diff options
Diffstat (limited to 'arch/arm/mach-at91/board-sam9g20ek.c')
| -rw-r--r-- | arch/arm/mach-at91/board-sam9g20ek.c | 418 |
1 files changed, 418 insertions, 0 deletions
diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c new file mode 100644 index 00000000..8923ec9f --- /dev/null +++ b/arch/arm/mach-at91/board-sam9g20ek.c @@ -0,0 +1,418 @@ +/* + * Copyright (C) 2005 SAN People + * Copyright (C) 2008 Atmel + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <linux/types.h> +#include <linux/gpio.h> +#include <linux/init.h> +#include <linux/mm.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/spi/spi.h> +#include <linux/spi/at73c213.h> +#include <linux/gpio_keys.h> +#include <linux/input.h> +#include <linux/clk.h> +#include <linux/regulator/machine.h> +#include <linux/regulator/fixed.h> +#include <linux/regulator/consumer.h> + +#include <mach/hardware.h> +#include <asm/setup.h> +#include <asm/mach-types.h> +#include <asm/irq.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <mach/board.h> +#include <mach/at91sam9_smc.h> +#include <mach/system_rev.h> + +#include "sam9_smc.h" +#include "generic.h" + +/* + * board revision encoding + * bit 0: + * 0 => 1 sd/mmc slot + * 1 => 2 sd/mmc slots connectors (board from revision C) + */ +#define HAVE_2MMC (1 << 0) +static int inline ek_have_2mmc(void) +{ + return machine_is_at91sam9g20ek_2mmc() || (system_rev & HAVE_2MMC); +} + + +static void __init ek_init_early(void) +{ + /* Initialize processor: 18.432 MHz crystal */ + at91_initialize(18432000); + + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); + + /* set serial console to ttyS0 (ie, DBGU) */ + at91_set_serial_console(0); +} + +/* + * USB Host port + */ +static struct at91_usbh_data __initdata ek_usbh_data = { + .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, +}; + +/* + * USB Device port + */ +static struct at91_udc_data __initdata ek_udc_data = { + .vbus_pin = AT91_PIN_PC5, + .pullup_pin = -EINVAL, /* pull-up driven by UDC */ +}; + + +/* + * SPI devices. + */ +static struct spi_board_info ek_spi_devices[] = { +#if !(defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_AT91)) + { /* DataFlash chip */ + .modalias = "mtd_dataflash", + .chip_select = 1, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + }, +#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD) + { /* DataFlash card */ + .modalias = "mtd_dataflash", + .chip_select = 0, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + }, +#endif +#endif +}; + + +/* + * MACB Ethernet device + */ +static struct macb_platform_data __initdata ek_macb_data = { + .phy_irq_pin = AT91_PIN_PA7, + .is_rmii = 1, +}; + +static void __init ek_add_device_macb(void) +{ + if (ek_have_2mmc()) + ek_macb_data.phy_irq_pin = AT91_PIN_PB0; + + at91_add_device_eth(&ek_macb_data); +} + +/* + * NAND flash + */ +static struct mtd_partition __initdata ek_nand_partition[] = { + { + .name = "Bootstrap", + .offset = 0, + .size = 4 * SZ_1M, + }, + { + .name = "Partition 1", + .offset = MTDPART_OFS_NXTBLK, + .size = 60 * SZ_1M, + }, + { + .name = "Partition 2", + .offset = MTDPART_OFS_NXTBLK, + .size = MTDPART_SIZ_FULL, + }, +}; + +/* det_pin is not connected */ +static struct atmel_nand_data __initdata ek_nand_data = { + .ale = 21, + .cle = 22, + .rdy_pin = AT91_PIN_PC13, + .enable_pin = AT91_PIN_PC14, + .det_pin = -EINVAL, + .ecc_mode = NAND_ECC_SOFT, + .on_flash_bbt = 1, + .parts = ek_nand_partition, + .num_parts = ARRAY_SIZE(ek_nand_partition), +}; + +static struct sam9_smc_config __initdata ek_nand_smc_config = { + .ncs_read_setup = 0, + .nrd_setup = 2, + .ncs_write_setup = 0, + .nwe_setup = 2, + + .ncs_read_pulse = 4, + .nrd_pulse = 4, + .ncs_write_pulse = 4, + .nwe_pulse = 4, + + .read_cycle = 7, + .write_cycle = 7, + + .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE, + .tdf_cycles = 3, +}; + +static void __init ek_add_device_nand(void) +{ + ek_nand_data.bus_width_16 = board_have_nand_16bit(); + /* setup bus-width (8 or 16) */ + if (ek_nand_data.bus_width_16) + ek_nand_smc_config.mode |= AT91_SMC_DBW_16; + else + ek_nand_smc_config.mode |= AT91_SMC_DBW_8; + + /* configure chip-select 3 (NAND) */ + sam9_smc_configure(0, 3, &ek_nand_smc_config); + + at91_add_device_nand(&ek_nand_data); +} + + +/* + * MCI (SD/MMC) + * wp_pin and vcc_pin are not connected + */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata ek_mmc_data = { + .slot[1] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PC9, + .wp_pin = -EINVAL, + }, + +}; +#else +static struct at91_mmc_data __initdata ek_mmc_data = { + .slot_b = 1, /* Only one slot so use slot B */ + .wire4 = 1, + .det_pin = AT91_PIN_PC9, + .wp_pin = -EINVAL, + .vcc_pin = -EINVAL, +}; +#endif + +static void __init ek_add_device_mmc(void) +{ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + if (ek_have_2mmc()) { + ek_mmc_data.slot[0].bus_width = 4; + ek_mmc_data.slot[0].detect_pin = AT91_PIN_PC2; + ek_mmc_data.slot[0].wp_pin = -1; + } + at91_add_device_mci(0, &ek_mmc_data); +#else + at91_add_device_mmc(0, &ek_mmc_data); +#endif +} + +/* + * LEDs + */ +static struct gpio_led ek_leds[] = { + { /* "bottom" led, green, userled1 to be defined */ + .name = "ds5", + .gpio = AT91_PIN_PA6, + .active_low = 1, + .default_trigger = "none", + }, + { /* "power" led, yellow */ + .name = "ds1", + .gpio = AT91_PIN_PA9, + .default_trigger = "heartbeat", + } +}; + +static void __init ek_add_device_gpio_leds(void) +{ + if (ek_have_2mmc()) { + ek_leds[0].gpio = AT91_PIN_PB8; + ek_leds[1].gpio = AT91_PIN_PB9; + } + + at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); +} + +/* + * GPIO Buttons + */ +#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) +static struct gpio_keys_button ek_buttons[] = { + { + .gpio = AT91_PIN_PA30, + .code = BTN_3, + .desc = "Button 3", + .active_low = 1, + .wakeup = 1, + }, + { + .gpio = AT91_PIN_PA31, + .code = BTN_4, + .desc = "Button 4", + .active_low = 1, + .wakeup = 1, + } +}; + +static struct gpio_keys_platform_data ek_button_data = { + .buttons = ek_buttons, + .nbuttons = ARRAY_SIZE(ek_buttons), +}; + +static struct platform_device ek_button_device = { + .name = "gpio-keys", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &ek_button_data, + } +}; + +static void __init ek_add_device_buttons(void) +{ + at91_set_gpio_input(AT91_PIN_PA30, 1); /* btn3 */ + at91_set_deglitch(AT91_PIN_PA30, 1); + at91_set_gpio_input(AT91_PIN_PA31, 1); /* btn4 */ + at91_set_deglitch(AT91_PIN_PA31, 1); + + platform_device_register(&ek_button_device); +} +#else +static void __init ek_add_device_buttons(void) {} +#endif + +#if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE) +static struct regulator_consumer_supply ek_audio_consumer_supplies[] = { + REGULATOR_SUPPLY("AVDD", "0-001b"), + REGULATOR_SUPPLY("HPVDD", "0-001b"), + REGULATOR_SUPPLY("DBVDD", "0-001b"), + REGULATOR_SUPPLY("DCVDD", "0-001b"), +}; + +static struct regulator_init_data ek_avdd_reg_init_data = { + .constraints = { + .name = "3V3", + .valid_ops_mask = REGULATOR_CHANGE_STATUS, + }, + .consumer_supplies = ek_audio_consumer_supplies, + .num_consumer_supplies = ARRAY_SIZE(ek_audio_consumer_supplies), +}; + +static struct fixed_voltage_config ek_vdd_pdata = { + .supply_name = "board-3V3", + .microvolts = 3300000, + .gpio = -EINVAL, + .enabled_at_boot = 0, + .init_data = &ek_avdd_reg_init_data, +}; +static struct platform_device ek_voltage_regulator = { + .name = "reg-fixed-voltage", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &ek_vdd_pdata, + }, +}; +static void __init ek_add_regulators(void) +{ + platform_device_register(&ek_voltage_regulator); +} +#else +static void __init ek_add_regulators(void) {} +#endif + + +static struct i2c_board_info __initdata ek_i2c_devices[] = { + { + I2C_BOARD_INFO("24c512", 0x50) + }, + { + I2C_BOARD_INFO("wm8731", 0x1b) + }, +}; + + +static void __init ek_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* USB Host */ + at91_add_device_usbh(&ek_usbh_data); + /* USB Device */ + at91_add_device_udc(&ek_udc_data); + /* SPI */ + at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); + /* NAND */ + ek_add_device_nand(); + /* Ethernet */ + ek_add_device_macb(); + /* Regulators */ + ek_add_regulators(); + /* MMC */ + ek_add_device_mmc(); + /* I2C */ + at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices)); + /* LEDs */ + ek_add_device_gpio_leds(); + /* Push Buttons */ + ek_add_device_buttons(); + /* PCK0 provides MCLK to the WM8731 */ + at91_set_B_periph(AT91_PIN_PC1, 0); + /* SSC (for WM8731) */ + at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX); +} + +MACHINE_START(AT91SAM9G20EK, "Atmel AT91SAM9G20-EK") + /* Maintainer: Atmel */ + .timer = &at91sam926x_timer, + .map_io = at91_map_io, + .init_early = ek_init_early, + .init_irq = at91_init_irq_default, + .init_machine = ek_board_init, +MACHINE_END + +MACHINE_START(AT91SAM9G20EK_2MMC, "Atmel AT91SAM9G20-EK 2 MMC Slot Mod") + /* Maintainer: Atmel */ + .timer = &at91sam926x_timer, + .map_io = at91_map_io, + .init_early = ek_init_early, + .init_irq = at91_init_irq_default, + .init_machine = ek_board_init, +MACHINE_END |