  \
+					)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register				UM 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK   SCCR_EBDF11
+
+#if !defined(CONFIG_SC)
+#define CFG_SCCR	( SCCR_TBS			| 	/* timebase = GCLK/2	*/ \
+					  SCCR_COM00   		| 	/* full strength CLKOUT	*/ \
+					  SCCR_DFSYNC00 	| 	/* SYNCLK / 1 (normal)	*/ \
+					  SCCR_DFBRG00		| 	/* BRGCLK / 1 (normal)	*/ \
+					  SCCR_DFNL000		| \
+					  SCCR_DFNH000		  \
+					)
+#else
+#define CFG_SCCR	( SCCR_TBS			| 	/* timebase = GCLK/2	*/ \
+					  SCCR_COM00   		| 	/* full strength CLKOUT	*/ \
+					  SCCR_DFSYNC00 	| 	/* SYNCLK / 1 (normal)	*/ \
+					  SCCR_DFBRG00		| 	/* BRGCLK / 1 (normal)	*/ \
+					  SCCR_DFNL000		| \
+					  SCCR_DFNH000		| \
+					  SCCR_RTDIV		| \
+					  SCCR_RTSEL		  \
+					)
+#endif
+
+/*-----------------------------------------------------------------------
+ * DER - Debug Enable Register									UM 37-46
+ *-----------------------------------------------------------------------
+ * Mask all events that can cause entry into debug mode
+ */
+#define CFG_DER				0
+
+/*
+ * Initialize Memory Controller:
+ *
+ * BR0 and OR0 (FLASH memory)
+ */
+#define FLASH_BASE0_PRELIM	FLASH_BASE
+
+/*
+ * Flash address mask
+ */
+#define CFG_PRELIM_OR_AM	0xfe000000
+
+/*
+ * FLASH timing:
+ * 33 Mhz bus with ACS = 11, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1
+ */
+#define CFG_OR_TIMING_FLASH	( OR_CSNT_SAM	| \
+							  OR_ACS_DIV2	| \
+							  OR_BI			| \
+							  OR_SCY_2_CLK	| \
+							  OR_TRLX		| \
+							  OR_EHTR		  \
+							)
+
+#define CFG_OR0_PRELIM	( CFG_PRELIM_OR_AM		| \
+						  CFG_OR_TIMING_FLASH	  \
+						)
+
+#define CFG_BR0_PRELIM	( (FLASH_BASE0_PRELIM & BR_BA_MSK)	| \
+						  BR_MS_GPCM						| \
+						  BR_PS_8							| \
+						  BR_V 								  \
+						)
+
+/*
+ * SDRAM configuration
+ */
+#define CFG_OR1_AM	0xfc000000
+#define CFG_OR1		( (CFG_OR1_AM & OR_AM_MSK)	| \
+					  OR_CSNT_SAM				  \
+					)
+
+#define CFG_BR1		( (SDRAM_BASE & BR_BA_MSK)	| \
+					  BR_MS_UPMA 				| \
+					  BR_PS_32	 				| \
+					  BR_V 						  \
+					)
+
+/*
+ * Refresh rate 7.8 us (= 64 ms / 8K = 31.2 uS quad bursts) for one bank
+ * of 256 MBit SDRAM
+ */
+#define CFG_MPTPR_1BK_8K	MPTPR_PTP_DIV16
+
+/*
+ * Periodic timer for refresh @ 33 MHz system clock
+ */
+#define CFG_MAMR_PTA	64
+
+/*
+ * MAMR settings for SDRAM
+ */
+#define CFG_MAMR_8COL	( (CFG_MAMR_PTA << MAMR_PTA_SHIFT)	| \
+						  MAMR_PTAE	    			| \
+						  MAMR_AMA_TYPE_1			| \
+						  MAMR_DSA_1_CYCL 			| \
+						  MAMR_G0CLA_A10			| \
+						  MAMR_RLFA_1X				| \
+						  MAMR_WLFA_1X				| \
+						  MAMR_TLFA_4X				  \
+						)
+
+/*
+ * CS2* configuration for Disk On Chip:
+ * 33 MHz bus with TRLX=1, ACS=11, CSNT=1, EBDF=1, SCY=2, EHTR=1,
+ * no burst.
+ */
+#define CFG_OR2_PRELIM 	( (0xffff0000 & OR_AM_MSK)	| \
+						  OR_CSNT_SAM				| \
+						  OR_ACS_DIV2				| \
+						  OR_BI						| \
+						  OR_SCY_2_CLK				| \
+						  OR_TRLX					| \
+						  OR_EHTR					  \
+						)
+
+#define CFG_BR2_PRELIM	( (DOC_BASE & BR_BA_MSK)	| \
+						  BR_PS_8					| \
+						  BR_MS_GPCM				| \
+						  BR_V						  \
+						)
+
+/*
+ * CS3* configuration for FPGA:
+ * 33 MHz bus with SCY=15, no burst.
+ * The FPGA uses TA and TEA to terminate bus cycles, but we
+ * clear SETA and set the cycle length to a large number so that
+ * the cycle will still complete even if there is a configuration
+ * error that prevents TA from asserting on FPGA accesss.
+ */
+#define CFG_OR3_PRELIM	( (0xfc000000 & OR_AM_MSK)  | \
+						  OR_SCY_15_CLK				| \
+						  OR_BI 					  \
+						)
+
+#define CFG_BR3_PRELIM	( (FPGA_BASE & BR_BA_MSK)	| \
+						  BR_PS_32					| \
+						  BR_MS_GPCM				| \
+						  BR_V		  				  \
+						)
+/*
+ * CS4* configuration for FPGA SelectMap configuration interface.
+ * 33 MHz bus, UPMB, no burst. Do not assert GPLB5 on falling edge
+ * of GCLK1_50
+ */
+#define CFG_OR4_PRELIM	( (0xffff0000 & OR_AM_MSK)  	| \
+						  OR_G5LS						| \
+						  OR_BI							  \
+						)
+
+#define CFG_BR4_PRELIM	( (SELECTMAP_BASE & BR_BA_MSK)	| \
+						  BR_PS_8						| \
+						  BR_MS_UPMB					| \
+						  BR_V			  				  \
+						)
+
+/*
+ * CS5* configuration for Mil-Std 1553 databus interface.
+ * 33 MHz bus, GPCM, no burst.
+ * The 1553 interface  uses TA and TEA to terminate bus cycles,
+ * but we clear SETA and set the cycle length to a large number so that
+ * the cycle will still complete even if there is a configuration
+ * error that prevents TA from asserting on FPGA accesss.
+ */
+#define CFG_OR5_PRELIM	( (0xffff0000 & OR_AM_MSK)  | \
+						  OR_SCY_15_CLK				| \
+						  OR_EHTR					| \
+						  OR_TRLX					| \
+						  OR_CSNT_SAM				| \
+						  OR_BI						  \
+						)
+
+#define CFG_BR5_PRELIM	( (M1553_BASE & BR_BA_MSK)	| \
+						  BR_PS_16					| \
+						  BR_MS_GPCM				| \
+						  BR_V			  			  \
+						)
+
+/*
+ * Boot Flags
+ */
+#define	BOOTFLAG_COLD	0x01	/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02	/* Software reboot					*/
+
+/*
+ * Disk On Chip (millenium) configuration
+ */
+#if !defined(CONFIG_SC)
+#define CFG_MAX_DOC_DEVICE	1
+#undef	CFG_DOC_SUPPORT_2000
+#define CFG_DOC_SUPPORT_MILLENNIUM
+#undef	CFG_DOC_PASSIVE_PROBE
+#endif
+
+/*
+ * FEC interrupt assignment
+ */
+#define FEC_INTERRUPT   SIU_LEVEL1
+
+/*
+ * Sanity checks
+ */
+#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET)
+#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured
+#endif
+
+#endif	/* __CONFIG_GEN860T_H */
+
+/* vim: set ts=4 tw=78 ai shiftwidth=4: */