From 871480933a1c28f8a9fed4c4d34d06c439a7a422 Mon Sep 17 00:00:00 2001 From: Srikant Patnaik Date: Sun, 11 Jan 2015 12:28:04 +0530 Subject: Moved, renamed, and deleted files The original directory structure was scattered and unorganized. Changes are basically to make it look like kernel structure. --- .../devicetree/bindings/net/can/cc770.txt | 53 ++++++++++++++++++++++ .../devicetree/bindings/net/can/fsl-flexcan.txt | 24 ++++++++++ .../devicetree/bindings/net/can/mpc5xxx-mscan.txt | 53 ++++++++++++++++++++++ .../devicetree/bindings/net/can/sja1000.txt | 53 ++++++++++++++++++++++ 4 files changed, 183 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/can/cc770.txt create mode 100644 Documentation/devicetree/bindings/net/can/fsl-flexcan.txt create mode 100644 Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt create mode 100644 Documentation/devicetree/bindings/net/can/sja1000.txt (limited to 'Documentation/devicetree/bindings/net/can') diff --git a/Documentation/devicetree/bindings/net/can/cc770.txt b/Documentation/devicetree/bindings/net/can/cc770.txt new file mode 100644 index 00000000..77027bf6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/cc770.txt @@ -0,0 +1,53 @@ +Memory mapped Bosch CC770 and Intel AN82527 CAN controller + +Note: The CC770 is a CAN controller from Bosch, which is 100% +compatible with the old AN82527 from Intel, but with "bugs" being fixed. + +Required properties: + +- compatible : should be "bosch,cc770" for the CC770 and "intc,82527" + for the AN82527. + +- reg : should specify the chip select, address offset and size required + to map the registers of the controller. The size is usually 0x80. + +- interrupts : property with a value describing the interrupt source + (number and sensitivity) required for the controller. + +Optional properties: + +- bosch,external-clock-frequency : frequency of the external oscillator + clock in Hz. Note that the internal clock frequency used by the + controller is half of that value. If not specified, a default + value of 16000000 (16 MHz) is used. + +- bosch,clock-out-frequency : slock frequency in Hz on the CLKOUT pin. + If not specified or if the specified value is 0, the CLKOUT pin + will be disabled. + +- bosch,slew-rate : slew rate of the CLKOUT signal. If not specified, + a resonable value will be calculated. + +- bosch,disconnect-rx0-input : see data sheet. + +- bosch,disconnect-rx1-input : see data sheet. + +- bosch,disconnect-tx1-output : see data sheet. + +- bosch,polarity-dominant : see data sheet. + +- bosch,divide-memory-clock : see data sheet. + +- bosch,iso-low-speed-mux : see data sheet. + +For further information, please have a look to the CC770 or AN82527. + +Examples: + +can@3,100 { + compatible = "bosch,cc770"; + reg = <3 0x100 0x80>; + interrupts = <2 0>; + interrupt-parent = <&mpic>; + bosch,external-clock-frequency = <16000000>; +}; diff --git a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt new file mode 100644 index 00000000..1ad80d58 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt @@ -0,0 +1,24 @@ +Flexcan CAN contoller on Freescale's ARM and PowerPC system-on-a-chip (SOC). + +Required properties: + +- compatible : Should be "fsl,-flexcan" + + An implementation should also claim any of the following compatibles + that it is fully backwards compatible with: + + - fsl,p1010-flexcan + +- reg : Offset and length of the register set for this device +- interrupts : Interrupt tuple for this device +- clock-frequency : The oscillator frequency driving the flexcan device + +Example: + + can@1c000 { + compatible = "fsl,p1010-flexcan"; + reg = <0x1c000 0x1000>; + interrupts = <48 0x2>; + interrupt-parent = <&mpic>; + clock-frequency = <200000000>; // filled in by bootloader + }; diff --git a/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt b/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt new file mode 100644 index 00000000..2fa4fcd3 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt @@ -0,0 +1,53 @@ +CAN Device Tree Bindings +------------------------ + +(c) 2006-2009 Secret Lab Technologies Ltd +Grant Likely + +fsl,mpc5200-mscan nodes +----------------------- +In addition to the required compatible-, reg- and interrupt-properties, you can +also specify which clock source shall be used for the controller: + +- fsl,mscan-clock-source : a string describing the clock source. Valid values + are: "ip" for ip bus clock + "ref" for reference clock (XTAL) + "ref" is default in case this property is not + present. + +fsl,mpc5121-mscan nodes +----------------------- +In addition to the required compatible-, reg- and interrupt-properties, you can +also specify which clock source and divider shall be used for the controller: + +- fsl,mscan-clock-source : a string describing the clock source. Valid values + are: "ip" for ip bus clock + "ref" for reference clock + "sys" for system clock + If this property is not present, an optimal CAN + clock source and frequency based on the system + clock will be selected. If this is not possible, + the reference clock will be used. + +- fsl,mscan-clock-divider: for the reference and system clock, an additional + clock divider can be specified. By default, a + value of 1 is used. + +Note that the MPC5121 Rev. 1 processor is not supported. + +Examples: + can@1300 { + compatible = "fsl,mpc5121-mscan"; + interrupts = <12 0x8>; + interrupt-parent = <&ipic>; + reg = <0x1300 0x80>; + }; + + can@1380 { + compatible = "fsl,mpc5121-mscan"; + interrupts = <13 0x8>; + interrupt-parent = <&ipic>; + reg = <0x1380 0x80>; + fsl,mscan-clock-source = "ref"; + fsl,mscan-clock-divider = <3>; + }; diff --git a/Documentation/devicetree/bindings/net/can/sja1000.txt b/Documentation/devicetree/bindings/net/can/sja1000.txt new file mode 100644 index 00000000..c2dbcec0 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/sja1000.txt @@ -0,0 +1,53 @@ +Memory mapped SJA1000 CAN controller from NXP (formerly Philips) + +Required properties: + +- compatible : should be "nxp,sja1000". + +- reg : should specify the chip select, address offset and size required + to map the registers of the SJA1000. The size is usually 0x80. + +- interrupts: property with a value describing the interrupt source + (number and sensitivity) required for the SJA1000. + +Optional properties: + +- nxp,external-clock-frequency : Frequency of the external oscillator + clock in Hz. Note that the internal clock frequency used by the + SJA1000 is half of that value. If not specified, a default value + of 16000000 (16 MHz) is used. + +- nxp,tx-output-mode : operation mode of the TX output control logic: + <0x0> : bi-phase output mode + <0x1> : normal output mode (default) + <0x2> : test output mode + <0x3> : clock output mode + +- nxp,tx-output-config : TX output pin configuration: + <0x01> : TX0 invert + <0x02> : TX0 pull-down (default) + <0x04> : TX0 pull-up + <0x06> : TX0 push-pull + <0x08> : TX1 invert + <0x10> : TX1 pull-down + <0x20> : TX1 pull-up + <0x30> : TX1 push-pull + +- nxp,clock-out-frequency : clock frequency in Hz on the CLKOUT pin. + If not specified or if the specified value is 0, the CLKOUT pin + will be disabled. + +- nxp,no-comparator-bypass : Allows to disable the CAN input comperator. + +For further information, please have a look to the SJA1000 data sheet. + +Examples: + +can@3,100 { + compatible = "nxp,sja1000"; + reg = <3 0x100 0x80>; + interrupts = <2 0>; + interrupt-parent = <&mpic>; + nxp,external-clock-frequency = <16000000>; +}; + -- cgit