| Age | Commit message (Expand) | Author |
|---|
| 2009-01-31 | minor rev increase for for 3.01, which was just pcb cosmetic changes | matt |
| 2009-01-31 | work with the set reg functions | jblum |
| 2009-01-30 | xcvr: initialize chipset | jblum |
| 2009-01-30 | converted set freq in xcvr | jblum |
| 2009-01-30 | work on xcvr set_freq | jblum |
| 2009-01-30 | xcvr dboard support | jblum |
| 2009-01-29 | tunes the dbsrx properly. You need to mod your dbsrx, though. | matt |
| 2009-01-28 | dbsrx daughterboard support, gain works, not freq | matt |
| 2009-01-27 | third time's a charm... | eb |
| 2009-01-27 | added missing .h files | eb |
| 2009-01-27 | Merged eb/u2-mimo-wip -r10297:10317 into the trunk. This contains | eb |
| 2009-01-27 | General housekeeping--removing ancient cruft mostly. | jcorgan |
| 2009-01-23 | mimo tx work-in-progress | eb |
| 2009-01-23 | revert extraction of buffer_state | eb |
| 2009-01-23 | Work in progress on mimo Tx state machine. | eb |
| 2009-01-22 | bumped stack to 3k (not sure we needed to), cleaned up old serdes test | eb |
| 2009-01-22 | trial fix for problem when 3 loads with 1 wait state are followed by a barrel... | matt |
| 2009-01-22 | catching up with shawn. these aren't used here anyway. | matt |
| 2009-01-22 | detect loss of signal | matt |
| 2009-01-19 | only set scale_iq if asked | jcorgan |
| 2009-01-19 | corrected link up detector | matt |
| 2009-01-19 | new cordic | matt |
| 2009-01-19 | widen cordic on tx side | matt |
| 2009-01-19 | clarify comment | matt |
| 2009-01-19 | 24 bit wide z. Can't do this parameterized, unfortunately. | matt |
| 2008-12-31 | Fix USRP2 peek32() max words | jcorgan |
| 2008-12-31 | For USRP2, implement auto scaling of TX pipeline such that [-1.0 1.0] input to | jcorgan |
| 2008-12-31 | Rename constant for clarity | jcorgan |
| 2008-12-29 | Implements USRP2 poke32() command. | jcorgan |
| 2008-12-28 | Fix typo | jcorgan |
| 2008-12-28 | Replaced USRP2 peek() with peek32(), handles endian-swapping if needed | jcorgan |
| 2008-12-27 | Implements USRP2 peek() command, allowing arbitrary reads from the internal | jcorgan |
| 2008-12-24 | Merged r10071:10164 from features/cppdb-test into trunk. Implements the full... | jcorgan |
| 2008-12-17 | added frequency offset capability. Set to 12.5e6 on TX, 0 on RX for now | matt |
| 2008-12-15 | pps sync works, meets timing | matt |
| 2008-12-14 | add break at end of new case to prevent fallthru. Also cleared up a warning. | matt |
| 2008-12-14 | synchronized pps, lots of debug pins changed, works, meets timing | matt |
| 2008-12-14 | Fix failure with interp > 128 | jcorgan |
| 2008-12-14 | Implement sync_to_pps command for USRP2 | jcorgan |
| 2008-12-13 | reset the phase when we shut down. Aids in sync | matt |
| 2008-12-07 | split test out into a function | matt |
| 2008-12-07 | more tests, for ram and sd card | matt |
| 2008-12-05 | implemented "reset master clock on next PPS" so we can easily sync multiple u... | matt |
| 2008-12-05 | send a char to the serial port, but don't wait if the queue is full | matt |
| 2008-12-04 | speed up the diagnostic signals, they were causing timing problems | matt |
| 2008-11-16 | removed old python comments | matt |
| 2008-11-16 | fixed gain calculations rfx900-2400 | matt |
| 2008-11-16 | added a utility function to get the integer rounded gain | matt |
| 2008-11-09 | more thorough test | matt |
| 2008-11-09 | hardware control of leds | matt |
