From 871480933a1c28f8a9fed4c4d34d06c439a7a422 Mon Sep 17 00:00:00 2001
From: Srikant Patnaik
Date: Sun, 11 Jan 2015 12:28:04 +0530
Subject: Moved, renamed, and deleted files

The original directory structure was scattered and unorganized.
Changes are basically to make it look like kernel structure.
---
 drivers/video/omap2/dss/Kconfig | 131 ++++++++++++++++++++++++++++++++++++++++
 1 file changed, 131 insertions(+)
 create mode 100644 drivers/video/omap2/dss/Kconfig

(limited to 'drivers/video/omap2/dss/Kconfig')

diff --git a/drivers/video/omap2/dss/Kconfig b/drivers/video/omap2/dss/Kconfig
new file mode 100644
index 00000000..7be7c06a
--- /dev/null
+++ b/drivers/video/omap2/dss/Kconfig
@@ -0,0 +1,131 @@
+menuconfig OMAP2_DSS
+        tristate "OMAP2+ Display Subsystem support"
+        depends on ARCH_OMAP2PLUS
+        help
+	  OMAP2+ Display Subsystem support.
+
+if OMAP2_DSS
+
+config OMAP2_VRAM_SIZE
+	int "VRAM size (MB)"
+	range 0 32
+	default 0
+	help
+	  The amount of SDRAM to reserve at boot time for video RAM use.
+	  This VRAM will be used by omapfb and other drivers that need
+	  large continuous RAM area for video use.
+
+	  You can also set this with "vram=<bytes>" kernel argument, or
+	  in the board file.
+
+config OMAP2_DSS_DEBUG_SUPPORT
+        bool "Debug support"
+	default y
+	help
+	  This enables debug messages. You need to enable printing
+	  with 'debug' module parameter.
+
+config OMAP2_DSS_COLLECT_IRQ_STATS
+	bool "Collect DSS IRQ statistics"
+	depends on OMAP2_DSS_DEBUG_SUPPORT
+	default n
+	help
+	  Collect DSS IRQ statistics, printable via debugfs.
+
+	  The statistics can be found from
+	  <debugfs>/omapdss/dispc_irq for DISPC interrupts, and
+	  <debugfs>/omapdss/dsi_irq for DSI interrupts.
+
+config OMAP2_DSS_DPI
+	bool "DPI support"
+	default y
+	help
+	  DPI Interface. This is the Parallel Display Interface.
+
+config OMAP2_DSS_RFBI
+	bool "RFBI support"
+        default n
+	help
+	  MIPI DBI support (RFBI, Remote Framebuffer Interface, in Texas
+	  Instrument's terminology).
+
+	  DBI is a bus between the host processor and a peripheral,
+	  such as a display or a framebuffer chip.
+
+	  See http://www.mipi.org/ for DBI spesifications.
+
+config OMAP2_DSS_VENC
+	bool "VENC support"
+        default y
+	help
+	  OMAP Video Encoder support for S-Video and composite TV-out.
+
+config OMAP4_DSS_HDMI
+	bool "HDMI support"
+	depends on ARCH_OMAP4
+        default y
+	help
+	  HDMI Interface. This adds the High Definition Multimedia Interface.
+	  See http://www.hdmi.org/ for HDMI specification.
+
+config OMAP2_DSS_SDI
+	bool "SDI support"
+	depends on ARCH_OMAP3
+        default n
+	help
+	  SDI (Serial Display Interface) support.
+
+	  SDI is a high speed one-way display serial bus between the host
+	  processor and a display.
+
+config OMAP2_DSS_DSI
+	bool "DSI support"
+	depends on ARCH_OMAP3 || ARCH_OMAP4
+        default n
+	help
+	  MIPI DSI (Display Serial Interface) support.
+
+	  DSI is a high speed half-duplex serial interface between the host
+	  processor and a peripheral, such as a display or a framebuffer chip.
+
+	  See http://www.mipi.org/ for DSI spesifications.
+
+config OMAP2_DSS_FAKE_VSYNC
+	bool "Fake VSYNC irq from manual update displays"
+	default n
+	help
+	  If this is selected, DSI will generate a fake DISPC VSYNC interrupt
+	  when DSI has sent a frame. This is only needed with DSI or RFBI
+	  displays using manual mode, and you want VSYNC to, for example,
+	  time animation.
+
+config OMAP2_DSS_MIN_FCK_PER_PCK
+	int "Minimum FCK/PCK ratio (for scaling)"
+	range 0 32
+	default 0
+	help
+	  This can be used to adjust the minimum FCK/PCK ratio.
+
+	  With this you can make sure that DISPC FCK is at least
+	  n x PCK. Video plane scaling requires higher FCK than
+	  normally.
+
+	  If this is set to 0, there's no extra constraint on the
+	  DISPC FCK. However, the FCK will at minimum be
+	  2xPCK (if active matrix) or 3xPCK (if passive matrix).
+
+	  Max FCK is 173MHz, so this doesn't work if your PCK
+	  is very high.
+
+config OMAP2_DSS_SLEEP_AFTER_VENC_RESET
+	bool "Sleep 20ms after VENC reset"
+	default y
+	help
+	  There is a 20ms sleep after VENC reset which seemed to fix the
+	  reset. The reason for the bug is unclear, and it's also unclear
+	  on what platforms this happens.
+
+	  This option enables the sleep, and is enabled by default. You can
+	  disable the sleep if it doesn't cause problems on your platform.
+
+endif
-- 
cgit