Moved, renamed, and deleted files

The original directory structure was scattered and unorganized.
Changes are basically to make it look like kernel structure.

1 files changed, 362 insertions, 0 deletions

diff --git a/arch/arm/mach-orion5x/d2net-setup.c b/arch/arm/mach-orion5x/d2net-setup.c
new file mode 100644
index 00000000..d75dcfa0
--- /dev/null
+++ b/arch/arm/mach-orion5x/d2net-setup.c
@@ -0,0 +1,362 @@
+/*
+ * arch/arm/mach-orion5x/d2net-setup.c
+ *
+ * LaCie d2Network and Big Disk Network NAS setup
+ *
+ * Copyright (C) 2009 Simon Guinot <sguinot@lacie.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/pci.h>
+#include <linux/irq.h>
+#include <linux/mtd/physmap.h>
+#include <linux/mv643xx_eth.h>
+#include <linux/leds.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
+#include <linux/i2c.h>
+#include <linux/ata_platform.h>
+#include <linux/gpio.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/pci.h>
+#include <mach/orion5x.h>
+#include "common.h"
+#include "mpp.h"
+
+/*****************************************************************************
+ * LaCie d2 Network Info
+ ****************************************************************************/
+
+/*
+ * 512KB NOR flash Device bus boot chip select
+ */
+
+#define D2NET_NOR_BOOT_BASE		0xfff80000
+#define D2NET_NOR_BOOT_SIZE		SZ_512K
+
+/*****************************************************************************
+ * 512KB NOR Flash on Boot Device
+ ****************************************************************************/
+
+/*
+ * TODO: Check write support on flash MX29LV400CBTC-70G
+ */
+
+static struct mtd_partition d2net_partitions[] = {
+	{
+		.name		= "Full512kb",
+		.size		= MTDPART_SIZ_FULL,
+		.offset		= 0,
+		.mask_flags	= MTD_WRITEABLE,
+	},
+};
+
+static struct physmap_flash_data d2net_nor_flash_data = {
+	.width		= 1,
+	.parts		= d2net_partitions,
+	.nr_parts	= ARRAY_SIZE(d2net_partitions),
+};
+
+static struct resource d2net_nor_flash_resource = {
+	.flags			= IORESOURCE_MEM,
+	.start			= D2NET_NOR_BOOT_BASE,
+	.end			= D2NET_NOR_BOOT_BASE
+					+ D2NET_NOR_BOOT_SIZE - 1,
+};
+
+static struct platform_device d2net_nor_flash = {
+	.name			= "physmap-flash",
+	.id			= 0,
+	.dev		= {
+		.platform_data	= &d2net_nor_flash_data,
+	},
+	.num_resources		= 1,
+	.resource		= &d2net_nor_flash_resource,
+};
+
+/*****************************************************************************
+ * Ethernet
+ ****************************************************************************/
+
+static struct mv643xx_eth_platform_data d2net_eth_data = {
+	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
+};
+
+/*****************************************************************************
+ * I2C devices
+ ****************************************************************************/
+
+/*
+ * i2c addr | chip         | description
+ * 0x32     | Ricoh 5C372b | RTC
+ * 0x3e     | GMT G762     | PWM fan controller
+ * 0x50     | HT24LC08     | eeprom (1kB)
+ *
+ * TODO: Add G762 support to the g760a driver.
+ */
+static struct i2c_board_info __initdata d2net_i2c_devices[] = {
+	{
+		I2C_BOARD_INFO("rs5c372b", 0x32),
+	}, {
+		I2C_BOARD_INFO("24c08", 0x50),
+	},
+};
+
+/*****************************************************************************
+ * SATA
+ ****************************************************************************/
+
+static struct mv_sata_platform_data d2net_sata_data = {
+	.n_ports	= 2,
+};
+
+#define D2NET_GPIO_SATA0_POWER	3
+#define D2NET_GPIO_SATA1_POWER	12
+
+static void __init d2net_sata_power_init(void)
+{
+	int err;
+
+	err = gpio_request(D2NET_GPIO_SATA0_POWER, "SATA0 power");
+	if (err == 0) {
+		err = gpio_direction_output(D2NET_GPIO_SATA0_POWER, 1);
+		if (err)
+			gpio_free(D2NET_GPIO_SATA0_POWER);
+	}
+	if (err)
+		pr_err("d2net: failed to configure SATA0 power GPIO\n");
+
+	err = gpio_request(D2NET_GPIO_SATA1_POWER, "SATA1 power");
+	if (err == 0) {
+		err = gpio_direction_output(D2NET_GPIO_SATA1_POWER, 1);
+		if (err)
+			gpio_free(D2NET_GPIO_SATA1_POWER);
+	}
+	if (err)
+		pr_err("d2net: failed to configure SATA1 power GPIO\n");
+}
+
+/*****************************************************************************
+ * GPIO LED's
+ ****************************************************************************/
+
+/*
+ * The blue front LED is wired to the CPLD and can blink in relation with the
+ * SATA activity.
+ *
+ * The following array detail the different LED registers and the combination
+ * of their possible values:
+ *
+ * led_off   | blink_ctrl | SATA active | LED state
+ *           |            |             |
+ *    1      |     x      |      x      |  off
+ *    0      |     0      |      0      |  off
+ *    0      |     1      |      0      |  blink (rate 300ms)
+ *    0      |     x      |      1      |  on
+ *
+ * Notes: The blue and the red front LED's can't be on at the same time.
+ *        Red LED have priority.
+ */
+
+#define D2NET_GPIO_RED_LED		6
+#define D2NET_GPIO_BLUE_LED_BLINK_CTRL	16
+#define D2NET_GPIO_BLUE_LED_OFF		23
+
+static struct gpio_led d2net_leds[] = {
+	{
+		.name = "d2net:blue:sata",
+		.default_trigger = "default-on",
+		.gpio = D2NET_GPIO_BLUE_LED_OFF,
+		.active_low = 1,
+	},
+	{
+		.name = "d2net:red:fail",
+		.gpio = D2NET_GPIO_RED_LED,
+	},
+};
+
+static struct gpio_led_platform_data d2net_led_data = {
+	.num_leds = ARRAY_SIZE(d2net_leds),
+	.leds = d2net_leds,
+};
+
+static struct platform_device d2net_gpio_leds = {
+	.name           = "leds-gpio",
+	.id             = -1,
+	.dev            = {
+		.platform_data  = &d2net_led_data,
+	},
+};
+
+static void __init d2net_gpio_leds_init(void)
+{
+	int err;
+
+	/* Configure GPIO over MPP max number. */
+	orion_gpio_set_valid(D2NET_GPIO_BLUE_LED_OFF, 1);
+
+	/* Configure register blink_ctrl to allow SATA activity LED blinking. */
+	err = gpio_request(D2NET_GPIO_BLUE_LED_BLINK_CTRL, "blue LED blink");
+	if (err == 0) {
+		err = gpio_direction_output(D2NET_GPIO_BLUE_LED_BLINK_CTRL, 1);
+		if (err)
+			gpio_free(D2NET_GPIO_BLUE_LED_BLINK_CTRL);
+	}
+	if (err)
+		pr_err("d2net: failed to configure blue LED blink GPIO\n");
+
+	platform_device_register(&d2net_gpio_leds);
+}
+
+/****************************************************************************
+ * GPIO keys
+ ****************************************************************************/
+
+#define D2NET_GPIO_PUSH_BUTTON		18
+#define D2NET_GPIO_POWER_SWITCH_ON	8
+#define D2NET_GPIO_POWER_SWITCH_OFF	9
+
+#define D2NET_SWITCH_POWER_ON		0x1
+#define D2NET_SWITCH_POWER_OFF		0x2
+
+static struct gpio_keys_button d2net_buttons[] = {
+	{
+		.type		= EV_SW,
+		.code		= D2NET_SWITCH_POWER_OFF,
+		.gpio		= D2NET_GPIO_POWER_SWITCH_OFF,
+		.desc		= "Power rocker switch (auto|off)",
+		.active_low	= 0,
+	},
+	{
+		.type		= EV_SW,
+		.code		= D2NET_SWITCH_POWER_ON,
+		.gpio		= D2NET_GPIO_POWER_SWITCH_ON,
+		.desc		= "Power rocker switch (on|auto)",
+		.active_low	= 0,
+	},
+	{
+		.type		= EV_KEY,
+		.code		= KEY_POWER,
+		.gpio		= D2NET_GPIO_PUSH_BUTTON,
+		.desc		= "Front Push Button",
+		.active_low	= 0,
+	},
+};
+
+static struct gpio_keys_platform_data d2net_button_data = {
+	.buttons	= d2net_buttons,
+	.nbuttons	= ARRAY_SIZE(d2net_buttons),
+};
+
+static struct platform_device d2net_gpio_buttons = {
+	.name		= "gpio-keys",
+	.id		= -1,
+	.dev		= {
+		.platform_data	= &d2net_button_data,
+	},
+};
+
+/*****************************************************************************
+ * General Setup
+ ****************************************************************************/
+
+static unsigned int d2net_mpp_modes[] __initdata = {
+	MPP0_GPIO,	/* Board ID (bit 0) */
+	MPP1_GPIO,	/* Board ID (bit 1) */
+	MPP2_GPIO,	/* Board ID (bit 2) */
+	MPP3_GPIO,	/* SATA 0 power */
+	MPP4_UNUSED,
+	MPP5_GPIO,	/* Fan fail detection */
+	MPP6_GPIO,	/* Red front LED */
+	MPP7_UNUSED,
+	MPP8_GPIO,	/* Rear power switch (on|auto) */
+	MPP9_GPIO,	/* Rear power switch (auto|off) */
+	MPP10_UNUSED,
+	MPP11_UNUSED,
+	MPP12_GPIO,	/* SATA 1 power */
+	MPP13_UNUSED,
+	MPP14_SATA_LED,	/* SATA 0 active */
+	MPP15_SATA_LED,	/* SATA 1 active */
+	MPP16_GPIO,	/* Blue front LED blink control */
+	MPP17_UNUSED,
+	MPP18_GPIO,	/* Front button (0 = Released, 1 = Pushed ) */
+	MPP19_UNUSED,
+	0,
+	/* 22: USB port 1 fuse (0 = Fail, 1 = Ok) */
+	/* 23: Blue front LED off */
+	/* 24: Inhibit board power off (0 = Disabled, 1 = Enabled) */
+};
+
+#define D2NET_GPIO_INHIBIT_POWER_OFF    24
+
+static void __init d2net_init(void)
+{
+	/*
+	 * Setup basic Orion functions. Need to be called early.
+	 */
+	orion5x_init();
+
+	orion5x_mpp_conf(d2net_mpp_modes);
+
+	/*
+	 * Configure peripherals.
+	 */
+	orion5x_ehci0_init();
+	orion5x_eth_init(&d2net_eth_data);
+	orion5x_i2c_init();
+	orion5x_uart0_init();
+
+	d2net_sata_power_init();
+	orion5x_sata_init(&d2net_sata_data);
+
+	orion5x_setup_dev_boot_win(D2NET_NOR_BOOT_BASE,
+				D2NET_NOR_BOOT_SIZE);
+	platform_device_register(&d2net_nor_flash);
+
+	platform_device_register(&d2net_gpio_buttons);
+
+	d2net_gpio_leds_init();
+
+	pr_notice("d2net: Flash write are not yet supported.\n");
+
+	i2c_register_board_info(0, d2net_i2c_devices,
+				ARRAY_SIZE(d2net_i2c_devices));
+
+	orion_gpio_set_valid(D2NET_GPIO_INHIBIT_POWER_OFF, 1);
+}
+
+/* Warning: LaCie use a wrong mach-type (0x20e=526) in their bootloader. */
+
+#ifdef CONFIG_MACH_D2NET
+MACHINE_START(D2NET, "LaCie d2 Network")
+	.atag_offset	= 0x100,
+	.init_machine	= d2net_init,
+	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
+	.init_irq	= orion5x_init_irq,
+	.timer		= &orion5x_timer,
+	.fixup		= tag_fixup_mem32,
+	.restart	= orion5x_restart,
+MACHINE_END
+#endif
+
+#ifdef CONFIG_MACH_BIGDISK
+MACHINE_START(BIGDISK, "LaCie Big Disk Network")
+	.atag_offset	= 0x100,
+	.init_machine	= d2net_init,
+	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
+	.init_irq	= orion5x_init_irq,
+	.timer		= &orion5x_timer,
+	.fixup		= tag_fixup_mem32,
+	.restart	= orion5x_restart,
+MACHINE_END
+#endif
+