Moved, renamed, and deleted files

The original directory structure was scattered and unorganized.
Changes are basically to make it look like kernel structure.

1 files changed, 250 insertions, 0 deletions

diff --git a/drivers/ata/pata_mpiix.c b/drivers/ata/pata_mpiix.c
new file mode 100644
index 00000000..9dc16df8
--- /dev/null
+++ b/drivers/ata/pata_mpiix.c
@@ -0,0 +1,250 @@
+/*
+ * pata_mpiix.c 	- Intel MPIIX PATA for new ATA layer
+ *			  (C) 2005-2006 Red Hat Inc
+ *			  Alan Cox <alan@lxorguk.ukuu.org.uk>
+ *
+ * The MPIIX is different enough to the PIIX4 and friends that we give it
+ * a separate driver. The old ide/pci code handles this by just not tuning
+ * MPIIX at all.
+ *
+ * The MPIIX also differs in another important way from the majority of PIIX
+ * devices. The chip is a bridge (pardon the pun) between the old world of
+ * ISA IDE and PCI IDE. Although the ATA timings are PCI configured the actual
+ * IDE controller is not decoded in PCI space and the chip does not claim to
+ * be IDE class PCI. This requires slightly non-standard probe logic compared
+ * with PCI IDE and also that we do not disable the device when our driver is
+ * unloaded (as it has many other functions).
+ *
+ * The driver consciously keeps this logic internally to avoid pushing quirky
+ * PATA history into the clean libata layer.
+ *
+ * Thinkpad specific note: If you boot an MPIIX using a thinkpad with a PCMCIA
+ * hard disk present this driver will not detect it. This is not a bug. In this
+ * configuration the secondary port of the MPIIX is disabled and the addresses
+ * are decoded by the PCMCIA bridge and therefore are for a generic IDE driver
+ * to operate.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_mpiix"
+#define DRV_VERSION "0.7.7"
+
+enum {
+	IDETIM = 0x6C,		/* IDE control register */
+	IORDY = (1 << 1),
+	PPE = (1 << 2),
+	FTIM = (1 << 0),
+	ENABLED = (1 << 15),
+	SECONDARY = (1 << 14)
+};
+
+static int mpiix_pre_reset(struct ata_link *link, unsigned long deadline)
+{
+	struct ata_port *ap = link->ap;
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	static const struct pci_bits mpiix_enable_bits = { 0x6D, 1, 0x80, 0x80 };
+
+	if (!pci_test_config_bits(pdev, &mpiix_enable_bits))
+		return -ENOENT;
+
+	return ata_sff_prereset(link, deadline);
+}
+
+/**
+ *	mpiix_set_piomode	-	set initial PIO mode data
+ *	@ap: ATA interface
+ *	@adev: ATA device
+ *
+ *	Called to do the PIO mode setup. The MPIIX allows us to program the
+ *	IORDY sample point (2-5 clocks), recovery (1-4 clocks) and whether
+ *	prefetching or IORDY are used.
+ *
+ *	This would get very ugly because we can only program timing for one
+ *	device at a time, the other gets PIO0. Fortunately libata calls
+ *	our qc_issue command before a command is issued so we can flip the
+ *	timings back and forth to reduce the pain.
+ */
+
+static void mpiix_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+	int control = 0;
+	int pio = adev->pio_mode - XFER_PIO_0;
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	u16 idetim;
+	static const	 /* ISP  RTC */
+	u8 timings[][2]	= { { 0, 0 },
+			    { 0, 0 },
+			    { 1, 0 },
+			    { 2, 1 },
+			    { 2, 3 }, };
+
+	pci_read_config_word(pdev, IDETIM, &idetim);
+
+	/* Mask the IORDY/TIME/PPE for this device */
+	if (adev->class == ATA_DEV_ATA)
+		control |= PPE;		/* Enable prefetch/posting for disk */
+	if (ata_pio_need_iordy(adev))
+		control |= IORDY;
+	if (pio > 1)
+		control |= FTIM;	/* This drive is on the fast timing bank */
+
+	/* Mask out timing and clear both TIME bank selects */
+	idetim &= 0xCCEE;
+	idetim &= ~(0x07  << (4 * adev->devno));
+	idetim |= control << (4 * adev->devno);
+
+	idetim |= (timings[pio][0] << 12) | (timings[pio][1] << 8);
+	pci_write_config_word(pdev, IDETIM, idetim);
+
+	/* We use ap->private_data as a pointer to the device currently
+	   loaded for timing */
+	ap->private_data = adev;
+}
+
+/**
+ *	mpiix_qc_issue		-	command issue
+ *	@qc: command pending
+ *
+ *	Called when the libata layer is about to issue a command. We wrap
+ *	this interface so that we can load the correct ATA timings if
+ *	necessary. Our logic also clears TIME0/TIME1 for the other device so
+ *	that, even if we get this wrong, cycles to the other device will
+ *	be made PIO0.
+ */
+
+static unsigned int mpiix_qc_issue(struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	struct ata_device *adev = qc->dev;
+
+	/* If modes have been configured and the channel data is not loaded
+	   then load it. We have to check if pio_mode is set as the core code
+	   does not set adev->pio_mode to XFER_PIO_0 while probing as would be
+	   logical */
+
+	if (adev->pio_mode && adev != ap->private_data)
+		mpiix_set_piomode(ap, adev);
+
+	return ata_sff_qc_issue(qc);
+}
+
+static struct scsi_host_template mpiix_sht = {
+	ATA_PIO_SHT(DRV_NAME),
+};
+
+static struct ata_port_operations mpiix_port_ops = {
+	.inherits	= &ata_sff_port_ops,
+	.qc_issue	= mpiix_qc_issue,
+	.cable_detect	= ata_cable_40wire,
+	.set_piomode	= mpiix_set_piomode,
+	.prereset	= mpiix_pre_reset,
+	.sff_data_xfer	= ata_sff_data_xfer32,
+};
+
+static int mpiix_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+	/* Single threaded by the PCI probe logic */
+	struct ata_host *host;
+	struct ata_port *ap;
+	void __iomem *cmd_addr, *ctl_addr;
+	u16 idetim;
+	int cmd, ctl, irq;
+
+	ata_print_version_once(&dev->dev, DRV_VERSION);
+
+	host = ata_host_alloc(&dev->dev, 1);
+	if (!host)
+		return -ENOMEM;
+	ap = host->ports[0];
+
+	/* MPIIX has many functions which can be turned on or off according
+	   to other devices present. Make sure IDE is enabled before we try
+	   and use it */
+
+	pci_read_config_word(dev, IDETIM, &idetim);
+	if (!(idetim & ENABLED))
+		return -ENODEV;
+
+	/* See if it's primary or secondary channel... */
+	if (!(idetim & SECONDARY)) {
+		cmd = 0x1F0;
+		ctl = 0x3F6;
+		irq = 14;
+	} else {
+		cmd = 0x170;
+		ctl = 0x376;
+		irq = 15;
+	}
+
+	cmd_addr = devm_ioport_map(&dev->dev, cmd, 8);
+	ctl_addr = devm_ioport_map(&dev->dev, ctl, 1);
+	if (!cmd_addr || !ctl_addr)
+		return -ENOMEM;
+
+	ata_port_desc(ap, "cmd 0x%x ctl 0x%x", cmd, ctl);
+
+	/* We do our own plumbing to avoid leaking special cases for whacko
+	   ancient hardware into the core code. There are two issues to
+	   worry about.  #1 The chip is a bridge so if in legacy mode and
+	   without BARs set fools the setup.  #2 If you pci_disable_device
+	   the MPIIX your box goes castors up */
+
+	ap->ops = &mpiix_port_ops;
+	ap->pio_mask = ATA_PIO4;
+	ap->flags |= ATA_FLAG_SLAVE_POSS;
+
+	ap->ioaddr.cmd_addr = cmd_addr;
+	ap->ioaddr.ctl_addr = ctl_addr;
+	ap->ioaddr.altstatus_addr = ctl_addr;
+
+	/* Let libata fill in the port details */
+	ata_sff_std_ports(&ap->ioaddr);
+
+	/* activate host */
+	return ata_host_activate(host, irq, ata_sff_interrupt, IRQF_SHARED,
+				 &mpiix_sht);
+}
+
+static const struct pci_device_id mpiix[] = {
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371MX), },
+
+	{ },
+};
+
+static struct pci_driver mpiix_pci_driver = {
+	.name 		= DRV_NAME,
+	.id_table	= mpiix,
+	.probe 		= mpiix_init_one,
+	.remove		= ata_pci_remove_one,
+#ifdef CONFIG_PM
+	.suspend	= ata_pci_device_suspend,
+	.resume		= ata_pci_device_resume,
+#endif
+};
+
+static int __init mpiix_init(void)
+{
+	return pci_register_driver(&mpiix_pci_driver);
+}
+
+static void __exit mpiix_exit(void)
+{
+	pci_unregister_driver(&mpiix_pci_driver);
+}
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for Intel MPIIX");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, mpiix);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(mpiix_init);
+module_exit(mpiix_exit);