diff options
Diffstat (limited to 'Documentation/networking/README.ipw2100')
| -rw-r--r-- | Documentation/networking/README.ipw2100 | 293 |
1 files changed, 293 insertions, 0 deletions
diff --git a/Documentation/networking/README.ipw2100 b/Documentation/networking/README.ipw2100 new file mode 100644 index 00000000..6f85e1d0 --- /dev/null +++ b/Documentation/networking/README.ipw2100 @@ -0,0 +1,293 @@ + +Intel(R) PRO/Wireless 2100 Driver for Linux in support of: + +Intel(R) PRO/Wireless 2100 Network Connection + +Copyright (C) 2003-2006, Intel Corporation + +README.ipw2100 + +Version: git-1.1.5 +Date : January 25, 2006 + +Index +----------------------------------------------- +0. IMPORTANT INFORMATION BEFORE USING THIS DRIVER +1. Introduction +2. Release git-1.1.5 Current Features +3. Command Line Parameters +4. Sysfs Helper Files +5. Radio Kill Switch +6. Dynamic Firmware +7. Power Management +8. Support +9. License + + +0. IMPORTANT INFORMATION BEFORE USING THIS DRIVER +----------------------------------------------- + +Important Notice FOR ALL USERS OR DISTRIBUTORS!!!! + +Intel wireless LAN adapters are engineered, manufactured, tested, and +quality checked to ensure that they meet all necessary local and +governmental regulatory agency requirements for the regions that they +are designated and/or marked to ship into. Since wireless LANs are +generally unlicensed devices that share spectrum with radars, +satellites, and other licensed and unlicensed devices, it is sometimes +necessary to dynamically detect, avoid, and limit usage to avoid +interference with these devices. In many instances Intel is required to +provide test data to prove regional and local compliance to regional and +governmental regulations before certification or approval to use the +product is granted. Intel's wireless LAN's EEPROM, firmware, and +software driver are designed to carefully control parameters that affect +radio operation and to ensure electromagnetic compliance (EMC). These +parameters include, without limitation, RF power, spectrum usage, +channel scanning, and human exposure. + +For these reasons Intel cannot permit any manipulation by third parties +of the software provided in binary format with the wireless WLAN +adapters (e.g., the EEPROM and firmware). Furthermore, if you use any +patches, utilities, or code with the Intel wireless LAN adapters that +have been manipulated by an unauthorized party (i.e., patches, +utilities, or code (including open source code modifications) which have +not been validated by Intel), (i) you will be solely responsible for +ensuring the regulatory compliance of the products, (ii) Intel will bear +no liability, under any theory of liability for any issues associated +with the modified products, including without limitation, claims under +the warranty and/or issues arising from regulatory non-compliance, and +(iii) Intel will not provide or be required to assist in providing +support to any third parties for such modified products. + +Note: Many regulatory agencies consider Wireless LAN adapters to be +modules, and accordingly, condition system-level regulatory approval +upon receipt and review of test data documenting that the antennas and +system configuration do not cause the EMC and radio operation to be +non-compliant. + +The drivers available for download from SourceForge are provided as a +part of a development project. Conformance to local regulatory +requirements is the responsibility of the individual developer. As +such, if you are interested in deploying or shipping a driver as part of +solution intended to be used for purposes other than development, please +obtain a tested driver from Intel Customer Support at: + +http://www.intel.com/support/wireless/sb/CS-006408.htm + +1. Introduction +----------------------------------------------- + +This document provides a brief overview of the features supported by the +IPW2100 driver project. The main project website, where the latest +development version of the driver can be found, is: + + http://ipw2100.sourceforge.net + +There you can find the not only the latest releases, but also information about +potential fixes and patches, as well as links to the development mailing list +for the driver project. + + +2. Release git-1.1.5 Current Supported Features +----------------------------------------------- +- Managed (BSS) and Ad-Hoc (IBSS) +- WEP (shared key and open) +- Wireless Tools support +- 802.1x (tested with XSupplicant 1.0.1) + +Enabled (but not supported) features: +- Monitor/RFMon mode +- WPA/WPA2 + +The distinction between officially supported and enabled is a reflection +on the amount of validation and interoperability testing that has been +performed on a given feature. + + +3. Command Line Parameters +----------------------------------------------- + +If the driver is built as a module, the following optional parameters are used +by entering them on the command line with the modprobe command using this +syntax: + + modprobe ipw2100 [<option>=<VAL1><,VAL2>...] + +For example, to disable the radio on driver loading, enter: + + modprobe ipw2100 disable=1 + +The ipw2100 driver supports the following module parameters: + +Name Value Example: +debug 0x0-0xffffffff debug=1024 +mode 0,1,2 mode=1 /* AdHoc */ +channel int channel=3 /* Only valid in AdHoc or Monitor */ +associate boolean associate=0 /* Do NOT auto associate */ +disable boolean disable=1 /* Do not power the HW */ + + +4. Sysfs Helper Files +--------------------------- +----------------------------------------------- + +There are several ways to control the behavior of the driver. Many of the +general capabilities are exposed through the Wireless Tools (iwconfig). There +are a few capabilities that are exposed through entries in the Linux Sysfs. + + +----- Driver Level ------ +For the driver level files, look in /sys/bus/pci/drivers/ipw2100/ + + debug_level + + This controls the same global as the 'debug' module parameter. For + information on the various debugging levels available, run the 'dvals' + script found in the driver source directory. + + NOTE: 'debug_level' is only enabled if CONFIG_IPW2100_DEBUG is turn + on. + +----- Device Level ------ +For the device level files look in + + /sys/bus/pci/drivers/ipw2100/{PCI-ID}/ + +For example: + /sys/bus/pci/drivers/ipw2100/0000:02:01.0 + +For the device level files, see /sys/bus/pci/drivers/ipw2100: + + rf_kill + read - + 0 = RF kill not enabled (radio on) + 1 = SW based RF kill active (radio off) + 2 = HW based RF kill active (radio off) + 3 = Both HW and SW RF kill active (radio off) + write - + 0 = If SW based RF kill active, turn the radio back on + 1 = If radio is on, activate SW based RF kill + + NOTE: If you enable the SW based RF kill and then toggle the HW + based RF kill from ON -> OFF -> ON, the radio will NOT come back on + + +5. Radio Kill Switch +----------------------------------------------- +Most laptops provide the ability for the user to physically disable the radio. +Some vendors have implemented this as a physical switch that requires no +software to turn the radio off and on. On other laptops, however, the switch +is controlled through a button being pressed and a software driver then making +calls to turn the radio off and on. This is referred to as a "software based +RF kill switch" + +See the Sysfs helper file 'rf_kill' for determining the state of the RF switch +on your system. + + +6. Dynamic Firmware +----------------------------------------------- +As the firmware is licensed under a restricted use license, it can not be +included within the kernel sources. To enable the IPW2100 you will need a +firmware image to load into the wireless NIC's processors. + +You can obtain these images from <http://ipw2100.sf.net/firmware.php>. + +See INSTALL for instructions on installing the firmware. + + +7. Power Management +----------------------------------------------- +The IPW2100 supports the configuration of the Power Save Protocol +through a private wireless extension interface. The IPW2100 supports +the following different modes: + + off No power management. Radio is always on. + on Automatic power management + 1-5 Different levels of power management. The higher the + number the greater the power savings, but with an impact to + packet latencies. + +Power management works by powering down the radio after a certain +interval of time has passed where no packets are passed through the +radio. Once powered down, the radio remains in that state for a given +period of time. For higher power savings, the interval between last +packet processed to sleep is shorter and the sleep period is longer. + +When the radio is asleep, the access point sending data to the station +must buffer packets at the AP until the station wakes up and requests +any buffered packets. If you have an AP that does not correctly support +the PSP protocol you may experience packet loss or very poor performance +while power management is enabled. If this is the case, you will need +to try and find a firmware update for your AP, or disable power +management (via `iwconfig eth1 power off`) + +To configure the power level on the IPW2100 you use a combination of +iwconfig and iwpriv. iwconfig is used to turn power management on, off, +and set it to auto. + + iwconfig eth1 power off Disables radio power down + iwconfig eth1 power on Enables radio power management to + last set level (defaults to AUTO) + iwpriv eth1 set_power 0 Sets power level to AUTO and enables + power management if not previously + enabled. + iwpriv eth1 set_power 1-5 Set the power level as specified, + enabling power management if not + previously enabled. + +You can view the current power level setting via: + + iwpriv eth1 get_power + +It will return the current period or timeout that is configured as a string +in the form of xxxx/yyyy (z) where xxxx is the timeout interval (amount of +time after packet processing), yyyy is the period to sleep (amount of time to +wait before powering the radio and querying the access point for buffered +packets), and z is the 'power level'. If power management is turned off the +xxxx/yyyy will be replaced with 'off' -- the level reported will be the active +level if `iwconfig eth1 power on` is invoked. + + +8. Support +----------------------------------------------- + +For general development information and support, +go to: + + http://ipw2100.sf.net/ + +The ipw2100 1.1.0 driver and firmware can be downloaded from: + + http://support.intel.com + +For installation support on the ipw2100 1.1.0 driver on Linux kernels +2.6.8 or greater, email support is available from: + + http://supportmail.intel.com + +9. License +----------------------------------------------- + + Copyright(c) 2003 - 2006 Intel Corporation. All rights reserved. + + This program is free software; you can redistribute it and/or modify it + under the terms of the GNU General Public License (version 2) as + published by the Free Software Foundation. + + This program is distributed in the hope that it will be useful, but WITHOUT + ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + more details. + + You should have received a copy of the GNU General Public License along with + this program; if not, write to the Free Software Foundation, Inc., 59 + Temple Place - Suite 330, Boston, MA 02111-1307, USA. + + The full GNU General Public License is included in this distribution in the + file called LICENSE. + + License Contact Information: + James P. Ketrenos <ipw2100-admin@linux.intel.com> + Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + |