Moved, renamed, and deleted files

The original directory structure was scattered and unorganized.
Changes are basically to make it look like kernel structure.

1 files changed, 0 insertions, 114 deletions

diff --git a/ANDROID_3.4.5/include/linux/pinctrl/pinconf-generic.h b/ANDROID_3.4.5/include/linux/pinctrl/pinconf-generic.h
deleted file mode 100644
index 4f0abb9f..00000000
--- a/ANDROID_3.4.5/include/linux/pinctrl/pinconf-generic.h
+++ /dev/null
@@ -1,114 +0,0 @@
-/*
- * Interface the generic pinconfig portions of the pinctrl subsystem
- *
- * Copyright (C) 2011 ST-Ericsson SA
- * Written on behalf of Linaro for ST-Ericsson
- * This interface is used in the core to keep track of pins.
- *
- * Author: Linus Walleij <linus.walleij@linaro.org>
- *
- * License terms: GNU General Public License (GPL) version 2
- */
-#ifndef __LINUX_PINCTRL_PINCONF_GENERIC_H
-#define __LINUX_PINCTRL_PINCONF_GENERIC_H
-
-/*
- * You shouldn't even be able to compile with these enums etc unless you're
- * using generic pin config. That is why this is defined out.
- */
-#ifdef CONFIG_GENERIC_PINCONF
-
-/**
- * enum pin_config_param - possible pin configuration parameters
- * @PIN_CONFIG_BIAS_DISABLE: disable any pin bias on the pin, a
- *	transition from say pull-up to pull-down implies that you disable
- *	pull-up in the process, this setting disables all biasing.
- * @PIN_CONFIG_BIAS_HIGH_IMPEDANCE: the pin will be set to a high impedance
- *	mode, also know as "third-state" (tristate) or "high-Z" or "floating".
- *	On output pins this effectively disconnects the pin, which is useful
- *	if for example some other pin is going to drive the signal connected
- *	to it for a while. Pins used for input are usually always high
- *	impedance.
- * @PIN_CONFIG_BIAS_PULL_UP: the pin will be pulled up (usually with high
- *	impedance to VDD). If the argument is != 0 pull-up is enabled,
- *	if it is 0, pull-up is disabled.
- * @PIN_CONFIG_BIAS_PULL_DOWN: the pin will be pulled down (usually with high
- *	impedance to GROUND). If the argument is != 0 pull-down is enabled,
- *	if it is 0, pull-down is disabled.
- * @PIN_CONFIG_DRIVE_PUSH_PULL: the pin will be driven actively high and
- *	low, this is the most typical case and is typically achieved with two
- *	active transistors on the output. Sending this config will enabale
- *	push-pull mode, the argument is ignored.
- * @PIN_CONFIG_DRIVE_OPEN_DRAIN: the pin will be driven with open drain (open
- *	collector) which means it is usually wired with other output ports
- *	which are then pulled up with an external resistor. Sending this
- *	config will enabale open drain mode, the argument is ignored.
- * @PIN_CONFIG_DRIVE_OPEN_SOURCE: the pin will be driven with open source
- *	(open emitter). Sending this config will enabale open drain mode, the
- *	argument is ignored.
- * @PIN_CONFIG_INPUT_SCHMITT: this will configure an input pin to run in
- *	schmitt-trigger mode. If the schmitt-trigger has adjustable hysteresis,
- *	the threshold value is given on a custom format as argument when
- *	setting pins to this mode. The argument zero turns the schmitt trigger
- *	off.
- * @PIN_CONFIG_INPUT_DEBOUNCE: this will configure the pin to debounce mode,
- *	which means it will wait for signals to settle when reading inputs. The
- *	argument gives the debounce time on a custom format. Setting the
- *	argument to zero turns debouncing off.
- * @PIN_CONFIG_POWER_SOURCE: if the pin can select between different power
- *	supplies, the argument to this parameter (on a custom format) tells
- *	the driver which alternative power source to use.
- * @PIN_CONFIG_LOW_POWER_MODE: this will configure the pin for low power
- *	operation, if several modes of operation are supported these can be
- *	passed in the argument on a custom form, else just use argument 1
- *	to indicate low power mode, argument 0 turns low power mode off.
- * @PIN_CONFIG_END: this is the last enumerator for pin configurations, if
- *	you need to pass in custom configurations to the pin controller, use
- *	PIN_CONFIG_END+1 as the base offset.
- */
-enum pin_config_param {
-	PIN_CONFIG_BIAS_DISABLE,
-	PIN_CONFIG_BIAS_HIGH_IMPEDANCE,
-	PIN_CONFIG_BIAS_PULL_UP,
-	PIN_CONFIG_BIAS_PULL_DOWN,
-	PIN_CONFIG_DRIVE_PUSH_PULL,
-	PIN_CONFIG_DRIVE_OPEN_DRAIN,
-	PIN_CONFIG_DRIVE_OPEN_SOURCE,
-	PIN_CONFIG_INPUT_SCHMITT,
-	PIN_CONFIG_INPUT_DEBOUNCE,
-	PIN_CONFIG_POWER_SOURCE,
-	PIN_CONFIG_LOW_POWER_MODE,
-	PIN_CONFIG_END = 0x7FFF,
-};
-
-/*
- * Helpful configuration macro to be used in tables etc.
- */
-#define PIN_CONF_PACKED(p, a) ((a << 16) | ((unsigned long) p & 0xffffUL))
-
-/*
- * The following inlines stuffs a configuration parameter and data value
- * into and out of an unsigned long argument, as used by the generic pin config
- * system. We put the parameter in the lower 16 bits and the argument in the
- * upper 16 bits.
- */
-
-static inline enum pin_config_param pinconf_to_config_param(unsigned long config)
-{
-	return (enum pin_config_param) (config & 0xffffUL);
-}
-
-static inline u16 pinconf_to_config_argument(unsigned long config)
-{
-	return (enum pin_config_param) ((config >> 16) & 0xffffUL);
-}
-
-static inline unsigned long pinconf_to_config_packed(enum pin_config_param param,
-						     u16 argument)
-{
-	return PIN_CONF_PACKED(param, argument);
-}
-
-#endif /* CONFIG_GENERIC_PINCONF */
-
-#endif /* __LINUX_PINCTRL_PINCONF_GENERIC_H */