diff options
Diffstat (limited to 'drivers/mtd/maps/Kconfig')
| -rw-r--r-- | drivers/mtd/maps/Kconfig | 530 |
1 files changed, 530 insertions, 0 deletions
diff --git a/drivers/mtd/maps/Kconfig b/drivers/mtd/maps/Kconfig new file mode 100644 index 00000000..8af67cfd --- /dev/null +++ b/drivers/mtd/maps/Kconfig @@ -0,0 +1,530 @@ +menu "Mapping drivers for chip access" + depends on MTD!=n + depends on HAS_IOMEM + +config MTD_COMPLEX_MAPPINGS + bool "Support non-linear mappings of flash chips" + help + This causes the chip drivers to allow for complicated + paged mappings of flash chips. + +config MTD_PHYSMAP + tristate "Flash device in physical memory map" + depends on MTD_CFI || MTD_JEDECPROBE || MTD_ROM || MTD_LPDDR + help + This provides a 'mapping' driver which allows the NOR Flash and + ROM driver code to communicate with chips which are mapped + physically into the CPU's memory. You will need to configure + the physical address and size of the flash chips on your + particular board as well as the bus width, either statically + with config options or at run-time. + + To compile this driver as a module, choose M here: the + module will be called physmap. + +config MTD_PHYSMAP_COMPAT + bool "Physmap compat support" + depends on MTD_PHYSMAP + default n + help + Setup a simple mapping via the Kconfig options. Normally the + physmap configuration options are done via your board's + resource file. + + If unsure, say N here. + +config MTD_PHYSMAP_START + hex "Physical start address of flash mapping" + depends on MTD_PHYSMAP_COMPAT + default "0x8000000" + help + This is the physical memory location at which the flash chips + are mapped on your particular target board. Refer to the + memory map which should hopefully be in the documentation for + your board. + +config MTD_PHYSMAP_LEN + hex "Physical length of flash mapping" + depends on MTD_PHYSMAP_COMPAT + default "0" + help + This is the total length of the mapping of the flash chips on + your particular board. If there is space, or aliases, in the + physical memory map between the chips, this could be larger + than the total amount of flash present. Refer to the memory + map which should hopefully be in the documentation for your + board. + +config MTD_PHYSMAP_BANKWIDTH + int "Bank width in octets" + depends on MTD_PHYSMAP_COMPAT + default "2" + help + This is the total width of the data bus of the flash devices + in octets. For example, if you have a data bus width of 32 + bits, you would set the bus width octet value to 4. This is + used internally by the CFI drivers. + +config MTD_PHYSMAP_OF + tristate "Flash device in physical memory map based on OF description" + depends on OF && (MTD_CFI || MTD_JEDECPROBE || MTD_ROM) + help + This provides a 'mapping' driver which allows the NOR Flash and + ROM driver code to communicate with chips which are mapped + physically into the CPU's memory. The mapping description here is + taken from OF device tree. + +config MTD_PMC_MSP_EVM + tristate "CFI Flash device mapped on PMC-Sierra MSP" + depends on PMC_MSP && MTD_CFI + help + This provides a 'mapping' driver which supports the way + in which user-programmable flash chips are connected on the + PMC-Sierra MSP eval/demo boards. + +choice + prompt "Maximum mappable memory available for flash IO" + depends on MTD_PMC_MSP_EVM + default MSP_FLASH_MAP_LIMIT_32M + +config MSP_FLASH_MAP_LIMIT_32M + bool "32M" + +endchoice + +config MSP_FLASH_MAP_LIMIT + hex + default "0x02000000" + depends on MSP_FLASH_MAP_LIMIT_32M + +config MTD_SUN_UFLASH + tristate "Sun Microsystems userflash support" + depends on SPARC && MTD_CFI && PCI + help + This provides a 'mapping' driver which supports the way in + which user-programmable flash chips are connected on various + Sun Microsystems boardsets. This driver will require CFI support + in the kernel, so if you did not enable CFI previously, do that now. + +config MTD_SC520CDP + tristate "CFI Flash device mapped on AMD SC520 CDP" + depends on X86 && MTD_CFI + help + The SC520 CDP board has two banks of CFI-compliant chips and one + Dual-in-line JEDEC chip. This 'mapping' driver supports that + arrangement, implementing three MTD devices. + +config MTD_NETSC520 + tristate "CFI Flash device mapped on AMD NetSc520" + depends on X86 && MTD_CFI + help + This enables access routines for the flash chips on the AMD NetSc520 + demonstration board. If you have one of these boards and would like + to use the flash chips on it, say 'Y'. + +config MTD_TS5500 + tristate "JEDEC Flash device mapped on Technologic Systems TS-5500" + depends on X86 + select MTD_JEDECPROBE + select MTD_CFI_AMDSTD + help + This provides a driver for the on-board flash of the Technologic + System's TS-5500 board. The 2MB flash is split into 3 partitions + which are accessed as separate MTD devices. + + mtd0 and mtd2 are the two BIOS drives, which use the resident + flash disk (RFD) flash translation layer. + + mtd1 allows you to reprogram your BIOS. BE VERY CAREFUL. + + Note that jumper 3 ("Write Enable Drive A") must be set + otherwise detection won't succeed. + +config MTD_SBC_GXX + tristate "CFI Flash device mapped on Arcom SBC-GXx boards" + depends on X86 && MTD_CFI_INTELEXT && MTD_COMPLEX_MAPPINGS + help + This provides a driver for the on-board flash of Arcom Control + Systems' SBC-GXn family of boards, formerly known as SBC-MediaGX. + By default the flash is split into 3 partitions which are accessed + as separate MTD devices. This board utilizes Intel StrataFlash. + More info at + <http://www.arcomcontrols.com/products/icp/pc104/processors/SBC_GX1.htm>. + +config MTD_PXA2XX + tristate "CFI Flash device mapped on Intel XScale PXA2xx based boards" + depends on (PXA25x || PXA27x) && MTD_CFI_INTELEXT + help + This provides a driver for the NOR flash attached to a PXA2xx chip. + +config MTD_OCTAGON + tristate "JEDEC Flash device mapped on Octagon 5066 SBC" + depends on X86 && MTD_JEDEC && MTD_COMPLEX_MAPPINGS + help + This provides a 'mapping' driver which supports the way in which + the flash chips are connected in the Octagon-5066 Single Board + Computer. More information on the board is available at + <http://www.octagonsystems.com/products/5066.aspx>. + +config MTD_VMAX + tristate "JEDEC Flash device mapped on Tempustech VMAX SBC301" + depends on X86 && MTD_JEDEC && MTD_COMPLEX_MAPPINGS + help + This provides a 'mapping' driver which supports the way in which + the flash chips are connected in the Tempustech VMAX SBC301 Single + Board Computer. More information on the board is available at + <http://www.tempustech.com/>. + +config MTD_SCx200_DOCFLASH + tristate "Flash device mapped with DOCCS on NatSemi SCx200" + depends on SCx200 && MTD_CFI + help + Enable support for a flash chip mapped using the DOCCS signal on a + National Semiconductor SCx200 processor. + + If you don't know what to do here, say N. + + If compiled as a module, it will be called scx200_docflash. + +config MTD_AMD76XROM + tristate "BIOS flash chip on AMD76x southbridge" + depends on X86 && MTD_JEDECPROBE + help + Support for treating the BIOS flash chip on AMD76x motherboards + as an MTD device - with this you can reprogram your BIOS. + + BE VERY CAREFUL. + +config MTD_ICHXROM + tristate "BIOS flash chip on Intel Controller Hub 2/3/4/5" + depends on X86 && MTD_JEDECPROBE + help + Support for treating the BIOS flash chip on ICHX motherboards + as an MTD device - with this you can reprogram your BIOS. + + BE VERY CAREFUL. + +config MTD_ESB2ROM + tristate "BIOS flash chip on Intel ESB Controller Hub 2" + depends on X86 && MTD_JEDECPROBE && PCI + help + Support for treating the BIOS flash chip on ESB2 motherboards + as an MTD device - with this you can reprogram your BIOS. + + BE VERY CAREFUL. + +config MTD_CK804XROM + tristate "BIOS flash chip on Nvidia CK804" + depends on X86 && MTD_JEDECPROBE && PCI + help + Support for treating the BIOS flash chip on nvidia motherboards + as an MTD device - with this you can reprogram your BIOS. + + BE VERY CAREFUL. + +config MTD_SCB2_FLASH + tristate "BIOS flash chip on Intel SCB2 boards" + depends on X86 && MTD_JEDECPROBE + help + Support for treating the BIOS flash chip on Intel SCB2 boards + as an MTD device - with this you can reprogram your BIOS. + + BE VERY CAREFUL. + +config MTD_TSUNAMI + tristate "Flash chips on Tsunami TIG bus" + depends on ALPHA_TSUNAMI && MTD_COMPLEX_MAPPINGS + help + Support for the flash chip on Tsunami TIG bus. + +config MTD_NETtel + tristate "CFI flash device on SnapGear/SecureEdge" + depends on X86 && MTD_JEDECPROBE + help + Support for flash chips on NETtel/SecureEdge/SnapGear boards. + +config MTD_LANTIQ + tristate "Lantiq SoC NOR support" + depends on LANTIQ + help + Support for NOR flash attached to the Lantiq SoC's External Bus Unit. + +config MTD_DILNETPC + tristate "CFI Flash device mapped on DIL/Net PC" + depends on X86 && MTD_CFI_INTELEXT && BROKEN + help + MTD map driver for SSV DIL/Net PC Boards "DNP" and "ADNP". + For details, see <http://www.ssv-embedded.de/ssv/pc104/p169.htm> + and <http://www.ssv-embedded.de/ssv/pc104/p170.htm> + +config MTD_DILNETPC_BOOTSIZE + hex "Size of DIL/Net PC flash boot partition" + depends on MTD_DILNETPC + default "0x80000" + help + The amount of space taken up by the kernel or Etherboot + on the DIL/Net PC flash chips. + +config MTD_L440GX + tristate "BIOS flash chip on Intel L440GX boards" + depends on X86 && MTD_JEDECPROBE + help + Support for treating the BIOS flash chip on Intel L440GX motherboards + as an MTD device - with this you can reprogram your BIOS. + + BE VERY CAREFUL. + +config MTD_TQM8XXL + tristate "CFI Flash device mapped on TQM8XXL" + depends on MTD_CFI && TQM8xxL + help + The TQM8xxL PowerPC board has up to two banks of CFI-compliant + chips, currently uses AMD one. This 'mapping' driver supports + that arrangement, allowing the CFI probe and command set driver + code to communicate with the chips on the TQM8xxL board. More at + <http://www.denx.de/wiki/PPCEmbedded/>. + +config MTD_RPXLITE + tristate "CFI Flash device mapped on RPX Lite or CLLF" + depends on MTD_CFI && (RPXCLASSIC || RPXLITE) + help + The RPXLite PowerPC board has CFI-compliant chips mapped in + a strange sparse mapping. This 'mapping' driver supports that + arrangement, allowing the CFI probe and command set driver code + to communicate with the chips on the RPXLite board. More at + <http://www.embeddedplanet.com/>. + +config MTD_MBX860 + tristate "System flash on MBX860 board" + depends on MTD_CFI && MBX + help + This enables access routines for the flash chips on the Motorola + MBX860 board. If you have one of these boards and would like + to use the flash chips on it, say 'Y'. + +config MTD_DBOX2 + tristate "CFI Flash device mapped on D-Box2" + depends on DBOX2 && MTD_CFI_INTELSTD && MTD_CFI_INTELEXT && MTD_CFI_AMDSTD + help + This enables access routines for the flash chips on the Nokia/Sagem + D-Box 2 board. If you have one of these boards and would like to use + the flash chips on it, say 'Y'. + +config MTD_CFI_FLAGADM + tristate "CFI Flash device mapping on FlagaDM" + depends on 8xx && MTD_CFI + help + Mapping for the Flaga digital module. If you don't have one, ignore + this setting. + +config MTD_SOLUTIONENGINE + tristate "CFI Flash device mapped on Hitachi SolutionEngine" + depends on SUPERH && SOLUTION_ENGINE && MTD_CFI && MTD_REDBOOT_PARTS + help + This enables access to the flash chips on the Hitachi SolutionEngine and + similar boards. Say 'Y' if you are building a kernel for such a board. + +config MTD_CDB89712 + tristate "Cirrus CDB89712 evaluation board mappings" + depends on MTD_CFI && ARCH_CDB89712 + help + This enables access to the flash or ROM chips on the CDB89712 board. + If you have such a board, say 'Y'. + +config MTD_SA1100 + tristate "CFI Flash device mapped on StrongARM SA11x0" + depends on MTD_CFI && ARCH_SA1100 + help + This enables access to the flash chips on most platforms based on + the SA1100 and SA1110, including the Assabet and the Compaq iPAQ. + If you have such a board, say 'Y'. + +config MTD_DC21285 + tristate "CFI Flash device mapped on DC21285 Footbridge" + depends on MTD_CFI && ARCH_FOOTBRIDGE && MTD_COMPLEX_MAPPINGS + help + This provides a driver for the flash accessed using Intel's + 21285 bridge used with Intel's StrongARM processors. More info at + <http://www.intel.com/design/bridge/docs/21285_documentation.htm>. + +config MTD_IXP4XX + tristate "CFI Flash device mapped on Intel IXP4xx based systems" + depends on MTD_CFI && MTD_COMPLEX_MAPPINGS && ARCH_IXP4XX + help + This enables MTD access to flash devices on platforms based + on Intel's IXP4xx family of network processors such as the + IXDP425 and Coyote. If you have an IXP4xx based board and + would like to use the flash chips on it, say 'Y'. + +config MTD_IXP2000 + tristate "CFI Flash device mapped on Intel IXP2000 based systems" + depends on MTD_CFI && MTD_COMPLEX_MAPPINGS && ARCH_IXP2000 + help + This enables MTD access to flash devices on platforms based + on Intel's IXP2000 family of network processors. If you have an + IXP2000 based board and would like to use the flash chips on it, + say 'Y'. + +config MTD_FORTUNET + tristate "CFI Flash device mapped on the FortuNet board" + depends on MTD_CFI && SA1100_FORTUNET + help + This enables access to the Flash on the FortuNet board. If you + have such a board, say 'Y'. + +config MTD_AUTCPU12 + tristate "NV-RAM mapping AUTCPU12 board" + depends on ARCH_AUTCPU12 + help + This enables access to the NV-RAM on autronix autcpu12 board. + If you have such a board, say 'Y'. + +config MTD_IMPA7 + tristate "JEDEC Flash device mapped on impA7" + depends on ARM && MTD_JEDECPROBE + help + This enables access to the NOR Flash on the impA7 board of + implementa GmbH. If you have such a board, say 'Y' here. + +config MTD_H720X + tristate "Hynix evaluation board mappings" + depends on MTD_CFI && ( ARCH_H7201 || ARCH_H7202 ) + help + This enables access to the flash chips on the Hynix evaluation boards. + If you have such a board, say 'Y'. + +# This needs CFI or JEDEC, depending on the cards found. +config MTD_PCI + tristate "PCI MTD driver" + depends on PCI && MTD_COMPLEX_MAPPINGS + help + Mapping for accessing flash devices on add-in cards like the Intel XScale + IQ80310 card, and the Intel EBSA285 card in blank ROM programming mode + (please see the manual for the link settings). + + If you are not sure, say N. + +config MTD_PCMCIA + tristate "PCMCIA MTD driver" + depends on PCMCIA && MTD_COMPLEX_MAPPINGS + help + Map driver for accessing PCMCIA linear flash memory cards. These + cards are usually around 4-16MiB in size. This does not include + Compact Flash cards which are treated as IDE devices. + +config MTD_PCMCIA_ANONYMOUS + bool "Use PCMCIA MTD drivers for anonymous PCMCIA cards" + depends on MTD_PCMCIA + help + If this option is enabled, PCMCIA cards which do not report + anything about themselves are assumed to be MTD cards. + + If unsure, say N. + +config MTD_BFIN_ASYNC + tristate "Blackfin BF533-STAMP Flash Chip Support" + depends on BFIN533_STAMP && MTD_CFI && MTD_COMPLEX_MAPPINGS + default y + help + Map driver which allows for simultaneous utilization of + ethernet and CFI parallel flash. + + If compiled as a module, it will be called bfin-async-flash. + +config MTD_GPIO_ADDR + tristate "GPIO-assisted Flash Chip Support" + depends on GENERIC_GPIO || GPIOLIB + depends on MTD_COMPLEX_MAPPINGS + help + Map driver which allows flashes to be partially physically addressed + and assisted by GPIOs. + + If compiled as a module, it will be called gpio-addr-flash. + +config MTD_UCLINUX + bool "Generic uClinux RAM/ROM filesystem support" + depends on MTD_RAM=y && !MMU + help + Map driver to support image based filesystems for uClinux. + +config MTD_WRSBC8260 + tristate "Map driver for WindRiver PowerQUICC II MPC82xx board" + depends on (SBC82xx || SBC8560) + select MTD_MAP_BANK_WIDTH_4 + select MTD_MAP_BANK_WIDTH_1 + select MTD_CFI_I1 + select MTD_CFI_I4 + help + Map driver for WindRiver PowerQUICC II MPC82xx board. Drives + all three flash regions on CS0, CS1 and CS6 if they are configured + correctly by the boot loader. + +config MTD_DMV182 + tristate "Map driver for Dy-4 SVME/DMV-182 board." + depends on DMV182 + select MTD_MAP_BANK_WIDTH_32 + select MTD_CFI_I8 + select MTD_CFI_AMDSTD + help + Map driver for Dy-4 SVME/DMV-182 board. + +config MTD_INTEL_VR_NOR + tristate "NOR flash on Intel Vermilion Range Expansion Bus CS0" + depends on PCI + help + Map driver for a NOR flash bank located on the Expansion Bus of the + Intel Vermilion Range chipset. + +config MTD_RBTX4939 + tristate "Map driver for RBTX4939 board" + depends on TOSHIBA_RBTX4939 && MTD_CFI && MTD_COMPLEX_MAPPINGS + help + Map driver for NOR flash chips on RBTX4939 board. + +config MTD_PLATRAM + tristate "Map driver for platform device RAM (mtd-ram)" + select MTD_RAM + help + Map driver for RAM areas described via the platform device + system. + + This selection automatically selects the map_ram driver. + +config MTD_VMU + tristate "Map driver for Dreamcast VMU" + depends on MAPLE + help + This driver enables access to the Dreamcast Visual Memory Unit (VMU). + + Most Dreamcast users will want to say Y here. + + To build this as a module select M here, the module will be called + vmu-flash. + +config MTD_PISMO + tristate "MTD discovery driver for PISMO modules" + depends on I2C + depends on ARCH_VERSATILE + help + This driver allows for discovery of PISMO modules - see + <http://www.pismoworld.org/>. These are small modules containing + up to five memory devices (eg, SRAM, flash, DOC) described by an + I2C EEPROM. + + This driver does not create any MTD maps itself; instead it + creates MTD physmap and MTD SRAM platform devices. If you + enable this option, you should consider enabling MTD_PHYSMAP + and/or MTD_PLATRAM according to the devices on your module. + + When built as a module, it will be called pismo.ko + +config MTD_LATCH_ADDR + tristate "Latch-assisted Flash Chip Support" + depends on MTD_COMPLEX_MAPPINGS + help + Map driver which allows flashes to be partially physically addressed + and have the upper address lines set by a board specific code. + + If compiled as a module, it will be called latch-addr-flash. + +endmenu |