diff options
Diffstat (limited to 'include/linux/amba')
| -rw-r--r-- | include/linux/amba/bus.h | 130 | ||||
| -rw-r--r-- | include/linux/amba/clcd.h | 330 | ||||
| -rw-r--r-- | include/linux/amba/kmi.h | 92 | ||||
| -rw-r--r-- | include/linux/amba/mmci.h | 90 | ||||
| -rw-r--r-- | include/linux/amba/pl022.h | 300 | ||||
| -rw-r--r-- | include/linux/amba/pl061.h | 16 | ||||
| -rw-r--r-- | include/linux/amba/pl08x.h | 244 | ||||
| -rw-r--r-- | include/linux/amba/pl093.h | 80 | ||||
| -rw-r--r-- | include/linux/amba/pl330.h | 35 | ||||
| -rw-r--r-- | include/linux/amba/serial.h | 212 |
10 files changed, 1529 insertions, 0 deletions
diff --git a/include/linux/amba/bus.h b/include/linux/amba/bus.h new file mode 100644 index 00000000..8d54f794 --- /dev/null +++ b/include/linux/amba/bus.h @@ -0,0 +1,130 @@ +/* + * linux/include/amba/bus.h + * + * This device type deals with ARM PrimeCells and anything else that + * presents a proper CID (0xB105F00D) at the end of the I/O register + * region or that is derived from a PrimeCell. + * + * Copyright (C) 2003 Deep Blue Solutions Ltd, All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#ifndef ASMARM_AMBA_H +#define ASMARM_AMBA_H + +#include <linux/clk.h> +#include <linux/device.h> +#include <linux/mod_devicetable.h> +#include <linux/err.h> +#include <linux/resource.h> +#include <linux/regulator/consumer.h> + +#define AMBA_NR_IRQS 2 +#define AMBA_CID 0xb105f00d + +struct clk; + +struct amba_device { + struct device dev; + struct resource res; + struct clk *pclk; + u64 dma_mask; + unsigned int periphid; + unsigned int irq[AMBA_NR_IRQS]; +}; + +struct amba_driver { + struct device_driver drv; + int (*probe)(struct amba_device *, const struct amba_id *); + int (*remove)(struct amba_device *); + void (*shutdown)(struct amba_device *); + int (*suspend)(struct amba_device *, pm_message_t); + int (*resume)(struct amba_device *); + const struct amba_id *id_table; +}; + +enum amba_vendor { + AMBA_VENDOR_ARM = 0x41, + AMBA_VENDOR_ST = 0x80, +}; + +extern struct bus_type amba_bustype; + +#define to_amba_device(d) container_of(d, struct amba_device, dev) + +#define amba_get_drvdata(d) dev_get_drvdata(&d->dev) +#define amba_set_drvdata(d,p) dev_set_drvdata(&d->dev, p) + +int amba_driver_register(struct amba_driver *); +void amba_driver_unregister(struct amba_driver *); +struct amba_device *amba_device_alloc(const char *, resource_size_t, size_t); +void amba_device_put(struct amba_device *); +int amba_device_add(struct amba_device *, struct resource *); +int amba_device_register(struct amba_device *, struct resource *); +void amba_device_unregister(struct amba_device *); +struct amba_device *amba_find_device(const char *, struct device *, unsigned int, unsigned int); +int amba_request_regions(struct amba_device *, const char *); +void amba_release_regions(struct amba_device *); + +#define amba_pclk_enable(d) \ + (IS_ERR((d)->pclk) ? 0 : clk_enable((d)->pclk)) + +#define amba_pclk_disable(d) \ + do { if (!IS_ERR((d)->pclk)) clk_disable((d)->pclk); } while (0) + +/* Some drivers don't use the struct amba_device */ +#define AMBA_CONFIG_BITS(a) (((a) >> 24) & 0xff) +#define AMBA_REV_BITS(a) (((a) >> 20) & 0x0f) +#define AMBA_MANF_BITS(a) (((a) >> 12) & 0xff) +#define AMBA_PART_BITS(a) ((a) & 0xfff) + +#define amba_config(d) AMBA_CONFIG_BITS((d)->periphid) +#define amba_rev(d) AMBA_REV_BITS((d)->periphid) +#define amba_manf(d) AMBA_MANF_BITS((d)->periphid) +#define amba_part(d) AMBA_PART_BITS((d)->periphid) + +#define __AMBA_DEV(busid, data, mask) \ + { \ + .coherent_dma_mask = mask, \ + .init_name = busid, \ + .platform_data = data, \ + } + +/* + * APB devices do not themselves have the ability to address memory, + * so DMA masks should be zero (much like USB peripheral devices.) + * The DMA controller DMA masks should be used instead (much like + * USB host controllers in conventional PCs.) + */ +#define AMBA_APB_DEVICE(name, busid, id, base, irqs, data) \ +struct amba_device name##_device = { \ + .dev = __AMBA_DEV(busid, data, 0), \ + .res = DEFINE_RES_MEM(base, SZ_4K), \ + .irq = irqs, \ + .periphid = id, \ +} + +/* + * AHB devices are DMA capable, so set their DMA masks + */ +#define AMBA_AHB_DEVICE(name, busid, id, base, irqs, data) \ +struct amba_device name##_device = { \ + .dev = __AMBA_DEV(busid, data, ~0ULL), \ + .res = DEFINE_RES_MEM(base, SZ_4K), \ + .dma_mask = ~0ULL, \ + .irq = irqs, \ + .periphid = id, \ +} + +/* + * module_amba_driver() - Helper macro for drivers that don't do anything + * special in module init/exit. This eliminates a lot of boilerplate. Each + * module may only use this macro once, and calling it replaces module_init() + * and module_exit() + */ +#define module_amba_driver(__amba_drv) \ + module_driver(__amba_drv, amba_driver_register, amba_driver_unregister) + +#endif diff --git a/include/linux/amba/clcd.h b/include/linux/amba/clcd.h new file mode 100644 index 00000000..e82e3ee2 --- /dev/null +++ b/include/linux/amba/clcd.h @@ -0,0 +1,330 @@ +/* + * linux/include/asm-arm/hardware/amba_clcd.h -- Integrator LCD panel. + * + * David A Rusling + * + * Copyright (C) 2001 ARM Limited + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file COPYING in the main directory of this archive + * for more details. + */ +#include <linux/fb.h> + +/* + * CLCD Controller Internal Register addresses + */ +#define CLCD_TIM0 0x00000000 +#define CLCD_TIM1 0x00000004 +#define CLCD_TIM2 0x00000008 +#define CLCD_TIM3 0x0000000c +#define CLCD_UBAS 0x00000010 +#define CLCD_LBAS 0x00000014 + +#define CLCD_PL110_IENB 0x00000018 +#define CLCD_PL110_CNTL 0x0000001c +#define CLCD_PL110_STAT 0x00000020 +#define CLCD_PL110_INTR 0x00000024 +#define CLCD_PL110_UCUR 0x00000028 +#define CLCD_PL110_LCUR 0x0000002C + +#define CLCD_PL111_CNTL 0x00000018 +#define CLCD_PL111_IENB 0x0000001c +#define CLCD_PL111_RIS 0x00000020 +#define CLCD_PL111_MIS 0x00000024 +#define CLCD_PL111_ICR 0x00000028 +#define CLCD_PL111_UCUR 0x0000002c +#define CLCD_PL111_LCUR 0x00000030 + +#define CLCD_PALL 0x00000200 +#define CLCD_PALETTE 0x00000200 + +#define TIM2_CLKSEL (1 << 5) +#define TIM2_IVS (1 << 11) +#define TIM2_IHS (1 << 12) +#define TIM2_IPC (1 << 13) +#define TIM2_IOE (1 << 14) +#define TIM2_BCD (1 << 26) + +#define CNTL_LCDEN (1 << 0) +#define CNTL_LCDBPP1 (0 << 1) +#define CNTL_LCDBPP2 (1 << 1) +#define CNTL_LCDBPP4 (2 << 1) +#define CNTL_LCDBPP8 (3 << 1) +#define CNTL_LCDBPP16 (4 << 1) +#define CNTL_LCDBPP16_565 (6 << 1) +#define CNTL_LCDBPP16_444 (7 << 1) +#define CNTL_LCDBPP24 (5 << 1) +#define CNTL_LCDBW (1 << 4) +#define CNTL_LCDTFT (1 << 5) +#define CNTL_LCDMONO8 (1 << 6) +#define CNTL_LCDDUAL (1 << 7) +#define CNTL_BGR (1 << 8) +#define CNTL_BEBO (1 << 9) +#define CNTL_BEPO (1 << 10) +#define CNTL_LCDPWR (1 << 11) +#define CNTL_LCDVCOMP(x) ((x) << 12) +#define CNTL_LDMAFIFOTIME (1 << 15) +#define CNTL_WATERMARK (1 << 16) + +enum { + /* individual formats */ + CLCD_CAP_RGB444 = (1 << 0), + CLCD_CAP_RGB5551 = (1 << 1), + CLCD_CAP_RGB565 = (1 << 2), + CLCD_CAP_RGB888 = (1 << 3), + CLCD_CAP_BGR444 = (1 << 4), + CLCD_CAP_BGR5551 = (1 << 5), + CLCD_CAP_BGR565 = (1 << 6), + CLCD_CAP_BGR888 = (1 << 7), + + /* connection layouts */ + CLCD_CAP_444 = CLCD_CAP_RGB444 | CLCD_CAP_BGR444, + CLCD_CAP_5551 = CLCD_CAP_RGB5551 | CLCD_CAP_BGR5551, + CLCD_CAP_565 = CLCD_CAP_RGB565 | CLCD_CAP_BGR565, + CLCD_CAP_888 = CLCD_CAP_RGB888 | CLCD_CAP_BGR888, + + /* red/blue ordering */ + CLCD_CAP_RGB = CLCD_CAP_RGB444 | CLCD_CAP_RGB5551 | + CLCD_CAP_RGB565 | CLCD_CAP_RGB888, + CLCD_CAP_BGR = CLCD_CAP_BGR444 | CLCD_CAP_BGR5551 | + CLCD_CAP_BGR565 | CLCD_CAP_BGR888, + + CLCD_CAP_ALL = CLCD_CAP_BGR | CLCD_CAP_RGB, +}; + +struct clcd_panel { + struct fb_videomode mode; + signed short width; /* width in mm */ + signed short height; /* height in mm */ + u32 tim2; + u32 tim3; + u32 cntl; + u32 caps; + unsigned int bpp:8, + fixedtimings:1, + grayscale:1; + unsigned int connector; +}; + +struct clcd_regs { + u32 tim0; + u32 tim1; + u32 tim2; + u32 tim3; + u32 cntl; + unsigned long pixclock; +}; + +struct clcd_fb; + +/* + * the board-type specific routines + */ +struct clcd_board { + const char *name; + + /* + * Optional. Hardware capability flags. + */ + u32 caps; + + /* + * Optional. Check whether the var structure is acceptable + * for this display. + */ + int (*check)(struct clcd_fb *fb, struct fb_var_screeninfo *var); + + /* + * Compulsory. Decode fb->fb.var into regs->*. In the case of + * fixed timing, set regs->* to the register values required. + */ + void (*decode)(struct clcd_fb *fb, struct clcd_regs *regs); + + /* + * Optional. Disable any extra display hardware. + */ + void (*disable)(struct clcd_fb *); + + /* + * Optional. Enable any extra display hardware. + */ + void (*enable)(struct clcd_fb *); + + /* + * Setup platform specific parts of CLCD driver + */ + int (*setup)(struct clcd_fb *); + + /* + * mmap the framebuffer memory + */ + int (*mmap)(struct clcd_fb *, struct vm_area_struct *); + + /* + * Remove platform specific parts of CLCD driver + */ + void (*remove)(struct clcd_fb *); +}; + +struct amba_device; +struct clk; + +/* this data structure describes each frame buffer device we find */ +struct clcd_fb { + struct fb_info fb; + struct amba_device *dev; + struct clk *clk; + struct clcd_panel *panel; + struct clcd_board *board; + void *board_data; + void __iomem *regs; + u16 off_ienb; + u16 off_cntl; + u32 clcd_cntl; + u32 cmap[16]; + bool clk_enabled; +}; + +static inline void clcdfb_decode(struct clcd_fb *fb, struct clcd_regs *regs) +{ + struct fb_var_screeninfo *var = &fb->fb.var; + u32 val, cpl; + + /* + * Program the CLCD controller registers and start the CLCD + */ + val = ((var->xres / 16) - 1) << 2; + val |= (var->hsync_len - 1) << 8; + val |= (var->right_margin - 1) << 16; + val |= (var->left_margin - 1) << 24; + regs->tim0 = val; + + val = var->yres; + if (fb->panel->cntl & CNTL_LCDDUAL) + val /= 2; + val -= 1; + val |= (var->vsync_len - 1) << 10; + val |= var->lower_margin << 16; + val |= var->upper_margin << 24; + regs->tim1 = val; + + val = fb->panel->tim2; + val |= var->sync & FB_SYNC_HOR_HIGH_ACT ? 0 : TIM2_IHS; + val |= var->sync & FB_SYNC_VERT_HIGH_ACT ? 0 : TIM2_IVS; + + cpl = var->xres_virtual; + if (fb->panel->cntl & CNTL_LCDTFT) /* TFT */ + /* / 1 */; + else if (!var->grayscale) /* STN color */ + cpl = cpl * 8 / 3; + else if (fb->panel->cntl & CNTL_LCDMONO8) /* STN monochrome, 8bit */ + cpl /= 8; + else /* STN monochrome, 4bit */ + cpl /= 4; + + regs->tim2 = val | ((cpl - 1) << 16); + + regs->tim3 = fb->panel->tim3; + + val = fb->panel->cntl; + if (var->grayscale) + val |= CNTL_LCDBW; + + if (fb->panel->caps && fb->board->caps && + var->bits_per_pixel >= 16) { + /* + * if board and panel supply capabilities, we can support + * changing BGR/RGB depending on supplied parameters + */ + if (var->red.offset == 0) + val &= ~CNTL_BGR; + else + val |= CNTL_BGR; + } + + switch (var->bits_per_pixel) { + case 1: + val |= CNTL_LCDBPP1; + break; + case 2: + val |= CNTL_LCDBPP2; + break; + case 4: + val |= CNTL_LCDBPP4; + break; + case 8: + val |= CNTL_LCDBPP8; + break; + case 16: + /* + * PL110 cannot choose between 5551 and 565 modes in its + * control register. It is possible to use 565 with + * custom external wiring. + */ + if (amba_part(fb->dev) == 0x110 || + var->green.length == 5) + val |= CNTL_LCDBPP16; + else if (var->green.length == 6) + val |= CNTL_LCDBPP16_565; + else + val |= CNTL_LCDBPP16_444; + break; + case 32: + val |= CNTL_LCDBPP24; + break; + } + + regs->cntl = val; + regs->pixclock = var->pixclock; +} + +static inline int clcdfb_check(struct clcd_fb *fb, struct fb_var_screeninfo *var) +{ + var->xres_virtual = var->xres = (var->xres + 15) & ~15; + var->yres_virtual = var->yres = (var->yres + 1) & ~1; + +#define CHECK(e,l,h) (var->e < l || var->e > h) + if (CHECK(right_margin, (5+1), 256) || /* back porch */ + CHECK(left_margin, (5+1), 256) || /* front porch */ + CHECK(hsync_len, (5+1), 256) || + var->xres > 4096 || + var->lower_margin > 255 || /* back porch */ + var->upper_margin > 255 || /* front porch */ + var->vsync_len > 32 || + var->yres > 1024) + return -EINVAL; +#undef CHECK + + /* single panel mode: PCD = max(PCD, 1) */ + /* dual panel mode: PCD = max(PCD, 5) */ + + /* + * You can't change the grayscale setting, and + * we can only do non-interlaced video. + */ + if (var->grayscale != fb->fb.var.grayscale || + (var->vmode & FB_VMODE_MASK) != FB_VMODE_NONINTERLACED) + return -EINVAL; + +#define CHECK(e) (var->e != fb->fb.var.e) + if (fb->panel->fixedtimings && + (CHECK(xres) || + CHECK(yres) || + CHECK(bits_per_pixel) || + CHECK(pixclock) || + CHECK(left_margin) || + CHECK(right_margin) || + CHECK(upper_margin) || + CHECK(lower_margin) || + CHECK(hsync_len) || + CHECK(vsync_len) || + CHECK(sync))) + return -EINVAL; +#undef CHECK + + var->nonstd = 0; + var->accel_flags = 0; + + return 0; +} diff --git a/include/linux/amba/kmi.h b/include/linux/amba/kmi.h new file mode 100644 index 00000000..a39e5be7 --- /dev/null +++ b/include/linux/amba/kmi.h @@ -0,0 +1,92 @@ +/* + * linux/include/asm-arm/hardware/amba_kmi.h + * + * Internal header file for AMBA KMI ports + * + * Copyright (C) 2000 Deep Blue Solutions Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + * + * --------------------------------------------------------------------------- + * From ARM PrimeCell(tm) PS2 Keyboard/Mouse Interface (PL050) Technical + * Reference Manual - ARM DDI 0143B - see http://www.arm.com/ + * --------------------------------------------------------------------------- + */ +#ifndef ASM_ARM_HARDWARE_AMBA_KMI_H +#define ASM_ARM_HARDWARE_AMBA_KMI_H + +/* + * KMI control register: + * KMICR_TYPE 0 = PS2/AT mode, 1 = No line control bit mode + * KMICR_RXINTREN 1 = enable RX interrupts + * KMICR_TXINTREN 1 = enable TX interrupts + * KMICR_EN 1 = enable KMI + * KMICR_FD 1 = force KMI data low + * KMICR_FC 1 = force KMI clock low + */ +#define KMICR (KMI_BASE + 0x00) +#define KMICR_TYPE (1 << 5) +#define KMICR_RXINTREN (1 << 4) +#define KMICR_TXINTREN (1 << 3) +#define KMICR_EN (1 << 2) +#define KMICR_FD (1 << 1) +#define KMICR_FC (1 << 0) + +/* + * KMI status register: + * KMISTAT_TXEMPTY 1 = transmitter register empty + * KMISTAT_TXBUSY 1 = currently sending data + * KMISTAT_RXFULL 1 = receiver register ready to be read + * KMISTAT_RXBUSY 1 = currently receiving data + * KMISTAT_RXPARITY parity of last databyte received + * KMISTAT_IC current level of KMI clock input + * KMISTAT_ID current level of KMI data input + */ +#define KMISTAT (KMI_BASE + 0x04) +#define KMISTAT_TXEMPTY (1 << 6) +#define KMISTAT_TXBUSY (1 << 5) +#define KMISTAT_RXFULL (1 << 4) +#define KMISTAT_RXBUSY (1 << 3) +#define KMISTAT_RXPARITY (1 << 2) +#define KMISTAT_IC (1 << 1) +#define KMISTAT_ID (1 << 0) + +/* + * KMI data register + */ +#define KMIDATA (KMI_BASE + 0x08) + +/* + * KMI clock divisor: to generate 8MHz internal clock + * div = (ref / 8MHz) - 1; 0 <= div <= 15 + */ +#define KMICLKDIV (KMI_BASE + 0x0c) + +/* + * KMI interrupt register: + * KMIIR_TXINTR 1 = transmit interrupt asserted + * KMIIR_RXINTR 1 = receive interrupt asserted + */ +#define KMIIR (KMI_BASE + 0x10) +#define KMIIR_TXINTR (1 << 1) +#define KMIIR_RXINTR (1 << 0) + +/* + * The size of the KMI primecell + */ +#define KMI_SIZE (0x100) + +#endif diff --git a/include/linux/amba/mmci.h b/include/linux/amba/mmci.h new file mode 100644 index 00000000..9d1d9caf --- /dev/null +++ b/include/linux/amba/mmci.h @@ -0,0 +1,90 @@ +/* + * include/linux/amba/mmci.h + */ +#ifndef AMBA_MMCI_H +#define AMBA_MMCI_H + +#include <linux/mmc/host.h> +#include <linux/mmc/card.h> +#include <linux/mmc/sdio_func.h> + +struct embedded_sdio_data { + struct sdio_cis cis; + struct sdio_cccr cccr; + struct sdio_embedded_func *funcs; + int num_funcs; +}; + + +/* + * These defines is places here due to access is needed from machine + * configuration files. The ST Micro version does not have ROD and + * reuse the voltage registers for direction settings. + */ +#define MCI_ST_DATA2DIREN (1 << 2) +#define MCI_ST_CMDDIREN (1 << 3) +#define MCI_ST_DATA0DIREN (1 << 4) +#define MCI_ST_DATA31DIREN (1 << 5) +#define MCI_ST_FBCLKEN (1 << 7) +#define MCI_ST_DATA74DIREN (1 << 8) + +/* Just some dummy forwarding */ +struct dma_chan; + +/** + * struct mmci_platform_data - platform configuration for the MMCI + * (also known as PL180) block. + * @f_max: the maximum operational frequency for this host in this + * platform configuration. When this is specified it takes precedence + * over the module parameter for the same frequency. + * @ocr_mask: available voltages on the 4 pins from the block, this + * is ignored if a regulator is used, see the MMC_VDD_* masks in + * mmc/host.h + * @ios_handler: a callback function to act on specfic ios changes, + * used for example to control a levelshifter + * mask into a value to be binary (or set some other custom bits + * in MMCIPWR) or:ed and written into the MMCIPWR register of the + * block. May also control external power based on the power_mode. + * @status: if no GPIO read function was given to the block in + * gpio_wp (below) this function will be called to determine + * whether a card is present in the MMC slot or not + * @gpio_wp: read this GPIO pin to see if the card is write protected + * @gpio_cd: read this GPIO pin to detect card insertion + * @cd_invert: true if the gpio_cd pin value is active low + * @capabilities: the capabilities of the block as implemented in + * this platform, signify anything MMC_CAP_* from mmc/host.h + * @capabilities2: more capabilities, MMC_CAP2_* from mmc/host.h + * @sigdir: a bit field indicating for what bits in the MMC bus the host + * should enable signal direction indication. + * @dma_filter: function used to select an appropriate RX and TX + * DMA channel to be used for DMA, if and only if you're deploying the + * generic DMA engine + * @dma_rx_param: parameter passed to the DMA allocation + * filter in order to select an appropriate RX channel. If + * there is a bidirectional RX+TX channel, then just specify + * this and leave dma_tx_param set to NULL + * @dma_tx_param: parameter passed to the DMA allocation + * filter in order to select an appropriate TX channel. If this + * is NULL the driver will attempt to use the RX channel as a + * bidirectional channel + */ +struct mmci_platform_data { + unsigned int f_max; + unsigned int ocr_mask; + int (*ios_handler)(struct device *, struct mmc_ios *); + unsigned int (*status)(struct device *); + int gpio_wp; + int gpio_cd; + bool cd_invert; + unsigned long capabilities; + unsigned long capabilities2; + u32 sigdir; + bool (*dma_filter)(struct dma_chan *chan, void *filter_param); + void *dma_rx_param; + void *dma_tx_param; + unsigned int status_irq; + struct embedded_sdio_data *embedded_sdio; + int (*register_status_notify)(void (*callback)(int card_present, void *dev_id), void *dev_id); +}; + +#endif diff --git a/include/linux/amba/pl022.h b/include/linux/amba/pl022.h new file mode 100644 index 00000000..76dd1b19 --- /dev/null +++ b/include/linux/amba/pl022.h @@ -0,0 +1,300 @@ +/* + * include/linux/amba/pl022.h + * + * Copyright (C) 2008-2009 ST-Ericsson AB + * Copyright (C) 2006 STMicroelectronics Pvt. Ltd. + * + * Author: Linus Walleij <linus.walleij@stericsson.com> + * + * Initial version inspired by: + * linux-2.6.17-rc3-mm1/drivers/spi/pxa2xx_spi.c + * Initial adoption to PL022 by: + * Sachin Verma <sachin.verma@st.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef _SSP_PL022_H +#define _SSP_PL022_H + +#include <linux/types.h> + +/** + * whether SSP is in loopback mode or not + */ +enum ssp_loopback { + LOOPBACK_DISABLED, + LOOPBACK_ENABLED +}; + +/** + * enum ssp_interface - interfaces allowed for this SSP Controller + * @SSP_INTERFACE_MOTOROLA_SPI: Motorola Interface + * @SSP_INTERFACE_TI_SYNC_SERIAL: Texas Instrument Synchronous Serial + * interface + * @SSP_INTERFACE_NATIONAL_MICROWIRE: National Semiconductor Microwire + * interface + * @SSP_INTERFACE_UNIDIRECTIONAL: Unidirectional interface (STn8810 + * &STn8815 only) + */ +enum ssp_interface { + SSP_INTERFACE_MOTOROLA_SPI, + SSP_INTERFACE_TI_SYNC_SERIAL, + SSP_INTERFACE_NATIONAL_MICROWIRE, + SSP_INTERFACE_UNIDIRECTIONAL +}; + +/** + * enum ssp_hierarchy - whether SSP is configured as Master or Slave + */ +enum ssp_hierarchy { + SSP_MASTER, + SSP_SLAVE +}; + +/** + * enum ssp_clock_params - clock parameters, to set SSP clock at a + * desired freq + */ +struct ssp_clock_params { + u8 cpsdvsr; /* value from 2 to 254 (even only!) */ + u8 scr; /* value from 0 to 255 */ +}; + +/** + * enum ssp_rx_endian - endianess of Rx FIFO Data + * this feature is only available in ST versionf of PL022 + */ +enum ssp_rx_endian { + SSP_RX_MSB, + SSP_RX_LSB +}; + +/** + * enum ssp_tx_endian - endianess of Tx FIFO Data + */ +enum ssp_tx_endian { + SSP_TX_MSB, + SSP_TX_LSB +}; + +/** + * enum ssp_data_size - number of bits in one data element + */ +enum ssp_data_size { + SSP_DATA_BITS_4 = 0x03, SSP_DATA_BITS_5, SSP_DATA_BITS_6, + SSP_DATA_BITS_7, SSP_DATA_BITS_8, SSP_DATA_BITS_9, + SSP_DATA_BITS_10, SSP_DATA_BITS_11, SSP_DATA_BITS_12, + SSP_DATA_BITS_13, SSP_DATA_BITS_14, SSP_DATA_BITS_15, + SSP_DATA_BITS_16, SSP_DATA_BITS_17, SSP_DATA_BITS_18, + SSP_DATA_BITS_19, SSP_DATA_BITS_20, SSP_DATA_BITS_21, + SSP_DATA_BITS_22, SSP_DATA_BITS_23, SSP_DATA_BITS_24, + SSP_DATA_BITS_25, SSP_DATA_BITS_26, SSP_DATA_BITS_27, + SSP_DATA_BITS_28, SSP_DATA_BITS_29, SSP_DATA_BITS_30, + SSP_DATA_BITS_31, SSP_DATA_BITS_32 +}; + +/** + * enum ssp_mode - SSP mode of operation (Communication modes) + */ +enum ssp_mode { + INTERRUPT_TRANSFER, + POLLING_TRANSFER, + DMA_TRANSFER +}; + +/** + * enum ssp_rx_level_trig - receive FIFO watermark level which triggers + * IT: Interrupt fires when _N_ or more elements in RX FIFO. + */ +enum ssp_rx_level_trig { + SSP_RX_1_OR_MORE_ELEM, + SSP_RX_4_OR_MORE_ELEM, + SSP_RX_8_OR_MORE_ELEM, + SSP_RX_16_OR_MORE_ELEM, + SSP_RX_32_OR_MORE_ELEM +}; + +/** + * Transmit FIFO watermark level which triggers (IT Interrupt fires + * when _N_ or more empty locations in TX FIFO) + */ +enum ssp_tx_level_trig { + SSP_TX_1_OR_MORE_EMPTY_LOC, + SSP_TX_4_OR_MORE_EMPTY_LOC, + SSP_TX_8_OR_MORE_EMPTY_LOC, + SSP_TX_16_OR_MORE_EMPTY_LOC, + SSP_TX_32_OR_MORE_EMPTY_LOC +}; + +/** + * enum SPI Clock Phase - clock phase (Motorola SPI interface only) + * @SSP_CLK_FIRST_EDGE: Receive data on first edge transition (actual direction depends on polarity) + * @SSP_CLK_SECOND_EDGE: Receive data on second edge transition (actual direction depends on polarity) + */ +enum ssp_spi_clk_phase { + SSP_CLK_FIRST_EDGE, + SSP_CLK_SECOND_EDGE +}; + +/** + * enum SPI Clock Polarity - clock polarity (Motorola SPI interface only) + * @SSP_CLK_POL_IDLE_LOW: Low inactive level + * @SSP_CLK_POL_IDLE_HIGH: High inactive level + */ +enum ssp_spi_clk_pol { + SSP_CLK_POL_IDLE_LOW, + SSP_CLK_POL_IDLE_HIGH +}; + +/** + * Microwire Conrol Lengths Command size in microwire format + */ +enum ssp_microwire_ctrl_len { + SSP_BITS_4 = 0x03, SSP_BITS_5, SSP_BITS_6, + SSP_BITS_7, SSP_BITS_8, SSP_BITS_9, + SSP_BITS_10, SSP_BITS_11, SSP_BITS_12, + SSP_BITS_13, SSP_BITS_14, SSP_BITS_15, + SSP_BITS_16, SSP_BITS_17, SSP_BITS_18, + SSP_BITS_19, SSP_BITS_20, SSP_BITS_21, + SSP_BITS_22, SSP_BITS_23, SSP_BITS_24, + SSP_BITS_25, SSP_BITS_26, SSP_BITS_27, + SSP_BITS_28, SSP_BITS_29, SSP_BITS_30, + SSP_BITS_31, SSP_BITS_32 +}; + +/** + * enum Microwire Wait State + * @SSP_MWIRE_WAIT_ZERO: No wait state inserted after last command bit + * @SSP_MWIRE_WAIT_ONE: One wait state inserted after last command bit + */ +enum ssp_microwire_wait_state { + SSP_MWIRE_WAIT_ZERO, + SSP_MWIRE_WAIT_ONE +}; + +/** + * enum ssp_duplex - whether Full/Half Duplex on microwire, only + * available in the ST Micro variant. + * @SSP_MICROWIRE_CHANNEL_FULL_DUPLEX: SSPTXD becomes bi-directional, + * SSPRXD not used + * @SSP_MICROWIRE_CHANNEL_HALF_DUPLEX: SSPTXD is an output, SSPRXD is + * an input. + */ +enum ssp_duplex { + SSP_MICROWIRE_CHANNEL_FULL_DUPLEX, + SSP_MICROWIRE_CHANNEL_HALF_DUPLEX +}; + +/** + * enum ssp_clkdelay - an optional clock delay on the feedback clock + * only available in the ST Micro PL023 variant. + * @SSP_FEEDBACK_CLK_DELAY_NONE: no delay, the data coming in from the + * slave is sampled directly + * @SSP_FEEDBACK_CLK_DELAY_1T: the incoming slave data is sampled with + * a delay of T-dt + * @SSP_FEEDBACK_CLK_DELAY_2T: dito with a delay if 2T-dt + * @SSP_FEEDBACK_CLK_DELAY_3T: dito with a delay if 3T-dt + * @SSP_FEEDBACK_CLK_DELAY_4T: dito with a delay if 4T-dt + * @SSP_FEEDBACK_CLK_DELAY_5T: dito with a delay if 5T-dt + * @SSP_FEEDBACK_CLK_DELAY_6T: dito with a delay if 6T-dt + * @SSP_FEEDBACK_CLK_DELAY_7T: dito with a delay if 7T-dt + */ +enum ssp_clkdelay { + SSP_FEEDBACK_CLK_DELAY_NONE, + SSP_FEEDBACK_CLK_DELAY_1T, + SSP_FEEDBACK_CLK_DELAY_2T, + SSP_FEEDBACK_CLK_DELAY_3T, + SSP_FEEDBACK_CLK_DELAY_4T, + SSP_FEEDBACK_CLK_DELAY_5T, + SSP_FEEDBACK_CLK_DELAY_6T, + SSP_FEEDBACK_CLK_DELAY_7T +}; + +/** + * CHIP select/deselect commands + */ +enum ssp_chip_select { + SSP_CHIP_SELECT, + SSP_CHIP_DESELECT +}; + + +struct dma_chan; +/** + * struct pl022_ssp_master - device.platform_data for SPI controller devices. + * @num_chipselect: chipselects are used to distinguish individual + * SPI slaves, and are numbered from zero to num_chipselects - 1. + * each slave has a chipselect signal, but it's common that not + * every chipselect is connected to a slave. + * @enable_dma: if true enables DMA driven transfers. + * @dma_rx_param: parameter to locate an RX DMA channel. + * @dma_tx_param: parameter to locate a TX DMA channel. + * @autosuspend_delay: delay in ms following transfer completion before the + * runtime power management system suspends the device. A setting of 0 + * indicates no delay and the device will be suspended immediately. + * @rt: indicates the controller should run the message pump with realtime + * priority to minimise the transfer latency on the bus. + */ +struct pl022_ssp_controller { + u16 bus_id; + u8 num_chipselect; + u8 enable_dma:1; + bool (*dma_filter)(struct dma_chan *chan, void *filter_param); + void *dma_rx_param; + void *dma_tx_param; + int autosuspend_delay; + bool rt; +}; + +/** + * struct ssp_config_chip - spi_board_info.controller_data for SPI + * slave devices, copied to spi_device.controller_data. + * + * @lbm: used for test purpose to internally connect RX and TX + * @iface: Interface type(Motorola, TI, Microwire, Universal) + * @hierarchy: sets whether interface is master or slave + * @slave_tx_disable: SSPTXD is disconnected (in slave mode only) + * @clk_freq: Tune freq parameters of SSP(when in master mode) + * @endian_rx: Endianess of Data in Rx FIFO + * @endian_tx: Endianess of Data in Tx FIFO + * @data_size: Width of data element(4 to 32 bits) + * @com_mode: communication mode: polling, Interrupt or DMA + * @rx_lev_trig: Rx FIFO watermark level (for IT & DMA mode) + * @tx_lev_trig: Tx FIFO watermark level (for IT & DMA mode) + * @clk_phase: Motorola SPI interface Clock phase + * @clk_pol: Motorola SPI interface Clock polarity + * @ctrl_len: Microwire interface: Control length + * @wait_state: Microwire interface: Wait state + * @duplex: Microwire interface: Full/Half duplex + * @clkdelay: on the PL023 variant, the delay in feeback clock cycles + * before sampling the incoming line + * @cs_control: function pointer to board-specific function to + * assert/deassert I/O port to control HW generation of devices chip-select. + * @dma_xfer_type: Type of DMA xfer (Mem-to-periph or Periph-to-Periph) + * @dma_config: DMA configuration for SSP controller and peripheral + */ +struct pl022_config_chip { + enum ssp_interface iface; + enum ssp_hierarchy hierarchy; + bool slave_tx_disable; + struct ssp_clock_params clk_freq; + enum ssp_mode com_mode; + enum ssp_rx_level_trig rx_lev_trig; + enum ssp_tx_level_trig tx_lev_trig; + enum ssp_microwire_ctrl_len ctrl_len; + enum ssp_microwire_wait_state wait_state; + enum ssp_duplex duplex; + enum ssp_clkdelay clkdelay; + void (*cs_control) (u32 control); +}; + +#endif /* _SSP_PL022_H */ diff --git a/include/linux/amba/pl061.h b/include/linux/amba/pl061.h new file mode 100644 index 00000000..fb83c045 --- /dev/null +++ b/include/linux/amba/pl061.h @@ -0,0 +1,16 @@ +#include <linux/types.h> + +/* platform data for the PL061 GPIO driver */ + +struct pl061_platform_data { + /* number of the first GPIO */ + unsigned gpio_base; + + /* number of the first IRQ. + * If the IRQ functionality in not desired this must be set to 0. + */ + unsigned irq_base; + + u8 directions; /* startup directions, 1: out, 0: in */ + u8 values; /* startup values */ +}; diff --git a/include/linux/amba/pl08x.h b/include/linux/amba/pl08x.h new file mode 100644 index 00000000..e64ce2cf --- /dev/null +++ b/include/linux/amba/pl08x.h @@ -0,0 +1,244 @@ +/* + * linux/amba/pl08x.h - ARM PrimeCell DMA Controller driver + * + * Copyright (C) 2005 ARM Ltd + * Copyright (C) 2010 ST-Ericsson SA + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * pl08x information required by platform code + * + * Please credit ARM.com + * Documentation: ARM DDI 0196D + */ + +#ifndef AMBA_PL08X_H +#define AMBA_PL08X_H + +/* We need sizes of structs from this header */ +#include <linux/dmaengine.h> +#include <linux/interrupt.h> + +struct pl08x_lli; +struct pl08x_driver_data; + +/* Bitmasks for selecting AHB ports for DMA transfers */ +enum { + PL08X_AHB1 = (1 << 0), + PL08X_AHB2 = (1 << 1) +}; + +/** + * struct pl08x_channel_data - data structure to pass info between + * platform and PL08x driver regarding channel configuration + * @bus_id: name of this device channel, not just a device name since + * devices may have more than one channel e.g. "foo_tx" + * @min_signal: the minimum DMA signal number to be muxed in for this + * channel (for platforms supporting muxed signals). If you have + * static assignments, make sure this is set to the assigned signal + * number, PL08x have 16 possible signals in number 0 thru 15 so + * when these are not enough they often get muxed (in hardware) + * disabling simultaneous use of the same channel for two devices. + * @max_signal: the maximum DMA signal number to be muxed in for + * the channel. Set to the same as min_signal for + * devices with static assignments + * @muxval: a number usually used to poke into some mux regiser to + * mux in the signal to this channel + * @cctl_opt: default options for the channel control register + * @addr: source/target address in physical memory for this DMA channel, + * can be the address of a FIFO register for burst requests for example. + * This can be left undefined if the PrimeCell API is used for configuring + * this. + * @circular_buffer: whether the buffer passed in is circular and + * shall simply be looped round round (like a record baby round + * round round round) + * @single: the device connected to this channel will request single DMA + * transfers, not bursts. (Bursts are default.) + * @periph_buses: the device connected to this channel is accessible via + * these buses (use PL08X_AHB1 | PL08X_AHB2). + */ +struct pl08x_channel_data { + char *bus_id; + int min_signal; + int max_signal; + u32 muxval; + u32 cctl; + dma_addr_t addr; + bool circular_buffer; + bool single; + u8 periph_buses; +}; + +/** + * Struct pl08x_bus_data - information of source or destination + * busses for a transfer + * @addr: current address + * @maxwidth: the maximum width of a transfer on this bus + * @buswidth: the width of this bus in bytes: 1, 2 or 4 + */ +struct pl08x_bus_data { + dma_addr_t addr; + u8 maxwidth; + u8 buswidth; +}; + +/** + * struct pl08x_phy_chan - holder for the physical channels + * @id: physical index to this channel + * @lock: a lock to use when altering an instance of this struct + * @signal: the physical signal (aka channel) serving this physical channel + * right now + * @serving: the virtual channel currently being served by this physical + * channel + */ +struct pl08x_phy_chan { + unsigned int id; + void __iomem *base; + spinlock_t lock; + int signal; + struct pl08x_dma_chan *serving; +}; + +/** + * struct pl08x_sg - structure containing data per sg + * @src_addr: src address of sg + * @dst_addr: dst address of sg + * @len: transfer len in bytes + * @node: node for txd's dsg_list + */ +struct pl08x_sg { + dma_addr_t src_addr; + dma_addr_t dst_addr; + size_t len; + struct list_head node; +}; + +/** + * struct pl08x_txd - wrapper for struct dma_async_tx_descriptor + * @tx: async tx descriptor + * @node: node for txd list for channels + * @dsg_list: list of children sg's + * @direction: direction of transfer + * @llis_bus: DMA memory address (physical) start for the LLIs + * @llis_va: virtual memory address start for the LLIs + * @cctl: control reg values for current txd + * @ccfg: config reg values for current txd + */ +struct pl08x_txd { + struct dma_async_tx_descriptor tx; + struct list_head node; + struct list_head dsg_list; + enum dma_transfer_direction direction; + dma_addr_t llis_bus; + struct pl08x_lli *llis_va; + /* Default cctl value for LLIs */ + u32 cctl; + /* + * Settings to be put into the physical channel when we + * trigger this txd. Other registers are in llis_va[0]. + */ + u32 ccfg; +}; + +/** + * struct pl08x_dma_chan_state - holds the PL08x specific virtual channel + * states + * @PL08X_CHAN_IDLE: the channel is idle + * @PL08X_CHAN_RUNNING: the channel has allocated a physical transport + * channel and is running a transfer on it + * @PL08X_CHAN_PAUSED: the channel has allocated a physical transport + * channel, but the transfer is currently paused + * @PL08X_CHAN_WAITING: the channel is waiting for a physical transport + * channel to become available (only pertains to memcpy channels) + */ +enum pl08x_dma_chan_state { + PL08X_CHAN_IDLE, + PL08X_CHAN_RUNNING, + PL08X_CHAN_PAUSED, + PL08X_CHAN_WAITING, +}; + +/** + * struct pl08x_dma_chan - this structure wraps a DMA ENGINE channel + * @chan: wrappped abstract channel + * @phychan: the physical channel utilized by this channel, if there is one + * @phychan_hold: if non-zero, hold on to the physical channel even if we + * have no pending entries + * @tasklet: tasklet scheduled by the IRQ to handle actual work etc + * @name: name of channel + * @cd: channel platform data + * @runtime_addr: address for RX/TX according to the runtime config + * @runtime_direction: current direction of this channel according to + * runtime config + * @pend_list: queued transactions pending on this channel + * @at: active transaction on this channel + * @lock: a lock for this channel data + * @host: a pointer to the host (internal use) + * @state: whether the channel is idle, paused, running etc + * @slave: whether this channel is a device (slave) or for memcpy + * @device_fc: Flow Controller Settings for ccfg register. Only valid for slave + * channels. Fill with 'true' if peripheral should be flow controller. Direction + * will be selected at Runtime. + * @waiting: a TX descriptor on this channel which is waiting for a physical + * channel to become available + */ +struct pl08x_dma_chan { + struct dma_chan chan; + struct pl08x_phy_chan *phychan; + int phychan_hold; + struct tasklet_struct tasklet; + char *name; + const struct pl08x_channel_data *cd; + dma_addr_t src_addr; + dma_addr_t dst_addr; + u32 src_cctl; + u32 dst_cctl; + enum dma_transfer_direction runtime_direction; + struct list_head pend_list; + struct pl08x_txd *at; + spinlock_t lock; + struct pl08x_driver_data *host; + enum pl08x_dma_chan_state state; + bool slave; + bool device_fc; + struct pl08x_txd *waiting; +}; + +/** + * struct pl08x_platform_data - the platform configuration for the PL08x + * PrimeCells. + * @slave_channels: the channels defined for the different devices on the + * platform, all inclusive, including multiplexed channels. The available + * physical channels will be multiplexed around these signals as they are + * requested, just enumerate all possible channels. + * @get_signal: request a physical signal to be used for a DMA transfer + * immediately: if there is some multiplexing or similar blocking the use + * of the channel the transfer can be denied by returning less than zero, + * else it returns the allocated signal number + * @put_signal: indicate to the platform that this physical signal is not + * running any DMA transfer and multiplexing can be recycled + * @lli_buses: buses which LLIs can be fetched from: PL08X_AHB1 | PL08X_AHB2 + * @mem_buses: buses which memory can be accessed from: PL08X_AHB1 | PL08X_AHB2 + */ +struct pl08x_platform_data { + const struct pl08x_channel_data *slave_channels; + unsigned int num_slave_channels; + struct pl08x_channel_data memcpy_channel; + int (*get_signal)(struct pl08x_dma_chan *); + void (*put_signal)(struct pl08x_dma_chan *); + u8 lli_buses; + u8 mem_buses; +}; + +#ifdef CONFIG_AMBA_PL08X +bool pl08x_filter_id(struct dma_chan *chan, void *chan_id); +#else +static inline bool pl08x_filter_id(struct dma_chan *chan, void *chan_id) +{ + return false; +} +#endif + +#endif /* AMBA_PL08X_H */ diff --git a/include/linux/amba/pl093.h b/include/linux/amba/pl093.h new file mode 100644 index 00000000..2983e367 --- /dev/null +++ b/include/linux/amba/pl093.h @@ -0,0 +1,80 @@ +/* linux/amba/pl093.h + * + * Copyright (c) 2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * + * AMBA PL093 SSMC (synchronous static memory controller) + * See DDI0236.pdf (r0p4) for more details + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#define SMB_BANK(x) ((x) * 0x20) /* each bank control set is 0x20 apart */ + +/* Offsets for SMBxxxxRy registers */ + +#define SMBIDCYR (0x00) +#define SMBWSTRDR (0x04) +#define SMBWSTWRR (0x08) +#define SMBWSTOENR (0x0C) +#define SMBWSTWENR (0x10) +#define SMBCR (0x14) +#define SMBSR (0x18) +#define SMBWSTBRDR (0x1C) + +/* Masks for SMB registers */ +#define IDCY_MASK (0xf) +#define WSTRD_MASK (0xf) +#define WSTWR_MASK (0xf) +#define WSTOEN_MASK (0xf) +#define WSTWEN_MASK (0xf) + +/* Notes from datasheet: + * WSTOEN <= WSTRD + * WSTWEN <= WSTWR + * + * WSTOEN is not used with nWAIT + */ + +/* SMBCR bit definitions */ +#define SMBCR_BIWRITEEN (1 << 21) +#define SMBCR_ADDRVALIDWRITEEN (1 << 20) +#define SMBCR_SYNCWRITE (1 << 17) +#define SMBCR_BMWRITE (1 << 16) +#define SMBCR_WRAPREAD (1 << 14) +#define SMBCR_BIREADEN (1 << 13) +#define SMBCR_ADDRVALIDREADEN (1 << 12) +#define SMBCR_SYNCREAD (1 << 9) +#define SMBCR_BMREAD (1 << 8) +#define SMBCR_SMBLSPOL (1 << 6) +#define SMBCR_WP (1 << 3) +#define SMBCR_WAITEN (1 << 2) +#define SMBCR_WAITPOL (1 << 1) +#define SMBCR_RBLE (1 << 0) + +#define SMBCR_BURSTLENWRITE_MASK (3 << 18) +#define SMBCR_BURSTLENWRITE_4 (0 << 18) +#define SMBCR_BURSTLENWRITE_8 (1 << 18) +#define SMBCR_BURSTLENWRITE_RESERVED (2 << 18) +#define SMBCR_BURSTLENWRITE_CONTINUOUS (3 << 18) + +#define SMBCR_BURSTLENREAD_MASK (3 << 10) +#define SMBCR_BURSTLENREAD_4 (0 << 10) +#define SMBCR_BURSTLENREAD_8 (1 << 10) +#define SMBCR_BURSTLENREAD_16 (2 << 10) +#define SMBCR_BURSTLENREAD_CONTINUOUS (3 << 10) + +#define SMBCR_MW_MASK (3 << 4) +#define SMBCR_MW_8BIT (0 << 4) +#define SMBCR_MW_16BIT (1 << 4) +#define SMBCR_MW_M32BIT (2 << 4) + +/* SSMC status registers */ +#define SSMCCSR (0x200) +#define SSMCCR (0x204) +#define SSMCITCR (0x208) +#define SSMCITIP (0x20C) +#define SSMCITIOP (0x210) diff --git a/include/linux/amba/pl330.h b/include/linux/amba/pl330.h new file mode 100644 index 00000000..fe93758e --- /dev/null +++ b/include/linux/amba/pl330.h @@ -0,0 +1,35 @@ +/* linux/include/linux/amba/pl330.h + * + * Copyright (C) 2010 Samsung Electronics Co. Ltd. + * Jaswinder Singh <jassi.brar@samsung.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef __AMBA_PL330_H_ +#define __AMBA_PL330_H_ + +#include <linux/dmaengine.h> + +struct dma_pl330_platdata { + /* + * Number of valid peripherals connected to DMAC. + * This may be different from the value read from + * CR0, as the PL330 implementation might have 'holes' + * in the peri list or the peri could also be reached + * from another DMAC which the platform prefers. + */ + u8 nr_valid_peri; + /* Array of valid peripherals */ + u8 *peri_id; + /* Operational capabilities */ + dma_cap_mask_t cap_mask; + /* Bytes to allocate for MC buffer */ + unsigned mcbuf_sz; +}; + +extern bool pl330_filter(struct dma_chan *chan, void *param); +#endif /* __AMBA_PL330_H_ */ diff --git a/include/linux/amba/serial.h b/include/linux/amba/serial.h new file mode 100644 index 00000000..d117b29d --- /dev/null +++ b/include/linux/amba/serial.h @@ -0,0 +1,212 @@ +/* + * linux/include/asm-arm/hardware/serial_amba.h + * + * Internal header file for AMBA serial ports + * + * Copyright (C) ARM Limited + * Copyright (C) 2000 Deep Blue Solutions Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ +#ifndef ASM_ARM_HARDWARE_SERIAL_AMBA_H +#define ASM_ARM_HARDWARE_SERIAL_AMBA_H + +#include <linux/types.h> + +/* ------------------------------------------------------------------------------- + * From AMBA UART (PL010) Block Specification + * ------------------------------------------------------------------------------- + * UART Register Offsets. + */ +#define UART01x_DR 0x00 /* Data read or written from the interface. */ +#define UART01x_RSR 0x04 /* Receive status register (Read). */ +#define UART01x_ECR 0x04 /* Error clear register (Write). */ +#define UART010_LCRH 0x08 /* Line control register, high byte. */ +#define ST_UART011_DMAWM 0x08 /* DMA watermark configure register. */ +#define UART010_LCRM 0x0C /* Line control register, middle byte. */ +#define ST_UART011_TIMEOUT 0x0C /* Timeout period register. */ +#define UART010_LCRL 0x10 /* Line control register, low byte. */ +#define UART010_CR 0x14 /* Control register. */ +#define UART01x_FR 0x18 /* Flag register (Read only). */ +#define UART010_IIR 0x1C /* Interrupt indentification register (Read). */ +#define UART010_ICR 0x1C /* Interrupt clear register (Write). */ +#define ST_UART011_LCRH_RX 0x1C /* Rx line control register. */ +#define UART01x_ILPR 0x20 /* IrDA low power counter register. */ +#define UART011_IBRD 0x24 /* Integer baud rate divisor register. */ +#define UART011_FBRD 0x28 /* Fractional baud rate divisor register. */ +#define UART011_LCRH 0x2c /* Line control register. */ +#define ST_UART011_LCRH_TX 0x2c /* Tx Line control register. */ +#define UART011_CR 0x30 /* Control register. */ +#define UART011_IFLS 0x34 /* Interrupt fifo level select. */ +#define UART011_IMSC 0x38 /* Interrupt mask. */ +#define UART011_RIS 0x3c /* Raw interrupt status. */ +#define UART011_MIS 0x40 /* Masked interrupt status. */ +#define UART011_ICR 0x44 /* Interrupt clear register. */ +#define UART011_DMACR 0x48 /* DMA control register. */ +#define ST_UART011_XFCR 0x50 /* XON/XOFF control register. */ +#define ST_UART011_XON1 0x54 /* XON1 register. */ +#define ST_UART011_XON2 0x58 /* XON2 register. */ +#define ST_UART011_XOFF1 0x5C /* XON1 register. */ +#define ST_UART011_XOFF2 0x60 /* XON2 register. */ +#define ST_UART011_ITCR 0x80 /* Integration test control register. */ +#define ST_UART011_ITIP 0x84 /* Integration test input register. */ +#define ST_UART011_ABCR 0x100 /* Autobaud control register. */ +#define ST_UART011_ABIMSC 0x15C /* Autobaud interrupt mask/clear register. */ + +#define UART011_DR_OE (1 << 11) +#define UART011_DR_BE (1 << 10) +#define UART011_DR_PE (1 << 9) +#define UART011_DR_FE (1 << 8) + +#define UART01x_RSR_OE 0x08 +#define UART01x_RSR_BE 0x04 +#define UART01x_RSR_PE 0x02 +#define UART01x_RSR_FE 0x01 + +#define UART011_FR_RI 0x100 +#define UART011_FR_TXFE 0x080 +#define UART011_FR_RXFF 0x040 +#define UART01x_FR_TXFF 0x020 +#define UART01x_FR_RXFE 0x010 +#define UART01x_FR_BUSY 0x008 +#define UART01x_FR_DCD 0x004 +#define UART01x_FR_DSR 0x002 +#define UART01x_FR_CTS 0x001 +#define UART01x_FR_TMSK (UART01x_FR_TXFF + UART01x_FR_BUSY) + +#define UART011_CR_CTSEN 0x8000 /* CTS hardware flow control */ +#define UART011_CR_RTSEN 0x4000 /* RTS hardware flow control */ +#define UART011_CR_OUT2 0x2000 /* OUT2 */ +#define UART011_CR_OUT1 0x1000 /* OUT1 */ +#define UART011_CR_RTS 0x0800 /* RTS */ +#define UART011_CR_DTR 0x0400 /* DTR */ +#define UART011_CR_RXE 0x0200 /* receive enable */ +#define UART011_CR_TXE 0x0100 /* transmit enable */ +#define UART011_CR_LBE 0x0080 /* loopback enable */ +#define UART010_CR_RTIE 0x0040 +#define UART010_CR_TIE 0x0020 +#define UART010_CR_RIE 0x0010 +#define UART010_CR_MSIE 0x0008 +#define ST_UART011_CR_OVSFACT 0x0008 /* Oversampling factor */ +#define UART01x_CR_IIRLP 0x0004 /* SIR low power mode */ +#define UART01x_CR_SIREN 0x0002 /* SIR enable */ +#define UART01x_CR_UARTEN 0x0001 /* UART enable */ + +#define UART011_LCRH_SPS 0x80 +#define UART01x_LCRH_WLEN_8 0x60 +#define UART01x_LCRH_WLEN_7 0x40 +#define UART01x_LCRH_WLEN_6 0x20 +#define UART01x_LCRH_WLEN_5 0x00 +#define UART01x_LCRH_FEN 0x10 +#define UART01x_LCRH_STP2 0x08 +#define UART01x_LCRH_EPS 0x04 +#define UART01x_LCRH_PEN 0x02 +#define UART01x_LCRH_BRK 0x01 + +#define ST_UART011_DMAWM_RX_1 (0 << 3) +#define ST_UART011_DMAWM_RX_2 (1 << 3) +#define ST_UART011_DMAWM_RX_4 (2 << 3) +#define ST_UART011_DMAWM_RX_8 (3 << 3) +#define ST_UART011_DMAWM_RX_16 (4 << 3) +#define ST_UART011_DMAWM_RX_32 (5 << 3) +#define ST_UART011_DMAWM_RX_48 (6 << 3) +#define ST_UART011_DMAWM_TX_1 0 +#define ST_UART011_DMAWM_TX_2 1 +#define ST_UART011_DMAWM_TX_4 2 +#define ST_UART011_DMAWM_TX_8 3 +#define ST_UART011_DMAWM_TX_16 4 +#define ST_UART011_DMAWM_TX_32 5 +#define ST_UART011_DMAWM_TX_48 6 + +#define UART010_IIR_RTIS 0x08 +#define UART010_IIR_TIS 0x04 +#define UART010_IIR_RIS 0x02 +#define UART010_IIR_MIS 0x01 + +#define UART011_IFLS_RX1_8 (0 << 3) +#define UART011_IFLS_RX2_8 (1 << 3) +#define UART011_IFLS_RX4_8 (2 << 3) +#define UART011_IFLS_RX6_8 (3 << 3) +#define UART011_IFLS_RX7_8 (4 << 3) +#define UART011_IFLS_TX1_8 (0 << 0) +#define UART011_IFLS_TX2_8 (1 << 0) +#define UART011_IFLS_TX4_8 (2 << 0) +#define UART011_IFLS_TX6_8 (3 << 0) +#define UART011_IFLS_TX7_8 (4 << 0) +/* special values for ST vendor with deeper fifo */ +#define UART011_IFLS_RX_HALF (5 << 3) +#define UART011_IFLS_TX_HALF (5 << 0) + +#define UART011_OEIM (1 << 10) /* overrun error interrupt mask */ +#define UART011_BEIM (1 << 9) /* break error interrupt mask */ +#define UART011_PEIM (1 << 8) /* parity error interrupt mask */ +#define UART011_FEIM (1 << 7) /* framing error interrupt mask */ +#define UART011_RTIM (1 << 6) /* receive timeout interrupt mask */ +#define UART011_TXIM (1 << 5) /* transmit interrupt mask */ +#define UART011_RXIM (1 << 4) /* receive interrupt mask */ +#define UART011_DSRMIM (1 << 3) /* DSR interrupt mask */ +#define UART011_DCDMIM (1 << 2) /* DCD interrupt mask */ +#define UART011_CTSMIM (1 << 1) /* CTS interrupt mask */ +#define UART011_RIMIM (1 << 0) /* RI interrupt mask */ + +#define UART011_OEIS (1 << 10) /* overrun error interrupt status */ +#define UART011_BEIS (1 << 9) /* break error interrupt status */ +#define UART011_PEIS (1 << 8) /* parity error interrupt status */ +#define UART011_FEIS (1 << 7) /* framing error interrupt status */ +#define UART011_RTIS (1 << 6) /* receive timeout interrupt status */ +#define UART011_TXIS (1 << 5) /* transmit interrupt status */ +#define UART011_RXIS (1 << 4) /* receive interrupt status */ +#define UART011_DSRMIS (1 << 3) /* DSR interrupt status */ +#define UART011_DCDMIS (1 << 2) /* DCD interrupt status */ +#define UART011_CTSMIS (1 << 1) /* CTS interrupt status */ +#define UART011_RIMIS (1 << 0) /* RI interrupt status */ + +#define UART011_OEIC (1 << 10) /* overrun error interrupt clear */ +#define UART011_BEIC (1 << 9) /* break error interrupt clear */ +#define UART011_PEIC (1 << 8) /* parity error interrupt clear */ +#define UART011_FEIC (1 << 7) /* framing error interrupt clear */ +#define UART011_RTIC (1 << 6) /* receive timeout interrupt clear */ +#define UART011_TXIC (1 << 5) /* transmit interrupt clear */ +#define UART011_RXIC (1 << 4) /* receive interrupt clear */ +#define UART011_DSRMIC (1 << 3) /* DSR interrupt clear */ +#define UART011_DCDMIC (1 << 2) /* DCD interrupt clear */ +#define UART011_CTSMIC (1 << 1) /* CTS interrupt clear */ +#define UART011_RIMIC (1 << 0) /* RI interrupt clear */ + +#define UART011_DMAONERR (1 << 2) /* disable dma on error */ +#define UART011_TXDMAE (1 << 1) /* enable transmit dma */ +#define UART011_RXDMAE (1 << 0) /* enable receive dma */ + +#define UART01x_RSR_ANY (UART01x_RSR_OE|UART01x_RSR_BE|UART01x_RSR_PE|UART01x_RSR_FE) +#define UART01x_FR_MODEM_ANY (UART01x_FR_DCD|UART01x_FR_DSR|UART01x_FR_CTS) + +#ifndef __ASSEMBLY__ +struct amba_device; /* in uncompress this is included but amba/bus.h is not */ +struct amba_pl010_data { + void (*set_mctrl)(struct amba_device *dev, void __iomem *base, unsigned int mctrl); +}; + +struct dma_chan; +struct amba_pl011_data { + bool (*dma_filter)(struct dma_chan *chan, void *filter_param); + void *dma_rx_param; + void *dma_tx_param; + void (*init) (void); + void (*exit) (void); + void (*reset) (void); +}; +#endif + +#endif |