From 871480933a1c28f8a9fed4c4d34d06c439a7a422 Mon Sep 17 00:00:00 2001 From: Srikant Patnaik Date: Sun, 11 Jan 2015 12:28:04 +0530 Subject: Moved, renamed, and deleted files The original directory structure was scattered and unorganized. Changes are basically to make it look like kernel structure. --- Documentation/scsi/qlogicfas.txt | 78 ++++++++++++++++++++++++++++++++++++++++ 1 file changed, 78 insertions(+) create mode 100644 Documentation/scsi/qlogicfas.txt (limited to 'Documentation/scsi/qlogicfas.txt') diff --git a/Documentation/scsi/qlogicfas.txt b/Documentation/scsi/qlogicfas.txt new file mode 100644 index 00000000..c211d827 --- /dev/null +++ b/Documentation/scsi/qlogicfas.txt @@ -0,0 +1,78 @@ + +This driver supports the Qlogic FASXXX family of chips. This driver +only works with the ISA, VLB, and PCMCIA versions of the Qlogic +FastSCSI! cards as well as any other card based on the FASXX chip +(including the Control Concepts SCSI/IDE/SIO/PIO/FDC cards). + +This driver does NOT support the PCI version. Support for these PCI +Qlogic boards: + + * IQ-PCI + * IQ-PCI-10 + * IQ-PCI-D + +is provided by the qla1280 driver. + +Nor does it support the PCI-Basic, which is supported by the +'am53c974' driver. + +PCMCIA SUPPORT + +This currently only works if the card is enabled first from DOS. This +means you will have to load your socket and card services, and +QL41DOS.SYS and QL40ENBL.SYS. These are a minimum, but loading the +rest of the modules won't interfere with the operation. The next +thing to do is load the kernel without resetting the hardware, which +can be a simple ctrl-alt-delete with a boot floppy, or by using +loadlin with the kernel image accessible from DOS. If you are using +the Linux PCMCIA driver, you will have to adjust it or otherwise stop +it from configuring the card. + +I am working with the PCMCIA group to make it more flexible, but that +may take a while. + +ALL CARDS + +The top of the qlogic.c file has a number of defines that controls +configuration. As shipped, it provides a balance between speed and +function. If there are any problems, try setting SLOW_CABLE to 1, and +then try changing USE_IRQ and TURBO_PDMA to zero. If you are familiar +with SCSI, there are other settings which can tune the bus. + +It may be a good idea to enable RESET_AT_START, especially if the +devices may not have been just powered up, or if you are restarting +after a crash, since they may be busy trying to complete the last +command or something. It comes up faster if this is set to zero, and +if you have reliable hardware and connections it may be more useful to +not reset things. + +SOME TROUBLESHOOTING TIPS + +Make sure it works properly under DOS. You should also do an initial FDISK +on a new drive if you want partitions. + +Don't enable all the speedups first. If anything is wrong, they will make +any problem worse. + +IMPORTANT + +The best way to test if your cables, termination, etc. are good is to +copy a very big file (e.g. a doublespace container file, or a very +large executable or archive). It should be at least 5 megabytes, but +you can do multiple tests on smaller files. Then do a COMP to verify +that the file copied properly. (Turn off all caching when doing these +tests, otherwise you will test your RAM and not the files). Then do +10 COMPs, comparing the same file on the SCSI hard drive, i.e. "COMP +realbig.doc realbig.doc". Then do it after the computer gets warm. + +I noticed my system which seems to work 100% would fail this test if +the computer was left on for a few hours. It was worse with longer +cables, and more devices on the SCSI bus. What seems to happen is +that it gets a false ACK causing an extra byte to be inserted into the +stream (and this is not detected). This can be caused by bad +termination (the ACK can be reflected), or by noise when the chips +work less well because of the heat, or when cables get too long for +the speed. + +Remember, if it doesn't work under DOS, it probably won't work under +Linux. -- cgit