1 files changed, 207 insertions, 0 deletions
diff --git a/drivers/isdn/hisax/hfc_usb.h b/drivers/isdn/hisax/hfc_usb.h
new file mode 100644
index 00000000..f987bf89
--- /dev/null
+++ b/drivers/isdn/hisax/hfc_usb.h
@@ -0,0 +1,207 @@
+/*
+ * hfc_usb.h
+ *
+ * $Id: hfc_usb.h,v 1.1.2.5 2007/08/20 14:36:03 mbachem Exp $
+ */
+
+#ifndef __HFC_USB_H__
+#define __HFC_USB_H__
+
+#define DRIVER_AUTHOR   "Peter Sprenger (sprenger@moving-byters.de)"
+#define DRIVER_DESC     "HFC-S USB based HiSAX ISDN driver"
+
+
+#define HFC_CTRL_TIMEOUT	20	/* 5ms timeout writing/reading regs */
+#define HFC_TIMER_T3		8000	/* timeout for l1 activation timer */
+#define HFC_TIMER_T4		500	/* time for state change interval */
+
+#define HFCUSB_L1_STATECHANGE	0	/* L1 state changed */
+#define HFCUSB_L1_DRX		1	/* D-frame received */
+#define HFCUSB_L1_ERX		2	/* E-frame received */
+#define HFCUSB_L1_DTX		4	/* D-frames completed */
+
+#define MAX_BCH_SIZE		2048	/* allowed B-channel packet size */
+
+#define HFCUSB_RX_THRESHOLD	64	/* threshold for fifo report bit rx */
+#define HFCUSB_TX_THRESHOLD	64	/* threshold for fifo report bit tx */
+
+#define HFCUSB_CHIP_ID		0x16	/* Chip ID register index */
+#define HFCUSB_CIRM		0x00	/* cirm register index */
+#define HFCUSB_USB_SIZE		0x07	/* int length register */
+#define HFCUSB_USB_SIZE_I	0x06	/* iso length register */
+#define HFCUSB_F_CROSS		0x0b	/* bit order register */
+#define HFCUSB_CLKDEL		0x37	/* bit delay register */
+#define HFCUSB_CON_HDLC		0xfa	/* channel connect register */
+#define HFCUSB_HDLC_PAR		0xfb
+#define HFCUSB_SCTRL		0x31	/* S-bus control register (tx) */
+#define HFCUSB_SCTRL_E		0x32	/* same for E and special funcs */
+#define HFCUSB_SCTRL_R		0x33	/* S-bus control register (rx) */
+#define HFCUSB_F_THRES		0x0c	/* threshold register */
+#define HFCUSB_FIFO		0x0f	/* fifo select register */
+#define HFCUSB_F_USAGE		0x1a	/* fifo usage register */
+#define HFCUSB_MST_MODE0	0x14
+#define HFCUSB_MST_MODE1	0x15
+#define HFCUSB_P_DATA		0x1f
+#define HFCUSB_INC_RES_F	0x0e
+#define HFCUSB_STATES		0x30
+
+#define HFCUSB_CHIPID		0x40	/* ID value of HFC-S USB */
+
+
+/* fifo registers */
+#define HFCUSB_NUM_FIFOS	8	/* maximum number of fifos */
+#define HFCUSB_B1_TX		0	/* index for B1 transmit bulk/int */
+#define HFCUSB_B1_RX		1	/* index for B1 receive bulk/int */
+#define HFCUSB_B2_TX		2
+#define HFCUSB_B2_RX		3
+#define HFCUSB_D_TX		4
+#define HFCUSB_D_RX		5
+#define HFCUSB_PCM_TX		6
+#define HFCUSB_PCM_RX		7
+
+/*
+ * used to switch snd_transfer_mode for different TA modes e.g. the Billion USB TA just
+ * supports ISO out, while the Cologne Chip EVAL TA just supports BULK out
+ */
+#define USB_INT		0
+#define USB_BULK	1
+#define USB_ISOC	2
+
+#define ISOC_PACKETS_D	8
+#define ISOC_PACKETS_B	8
+#define ISO_BUFFER_SIZE	128
+
+/* Fifo flow Control for TX ISO */
+#define SINK_MAX	68
+#define SINK_MIN	48
+#define SINK_DMIN	12
+#define SINK_DMAX	18
+#define BITLINE_INF	(-64 * 8)
+
+/* HFC-S USB register access by Control-URSs */
+#define write_usb(a, b, c) usb_control_msg((a)->dev, (a)->ctrl_out_pipe, 0, 0x40, (c), (b), NULL, 0, HFC_CTRL_TIMEOUT)
+#define read_usb(a, b, c) usb_control_msg((a)->dev, (a)->ctrl_in_pipe, 1, 0xC0, 0, (b), (c), 1, HFC_CTRL_TIMEOUT)
+#define HFC_CTRL_BUFSIZE 32
+
+/* entry and size of output/input control buffer */
+typedef struct {
+	__u8 hfc_reg;		/* register number */
+	__u8 reg_val;		/* value to be written (or read) */
+	int action;		/* data for action handler */
+} ctrl_buft;
+
+/* Debugging Flags */
+#define HFCUSB_DBG_INIT		0x0001
+#define HFCUSB_DBG_STATES	0x0002
+#define HFCUSB_DBG_DCHANNEL	0x0080
+#define HFCUSB_DBG_FIFO_ERR	0x4000
+#define HFCUSB_DBG_VERBOSE_USB	0x8000
+
+/*
+ * URB error codes:
+ * Used to represent a list of values and their respective symbolic names
+ */
+struct hfcusb_symbolic_list {
+	const int num;
+	const char *name;
+};
+
+static struct hfcusb_symbolic_list urb_errlist[] = {
+	{-ENOMEM, "No memory for allocation of internal structures"},
+	{-ENOSPC, "The host controller's bandwidth is already consumed"},
+	{-ENOENT, "URB was canceled by unlink_urb"},
+	{-EXDEV, "ISO transfer only partially completed"},
+	{-EAGAIN, "Too match scheduled for the future"},
+	{-ENXIO, "URB already queued"},
+	{-EFBIG, "Too much ISO frames requested"},
+	{-ENOSR, "Buffer error (overrun)"},
+	{-EPIPE, "Specified endpoint is stalled (device not responding)"},
+	{-EOVERFLOW, "Babble (bad cable?)"},
+	{-EPROTO, "Bit-stuff error (bad cable?)"},
+	{-EILSEQ, "CRC/Timeout"},
+	{-ETIMEDOUT, "NAK (device does not respond)"},
+	{-ESHUTDOWN, "Device unplugged"},
+	{-1, NULL}
+};
+
+
+/*
+ * device dependent information to support different
+ * ISDN Ta's using the HFC-S USB chip
+ */
+
+/* USB descriptor need to contain one of the following EndPoint combination: */
+#define CNF_4INT3ISO	1	// 4 INT IN, 3 ISO OUT
+#define CNF_3INT3ISO	2	// 3 INT IN, 3 ISO OUT
+#define CNF_4ISO3ISO	3	// 4 ISO IN, 3 ISO OUT
+#define CNF_3ISO3ISO	4	// 3 ISO IN, 3 ISO OUT
+
+#define EP_NUL	1	// Endpoint at this position not allowed
+#define EP_NOP	2	// all type of endpoints allowed at this position
+#define EP_ISO	3	// Isochron endpoint mandatory at this position
+#define EP_BLK	4	// Bulk endpoint mandatory at this position
+#define EP_INT	5	// Interrupt endpoint mandatory at this position
+
+/*
+ * List of all supported endpoint configuration sets, used to find the
+ * best matching endpoint configuration within a devices' USB descriptor.
+ * We need at least 3 RX endpoints, and 3 TX endpoints, either
+ * INT-in and ISO-out, or ISO-in and ISO-out)
+ * with 4 RX endpoints even E-Channel logging is possible
+ */
+static int validconf[][19] = {
+	// INT in, ISO out config
+	{EP_NUL, EP_INT, EP_NUL, EP_INT, EP_NUL, EP_INT, EP_NOP, EP_INT,
+	 EP_ISO, EP_NUL, EP_ISO, EP_NUL, EP_ISO, EP_NUL, EP_NUL, EP_NUL,
+	 CNF_4INT3ISO, 2, 1},
+	{EP_NUL, EP_INT, EP_NUL, EP_INT, EP_NUL, EP_INT, EP_NUL, EP_NUL,
+	 EP_ISO, EP_NUL, EP_ISO, EP_NUL, EP_ISO, EP_NUL, EP_NUL, EP_NUL,
+	 CNF_3INT3ISO, 2, 0},
+	// ISO in, ISO out config
+	{EP_NUL, EP_NUL, EP_NUL, EP_NUL, EP_NUL, EP_NUL, EP_NUL, EP_NUL,
+	 EP_ISO, EP_ISO, EP_ISO, EP_ISO, EP_ISO, EP_ISO, EP_NOP, EP_ISO,
+	 CNF_4ISO3ISO, 2, 1},
+	{EP_NUL, EP_NUL, EP_NUL, EP_NUL, EP_NUL, EP_NUL, EP_NUL, EP_NUL,
+	 EP_ISO, EP_ISO, EP_ISO, EP_ISO, EP_ISO, EP_ISO, EP_NUL, EP_NUL,
+	 CNF_3ISO3ISO, 2, 0},
+	{0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}	// EOL element
+};
+
+#ifdef CONFIG_HISAX_DEBUG
+// string description of chosen config
+static char *conf_str[] = {
+	"4 Interrupt IN + 3 Isochron OUT",
+	"3 Interrupt IN + 3 Isochron OUT",
+	"4 Isochron IN + 3 Isochron OUT",
+	"3 Isochron IN + 3 Isochron OUT"
+};
+#endif
+
+typedef struct {
+	int vendor;		// vendor id
+	int prod_id;		// product id
+	char *vend_name;	// vendor string
+	__u8 led_scheme;	// led display scheme
+	signed short led_bits[8];	// array of 8 possible LED bitmask settings
+} vendor_data;
+
+#define LED_OFF		0	// no LED support
+#define LED_SCHEME1	1	// LED standard scheme
+#define LED_SCHEME2	2	// not used yet...
+
+#define LED_POWER_ON	1
+#define LED_POWER_OFF	2
+#define LED_S0_ON	3
+#define LED_S0_OFF	4
+#define LED_B1_ON	5
+#define LED_B1_OFF	6
+#define LED_B1_DATA	7
+#define LED_B2_ON	8
+#define LED_B2_OFF	9
+#define LED_B2_DATA	10
+
+#define LED_NORMAL	0	// LEDs are normal
+#define LED_INVERTED	1	// LEDs are inverted
+
+
+#endif	// __HFC_USB_H__