diff options
Diffstat (limited to 'Documentation/devicetree/bindings/regulator')
4 files changed, 180 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/regulator/anatop-regulator.txt b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt new file mode 100644 index 00000000..357758cb --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt @@ -0,0 +1,29 @@ +Anatop Voltage regulators + +Required properties: +- compatible: Must be "fsl,anatop-regulator" +- anatop-reg-offset: Anatop MFD register offset +- anatop-vol-bit-shift: Bit shift for the register +- anatop-vol-bit-width: Number of bits used in the register +- anatop-min-bit-val: Minimum value of this register +- anatop-min-voltage: Minimum voltage of this regulator +- anatop-max-voltage: Maximum voltage of this regulator + +Any property defined as part of the core regulator +binding, defined in regulator.txt, can also be used. + +Example: + + regulator-vddpu { + compatible = "fsl,anatop-regulator"; + regulator-name = "vddpu"; + regulator-min-microvolt = <725000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + anatop-reg-offset = <0x140>; + anatop-vol-bit-shift = <9>; + anatop-vol-bit-width = <5>; + anatop-min-bit-val = <1>; + anatop-min-voltage = <725000>; + anatop-max-voltage = <1300000>; + }; diff --git a/Documentation/devicetree/bindings/regulator/fixed-regulator.txt b/Documentation/devicetree/bindings/regulator/fixed-regulator.txt new file mode 100644 index 00000000..9cf57fd0 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/fixed-regulator.txt @@ -0,0 +1,29 @@ +Fixed Voltage regulators + +Required properties: +- compatible: Must be "regulator-fixed"; + +Optional properties: +- gpio: gpio to use for enable control +- startup-delay-us: startup time in microseconds +- enable-active-high: Polarity of GPIO is Active high +If this property is missing, the default assumed is Active low. + +Any property defined as part of the core regulator +binding, defined in regulator.txt, can also be used. +However a fixed voltage regulator is expected to have the +regulator-min-microvolt and regulator-max-microvolt +to be the same. + +Example: + + abc: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "fixed-supply"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio1 16 0>; + startup-delay-us = <70000>; + enable-active-high; + regulator-boot-on + }; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt new file mode 100644 index 00000000..5b7a408a --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -0,0 +1,54 @@ +Voltage/Current Regulators + +Optional properties: +- regulator-name: A string used as a descriptive name for regulator outputs +- regulator-min-microvolt: smallest voltage consumers may set +- regulator-max-microvolt: largest voltage consumers may set +- regulator-microvolt-offset: Offset applied to voltages to compensate for voltage drops +- regulator-min-microamp: smallest current consumers may set +- regulator-max-microamp: largest current consumers may set +- regulator-always-on: boolean, regulator should never be disabled +- regulator-boot-on: bootloader/firmware enabled regulator +- <name>-supply: phandle to the parent supply/regulator node + +Example: + + xyzreg: regulator@0 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + vin-supply = <&vin>; + }; + +Regulator Consumers: +Consumer nodes can reference one or more of its supplies/ +regulators using the below bindings. + +- <name>-supply: phandle to the regulator node + +These are the same bindings that a regulator in the above +example used to reference its own supply, in which case +its just seen as a special case of a regulator being a +consumer itself. + +Example of a consumer device node (mmc) referencing two +regulators (twl_reg1 and twl_reg2), + + twl_reg1: regulator@0 { + ... + ... + ... + }; + + twl_reg2: regulator@1 { + ... + ... + ... + }; + + mmc: mmc@0x0 { + ... + ... + vmmc-supply = <&twl_reg1>; + vmmcaux-supply = <&twl_reg2>; + }; diff --git a/Documentation/devicetree/bindings/regulator/twl-regulator.txt b/Documentation/devicetree/bindings/regulator/twl-regulator.txt new file mode 100644 index 00000000..0c3395d5 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/twl-regulator.txt @@ -0,0 +1,68 @@ +TWL family of regulators + +Required properties: +For twl6030 regulators/LDOs +- compatible: + - "ti,twl6030-vaux1" for VAUX1 LDO + - "ti,twl6030-vaux2" for VAUX2 LDO + - "ti,twl6030-vaux3" for VAUX3 LDO + - "ti,twl6030-vmmc" for VMMC LDO + - "ti,twl6030-vpp" for VPP LDO + - "ti,twl6030-vusim" for VUSIM LDO + - "ti,twl6030-vana" for VANA LDO + - "ti,twl6030-vcxio" for VCXIO LDO + - "ti,twl6030-vdac" for VDAC LDO + - "ti,twl6030-vusb" for VUSB LDO + - "ti,twl6030-v1v8" for V1V8 LDO + - "ti,twl6030-v2v1" for V2V1 LDO + - "ti,twl6030-clk32kg" for CLK32KG RESOURCE + - "ti,twl6030-vdd1" for VDD1 SMPS + - "ti,twl6030-vdd2" for VDD2 SMPS + - "ti,twl6030-vdd3" for VDD3 SMPS +For twl6025 regulators/LDOs +- compatible: + - "ti,twl6025-ldo1" for LDO1 LDO + - "ti,twl6025-ldo2" for LDO2 LDO + - "ti,twl6025-ldo3" for LDO3 LDO + - "ti,twl6025-ldo4" for LDO4 LDO + - "ti,twl6025-ldo5" for LDO5 LDO + - "ti,twl6025-ldo6" for LDO6 LDO + - "ti,twl6025-ldo7" for LDO7 LDO + - "ti,twl6025-ldoln" for LDOLN LDO + - "ti,twl6025-ldousb" for LDOUSB LDO + - "ti,twl6025-smps3" for SMPS3 SMPS + - "ti,twl6025-smps4" for SMPS4 SMPS + - "ti,twl6025-vio" for VIO SMPS +For twl4030 regulators/LDOs +- compatible: + - "ti,twl4030-vaux1" for VAUX1 LDO + - "ti,twl4030-vaux2" for VAUX2 LDO + - "ti,twl5030-vaux2" for VAUX2 LDO + - "ti,twl4030-vaux3" for VAUX3 LDO + - "ti,twl4030-vaux4" for VAUX4 LDO + - "ti,twl4030-vmmc1" for VMMC1 LDO + - "ti,twl4030-vmmc2" for VMMC2 LDO + - "ti,twl4030-vpll1" for VPLL1 LDO + - "ti,twl4030-vpll2" for VPLL2 LDO + - "ti,twl4030-vsim" for VSIM LDO + - "ti,twl4030-vdac" for VDAC LDO + - "ti,twl4030-vintana2" for VINTANA2 LDO + - "ti,twl4030-vio" for VIO LDO + - "ti,twl4030-vdd1" for VDD1 SMPS + - "ti,twl4030-vdd2" for VDD2 SMPS + - "ti,twl4030-vintana1" for VINTANA1 LDO + - "ti,twl4030-vintdig" for VINTDIG LDO + - "ti,twl4030-vusb1v5" for VUSB1V5 LDO + - "ti,twl4030-vusb1v8" for VUSB1V8 LDO + - "ti,twl4030-vusb3v1" for VUSB3V1 LDO + +Optional properties: +- Any optional property defined in bindings/regulator/regulator.txt + +Example: + + xyz: regulator@0 { + compatible = "ti,twl6030-vaux1"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + }; |