diff options
Diffstat (limited to 'arch/arm/mach-at91/board-sam9260ek.c')
| -rw-r--r-- | arch/arm/mach-at91/board-sam9260ek.c | 354 |
1 files changed, 354 insertions, 0 deletions
diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c new file mode 100644 index 00000000..d5aec55b --- /dev/null +++ b/arch/arm/mach-at91/board-sam9260ek.c @@ -0,0 +1,354 @@ +/* + * linux/arch/arm/mach-at91/board-sam9260ek.c + * + * Copyright (C) 2005 SAN People + * Copyright (C) 2006 Atmel + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <linux/types.h> +#include <linux/gpio.h> +#include <linux/init.h> +#include <linux/mm.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/spi/spi.h> +#include <linux/spi/at73c213.h> +#include <linux/clk.h> +#include <linux/i2c/at24.h> +#include <linux/gpio_keys.h> +#include <linux/input.h> + +#include <asm/setup.h> +#include <asm/mach-types.h> +#include <asm/irq.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <mach/hardware.h> +#include <mach/board.h> +#include <mach/at91sam9_smc.h> +#include <mach/at91_shdwc.h> +#include <mach/system_rev.h> + +#include "sam9_smc.h" +#include "generic.h" + + +static void __init ek_init_early(void) +{ + /* Initialize processor: 18.432 MHz crystal */ + at91_initialize(18432000); + + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); + + /* set serial console to ttyS0 (ie, DBGU) */ + at91_set_serial_console(0); +} + +/* + * USB Host port + */ +static struct at91_usbh_data __initdata ek_usbh_data = { + .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, +}; + +/* + * USB Device port + */ +static struct at91_udc_data __initdata ek_udc_data = { + .vbus_pin = AT91_PIN_PC5, + .pullup_pin = -EINVAL, /* pull-up driven by UDC */ +}; + + +/* + * Audio + */ +static struct at73c213_board_info at73c213_data = { + .ssc_id = 0, + .shortname = "AT91SAM9260-EK external DAC", +}; + +#if defined(CONFIG_SND_AT73C213) || defined(CONFIG_SND_AT73C213_MODULE) +static void __init at73c213_set_clk(struct at73c213_board_info *info) +{ + struct clk *pck0; + struct clk *plla; + + pck0 = clk_get(NULL, "pck0"); + plla = clk_get(NULL, "plla"); + + /* AT73C213 MCK Clock */ + at91_set_B_periph(AT91_PIN_PC1, 0); /* PCK0 */ + + clk_set_parent(pck0, plla); + clk_put(plla); + + info->dac_clk = pck0; +} +#else +static void __init at73c213_set_clk(struct at73c213_board_info *info) {} +#endif + +/* + * SPI devices. + */ +static struct spi_board_info ek_spi_devices[] = { +#if !defined(CONFIG_MMC_AT91) + { /* DataFlash chip */ + .modalias = "mtd_dataflash", + .chip_select = 1, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + }, +#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD) + { /* DataFlash card */ + .modalias = "mtd_dataflash", + .chip_select = 0, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + }, +#endif +#endif +#if defined(CONFIG_SND_AT73C213) || defined(CONFIG_SND_AT73C213_MODULE) + { /* AT73C213 DAC */ + .modalias = "at73c213", + .chip_select = 0, + .max_speed_hz = 10 * 1000 * 1000, + .bus_num = 1, + .mode = SPI_MODE_1, + .platform_data = &at73c213_data, + }, +#endif +}; + + +/* + * MACB Ethernet device + */ +static struct macb_platform_data __initdata ek_macb_data = { + .phy_irq_pin = AT91_PIN_PA7, + .is_rmii = 1, +}; + + +/* + * NAND flash + */ +static struct mtd_partition __initdata ek_nand_partition[] = { + { + .name = "Partition 1", + .offset = 0, + .size = SZ_256K, + }, + { + .name = "Partition 2", + .offset = MTDPART_OFS_NXTBLK, + .size = MTDPART_SIZ_FULL, + }, +}; + +static struct atmel_nand_data __initdata ek_nand_data = { + .ale = 21, + .cle = 22, + .det_pin = -EINVAL, + .rdy_pin = AT91_PIN_PC13, + .enable_pin = AT91_PIN_PC14, + .ecc_mode = NAND_ECC_SOFT, + .on_flash_bbt = 1, + .parts = ek_nand_partition, + .num_parts = ARRAY_SIZE(ek_nand_partition), +}; + +static struct sam9_smc_config __initdata ek_nand_smc_config = { + .ncs_read_setup = 0, + .nrd_setup = 1, + .ncs_write_setup = 0, + .nwe_setup = 1, + + .ncs_read_pulse = 3, + .nrd_pulse = 3, + .ncs_write_pulse = 3, + .nwe_pulse = 3, + + .read_cycle = 5, + .write_cycle = 5, + + .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE, + .tdf_cycles = 2, +}; + +static void __init ek_add_device_nand(void) +{ + ek_nand_data.bus_width_16 = board_have_nand_16bit(); + /* setup bus-width (8 or 16) */ + if (ek_nand_data.bus_width_16) + ek_nand_smc_config.mode |= AT91_SMC_DBW_16; + else + ek_nand_smc_config.mode |= AT91_SMC_DBW_8; + + /* configure chip-select 3 (NAND) */ + sam9_smc_configure(0, 3, &ek_nand_smc_config); + + at91_add_device_nand(&ek_nand_data); +} + + +/* + * MCI (SD/MMC) + */ +static struct at91_mmc_data __initdata ek_mmc_data = { + .slot_b = 1, + .wire4 = 1, + .det_pin = -EINVAL, + .wp_pin = -EINVAL, + .vcc_pin = -EINVAL, +}; + + +/* + * LEDs + */ +static struct gpio_led ek_leds[] = { + { /* "bottom" led, green, userled1 to be defined */ + .name = "ds5", + .gpio = AT91_PIN_PA6, + .active_low = 1, + .default_trigger = "none", + }, + { /* "power" led, yellow */ + .name = "ds1", + .gpio = AT91_PIN_PA9, + .default_trigger = "heartbeat", + } +}; + +/* + * I2C devices + */ +static struct at24_platform_data at24c512 = { + .byte_len = SZ_512K / 8, + .page_size = 128, + .flags = AT24_FLAG_ADDR16, +}; + +static struct i2c_board_info __initdata ek_i2c_devices[] = { + { + I2C_BOARD_INFO("24c512", 0x50), + .platform_data = &at24c512, + }, + /* more devices can be added using expansion connectors */ +}; + + +/* + * GPIO Buttons + */ +#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) +static struct gpio_keys_button ek_buttons[] = { + { + .gpio = AT91_PIN_PA30, + .code = BTN_3, + .desc = "Button 3", + .active_low = 1, + .wakeup = 1, + }, + { + .gpio = AT91_PIN_PA31, + .code = BTN_4, + .desc = "Button 4", + .active_low = 1, + .wakeup = 1, + } +}; + +static struct gpio_keys_platform_data ek_button_data = { + .buttons = ek_buttons, + .nbuttons = ARRAY_SIZE(ek_buttons), +}; + +static struct platform_device ek_button_device = { + .name = "gpio-keys", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &ek_button_data, + } +}; + +static void __init ek_add_device_buttons(void) +{ + at91_set_gpio_input(AT91_PIN_PA30, 1); /* btn3 */ + at91_set_deglitch(AT91_PIN_PA30, 1); + at91_set_gpio_input(AT91_PIN_PA31, 1); /* btn4 */ + at91_set_deglitch(AT91_PIN_PA31, 1); + + platform_device_register(&ek_button_device); +} +#else +static void __init ek_add_device_buttons(void) {} +#endif + + +static void __init ek_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* USB Host */ + at91_add_device_usbh(&ek_usbh_data); + /* USB Device */ + at91_add_device_udc(&ek_udc_data); + /* SPI */ + at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); + /* NAND */ + ek_add_device_nand(); + /* Ethernet */ + at91_add_device_eth(&ek_macb_data); + /* MMC */ + at91_add_device_mmc(0, &ek_mmc_data); + /* I2C */ + at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices)); + /* SSC (to AT73C213) */ + at73c213_set_clk(&at73c213_data); + at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX); + /* LEDs */ + at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); + /* Push Buttons */ + ek_add_device_buttons(); +} + +MACHINE_START(AT91SAM9260EK, "Atmel AT91SAM9260-EK") + /* Maintainer: Atmel */ + .timer = &at91sam926x_timer, + .map_io = at91_map_io, + .init_early = ek_init_early, + .init_irq = at91_init_irq_default, + .init_machine = ek_board_init, +MACHINE_END |