diff options
Diffstat (limited to 'include/linux/com20020.h')
| -rw-r--r-- | include/linux/com20020.h | 116 |
1 files changed, 116 insertions, 0 deletions
diff --git a/include/linux/com20020.h b/include/linux/com20020.h new file mode 100644 index 00000000..5dcfb944 --- /dev/null +++ b/include/linux/com20020.h @@ -0,0 +1,116 @@ +/* + * Linux ARCnet driver - COM20020 chipset support - function declarations + * + * Written 1997 by David Woodhouse. + * Written 1994-1999 by Avery Pennarun. + * Derived from skeleton.c by Donald Becker. + * + * Special thanks to Contemporary Controls, Inc. (www.ccontrols.com) + * for sponsoring the further development of this driver. + * + * ********************** + * + * The original copyright of skeleton.c was as follows: + * + * skeleton.c Written 1993 by Donald Becker. + * Copyright 1993 United States Government as represented by the + * Director, National Security Agency. This software may only be used + * and distributed according to the terms of the GNU General Public License as + * modified by SRC, incorporated herein by reference. + * + * ********************** + * + * For more details, see drivers/net/arcnet.c + * + * ********************** + */ +#ifndef __COM20020_H +#define __COM20020_H + +int com20020_check(struct net_device *dev); +int com20020_found(struct net_device *dev, int shared); +extern const struct net_device_ops com20020_netdev_ops; + +/* The number of low I/O ports used by the card. */ +#define ARCNET_TOTAL_SIZE 8 + +/* various register addresses */ +#ifdef CONFIG_SA1100_CT6001 +#define BUS_ALIGN 2 /* 8 bit device on a 16 bit bus - needs padding */ +#else +#define BUS_ALIGN 1 +#endif + + +#define _INTMASK (ioaddr+BUS_ALIGN*0) /* writable */ +#define _STATUS (ioaddr+BUS_ALIGN*0) /* readable */ +#define _COMMAND (ioaddr+BUS_ALIGN*1) /* standard arcnet commands */ +#define _DIAGSTAT (ioaddr+BUS_ALIGN*1) /* diagnostic status register */ +#define _ADDR_HI (ioaddr+BUS_ALIGN*2) /* control registers for IO-mapped memory */ +#define _ADDR_LO (ioaddr+BUS_ALIGN*3) +#define _MEMDATA (ioaddr+BUS_ALIGN*4) /* data port for IO-mapped memory */ +#define _SUBADR (ioaddr+BUS_ALIGN*5) /* the extended port _XREG refers to */ +#define _CONFIG (ioaddr+BUS_ALIGN*6) /* configuration register */ +#define _XREG (ioaddr+BUS_ALIGN*7) /* extra registers (indexed by _CONFIG + or _SUBADR) */ + +/* in the ADDR_HI register */ +#define RDDATAflag 0x80 /* next access is a read (not a write) */ + +/* in the DIAGSTAT register */ +#define NEWNXTIDflag 0x02 /* ID to which token is passed has changed */ + +/* in the CONFIG register */ +#define RESETcfg 0x80 /* put card in reset state */ +#define TXENcfg 0x20 /* enable TX */ + +/* in SETUP register */ +#define PROMISCset 0x10 /* enable RCV_ALL */ +#define P1MODE 0x80 /* enable P1-MODE for Backplane */ +#define SLOWARB 0x01 /* enable Slow Arbitration for >=5Mbps */ + +/* COM2002x */ +#define SUB_TENTATIVE 0 /* tentative node ID */ +#define SUB_NODE 1 /* node ID */ +#define SUB_SETUP1 2 /* various options */ +#define SUB_TEST 3 /* test/diag register */ + +/* COM20022 only */ +#define SUB_SETUP2 4 /* sundry options */ +#define SUB_BUSCTL 5 /* bus control options */ +#define SUB_DMACOUNT 6 /* DMA count options */ + +#define SET_SUBADR(x) do { \ + if ((x) < 4) \ + { \ + lp->config = (lp->config & ~0x03) | (x); \ + SETCONF; \ + } \ + else \ + { \ + outb(x, _SUBADR); \ + } \ +} while (0) + +#undef ARCRESET +#undef ASTATUS +#undef ACOMMAND +#undef AINTMASK + +#define ARCRESET { outb(lp->config | 0x80, _CONFIG); \ + udelay(5); \ + outb(lp->config , _CONFIG); \ + } +#define ARCRESET0 { outb(0x18 | 0x80, _CONFIG); \ + udelay(5); \ + outb(0x18 , _CONFIG); \ + } + +#define ASTATUS() inb(_STATUS) +#define ADIAGSTATUS() inb(_DIAGSTAT) +#define ACOMMAND(cmd) outb((cmd),_COMMAND) +#define AINTMASK(msk) outb((msk),_INTMASK) + +#define SETCONF outb(lp->config, _CONFIG) + +#endif /* __COM20020_H */ |