diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
222 files changed, 10243 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/arm/arm-boards b/Documentation/devicetree/bindings/arm/arm-boards new file mode 100644 index 00000000..91f26148 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/arm-boards @@ -0,0 +1,20 @@ +ARM Versatile Application and Platform Baseboards +------------------------------------------------- +ARM's development hardware platform with connectors for customizable +core tiles. The hardware configuration of the Versatile boards is +highly customizable. + +Required properties (in root node): + compatible = "arm,versatile-ab"; /* Application baseboard */ + compatible = "arm,versatile-pb"; /* Platform baseboard */ + +Interrupt controllers: +- VIC required properties: + compatible = "arm,versatile-vic"; + interrupt-controller; + #interrupt-cells = <1>; + +- SIC required properties: + compatible = "arm,versatile-sic"; + interrupt-controller; + #interrupt-cells = <1>; diff --git a/Documentation/devicetree/bindings/arm/atmel-aic.txt b/Documentation/devicetree/bindings/arm/atmel-aic.txt new file mode 100644 index 00000000..aabca4f8 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/atmel-aic.txt @@ -0,0 +1,38 @@ +* Advanced Interrupt Controller (AIC) + +Required properties: +- compatible: Should be "atmel,<chip>-aic" +- interrupt-controller: Identifies the node as an interrupt controller. +- interrupt-parent: For single AIC system, it is an empty property. +- #interrupt-cells: The number of cells to define the interrupts. It sould be 2. + The first cell is the IRQ number (aka "Peripheral IDentifier" on datasheet). + The second cell is used to specify flags: + bits[3:0] trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. + Valid combinations are 1, 2, 3, 4, 8. + Default flag for internal sources should be set to 4 (active high). +- reg: Should contain AIC registers location and length + +Examples: + /* + * AIC + */ + aic: interrupt-controller@fffff000 { + compatible = "atmel,at91rm9200-aic"; + interrupt-controller; + interrupt-parent; + #interrupt-cells = <2>; + reg = <0xfffff000 0x200>; + }; + + /* + * An interrupt generating device that is wired to an AIC. + */ + dma: dma-controller@ffffec00 { + compatible = "atmel,at91sam9g45-dma"; + reg = <0xffffec00 0x200>; + interrupts = <21 4>; + }; diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt new file mode 100644 index 00000000..ecc81e36 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt @@ -0,0 +1,92 @@ +Atmel AT91 device tree bindings. +================================ + +PIT Timer required properties: +- compatible: Should be "atmel,at91sam9260-pit" +- reg: Should contain registers location and length +- interrupts: Should contain interrupt for the PIT which is the IRQ line + shared across all System Controller members. + +TC/TCLIB Timer required properties: +- compatible: Should be "atmel,<chip>-pit". + <chip> can be "at91rm9200" or "at91sam9x5" +- reg: Should contain registers location and length +- interrupts: Should contain all interrupts for the TC block + Note that you can specify several interrupt cells if the TC + block has one interrupt per channel. + +Examples: + +One interrupt per TC block: + tcb0: timer@fff7c000 { + compatible = "atmel,at91rm9200-tcb"; + reg = <0xfff7c000 0x100>; + interrupts = <18 4>; + }; + +One interrupt per TC channel in a TC block: + tcb1: timer@fffdc000 { + compatible = "atmel,at91rm9200-tcb"; + reg = <0xfffdc000 0x100>; + interrupts = <26 4 27 4 28 4>; + }; + +RSTC Reset Controller required properties: +- compatible: Should be "atmel,<chip>-rstc". + <chip> can be "at91sam9260" or "at91sam9g45" +- reg: Should contain registers location and length + +Example: + + rstc@fffffd00 { + compatible = "atmel,at91sam9260-rstc"; + reg = <0xfffffd00 0x10>; + }; + +RAMC SDRAM/DDR Controller required properties: +- compatible: Should be "atmel,at91sam9260-sdramc", + "atmel,at91sam9g45-ddramc", +- reg: Should contain registers location and length + For at91sam9263 and at91sam9g45 you must specify 2 entries. + +Examples: + + ramc0: ramc@ffffe800 { + compatible = "atmel,at91sam9g45-ddramc"; + reg = <0xffffe800 0x200>; + }; + + ramc0: ramc@ffffe400 { + compatible = "atmel,at91sam9g45-ddramc"; + reg = <0xffffe400 0x200 + 0xffffe600 0x200>; + }; + +SHDWC Shutdown Controller + +required properties: +- compatible: Should be "atmel,<chip>-shdwc". + <chip> can be "at91sam9260", "at91sam9rl" or "at91sam9x5". +- reg: Should contain registers location and length + +optional properties: +- atmel,wakeup-mode: String, operation mode of the wakeup mode. + Supported values are: "none", "high", "low", "any". +- atmel,wakeup-counter: Counter on Wake-up 0 (between 0x0 and 0xf). + +optional at91sam9260 properties: +- atmel,wakeup-rtt-timer: boolean to enable Real-time Timer Wake-up. + +optional at91sam9rl properties: +- atmel,wakeup-rtc-timer: boolean to enable Real-time Clock Wake-up. +- atmel,wakeup-rtt-timer: boolean to enable Real-time Timer Wake-up. + +optional at91sam9x5 properties: +- atmel,wakeup-rtc-timer: boolean to enable Real-time Clock Wake-up. + +Example: + + rstc@fffffd00 { + compatible = "atmel,at91sam9260-rstc"; + reg = <0xfffffd00 0x10>; + }; diff --git a/Documentation/devicetree/bindings/arm/atmel-pmc.txt b/Documentation/devicetree/bindings/arm/atmel-pmc.txt new file mode 100644 index 00000000..389bed50 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/atmel-pmc.txt @@ -0,0 +1,11 @@ +* Power Management Controller (PMC) + +Required properties: +- compatible: Should be "atmel,at91rm9200-pmc" +- reg: Should contain PMC registers location and length + +Examples: + pmc: pmc@fffffc00 { + compatible = "atmel,at91rm9200-pmc"; + reg = <0xfffffc00 0x100>; + }; diff --git a/Documentation/devicetree/bindings/arm/calxeda.txt b/Documentation/devicetree/bindings/arm/calxeda.txt new file mode 100644 index 00000000..4755caac --- /dev/null +++ b/Documentation/devicetree/bindings/arm/calxeda.txt @@ -0,0 +1,8 @@ +Calxeda Highbank Platforms Device Tree Bindings +----------------------------------------------- + +Boards with Calxeda Cortex-A9 based Highbank SOC shall have the following +properties. + +Required root node properties: + - compatible = "calxeda,highbank"; diff --git a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt new file mode 100644 index 00000000..6528e215 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt @@ -0,0 +1,21 @@ +* Samsung Exynos Power Domains + +Exynos processors include support for multiple power domains which are used +to gate power to one or more peripherals on the processor. + +Required Properties: +- compatiable: should be one of the following. + * samsung,exynos4210-pd - for exynos4210 type power domain. +- reg: physical base address of the controller and length of memory mapped + region. + +Optional Properties: +- samsung,exynos4210-pd-off: Specifies that the power domain is in turned-off + state during boot and remains to be turned-off until explicitly turned-on. + +Example: + + lcd0: power-domain-lcd0 { + compatible = "samsung,exynos4210-pd"; + reg = <0x10023C00 0x10>; + }; diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt new file mode 100644 index 00000000..bfbc771a --- /dev/null +++ b/Documentation/devicetree/bindings/arm/fsl.txt @@ -0,0 +1,52 @@ +Freescale i.MX Platforms Device Tree Bindings +----------------------------------------------- + +i.MX51 Babbage Board +Required root node properties: + - compatible = "fsl,imx51-babbage", "fsl,imx51"; + +i.MX53 Automotive Reference Design Board +Required root node properties: + - compatible = "fsl,imx53-ard", "fsl,imx53"; + +i.MX53 Evaluation Kit +Required root node properties: + - compatible = "fsl,imx53-evk", "fsl,imx53"; + +i.MX53 Quick Start Board +Required root node properties: + - compatible = "fsl,imx53-qsb", "fsl,imx53"; + +i.MX53 Smart Mobile Reference Design Board +Required root node properties: + - compatible = "fsl,imx53-smd", "fsl,imx53"; + +i.MX6 Quad Armadillo2 Board +Required root node properties: + - compatible = "fsl,imx6q-arm2", "fsl,imx6q"; + +i.MX6 Quad SABRE Lite Board +Required root node properties: + - compatible = "fsl,imx6q-sabrelite", "fsl,imx6q"; + +Generic i.MX boards +------------------- + +No iomux setup is done for these boards, so this must have been configured +by the bootloader for boards to work with the generic bindings. + +i.MX27 generic board +Required root node properties: + - compatible = "fsl,imx27"; + +i.MX51 generic board +Required root node properties: + - compatible = "fsl,imx51"; + +i.MX53 generic board +Required root node properties: + - compatible = "fsl,imx53"; + +i.MX6q generic board +Required root node properties: + - compatible = "fsl,imx6q"; diff --git a/Documentation/devicetree/bindings/arm/gic.txt b/Documentation/devicetree/bindings/arm/gic.txt new file mode 100644 index 00000000..9b4b82a7 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/gic.txt @@ -0,0 +1,59 @@ +* ARM Generic Interrupt Controller + +ARM SMP cores are often associated with a GIC, providing per processor +interrupts (PPI), shared processor interrupts (SPI) and software +generated interrupts (SGI). + +Primary GIC is attached directly to the CPU and typically has PPIs and SGIs. +Secondary GICs are cascaded into the upward interrupt controller and do not +have PPIs or SGIs. + +Main node required properties: + +- compatible : should be one of: + "arm,cortex-a9-gic" + "arm,arm11mp-gic" +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The type shall be a <u32> and the value shall be 3. + + The 1st cell is the interrupt type; 0 for SPI interrupts, 1 for PPI + interrupts. + + The 2nd cell contains the interrupt number for the interrupt type. + SPI interrupts are in the range [0-987]. PPI interrupts are in the + range [0-15]. + + The 3rd cell is the flags, encoded as follows: + bits[3:0] trigger type and level flags. + 1 = low-to-high edge triggered + 2 = high-to-low edge triggered + 4 = active high level-sensitive + 8 = active low level-sensitive + bits[15:8] PPI interrupt cpu mask. Each bit corresponds to each of + the 8 possible cpus attached to the GIC. A bit set to '1' indicated + the interrupt is wired to that CPU. Only valid for PPI interrupts. + +- reg : Specifies base physical address(s) and size of the GIC registers. The + first region is the GIC distributor register base and size. The 2nd region is + the GIC cpu interface register base and size. + +Optional +- interrupts : Interrupt source of the parent interrupt controller. Only + present on secondary GICs. + +- cpu-offset : per-cpu offset within the distributor and cpu interface + regions, used when the GIC doesn't have banked registers. The offset is + cpu-offset * cpu-nr. + +Example: + + intc: interrupt-controller@fff11000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + #address-cells = <1>; + interrupt-controller; + reg = <0xfff11000 0x1000>, + <0xfff10100 0x100>; + }; + diff --git a/Documentation/devicetree/bindings/arm/insignal-boards.txt b/Documentation/devicetree/bindings/arm/insignal-boards.txt new file mode 100644 index 00000000..524c3dc5 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/insignal-boards.txt @@ -0,0 +1,8 @@ +* Insignal's Exynos4210 based Origen evaluation board + +Origen low-cost evaluation board is based on Samsung's Exynos4210 SoC. + +Required root node properties: + - compatible = should be one or more of the following. + (a) "samsung,smdkv310" - for Samsung's SMDKV310 eval board. + (b) "samsung,exynos4210" - for boards based on Exynos4210 SoC. diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt new file mode 100644 index 00000000..7ca52161 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/l2cc.txt @@ -0,0 +1,44 @@ +* ARM L2 Cache Controller + +ARM cores often have a separate level 2 cache controller. There are various +implementations of the L2 cache controller with compatible programming models. +The ARM L2 cache representation in the device tree should be done as follows: + +Required properties: + +- compatible : should be one of: + "arm,pl310-cache" + "arm,l220-cache" + "arm,l210-cache" +- cache-unified : Specifies the cache is a unified cache. +- cache-level : Should be set to 2 for a level 2 cache. +- reg : Physical base address and size of cache controller's memory mapped + registers. + +Optional properties: + +- arm,data-latency : Cycles of latency for Data RAM accesses. Specifies 3 cells of + read, write and setup latencies. Minimum valid values are 1. Controllers + without setup latency control should use a value of 0. +- arm,tag-latency : Cycles of latency for Tag RAM accesses. Specifies 3 cells of + read, write and setup latencies. Controllers without setup latency control + should use 0. Controllers without separate read and write Tag RAM latency + values should only use the first cell. +- arm,dirty-latency : Cycles of latency for Dirty RAMs. This is a single cell. +- arm,filter-ranges : <start length> Starting address and length of window to + filter. Addresses in the filter window are directed to the M1 port. Other + addresses will go to the M0 port. +- interrupts : 1 combined interrupt. + +Example: + +L2: cache-controller { + compatible = "arm,pl310-cache"; + reg = <0xfff12000 0x1000>; + arm,data-latency = <1 1 1>; + arm,tag-latency = <2 2 2>; + arm,filter-latency = <0x80000000 0x8000000>; + cache-unified; + cache-level = <2>; + interrupts = <45>; +}; diff --git a/Documentation/devicetree/bindings/arm/mrvl.txt b/Documentation/devicetree/bindings/arm/mrvl.txt new file mode 100644 index 00000000..d8de933e --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mrvl.txt @@ -0,0 +1,6 @@ +Marvell Platforms Device Tree Bindings +---------------------------------------------------- + +PXA168 Aspenite Board +Required root node properties: + - compatible = "mrvl,pxa168-aspenite", "mrvl,pxa168"; diff --git a/Documentation/devicetree/bindings/arm/omap/dsp.txt b/Documentation/devicetree/bindings/arm/omap/dsp.txt new file mode 100644 index 00000000..d3830a32 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/dsp.txt @@ -0,0 +1,14 @@ +* TI - DSP (Digital Signal Processor) + +TI DSP included in OMAP SoC + +Required properties: +- compatible : Should be "ti,omap3-c64" for OMAP3 & 4 +- ti,hwmods: "dsp" + +Examples: + +dsp { + compatible = "ti,omap3-c64"; + ti,hwmods = "dsp"; +}; diff --git a/Documentation/devicetree/bindings/arm/omap/intc.txt b/Documentation/devicetree/bindings/arm/omap/intc.txt new file mode 100644 index 00000000..f2583e6e --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/intc.txt @@ -0,0 +1,27 @@ +* OMAP Interrupt Controller + +OMAP2/3 are using a TI interrupt controller that can support several +configurable number of interrupts. + +Main node required properties: + +- compatible : should be: + "ti,omap2-intc" +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The type shall be a <u32> and the value shall be 1. + + The cell contains the interrupt number in the range [0-128]. +- ti,intc-size: Number of interrupts handled by the interrupt controller. +- reg: physical base address and size of the intc registers map. + +Example: + + intc: interrupt-controller@1 { + compatible = "ti,omap2-intc"; + interrupt-controller; + #interrupt-cells = <1>; + ti,intc-size = <96>; + reg = <0x48200000 0x1000>; + }; + diff --git a/Documentation/devicetree/bindings/arm/omap/iva.txt b/Documentation/devicetree/bindings/arm/omap/iva.txt new file mode 100644 index 00000000..6d629517 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/iva.txt @@ -0,0 +1,19 @@ +* TI - IVA (Imaging and Video Accelerator) subsystem + +The IVA contain various audio, video or imaging HW accelerator +depending of the version. + +Required properties: +- compatible : Should be: + - "ti,ivahd" for OMAP4 + - "ti,iva2.2" for OMAP3 + - "ti,iva2.1" for OMAP2430 + - "ti,iva1" for OMAP2420 +- ti,hwmods: "iva" + +Examples: + +iva { + compatible = "ti,ivahd", "ti,iva"; + ti,hwmods = "iva"; +}; diff --git a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt new file mode 100644 index 00000000..6888a5ef --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt @@ -0,0 +1,19 @@ +* TI - L3 Network On Chip (NoC) + +This version is an implementation of the generic NoC IP +provided by Arteris. + +Required properties: +- compatible : Should be "ti,omap3-l3-smx" for OMAP3 family + Should be "ti,omap4-l3-noc" for OMAP4 family +- ti,hwmods: "l3_main_1", ... One hwmod for each noc domain. + +Examples: + +ocp { + compatible = "ti,omap4-l3-noc", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3"; +}; diff --git a/Documentation/devicetree/bindings/arm/omap/mpu.txt b/Documentation/devicetree/bindings/arm/omap/mpu.txt new file mode 100644 index 00000000..1a5a42ce --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/mpu.txt @@ -0,0 +1,27 @@ +* TI - MPU (Main Processor Unit) subsystem + +The MPU subsystem contain one or several ARM cores +depending of the version. +The MPU contain CPUs, GIC, L2 cache and a local PRCM. + +Required properties: +- compatible : Should be "ti,omap3-mpu" for OMAP3 + Should be "ti,omap4-mpu" for OMAP4 +- ti,hwmods: "mpu" + +Examples: + +- For an OMAP4 SMP system: + +mpu { + compatible = "ti,omap4-mpu"; + ti,hwmods = "mpu"; +}; + + +- For an OMAP3 monocore system: + +mpu { + compatible = "ti,omap3-mpu"; + ti,hwmods = "mpu"; +}; diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt new file mode 100644 index 00000000..e78e8bcc --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -0,0 +1,49 @@ +* Texas Instruments OMAP + +OMAP is currently using a static file per SoC family to describe the +IPs present in the SoC. +On top of that an omap_device is created to extend the platform_device +capabilities and to allow binding with one or several hwmods. +The hwmods will contain all the information to build the device: +address range, irq lines, dma lines, interconnect, PRCM register, +clock domain, input clocks. +For the moment just point to the existing hwmod, the next step will be +to move data from hwmod to device-tree representation. + + +Required properties: +- compatible: Every devices present in OMAP SoC should be in the + form: "ti,XXX" +- ti,hwmods: list of hwmod names (ascii strings), that comes from the OMAP + HW documentation, attached to a device. Must contain at least + one hwmod. + +Optional properties: +- ti,no_idle_on_suspend: When present, it prevents the PM to idle the module + during suspend. + + +Example: + +spinlock@1 { + compatible = "ti,omap4-spinlock"; + ti,hwmods = "spinlock"; +}; + + +Boards: + +- OMAP3 BeagleBoard : Low cost community board + compatible = "ti,omap3-beagle", "ti,omap3" + +- OMAP4 SDP : Software Developement Board + compatible = "ti,omap4-sdp", "ti,omap4430" + +- OMAP4 PandaBoard : Low cost community board + compatible = "ti,omap4-panda", "ti,omap4430" + +- OMAP3 EVM : Software Developement Board for OMAP35x, AM/DM37x + compatible = "ti,omap3-evm", "ti,omap3" + +- AM335X EVM : Software Developement Board for AM335x + compatible = "ti,am335x-evm", "ti,am33xx", "ti,omap3" diff --git a/Documentation/devicetree/bindings/arm/picoxcell.txt b/Documentation/devicetree/bindings/arm/picoxcell.txt new file mode 100644 index 00000000..e75c0ef5 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/picoxcell.txt @@ -0,0 +1,24 @@ +Picochip picoXcell device tree bindings. +======================================== + +Required root node properties: + - compatible: + - "picochip,pc7302-pc3x3" : PC7302 development board with PC3X3 device. + - "picochip,pc7302-pc3x2" : PC7302 development board with PC3X2 device. + - "picochip,pc3x3" : picoXcell PC3X3 device based board. + - "picochip,pc3x2" : picoXcell PC3X2 device based board. + +Timers required properties: + - compatible = "picochip,pc3x2-timer" + - interrupts : The single IRQ line for the timer. + - clock-freq : The frequency in HZ of the timer. + - reg : The register bank for the timer. + +Note: two timers are required - one for the scheduler clock and one for the +event tick/NOHZ. + +VIC required properties: + - compatible = "arm,pl192-vic". + - interrupt-controller. + - reg : The register bank for the device. + - #interrupt-cells : Must be 1. diff --git a/Documentation/devicetree/bindings/arm/pmu.txt b/Documentation/devicetree/bindings/arm/pmu.txt new file mode 100644 index 00000000..1c044eb3 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/pmu.txt @@ -0,0 +1,21 @@ +* ARM Performance Monitor Units + +ARM cores often have a PMU for counting cpu and cache events like cache misses +and hits. The interface to the PMU is part of the ARM ARM. The ARM PMU +representation in the device tree should be done as under:- + +Required properties: + +- compatible : should be one of + "arm,cortex-a9-pmu" + "arm,cortex-a8-pmu" + "arm,arm1176-pmu" + "arm,arm1136-pmu" +- interrupts : 1 combined interrupt or 1 per core. + +Example: + +pmu { + compatible = "arm,cortex-a9-pmu"; + interrupts = <100 101>; +}; diff --git a/Documentation/devicetree/bindings/arm/primecell.txt b/Documentation/devicetree/bindings/arm/primecell.txt new file mode 100644 index 00000000..951ca467 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/primecell.txt @@ -0,0 +1,23 @@ +* ARM Primecell Peripherals + +ARM, Ltd. Primecell peripherals have a standard id register that can be used to +identify the peripheral type, vendor, and revision. This value can be used for +driver matching. + +Required properties: + +- compatible : should be a specific name for the peripheral and + "arm,primecell". The specific name will match the ARM + engineering name for the logic block in the form: "arm,pl???" + +Optional properties: + +- arm,primecell-periphid : Value to override the h/w value with + +Example: + +serial@fff36000 { + compatible = "arm,pl011", "arm,primecell"; + arm,primecell-periphid = <0x00341011>; +}; + diff --git a/Documentation/devicetree/bindings/arm/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung-boards.txt new file mode 100644 index 00000000..0bf68be5 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/samsung-boards.txt @@ -0,0 +1,8 @@ +* Samsung's Exynos4210 based SMDKV310 evaluation board + +SMDKV310 evaluation board is based on Samsung's Exynos4210 SoC. + +Required root node properties: + - compatible = should be one or more of the following. + (a) "samsung,smdkv310" - for Samsung's SMDKV310 eval board. + (b) "samsung,exynos4210" - for boards based on Exynos4210 SoC. diff --git a/Documentation/devicetree/bindings/arm/sirf.txt b/Documentation/devicetree/bindings/arm/sirf.txt new file mode 100644 index 00000000..1881e1c6 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/sirf.txt @@ -0,0 +1,3 @@ +prima2 "cb" evaluation board +Required root node properties: + - compatible = "sirf,prima2-cb", "sirf,prima2"; diff --git a/Documentation/devicetree/bindings/arm/spear.txt b/Documentation/devicetree/bindings/arm/spear.txt new file mode 100644 index 00000000..f8e54f09 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/spear.txt @@ -0,0 +1,8 @@ +ST SPEAr Platforms Device Tree Bindings +--------------------------------------- + +Boards with the ST SPEAr600 SoC shall have the following properties: + +Required root node property: + +compatible = "st,spear600"; diff --git a/Documentation/devicetree/bindings/arm/tegra.txt b/Documentation/devicetree/bindings/arm/tegra.txt new file mode 100644 index 00000000..6e69d2e5 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/tegra.txt @@ -0,0 +1,14 @@ +NVIDIA Tegra device tree bindings +------------------------------------------- + +Boards with the tegra20 SoC shall have the following properties: + +Required root node property: + +compatible = "nvidia,tegra20"; + +Boards with the tegra30 SoC shall have the following properties: + +Required root node property: + +compatible = "nvidia,tegra30"; diff --git a/Documentation/devicetree/bindings/arm/tegra/emc.txt b/Documentation/devicetree/bindings/arm/tegra/emc.txt new file mode 100644 index 00000000..09335f8e --- /dev/null +++ b/Documentation/devicetree/bindings/arm/tegra/emc.txt @@ -0,0 +1,100 @@ +Embedded Memory Controller + +Properties: +- name : Should be emc +- #address-cells : Should be 1 +- #size-cells : Should be 0 +- compatible : Should contain "nvidia,tegra20-emc". +- reg : Offset and length of the register set for the device +- nvidia,use-ram-code : If present, the sub-nodes will be addressed + and chosen using the ramcode board selector. If omitted, only one + set of tables can be present and said tables will be used + irrespective of ram-code configuration. + +Child device nodes describe the memory settings for different configurations and clock rates. + +Example: + + emc@7000f400 { + #address-cells = < 1 >; + #size-cells = < 0 >; + compatible = "nvidia,tegra20-emc"; + reg = <0x7000f4000 0x200>; + } + + +Embedded Memory Controller ram-code table + +If the emc node has the nvidia,use-ram-code property present, then the +next level of nodes below the emc table are used to specify which settings +apply for which ram-code settings. + +If the emc node lacks the nvidia,use-ram-code property, this level is omitted +and the tables are stored directly under the emc node (see below). + +Properties: + +- name : Should be emc-tables +- nvidia,ram-code : the binary representation of the ram-code board strappings + for which this node (and children) are valid. + + + +Embedded Memory Controller configuration table + +This is a table containing the EMC register settings for the various +operating speeds of the memory controller. They are always located as +subnodes of the emc controller node. + +There are two ways of specifying which tables to use: + +* The simplest is if there is just one set of tables in the device tree, + and they will always be used (based on which frequency is used). + This is the preferred method, especially when firmware can fill in + this information based on the specific system information and just + pass it on to the kernel. + +* The slightly more complex one is when more than one memory configuration + might exist on the system. The Tegra20 platform handles this during + early boot by selecting one out of possible 4 memory settings based + on a 2-pin "ram code" bootstrap setting on the board. The values of + these strappings can be read through a register in the SoC, and thus + used to select which tables to use. + +Properties: +- name : Should be emc-table +- compatible : Should contain "nvidia,tegra20-emc-table". +- reg : either an opaque enumerator to tell different tables apart, or + the valid frequency for which the table should be used (in kHz). +- clock-frequency : the clock frequency for the EMC at which this + table should be used (in kHz). +- nvidia,emc-registers : a 46 word array of EMC registers to be programmed + for operation at the 'clock-frequency' setting. + The order and contents of the registers are: + RC, RFC, RAS, RP, R2W, W2R, R2P, W2P, RD_RCD, WR_RCD, RRD, REXT, + WDV, QUSE, QRST, QSAFE, RDV, REFRESH, BURST_REFRESH_NUM, PDEX2WR, + PDEX2RD, PCHG2PDEN, ACT2PDEN, AR2PDEN, RW2PDEN, TXSR, TCKE, TFAW, + TRPAB, TCLKSTABLE, TCLKSTOP, TREFBW, QUSE_EXTRA, FBIO_CFG6, ODT_WRITE, + ODT_READ, FBIO_CFG5, CFG_DIG_DLL, DLL_XFORM_DQS, DLL_XFORM_QUSE, + ZCAL_REF_CNT, ZCAL_WAIT_CNT, AUTO_CAL_INTERVAL, CFG_CLKTRIM_0, + CFG_CLKTRIM_1, CFG_CLKTRIM_2 + + emc-table@166000 { + reg = <166000>; + compatible = "nvidia,tegra20-emc-table"; + clock-frequency = < 166000 >; + nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0 + 0 0 0 0 0 0 0 0 0 0 0 0 0 0 + 0 0 0 0 0 0 0 0 0 0 0 0 0 0 + 0 0 0 0 >; + }; + + emc-table@333000 { + reg = <333000>; + compatible = "nvidia,tegra20-emc-table"; + clock-frequency = < 333000 >; + nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0 + 0 0 0 0 0 0 0 0 0 0 0 0 0 0 + 0 0 0 0 0 0 0 0 0 0 0 0 0 0 + 0 0 0 0 >; + }; diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt new file mode 100644 index 00000000..b5846e21 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt @@ -0,0 +1,19 @@ +NVIDIA Tegra Power Management Controller (PMC) + +Properties: +- name : Should be pmc +- compatible : Should contain "nvidia,tegra<chip>-pmc". +- reg : Offset and length of the register set for the device +- nvidia,invert-interrupt : If present, inverts the PMU interrupt signal. + The PMU is an external Power Management Unit, whose interrupt output + signal is fed into the PMC. This signal is optionally inverted, and then + fed into the ARM GIC. The PMC is not involved in the detection or + handling of this interrupt signal, merely its inversion. + +Example: + +pmc@7000f400 { + compatible = "nvidia,tegra20-pmc"; + reg = <0x7000e400 0x400>; + nvidia,invert-interrupt; +}; diff --git a/Documentation/devicetree/bindings/arm/twd.txt b/Documentation/devicetree/bindings/arm/twd.txt new file mode 100644 index 00000000..75b86109 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/twd.txt @@ -0,0 +1,48 @@ +* ARM Timer Watchdog + +ARM 11MP, Cortex-A5 and Cortex-A9 are often associated with a per-core +Timer-Watchdog (aka TWD), which provides both a per-cpu local timer +and watchdog. + +The TWD is usually attached to a GIC to deliver its two per-processor +interrupts. + +** Timer node required properties: + +- compatible : Should be one of: + "arm,cortex-a9-twd-timer" + "arm,cortex-a5-twd-timer" + "arm,arm11mp-twd-timer" + +- interrupts : One interrupt to each core + +- reg : Specify the base address and the size of the TWD timer + register window. + +Example: + + twd-timer@2c000600 { + compatible = "arm,arm11mp-twd-timer""; + reg = <0x2c000600 0x20>; + interrupts = <1 13 0xf01>; + }; + +** Watchdog node properties: + +- compatible : Should be one of: + "arm,cortex-a9-twd-wdt" + "arm,cortex-a5-twd-wdt" + "arm,arm11mp-twd-wdt" + +- interrupts : One interrupt to each core + +- reg : Specify the base address and the size of the TWD watchdog + register window. + +Example: + + twd-watchdog@2c000620 { + compatible = "arm,arm11mp-twd-wdt"; + reg = <0x2c000620 0x20>; + interrupts = <1 14 0xf01>; + }; diff --git a/Documentation/devicetree/bindings/arm/vexpress.txt b/Documentation/devicetree/bindings/arm/vexpress.txt new file mode 100644 index 00000000..ec8b50cb --- /dev/null +++ b/Documentation/devicetree/bindings/arm/vexpress.txt @@ -0,0 +1,146 @@ +ARM Versatile Express boards family +----------------------------------- + +ARM's Versatile Express platform consists of a motherboard and one +or more daughterboards (tiles). The motherboard provides a set of +peripherals. Processor and RAM "live" on the tiles. + +The motherboard and each core tile should be described by a separate +Device Tree source file, with the tile's description including +the motherboard file using a /include/ directive. As the motherboard +can be initialized in one of two different configurations ("memory +maps"), care must be taken to include the correct one. + +Required properties in the root node: +- compatible value: + compatible = "arm,vexpress,<model>", "arm,vexpress"; + where <model> is the full tile model name (as used in the tile's + Technical Reference Manual), eg.: + - for Coretile Express A5x2 (V2P-CA5s): + compatible = "arm,vexpress,v2p-ca5s", "arm,vexpress"; + - for Coretile Express A9x4 (V2P-CA9): + compatible = "arm,vexpress,v2p-ca9", "arm,vexpress"; + If a tile comes in several variants or can be used in more then one + configuration, the compatible value should be: + compatible = "arm,vexpress,<model>,<variant>", \ + "arm,vexpress,<model>", "arm,vexpress"; + eg: + - Coretile Express A15x2 (V2P-CA15) with Tech Chip 1: + compatible = "arm,vexpress,v2p-ca15,tc1", \ + "arm,vexpress,v2p-ca15", "arm,vexpress"; + - LogicTile Express 13MG (V2F-2XV6) running Cortex-A7 (3 cores) SMM: + compatible = "arm,vexpress,v2f-2xv6,ca7x3", \ + "arm,vexpress,v2f-2xv6", "arm,vexpress"; + +Optional properties in the root node: +- tile model name (use name from the tile's Technical Reference + Manual, eg. "V2P-CA5s") + model = "<model>"; +- tile's HBI number (unique ARM's board model ID, visible on the + PCB's silkscreen) in hexadecimal transcription: + arm,hbi = <0xhbi> + eg: + - for Coretile Express A5x2 (V2P-CA5s) HBI-0191: + arm,hbi = <0x191>; + - Coretile Express A9x4 (V2P-CA9) HBI-0225: + arm,hbi = <0x225>; + +Top-level standard "cpus" node is required. It must contain a node +with device_type = "cpu" property for every available core, eg.: + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a5"; + reg = <0>; + }; + }; + +The motherboard description file provides a single "motherboard" node +using 2 address cells corresponding to the Static Memory Bus used +between the motherboard and the tile. The first cell defines the Chip +Select (CS) line number, the second cell address offset within the CS. +All interrupt lines between the motherboard and the tile are active +high and are described using single cell. + +Optional properties of the "motherboard" node: +- motherboard's memory map variant: + arm,v2m-memory-map = "<name>"; + where name is one of: + - "rs1" - for RS1 map (i.a. peripherals on CS3); this map is also + referred to as "ARM Cortex-A Series memory map": + arm,v2m-memory-map = "rs1"; + When this property is missing, the motherboard is using the original + memory map (also known as the "Legacy memory map", primarily used + with the original CoreTile Express A9x4) with peripherals on CS7. + +Motherboard .dtsi files provide a set of labelled peripherals that +can be used to obtain required phandle in the tile's "aliases" node: +- UARTs, note that the numbers correspond to the physical connectors + on the motherboard's back panel: + v2m_serial0, v2m_serial1, v2m_serial2 and v2m_serial3 +- I2C controllers: + v2m_i2c_dvi and v2m_i2c_pcie +- SP804 timers: + v2m_timer01 and v2m_timer23 + +Current Linux implementation requires a "arm,v2m_timer" alias +pointing at one of the motherboard's SP804 timers, if it is to be +used as the system timer. This alias should be defined in the +motherboard files. + +The tile description must define "ranges", "interrupt-map-mask" and +"interrupt-map" properties to translate the motherboard's address +and interrupt space into one used by the tile's processor. + +Abbreviated example: + +/dts-v1/; + +/ { + model = "V2P-CA5s"; + arm,hbi = <0x225>; + compatible = "arm,vexpress-v2p-ca5s", "arm,vexpress"; + interrupt-parent = <&gic>; + #address-cells = <1>; + #size-cells = <1>; + + chosen { }; + + aliases { + serial0 = &v2m_serial0; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a5"; + reg = <0>; + }; + }; + + gic: interrupt-controller@2c001000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + #address-cells = <0>; + interrupt-controller; + reg = <0x2c001000 0x1000>, + <0x2c000100 0x100>; + }; + + motherboard { + /* CS0 is visible at 0x08000000 */ + ranges = <0 0 0x08000000 0x04000000>; + interrupt-map-mask = <0 0 63>; + /* Active high IRQ 0 is connected to GIC's SPI0 */ + interrupt-map = <0 0 0 &gic 0 0 4>; + }; +}; + +/include/ "vexpress-v2m-rs1.dtsi" diff --git a/Documentation/devicetree/bindings/arm/vic.txt b/Documentation/devicetree/bindings/arm/vic.txt new file mode 100644 index 00000000..266716b2 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/vic.txt @@ -0,0 +1,29 @@ +* ARM Vectored Interrupt Controller + +One or more Vectored Interrupt Controllers (VIC's) can be connected in an ARM +system for interrupt routing. For multiple controllers they can either be +nested or have the outputs wire-OR'd together. + +Required properties: + +- compatible : should be one of + "arm,pl190-vic" + "arm,pl192-vic" +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : The number of cells to define the interrupts. Must be 1 as + the VIC has no configuration options for interrupt sources. The cell is a u32 + and defines the interrupt number. +- reg : The register bank for the VIC. + +Optional properties: + +- interrupts : Interrupt source for parent controllers if the VIC is nested. + +Example: + + vic0: interrupt-controller@60000 { + compatible = "arm,pl192-vic"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x60000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/arm/xilinx.txt b/Documentation/devicetree/bindings/arm/xilinx.txt new file mode 100644 index 00000000..6f1ed830 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/xilinx.txt @@ -0,0 +1,7 @@ +Xilinx Zynq EP107 Emulation Platform board + +This board is an emulation platform for the Zynq product which is +based on an ARM Cortex A9 processor. + +Required root node properties: + - compatible = "xlnx,zynq-ep107"; diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt new file mode 100644 index 00000000..8bb8a76d --- /dev/null +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt @@ -0,0 +1,16 @@ +* AHCI SATA Controller + +SATA nodes are defined to describe on-chip Serial ATA controllers. +Each SATA controller should have its own node. + +Required properties: +- compatible : compatible list, contains "calxeda,hb-ahci" or "snps,spear-ahci" +- interrupts : <interrupt mapping for SATA IRQ> +- reg : <registers mapping> + +Example: + sata@ffe08000 { + compatible = "calxeda,hb-ahci"; + reg = <0xffe08000 0x1000>; + interrupts = <115>; + }; diff --git a/Documentation/devicetree/bindings/ata/fsl-sata.txt b/Documentation/devicetree/bindings/ata/fsl-sata.txt new file mode 100644 index 00000000..b46bcf46 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/fsl-sata.txt @@ -0,0 +1,29 @@ +* Freescale 8xxx/3.0 Gb/s SATA nodes + +SATA nodes are defined to describe on-chip Serial ATA controllers. +Each SATA port should have its own node. + +Required properties: +- compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-sata", where CHIP is the processor + (mpc8315, mpc8379, etc.) and the second is + "fsl,pq-sata" +- interrupts : <interrupt mapping for SATA IRQ> +- cell-index : controller index. + 1 for controller @ 0x18000 + 2 for controller @ 0x19000 + 3 for controller @ 0x1a000 + 4 for controller @ 0x1b000 + +Optional properties: +- interrupt-parent : optional, if needed for interrupt mapping +- reg : <registers mapping> + +Example: + sata@18000 { + compatible = "fsl,mpc8379-sata", "fsl,pq-sata"; + reg = <0x18000 0x1000>; + cell-index = <1>; + interrupts = <2c 8>; + interrupt-parent = < &ipic >; + }; diff --git a/Documentation/devicetree/bindings/c6x/clocks.txt b/Documentation/devicetree/bindings/c6x/clocks.txt new file mode 100644 index 00000000..a04f5fd3 --- /dev/null +++ b/Documentation/devicetree/bindings/c6x/clocks.txt @@ -0,0 +1,40 @@ +C6X PLL Clock Controllers +------------------------- + +This is a first-cut support for the SoC clock controllers. This is still +under development and will probably change as the common device tree +clock support is added to the kernel. + +Required properties: + +- compatible: "ti,c64x+pll" + May also have SoC-specific value to support SoC-specific initialization + in the driver. One of: + "ti,c6455-pll" + "ti,c6457-pll" + "ti,c6472-pll" + "ti,c6474-pll" + +- reg: base address and size of register area +- clock-frequency: input clock frequency in hz + + +Optional properties: + +- ti,c64x+pll-bypass-delay: CPU cycles to delay when entering bypass mode + +- ti,c64x+pll-reset-delay: CPU cycles to delay after PLL reset + +- ti,c64x+pll-lock-delay: CPU cycles to delay after PLL frequency change + +Example: + + clock-controller@29a0000 { + compatible = "ti,c6472-pll", "ti,c64x+pll"; + reg = <0x029a0000 0x200>; + clock-frequency = <25000000>; + + ti,c64x+pll-bypass-delay = <200>; + ti,c64x+pll-reset-delay = <12000>; + ti,c64x+pll-lock-delay = <80000>; + }; diff --git a/Documentation/devicetree/bindings/c6x/dscr.txt b/Documentation/devicetree/bindings/c6x/dscr.txt new file mode 100644 index 00000000..d847758f --- /dev/null +++ b/Documentation/devicetree/bindings/c6x/dscr.txt @@ -0,0 +1,127 @@ +Device State Configuration Registers +------------------------------------ + +TI C6X SoCs contain a region of miscellaneous registers which provide various +function for SoC control or status. Details vary considerably among from SoC +to SoC with no two being alike. + +In general, the Device State Configuraion Registers (DSCR) will provide one or +more configuration registers often protected by a lock register where one or +more key values must be written to a lock register in order to unlock the +configuration register for writes. These configuration register may be used to +enable (and disable in some cases) SoC pin drivers, select peripheral clock +sources (internal or pin), etc. In some cases, a configuration register is +write once or the individual bits are write once. In addition to device config, +the DSCR block may provide registers which which are used to reset peripherals, +provide device ID information, provide ethernet MAC addresses, as well as other +miscellaneous functions. + +For device state control (enable/disable), each device control is assigned an +id which is used by individual device drivers to control the state as needed. + +Required properties: + +- compatible: must be "ti,c64x+dscr" +- reg: register area base and size + +Optional properties: + + NOTE: These are optional in that not all SoCs will have all properties. For + SoCs which do support a given property, leaving the property out of the + device tree will result in reduced functionality or possibly driver + failure. + +- ti,dscr-devstat + offset of the devstat register + +- ti,dscr-silicon-rev + offset, start bit, and bitsize of silicon revision field + +- ti,dscr-rmii-resets + offset and bitmask of RMII reset field. May have multiple tuples if more + than one ethernet port is available. + +- ti,dscr-locked-regs + possibly multiple tuples describing registers which are write protected by + a lock register. Each tuple consists of the register offset, lock register + offsset, and the key value used to unlock the register. + +- ti,dscr-kick-regs + offset and key values of two "kick" registers used to write protect other + registers in DSCR. On SoCs using kick registers, the first key must be + written to the first kick register and the second key must be written to + the second register before other registers in the area are write-enabled. + +- ti,dscr-mac-fuse-regs + MAC addresses are contained in two registers. Each element of a MAC address + is contained in a single byte. This property has two tuples. Each tuple has + a register offset and four cells representing bytes in the register from + most significant to least. The value of these four cells is the MAC byte + index (1-6) of the byte within the register. A value of 0 means the byte + is unused in the MAC address. + +- ti,dscr-devstate-ctl-regs + This property describes the bitfields used to control the state of devices. + Each tuple describes a range of identical bitfields used to control one or + more devices (one bitfield per device). The layout of each tuple is: + + start_id num_ids reg enable disable start_bit nbits + + Where: + start_id is device id for the first device control in the range + num_ids is the number of device controls in the range + reg is the offset of the register holding the control bits + enable is the value to enable a device + disable is the value to disable a device (0xffffffff if cannot disable) + start_bit is the bit number of the first bit in the range + nbits is the number of bits per device control + +- ti,dscr-devstate-stat-regs + This property describes the bitfields used to provide device state status + for device states controlled by the DSCR. Each tuple describes a range of + identical bitfields used to provide status for one or more devices (one + bitfield per device). The layout of each tuple is: + + start_id num_ids reg enable disable start_bit nbits + + Where: + start_id is device id for the first device status in the range + num_ids is the number of devices covered by the range + reg is the offset of the register holding the status bits + enable is the value indicating device is enabled + disable is the value indicating device is disabled + start_bit is the bit number of the first bit in the range + nbits is the number of bits per device status + +- ti,dscr-privperm + Offset and default value for register used to set access privilege for + some SoC devices. + + +Example: + + device-state-config-regs@2a80000 { + compatible = "ti,c64x+dscr"; + reg = <0x02a80000 0x41000>; + + ti,dscr-devstat = <0>; + ti,dscr-silicon-rev = <8 28 0xf>; + ti,dscr-rmii-resets = <0x40020 0x00040000>; + + ti,dscr-locked-regs = <0x40008 0x40004 0x0f0a0b00>; + ti,dscr-devstate-ctl-regs = + <0 12 0x40008 1 0 0 2 + 12 1 0x40008 3 0 30 2 + 13 2 0x4002c 1 0xffffffff 0 1>; + ti,dscr-devstate-stat-regs = + <0 10 0x40014 1 0 0 3 + 10 2 0x40018 1 0 0 3>; + + ti,dscr-mac-fuse-regs = <0x700 1 2 3 4 + 0x704 5 6 0 0>; + + ti,dscr-privperm = <0x41c 0xaaaaaaaa>; + + ti,dscr-kick-regs = <0x38 0x83E70B13 + 0x3c 0x95A4F1E0>; + }; diff --git a/Documentation/devicetree/bindings/c6x/emifa.txt b/Documentation/devicetree/bindings/c6x/emifa.txt new file mode 100644 index 00000000..0ff6e9b9 --- /dev/null +++ b/Documentation/devicetree/bindings/c6x/emifa.txt @@ -0,0 +1,62 @@ +External Memory Interface +------------------------- + +The emifa node describes a simple external bus controller found on some C6X +SoCs. This interface provides external busses with a number of chip selects. + +Required properties: + +- compatible: must be "ti,c64x+emifa", "simple-bus" +- reg: register area base and size +- #address-cells: must be 2 (chip-select + offset) +- #size-cells: must be 1 +- ranges: mapping from EMIFA space to parent space + + +Optional properties: + +- ti,dscr-dev-enable: Device ID if EMIF is enabled/disabled from DSCR + +- ti,emifa-burst-priority: + Number of memory transfers after which the EMIF will elevate the priority + of the oldest command in the command FIFO. Setting this field to 255 + disables this feature, thereby allowing old commands to stay in the FIFO + indefinitely. + +- ti,emifa-ce-config: + Configuration values for each of the supported chip selects. + +Example: + + emifa@70000000 { + compatible = "ti,c64x+emifa", "simple-bus"; + #address-cells = <2>; + #size-cells = <1>; + reg = <0x70000000 0x100>; + ranges = <0x2 0x0 0xa0000000 0x00000008 + 0x3 0x0 0xb0000000 0x00400000 + 0x4 0x0 0xc0000000 0x10000000 + 0x5 0x0 0xD0000000 0x10000000>; + + ti,dscr-dev-enable = <13>; + ti,emifa-burst-priority = <255>; + ti,emifa-ce-config = <0x00240120 + 0x00240120 + 0x00240122 + 0x00240122>; + + flash@3,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "cfi-flash"; + reg = <0x3 0x0 0x400000>; + bank-width = <1>; + device-width = <1>; + partition@0 { + reg = <0x0 0x400000>; + label = "NOR"; + }; + }; + }; + +This shows a flash chip attached to chip select 3. diff --git a/Documentation/devicetree/bindings/c6x/interrupt.txt b/Documentation/devicetree/bindings/c6x/interrupt.txt new file mode 100644 index 00000000..42bb796c --- /dev/null +++ b/Documentation/devicetree/bindings/c6x/interrupt.txt @@ -0,0 +1,104 @@ +C6X Interrupt Chips +------------------- + +* C64X+ Core Interrupt Controller + + The core interrupt controller provides 16 prioritized interrupts to the + C64X+ core. Priority 0 and 1 are used for reset and NMI respectively. + Priority 2 and 3 are reserved. Priority 4-15 are used for interrupt + sources coming from outside the core. + + Required properties: + -------------------- + - compatible: Should be "ti,c64x+core-pic"; + - #interrupt-cells: <1> + + Interrupt Specifier Definition + ------------------------------ + Single cell specifying the core interrupt priority level (4-15) where + 4 is highest priority and 15 is lowest priority. + + Example + ------- + core_pic: interrupt-controller@0 { + interrupt-controller; + #interrupt-cells = <1>; + compatible = "ti,c64x+core-pic"; + }; + + + +* C64x+ Megamodule Interrupt Controller + + The megamodule PIC consists of four interrupt mupliplexers each of which + combine up to 32 interrupt inputs into a single interrupt output which + may be cascaded into the core interrupt controller. The megamodule PIC + has a total of 12 outputs cascading into the core interrupt controller. + One for each core interrupt priority level. In addition to the combined + interrupt sources, individual megamodule interrupts may be cascaded to + the core interrupt controller. When an individual interrupt is cascaded, + it is no longer handled through a megamodule interrupt combiner and is + considered to have the core interrupt controller as the parent. + + Required properties: + -------------------- + - compatible: "ti,c64x+megamod-pic" + - interrupt-controller + - #interrupt-cells: <1> + - reg: base address and size of register area + - interrupt-parent: must be core interrupt controller + - interrupts: This should have four cells; one for each interrupt combiner. + The cells contain the core priority interrupt to which the + corresponding combiner output is wired. + + Optional properties: + -------------------- + - ti,c64x+megamod-pic-mux: Array of 12 cells correspnding to the 12 core + priority interrupts. The first cell corresponds to + core priority 4 and the last cell corresponds to + core priority 15. The value of each cell is the + megamodule interrupt source which is MUXed to + the core interrupt corresponding to the cell + position. Allowed values are 4 - 127. Mapping for + interrupts 0 - 3 (combined interrupt sources) are + ignored. + + Interrupt Specifier Definition + ------------------------------ + Single cell specifying the megamodule interrupt source (4-127). Note that + interrupts mapped directly to the core with "ti,c64x+megamod-pic-mux" will + use the core interrupt controller as their parent and the specifier will + be the core priority level, not the megamodule interrupt number. + + Examples + -------- + megamod_pic: interrupt-controller@1800000 { + compatible = "ti,c64x+megamod-pic"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x1800000 0x1000>; + interrupt-parent = <&core_pic>; + interrupts = < 12 13 14 15 >; + }; + + This is a minimal example where all individual interrupts go through a + combiner. Combiner-0 is mapped to core interrupt 12, combiner-1 is mapped + to interrupt 13, etc. + + + megamod_pic: interrupt-controller@1800000 { + compatible = "ti,c64x+megamod-pic"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x1800000 0x1000>; + interrupt-parent = <&core_pic>; + interrupts = < 12 13 14 15 >; + ti,c64x+megamod-pic-mux = < 0 0 0 0 + 32 0 0 0 + 0 0 0 0 >; + }; + + This the same as the first example except that megamodule interrupt 32 is + mapped directly to core priority interrupt 8. The node using this interrupt + must set the core controller as its interrupt parent and use 8 in the + interrupt specifier value. diff --git a/Documentation/devicetree/bindings/c6x/soc.txt b/Documentation/devicetree/bindings/c6x/soc.txt new file mode 100644 index 00000000..b1e4973b --- /dev/null +++ b/Documentation/devicetree/bindings/c6x/soc.txt @@ -0,0 +1,28 @@ +C6X System-on-Chip +------------------ + +Required properties: + +- compatible: "simple-bus" +- #address-cells: must be 1 +- #size-cells: must be 1 +- ranges + +Optional properties: + +- model: specific SoC model + +- nodes for IP blocks within SoC + + +Example: + + soc { + compatible = "simple-bus"; + model = "tms320c6455"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + ... + }; diff --git a/Documentation/devicetree/bindings/c6x/timer64.txt b/Documentation/devicetree/bindings/c6x/timer64.txt new file mode 100644 index 00000000..95911fe7 --- /dev/null +++ b/Documentation/devicetree/bindings/c6x/timer64.txt @@ -0,0 +1,26 @@ +Timer64 +------- + +The timer64 node describes C6X event timers. + +Required properties: + +- compatible: must be "ti,c64x+timer64" +- reg: base address and size of register region +- interrupt-parent: interrupt controller +- interrupts: interrupt id + +Optional properties: + +- ti,dscr-dev-enable: Device ID used to enable timer IP through DSCR interface. + +- ti,core-mask: on multi-core SoCs, bitmask of cores allowed to use this timer. + +Example: + timer0: timer@25e0000 { + compatible = "ti,c64x+timer64"; + ti,core-mask = < 0x01 >; + reg = <0x25e0000 0x40>; + interrupt-parent = <&megamod_pic>; + interrupts = < 16 >; + }; diff --git a/Documentation/devicetree/bindings/crypto/fsl-sec2.txt b/Documentation/devicetree/bindings/crypto/fsl-sec2.txt new file mode 100644 index 00000000..38988ef1 --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/fsl-sec2.txt @@ -0,0 +1,68 @@ +Freescale SoC SEC Security Engines versions 2.x-3.x + +Required properties: + +- compatible : Should contain entries for this and backward compatible + SEC versions, high to low, e.g., "fsl,sec2.1", "fsl,sec2.0" +- reg : Offset and length of the register set for the device +- interrupts : the SEC's interrupt number +- fsl,num-channels : An integer representing the number of channels + available. +- fsl,channel-fifo-len : An integer representing the number of + descriptor pointers each channel fetch fifo can hold. +- fsl,exec-units-mask : The bitmask representing what execution units + (EUs) are available. It's a single 32-bit cell. EU information + should be encoded following the SEC's Descriptor Header Dword + EU_SEL0 field documentation, i.e. as follows: + + bit 0 = reserved - should be 0 + bit 1 = set if SEC has the ARC4 EU (AFEU) + bit 2 = set if SEC has the DES/3DES EU (DEU) + bit 3 = set if SEC has the message digest EU (MDEU/MDEU-A) + bit 4 = set if SEC has the random number generator EU (RNG) + bit 5 = set if SEC has the public key EU (PKEU) + bit 6 = set if SEC has the AES EU (AESU) + bit 7 = set if SEC has the Kasumi EU (KEU) + bit 8 = set if SEC has the CRC EU (CRCU) + bit 11 = set if SEC has the message digest EU extended alg set (MDEU-B) + +remaining bits are reserved for future SEC EUs. + +- fsl,descriptor-types-mask : The bitmask representing what descriptors + are available. It's a single 32-bit cell. Descriptor type information + should be encoded following the SEC's Descriptor Header Dword DESC_TYPE + field documentation, i.e. as follows: + + bit 0 = set if SEC supports the aesu_ctr_nonsnoop desc. type + bit 1 = set if SEC supports the ipsec_esp descriptor type + bit 2 = set if SEC supports the common_nonsnoop desc. type + bit 3 = set if SEC supports the 802.11i AES ccmp desc. type + bit 4 = set if SEC supports the hmac_snoop_no_afeu desc. type + bit 5 = set if SEC supports the srtp descriptor type + bit 6 = set if SEC supports the non_hmac_snoop_no_afeu desc.type + bit 7 = set if SEC supports the pkeu_assemble descriptor type + bit 8 = set if SEC supports the aesu_key_expand_output desc.type + bit 9 = set if SEC supports the pkeu_ptmul descriptor type + bit 10 = set if SEC supports the common_nonsnoop_afeu desc. type + bit 11 = set if SEC supports the pkeu_ptadd_dbl descriptor type + + ..and so on and so forth. + +Optional properties: + +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Example: + + /* MPC8548E */ + crypto@30000 { + compatible = "fsl,sec2.1", "fsl,sec2.0"; + reg = <0x30000 0x10000>; + interrupts = <29 2>; + interrupt-parent = <&mpic>; + fsl,num-channels = <4>; + fsl,channel-fifo-len = <24>; + fsl,exec-units-mask = <0xfe>; + fsl,descriptor-types-mask = <0x12b0ebf>; + }; diff --git a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt new file mode 100644 index 00000000..bf57ecd5 --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt @@ -0,0 +1,397 @@ +===================================================================== +SEC 4 Device Tree Binding +Copyright (C) 2008-2011 Freescale Semiconductor Inc. + + CONTENTS + -Overview + -SEC 4 Node + -Job Ring Node + -Run Time Integrity Check (RTIC) Node + -Run Time Integrity Check (RTIC) Memory Node + -Secure Non-Volatile Storage (SNVS) Node + -Full Example + +NOTE: the SEC 4 is also known as Freescale's Cryptographic Accelerator +Accelerator and Assurance Module (CAAM). + +===================================================================== +Overview + +DESCRIPTION + +SEC 4 h/w can process requests from 2 types of sources. +1. DPAA Queue Interface (HW interface between Queue Manager & SEC 4). +2. Job Rings (HW interface between cores & SEC 4 registers). + +High Speed Data Path Configuration: + +HW interface between QM & SEC 4 and also BM & SEC 4, on DPAA-enabled parts +such as the P4080. The number of simultaneous dequeues the QI can make is +equal to the number of Descriptor Controller (DECO) engines in a particular +SEC version. E.g., the SEC 4.0 in the P4080 has 5 DECOs and can thus +dequeue from 5 subportals simultaneously. + +Job Ring Data Path Configuration: + +Each JR is located on a separate 4k page, they may (or may not) be made visible +in the memory partition devoted to a particular core. The P4080 has 4 JRs, so +up to 4 JRs can be configured; and all 4 JRs process requests in parallel. + +===================================================================== +SEC 4 Node + +Description + + Node defines the base address of the SEC 4 block. + This block specifies the address range of all global + configuration registers for the SEC 4 block. It + also receives interrupts from the Run Time Integrity Check + (RTIC) function within the SEC 4 block. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,sec-v4.0" + + - #address-cells + Usage: required + Value type: <u32> + Definition: A standard property. Defines the number of cells + for representing physical addresses in child nodes. + + - #size-cells + Usage: required + Value type: <u32> + Definition: A standard property. Defines the number of cells + for representing the size of physical addresses in + child nodes. + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical + address and length of the SEC4 configuration registers. + registers + + - ranges + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + range of the SEC 4.0 register space (-SNVS not included). A + triplet that includes the child address, parent address, & + length. + + - interrupts + Usage: required + Value type: <prop_encoded-array> + Definition: Specifies the interrupts generated by this + device. The value of the interrupts property + consists of one interrupt specifier. The format + of the specifier is defined by the binding document + describing the node's interrupt parent. + + - interrupt-parent + Usage: (required if interrupt property is defined) + Value type: <phandle> + Definition: A single <phandle> value that points + to the interrupt parent to which the child domain + is being mapped. + + Note: All other standard properties (see the ePAPR) are allowed + but are optional. + + +EXAMPLE + crypto@300000 { + compatible = "fsl,sec-v4.0"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x300000 0x10000>; + ranges = <0 0x300000 0x10000>; + interrupt-parent = <&mpic>; + interrupts = <92 2>; + }; + +===================================================================== +Job Ring (JR) Node + + Child of the crypto node defines data processing interface to SEC 4 + across the peripheral bus for purposes of processing + cryptographic descriptors. The specified address + range can be made visible to one (or more) cores. + The interrupt defined for this node is controlled within + the address range of this node. + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,sec-v4.0-job-ring" + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: Specifies a two JR parameters: an offset from + the parent physical address and the length the JR registers. + + - fsl,liodn + Usage: optional-but-recommended + Value type: <prop-encoded-array> + Definition: + Specifies the LIODN to be used in conjunction with + the ppid-to-liodn table that specifies the PPID to LIODN mapping. + Needed if the PAMU is used. Value is a 12 bit value + where value is a LIODN ID for this JR. This property is + normally set by boot firmware. + + - interrupts + Usage: required + Value type: <prop_encoded-array> + Definition: Specifies the interrupts generated by this + device. The value of the interrupts property + consists of one interrupt specifier. The format + of the specifier is defined by the binding document + describing the node's interrupt parent. + + - interrupt-parent + Usage: (required if interrupt property is defined) + Value type: <phandle> + Definition: A single <phandle> value that points + to the interrupt parent to which the child domain + is being mapped. + +EXAMPLE + jr@1000 { + compatible = "fsl,sec-v4.0-job-ring"; + reg = <0x1000 0x1000>; + fsl,liodn = <0x081>; + interrupt-parent = <&mpic>; + interrupts = <88 2>; + }; + + +===================================================================== +Run Time Integrity Check (RTIC) Node + + Child node of the crypto node. Defines a register space that + contains up to 5 sets of addresses and their lengths (sizes) that + will be checked at run time. After an initial hash result is + calculated, these addresses are checked by HW to monitor any + change. If any memory is modified, a Security Violation is + triggered (see SNVS definition). + + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,sec-v4.0-rtic". + + - #address-cells + Usage: required + Value type: <u32> + Definition: A standard property. Defines the number of cells + for representing physical addresses in child nodes. Must + have a value of 1. + + - #size-cells + Usage: required + Value type: <u32> + Definition: A standard property. Defines the number of cells + for representing the size of physical addresses in + child nodes. Must have a value of 1. + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies a two parameters: + an offset from the parent physical address and the length + the SEC4 registers. + + - ranges + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + range of the SEC 4 register space (-SNVS not included). A + triplet that includes the child address, parent address, & + length. + +EXAMPLE + rtic@6000 { + compatible = "fsl,sec-v4.0-rtic"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x6000 0x100>; + ranges = <0x0 0x6100 0xe00>; + }; + +===================================================================== +Run Time Integrity Check (RTIC) Memory Node + A child node that defines individual RTIC memory regions that are used to + perform run-time integrity check of memory areas that should not modified. + The node defines a register that contains the memory address & + length (combined) and a second register that contains the hash result + in big endian format. + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,sec-v4.0-rtic-memory". + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies two parameters: + an offset from the parent physical address and the length: + + 1. The location of the RTIC memory address & length registers. + 2. The location RTIC hash result. + + - fsl,rtic-region + Usage: optional-but-recommended + Value type: <prop-encoded-array> + Definition: + Specifies the HW address (36 bit address) for this region + followed by the length of the HW partition to be checked; + the address is represented as a 64 bit quantity followed + by a 32 bit length. + + - fsl,liodn + Usage: optional-but-recommended + Value type: <prop-encoded-array> + Definition: + Specifies the LIODN to be used in conjunction with + the ppid-to-liodn table that specifies the PPID to LIODN + mapping. Needed if the PAMU is used. Value is a 12 bit value + where value is a LIODN ID for this RTIC memory region. This + property is normally set by boot firmware. + +EXAMPLE + rtic-a@0 { + compatible = "fsl,sec-v4.0-rtic-memory"; + reg = <0x00 0x20 0x100 0x80>; + fsl,liodn = <0x03c>; + fsl,rtic-region = <0x12345678 0x12345678 0x12345678>; + }; + +===================================================================== +Secure Non-Volatile Storage (SNVS) Node + + Node defines address range and the associated + interrupt for the SNVS function. This function + monitors security state information & reports + security violations. + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,sec-v4.0-mon". + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical + address and length of the SEC4 configuration + registers. + + - interrupts + Usage: required + Value type: <prop_encoded-array> + Definition: Specifies the interrupts generated by this + device. The value of the interrupts property + consists of one interrupt specifier. The format + of the specifier is defined by the binding document + describing the node's interrupt parent. + + - interrupt-parent + Usage: (required if interrupt property is defined) + Value type: <phandle> + Definition: A single <phandle> value that points + to the interrupt parent to which the child domain + is being mapped. + +EXAMPLE + sec_mon@314000 { + compatible = "fsl,sec-v4.0-mon"; + reg = <0x314000 0x1000>; + interrupt-parent = <&mpic>; + interrupts = <93 2>; + }; + +===================================================================== +FULL EXAMPLE + + crypto: crypto@300000 { + compatible = "fsl,sec-v4.0"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x300000 0x10000>; + ranges = <0 0x300000 0x10000>; + interrupt-parent = <&mpic>; + interrupts = <92 2>; + + sec_jr0: jr@1000 { + compatible = "fsl,sec-v4.0-job-ring"; + reg = <0x1000 0x1000>; + interrupt-parent = <&mpic>; + interrupts = <88 2>; + }; + + sec_jr1: jr@2000 { + compatible = "fsl,sec-v4.0-job-ring"; + reg = <0x2000 0x1000>; + interrupt-parent = <&mpic>; + interrupts = <89 2>; + }; + + sec_jr2: jr@3000 { + compatible = "fsl,sec-v4.0-job-ring"; + reg = <0x3000 0x1000>; + interrupt-parent = <&mpic>; + interrupts = <90 2>; + }; + + sec_jr3: jr@4000 { + compatible = "fsl,sec-v4.0-job-ring"; + reg = <0x4000 0x1000>; + interrupt-parent = <&mpic>; + interrupts = <91 2>; + }; + + rtic@6000 { + compatible = "fsl,sec-v4.0-rtic"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x6000 0x100>; + ranges = <0x0 0x6100 0xe00>; + + rtic_a: rtic-a@0 { + compatible = "fsl,sec-v4.0-rtic-memory"; + reg = <0x00 0x20 0x100 0x80>; + }; + + rtic_b: rtic-b@20 { + compatible = "fsl,sec-v4.0-rtic-memory"; + reg = <0x20 0x20 0x200 0x80>; + }; + + rtic_c: rtic-c@40 { + compatible = "fsl,sec-v4.0-rtic-memory"; + reg = <0x40 0x20 0x300 0x80>; + }; + + rtic_d: rtic-d@60 { + compatible = "fsl,sec-v4.0-rtic-memory"; + reg = <0x60 0x20 0x500 0x80>; + }; + }; + }; + + sec_mon: sec_mon@314000 { + compatible = "fsl,sec-v4.0-mon"; + reg = <0x314000 0x1000>; + interrupt-parent = <&mpic>; + interrupts = <93 2>; + }; + +===================================================================== diff --git a/Documentation/devicetree/bindings/crypto/picochip-spacc.txt b/Documentation/devicetree/bindings/crypto/picochip-spacc.txt new file mode 100644 index 00000000..d8609ece --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/picochip-spacc.txt @@ -0,0 +1,23 @@ +Picochip picoXcell SPAcc (Security Protocol Accelerator) bindings + +Picochip picoXcell devices contain crypto offload engines that may be used for +IPSEC and femtocell layer 2 ciphering. + +Required properties: + - compatible : "picochip,spacc-ipsec" for the IPSEC offload engine + "picochip,spacc-l2" for the femtocell layer 2 ciphering engine. + - reg : Offset and length of the register set for this device + - interrupt-parent : The interrupt controller that controls the SPAcc + interrupt. + - interrupts : The interrupt line from the SPAcc. + - ref-clock : The input clock that drives the SPAcc. + +Example SPAcc node: + +spacc@10000 { + compatible = "picochip,spacc-ipsec"; + reg = <0x100000 0x10000>; + interrupt-parent = <&vic0>; + interrupts = <24>; + ref-clock = <&ipsec_clk>, "ref"; +}; diff --git a/Documentation/devicetree/bindings/dma/arm-pl330.txt b/Documentation/devicetree/bindings/dma/arm-pl330.txt new file mode 100644 index 00000000..a4cd273b --- /dev/null +++ b/Documentation/devicetree/bindings/dma/arm-pl330.txt @@ -0,0 +1,30 @@ +* ARM PrimeCell PL330 DMA Controller + +The ARM PrimeCell PL330 DMA controller can move blocks of memory contents +between memory and peripherals or memory to memory. + +Required properties: + - compatible: should include both "arm,pl330" and "arm,primecell". + - reg: physical base address of the controller and length of memory mapped + region. + - interrupts: interrupt number to the cpu. + +Example: + + pdma0: pdma@12680000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x12680000 0x1000>; + interrupts = <99>; + }; + +Client drivers (device nodes requiring dma transfers from dev-to-mem or +mem-to-dev) should specify the DMA channel numbers using a two-value pair +as shown below. + + [property name] = <[phandle of the dma controller] [dma request id]>; + + where 'dma request id' is the dma request number which is connected + to the client controller. The 'property name' is recommended to be + of the form <name>-dma-channel. + + Example: tx-dma-channel = <&pdma0 12>; diff --git a/Documentation/devicetree/bindings/dma/atmel-dma.txt b/Documentation/devicetree/bindings/dma/atmel-dma.txt new file mode 100644 index 00000000..3c046ee6 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/atmel-dma.txt @@ -0,0 +1,14 @@ +* Atmel Direct Memory Access Controller (DMA) + +Required properties: +- compatible: Should be "atmel,<chip>-dma" +- reg: Should contain DMA registers location and length +- interrupts: Should contain DMA interrupt + +Examples: + +dma@ffffec00 { + compatible = "atmel,at91sam9g45-dma"; + reg = <0xffffec00 0x200>; + interrupts = <21>; +}; diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt new file mode 100644 index 00000000..d1e3f443 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt @@ -0,0 +1,17 @@ +* Freescale Smart Direct Memory Access (SDMA) Controller for i.MX + +Required properties: +- compatible : Should be "fsl,<chip>-sdma" +- reg : Should contain SDMA registers location and length +- interrupts : Should contain SDMA interrupt +- fsl,sdma-ram-script-name : Should contain the full path of SDMA RAM + scripts firmware + +Examples: + +sdma@83fb0000 { + compatible = "fsl,imx51-sdma", "fsl,imx35-sdma"; + reg = <0x83fb0000 0x4000>; + interrupts = <6>; + fsl,sdma-ram-script-name = "sdma-imx51.bin"; +}; diff --git a/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt b/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt new file mode 100644 index 00000000..90fa7da5 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt @@ -0,0 +1,30 @@ +* NVIDIA Tegra APB DMA controller + +Required properties: +- compatible: Should be "nvidia,<chip>-apbdma" +- reg: Should contain DMA registers location and length. This shuld include + all of the per-channel registers. +- interrupts: Should contain all of the per-channel DMA interrupts. + +Examples: + +apbdma: dma@6000a000 { + compatible = "nvidia,tegra20-apbdma"; + reg = <0x6000a000 0x1200>; + interrupts = < 0 136 0x04 + 0 137 0x04 + 0 138 0x04 + 0 139 0x04 + 0 140 0x04 + 0 141 0x04 + 0 142 0x04 + 0 143 0x04 + 0 144 0x04 + 0 145 0x04 + 0 146 0x04 + 0 147 0x04 + 0 148 0x04 + 0 149 0x04 + 0 150 0x04 + 0 151 0x04 >; +}; diff --git a/Documentation/devicetree/bindings/eeprom.txt b/Documentation/devicetree/bindings/eeprom.txt new file mode 100644 index 00000000..4342c10d --- /dev/null +++ b/Documentation/devicetree/bindings/eeprom.txt @@ -0,0 +1,28 @@ +EEPROMs (I2C) + +Required properties: + + - compatible : should be "<manufacturer>,<type>" + If there is no specific driver for <manufacturer>, a generic + driver based on <type> is selected. Possible types are: + 24c00, 24c01, 24c02, 24c04, 24c08, 24c16, 24c32, 24c64, + 24c128, 24c256, 24c512, 24c1024, spd + + - reg : the I2C address of the EEPROM + +Optional properties: + + - pagesize : the length of the pagesize for writing. Please consult the + manual of your device, that value varies a lot. A wrong value + may result in data loss! If not specified, a safety value of + '1' is used which will be very slow. + + - read-only: this parameterless property disables writes to the eeprom + +Example: + +eeprom@52 { + compatible = "atmel,24c32"; + reg = <0x52>; + pagesize = <32>; +}; diff --git a/Documentation/devicetree/bindings/fb/sm501fb.txt b/Documentation/devicetree/bindings/fb/sm501fb.txt new file mode 100644 index 00000000..9d9f0098 --- /dev/null +++ b/Documentation/devicetree/bindings/fb/sm501fb.txt @@ -0,0 +1,34 @@ +* SM SM501 + +The SM SM501 is a LCD controller, with proper hardware, it can also +drive DVI monitors. + +Required properties: +- compatible : should be "smi,sm501". +- reg : contain two entries: + - First entry: System Configuration register + - Second entry: IO space (Display Controller register) +- interrupts : SMI interrupt to the cpu should be described here. +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Optional properties: +- mode : select a video mode: + <xres>x<yres>[-<bpp>][@<refresh>] +- edid : verbatim EDID data block describing attached display. + Data from the detailed timing descriptor will be used to + program the display controller. +- little-endian: available on big endian systems, to + set different foreign endian. +- big-endian: available on little endian systems, to + set different foreign endian. + +Example for MPC5200: + display@1,0 { + compatible = "smi,sm501"; + reg = <1 0x00000000 0x00800000 + 1 0x03e00000 0x00200000>; + interrupts = <1 1 3>; + mode = "640x480-32@60"; + edid = [edid-data]; + }; diff --git a/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt b/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt new file mode 100644 index 00000000..b0019eb5 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt @@ -0,0 +1,60 @@ +GPIO controllers on MPC8xxx SoCs + +This is for the non-QE/CPM/GUTs GPIO controllers as found on +8349, 8572, 8610 and compatible. + +Every GPIO controller node must have #gpio-cells property defined, +this information will be used to translate gpio-specifiers. + +Required properties: +- compatible : "fsl,<CHIP>-gpio" followed by "fsl,mpc8349-gpio" for + 83xx, "fsl,mpc8572-gpio" for 85xx and "fsl,mpc8610-gpio" for 86xx. +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). + - interrupts : Interrupt mapping for GPIO IRQ. + - interrupt-parent : Phandle for the interrupt controller that + services interrupts for this device. +- gpio-controller : Marks the port as GPIO controller. + +Example of gpio-controller nodes for a MPC8347 SoC: + + gpio1: gpio-controller@c00 { + #gpio-cells = <2>; + compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio"; + reg = <0xc00 0x100>; + interrupts = <74 0x8>; + interrupt-parent = <&ipic>; + gpio-controller; + }; + + gpio2: gpio-controller@d00 { + #gpio-cells = <2>; + compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio"; + reg = <0xd00 0x100>; + interrupts = <75 0x8>; + interrupt-parent = <&ipic>; + gpio-controller; + }; + +See booting-without-of.txt for details of how to specify GPIO +information for devices. + +To use GPIO pins as interrupt sources for peripherals, specify the +GPIO controller as the interrupt parent and define GPIO number + +trigger mode using the interrupts property, which is defined like +this: + +interrupts = <number trigger>, where: + - number: GPIO pin (0..31) + - trigger: trigger mode: + 2 = trigger on falling edge + 3 = trigger on both edges + +Example of device using this is: + + funkyfpga@0 { + compatible = "funky-fpga"; + ... + interrupts = <4 3>; + interrupt-parent = <&gpio1>; + }; diff --git a/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt new file mode 100644 index 00000000..4363ae4b --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt @@ -0,0 +1,22 @@ +* Freescale i.MX/MXC GPIO controller + +Required properties: +- compatible : Should be "fsl,<soc>-gpio" +- reg : Address and length of the register set for the device +- interrupts : Should be the port interrupt shared by all 32 pins, if + one number. If two numbers, the first one is the interrupt shared + by low 16 pins and the second one is for high 16 pins. +- gpio-controller : Marks the device node as a gpio controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify optional parameters (currently + unused). + +Example: + +gpio0: gpio@73f84000 { + compatible = "fsl,imx51-gpio", "fsl,imx31-gpio"; + reg = <0x73f84000 0x4000>; + interrupts = <50 51>; + gpio-controller; + #gpio-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-omap.txt b/Documentation/devicetree/bindings/gpio/gpio-omap.txt new file mode 100644 index 00000000..bff51a2f --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-omap.txt @@ -0,0 +1,36 @@ +OMAP GPIO controller bindings + +Required properties: +- compatible: + - "ti,omap2-gpio" for OMAP2 controllers + - "ti,omap3-gpio" for OMAP3 controllers + - "ti,omap4-gpio" for OMAP4 controllers +- #gpio-cells : Should be two. + - first cell is the pin number + - second cell is used to specify optional parameters (unused) +- gpio-controller : Marks the device node as a GPIO controller. +- #interrupt-cells : Should be 2. +- interrupt-controller: Mark the device node as an interrupt controller + The first cell is the GPIO number. + The second cell is used to specify flags: + bits[3:0] trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. + +OMAP specific properties: +- ti,hwmods: Name of the hwmod associated to the GPIO: + "gpio<X>", <X> being the 1-based instance number from the HW spec + + +Example: + +gpio4: gpio4 { + compatible = "ti,omap4-gpio"; + ti,hwmods = "gpio4"; + #gpio-cells = <2>; + gpio-controller; + #interrupt-cells = <2>; + interrupt-controller; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-samsung.txt b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt new file mode 100644 index 00000000..8f50fe5e --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt @@ -0,0 +1,40 @@ +Samsung Exynos4 GPIO Controller + +Required properties: +- compatible: Compatible property value should be "samsung,exynos4-gpio>". + +- reg: Physical base address of the controller and length of memory mapped + region. + +- #gpio-cells: Should be 4. The syntax of the gpio specifier used by client nodes + should be the following with values derived from the SoC user manual. + <[phandle of the gpio controller node] + [pin number within the gpio controller] + [mux function] + [pull up/down] + [drive strength]> + + Values for gpio specifier: + - Pin number: is a value between 0 to 7. + - Pull Up/Down: 0 - Pull Up/Down Disabled. + 1 - Pull Down Enabled. + 3 - Pull Up Enabled. + - Drive Strength: 0 - 1x, + 1 - 3x, + 2 - 2x, + 3 - 4x + +- gpio-controller: Specifies that the node is a gpio controller. +- #address-cells: should be 1. +- #size-cells: should be 1. + +Example: + + gpa0: gpio-controller@11400000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "samsung,exynos4-gpio"; + reg = <0x11400000 0x20>; + #gpio-cells = <4>; + gpio-controller; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt b/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt new file mode 100644 index 00000000..16695d9c --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt @@ -0,0 +1,23 @@ +twl4030 GPIO controller bindings + +Required properties: +- compatible: + - "ti,twl4030-gpio" for twl4030 GPIO controller +- #gpio-cells : Should be two. + - first cell is the pin number + - second cell is used to specify optional parameters (unused) +- gpio-controller : Marks the device node as a GPIO controller. +- #interrupt-cells : Should be 2. +- interrupt-controller: Mark the device node as an interrupt controller + The first cell is the GPIO number. + The second cell is not used. + +Example: + +twl_gpio: gpio { + compatible = "ti,twl4030-gpio"; + #gpio-cells = <2>; + gpio-controller; + #interrupt-cells = <2>; + interrupt-controller; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt new file mode 100644 index 00000000..4e16ba4f --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -0,0 +1,78 @@ +Specifying GPIO information for devices +============================================ + +1) gpios property +----------------- + +Nodes that makes use of GPIOs should specify them using one or more +properties, each containing a 'gpio-list': + + gpio-list ::= <single-gpio> [gpio-list] + single-gpio ::= <gpio-phandle> <gpio-specifier> + gpio-phandle : phandle to gpio controller node + gpio-specifier : Array of #gpio-cells specifying specific gpio + (controller specific) + +GPIO properties should be named "[<name>-]gpios". Exact +meaning of each gpios property must be documented in the device tree +binding for each device. + +For example, the following could be used to describe gpios pins to use +as chip select lines; with chip selects 0, 1 and 3 populated, and chip +select 2 left empty: + + gpio1: gpio1 { + gpio-controller + #gpio-cells = <2>; + }; + gpio2: gpio2 { + gpio-controller + #gpio-cells = <1>; + }; + [...] + chipsel-gpios = <&gpio1 12 0>, + <&gpio1 13 0>, + <0>, /* holes are permitted, means no GPIO 2 */ + <&gpio2 2>; + +Note that gpio-specifier length is controller dependent. In the +above example, &gpio1 uses 2 cells to specify a gpio, while &gpio2 +only uses one. + +gpio-specifier may encode: bank, pin position inside the bank, +whether pin is open-drain and whether pin is logically inverted. +Exact meaning of each specifier cell is controller specific, and must +be documented in the device tree binding for the device. + +Example of the node using GPIOs: + + node { + gpios = <&qe_pio_e 18 0>; + }; + +In this example gpio-specifier is "18 0" and encodes GPIO pin number, +and empty GPIO flags as accepted by the "qe_pio_e" gpio-controller. + +2) gpio-controller nodes +------------------------ + +Every GPIO controller node must both an empty "gpio-controller" +property, and have #gpio-cells contain the size of the gpio-specifier. + +Example of two SOC GPIO banks defined as gpio-controller nodes: + + qe_pio_a: gpio-controller@1400 { + #gpio-cells = <2>; + compatible = "fsl,qe-pario-bank-a", "fsl,qe-pario-bank"; + reg = <0x1400 0x18>; + gpio-controller; + }; + + qe_pio_e: gpio-controller@1460 { + #gpio-cells = <2>; + compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; + reg = <0x1460 0x18>; + gpio-controller; + }; + + diff --git a/Documentation/devicetree/bindings/gpio/gpio_atmel.txt b/Documentation/devicetree/bindings/gpio/gpio_atmel.txt new file mode 100644 index 00000000..66efc804 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio_atmel.txt @@ -0,0 +1,20 @@ +* Atmel GPIO controller (PIO) + +Required properties: +- compatible: "atmel,<chip>-gpio", where <chip> is at91rm9200 or at91sam9x5. +- reg: Should contain GPIO controller registers location and length +- interrupts: Should be the port interrupt shared by all the pins. +- #gpio-cells: Should be two. The first cell is the pin number and + the second cell is used to specify optional parameters (currently + unused). +- gpio-controller: Marks the device node as a GPIO controller. + +Example: + pioA: gpio@fffff200 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff200 0x100>; + interrupts = <2 4>; + #gpio-cells = <2>; + gpio-controller; + }; + diff --git a/Documentation/devicetree/bindings/gpio/gpio_i2c.txt b/Documentation/devicetree/bindings/gpio/gpio_i2c.txt new file mode 100644 index 00000000..4f8ec947 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio_i2c.txt @@ -0,0 +1,32 @@ +Device-Tree bindings for i2c gpio driver + +Required properties: + - compatible = "i2c-gpio"; + - gpios: sda and scl gpio + + +Optional properties: + - i2c-gpio,sda-open-drain: sda as open drain + - i2c-gpio,scl-open-drain: scl as open drain + - i2c-gpio,scl-output-only: scl as output only + - i2c-gpio,delay-us: delay between GPIO operations (may depend on each platform) + - i2c-gpio,timeout-ms: timeout to get data + +Example nodes: + +i2c@0 { + compatible = "i2c-gpio"; + gpios = <&pioA 23 0 /* sda */ + &pioA 24 0 /* scl */ + >; + i2c-gpio,sda-open-drain; + i2c-gpio,scl-open-drain; + i2c-gpio,delay-us = <2>; /* ~100 kHz */ + #address-cells = <1>; + #size-cells = <0>; + + rv3029c2@56 { + compatible = "rv3029c2"; + reg = <0x56>; + }; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio_keys.txt b/Documentation/devicetree/bindings/gpio/gpio_keys.txt new file mode 100644 index 00000000..5c2c0214 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio_keys.txt @@ -0,0 +1,36 @@ +Device-Tree bindings for input/gpio_keys.c keyboard driver + +Required properties: + - compatible = "gpio-keys"; + +Optional properties: + - autorepeat: Boolean, Enable auto repeat feature of Linux input + subsystem. + +Each button (key) is represented as a sub-node of "gpio-keys": +Subnode properties: + + - gpios: OF device-tree gpio specification. + - label: Descriptive name of the key. + - linux,code: Keycode to emit. + +Optional subnode-properties: + - linux,input-type: Specify event type this button/key generates. + If not specified defaults to <1> == EV_KEY. + - debounce-interval: Debouncing interval time in milliseconds. + If not specified defaults to 5. + - gpio-key,wakeup: Boolean, button can wake-up the system. + +Example nodes: + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + autorepeat; + button@21 { + label = "GPIO Key UP"; + linux,code = <103>; + gpios = <&gpio1 0 1>; + }; + ... diff --git a/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt b/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt new file mode 100644 index 00000000..023c9526 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt @@ -0,0 +1,40 @@ +NVIDIA Tegra GPIO controller + +Required properties: +- compatible : "nvidia,tegra<chip>-gpio" +- reg : Physical base address and length of the controller's registers. +- interrupts : The interrupt outputs from the controller. For Tegra20, + there should be 7 interrupts specified, and for Tegra30, there should + be 8 interrupts specified. +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters: + - bit 0 specifies polarity (0 for normal, 1 for inverted) +- gpio-controller : Marks the device node as a GPIO controller. +- #interrupt-cells : Should be 2. + The first cell is the GPIO number. + The second cell is used to specify flags: + bits[3:0] trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. + Valid combinations are 1, 2, 3, 4, 8. +- interrupt-controller : Marks the device node as an interrupt controller. + +Example: + +gpio: gpio@6000d000 { + compatible = "nvidia,tegra20-gpio"; + reg = < 0x6000d000 0x1000 >; + interrupts = < 0 32 0x04 + 0 33 0x04 + 0 34 0x04 + 0 35 0x04 + 0 55 0x04 + 0 87 0x04 + 0 89 0x04 >; + #gpio-cells = <2>; + gpio-controller; + #interrupt-cells = <2>; + interrupt-controller; +}; diff --git a/Documentation/devicetree/bindings/gpio/led.txt b/Documentation/devicetree/bindings/gpio/led.txt new file mode 100644 index 00000000..fd2bd56e --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/led.txt @@ -0,0 +1,58 @@ +LEDs connected to GPIO lines + +Required properties: +- compatible : should be "gpio-leds". + +Each LED is represented as a sub-node of the gpio-leds device. Each +node's name represents the name of the corresponding LED. + +LED sub-node properties: +- gpios : Should specify the LED's GPIO, see "gpios property" in + Documentation/devicetree/gpio.txt. Active low LEDs should be + indicated using flags in the GPIO specifier. +- label : (optional) The label for this LED. If omitted, the label is + taken from the node name (excluding the unit address). +- linux,default-trigger : (optional) This parameter, if present, is a + string defining the trigger assigned to the LED. Current triggers are: + "backlight" - LED will act as a back-light, controlled by the framebuffer + system + "default-on" - LED will turn on, but see "default-state" below + "heartbeat" - LED "double" flashes at a load average based rate + "ide-disk" - LED indicates disk activity + "timer" - LED flashes at a fixed, configurable rate +- default-state: (optional) The initial state of the LED. Valid + values are "on", "off", and "keep". If the LED is already on or off + and the default-state property is set the to same value, then no + glitch should be produced where the LED momentarily turns off (or + on). The "keep" setting will keep the LED at whatever its current + state is, without producing a glitch. The default is off if this + property is not present. + +Examples: + +leds { + compatible = "gpio-leds"; + hdd { + label = "IDE Activity"; + gpios = <&mcu_pio 0 1>; /* Active low */ + linux,default-trigger = "ide-disk"; + }; + + fault { + gpios = <&mcu_pio 1 0>; + /* Keep LED on if BIOS detected hardware fault */ + default-state = "keep"; + }; +}; + +run-control { + compatible = "gpio-leds"; + red { + gpios = <&mpc8572 6 0>; + default-state = "off"; + }; + green { + gpios = <&mpc8572 7 0>; + default-state = "on"; + }; +} diff --git a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt new file mode 100644 index 00000000..1e34cfe5 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt @@ -0,0 +1,23 @@ +* Marvell PXA GPIO controller + +Required properties: +- compatible : Should be "mrvl,pxa-gpio" or "mrvl,mmp-gpio" +- reg : Address and length of the register set for the device +- interrupts : Should be the port interrupt shared by all gpio pins, if +- interrupt-name : Should be the name of irq resource. + one number. +- gpio-controller : Marks the device node as a gpio controller. +- #gpio-cells : Should be one. It is the pin number. + +Example: + + gpio: gpio@d4019000 { + compatible = "mrvl,mmp-gpio", "mrvl,pxa-gpio"; + reg = <0xd4019000 0x1000>; + interrupts = <49>, <17>, <18>; + interrupt-name = "gpio_mux", "gpio0", "gpio1"; + gpio-controller; + #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/gpio/pl061-gpio.txt b/Documentation/devicetree/bindings/gpio/pl061-gpio.txt new file mode 100644 index 00000000..a2c416bc --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/pl061-gpio.txt @@ -0,0 +1,10 @@ +ARM PL061 GPIO controller + +Required properties: +- compatible : "arm,pl061", "arm,primecell" +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters: + - bit 0 specifies polarity (0 for normal, 1 for inverted) +- gpio-controller : Marks the device node as a GPIO controller. +- interrupts : Interrupt mapping for GPIO IRQ. + diff --git a/Documentation/devicetree/bindings/gpio/sodaville.txt b/Documentation/devicetree/bindings/gpio/sodaville.txt new file mode 100644 index 00000000..563eff22 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/sodaville.txt @@ -0,0 +1,48 @@ +GPIO controller on CE4100 / Sodaville SoCs +========================================== + +The bindings for CE4100's GPIO controller match the generic description +which is covered by the gpio.txt file in this folder. + +The only additional property is the intel,muxctl property which holds the +value which is written into the MUXCNTL register. + +There is no compatible property for now because the driver is probed via +PCI id (vendor 0x8086 device 0x2e67). + +The interrupt specifier consists of two cells encoded as follows: + - <1st cell>: The interrupt-number that identifies the interrupt source. + - <2nd cell>: The level-sense information, encoded as follows: + 4 - active high level-sensitive + 8 - active low level-sensitive + +Example of the GPIO device and one user: + + pcigpio: gpio@b,1 { + /* two cells for GPIO and interrupt */ + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "pci8086,2e67.2", + "pci8086,2e67", + "pciclassff0000", + "pciclassff00"; + + reg = <0x15900 0x0 0x0 0x0 0x0>; + /* Interrupt line of the gpio device */ + interrupts = <15 1>; + /* It is an interrupt and GPIO controller itself */ + interrupt-controller; + gpio-controller; + intel,muxctl = <0>; + }; + + testuser@20 { + compatible = "example,testuser"; + /* User the 11th GPIO line as an active high triggered + * level interrupt + */ + interrupts = <11 8>; + interrupt-parent = <&pcigpio>; + /* Use this GPIO also with the gpio functions */ + gpios = <&pcigpio 11 0>; + }; diff --git a/Documentation/devicetree/bindings/hwmon/ads1015.txt b/Documentation/devicetree/bindings/hwmon/ads1015.txt new file mode 100644 index 00000000..918a507d --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/ads1015.txt @@ -0,0 +1,73 @@ +ADS1015 (I2C) + +This device is a 12-bit A-D converter with 4 inputs. + +The inputs can be used single ended or in certain differential combinations. + +For configuration all possible combinations are mapped to 8 channels: + 0: Voltage over AIN0 and AIN1. + 1: Voltage over AIN0 and AIN3. + 2: Voltage over AIN1 and AIN3. + 3: Voltage over AIN2 and AIN3. + 4: Voltage over AIN0 and GND. + 5: Voltage over AIN1 and GND. + 6: Voltage over AIN2 and GND. + 7: Voltage over AIN3 and GND. + +Each channel can be configured individually: + - pga is the programmable gain amplifier (values are full scale) + 0: +/- 6.144 V + 1: +/- 4.096 V + 2: +/- 2.048 V (default) + 3: +/- 1.024 V + 4: +/- 0.512 V + 5: +/- 0.256 V + - data_rate in samples per second + 0: 128 + 1: 250 + 2: 490 + 3: 920 + 4: 1600 (default) + 5: 2400 + 6: 3300 + +1) The /ads1015 node + + Required properties: + + - compatible : must be "ti,ads1015" + - reg : I2C bus address of the device + - #address-cells : must be <1> + - #size-cells : must be <0> + + The node contains child nodes for each channel that the platform uses. + + Example ADS1015 node: + + ads1015@49 { + compatible = "ti,ads1015"; + reg = <0x49>; + #address-cells = <1>; + #size-cells = <0>; + + [ child node definitions... ] + } + +2) channel nodes + + Required properties: + + - reg : the channel number + + Optional properties: + + - ti,gain : the programmable gain amplifier setting + - ti,datarate : the converter data rate + + Example ADS1015 channel node: + + channel@4 { + reg = <4>; + ti,gain = <3>; + ti,datarate = <5>; + }; diff --git a/Documentation/devicetree/bindings/i2c/arm-versatile.txt b/Documentation/devicetree/bindings/i2c/arm-versatile.txt new file mode 100644 index 00000000..361d31c5 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/arm-versatile.txt @@ -0,0 +1,10 @@ +i2c Controller on ARM Versatile platform: + +Required properties: +- compatible : Must be "arm,versatile-i2c"; +- reg +- #address-cells = <1>; +- #size-cells = <0>; + +Optional properties: +- Child nodes conforming to i2c bus binding diff --git a/Documentation/devicetree/bindings/i2c/ce4100-i2c.txt b/Documentation/devicetree/bindings/i2c/ce4100-i2c.txt new file mode 100644 index 00000000..569b1624 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/ce4100-i2c.txt @@ -0,0 +1,93 @@ +CE4100 I2C +---------- + +CE4100 has one PCI device which is described as the I2C-Controller. This +PCI device has three PCI-bars, each bar contains a complete I2C +controller. So we have a total of three independent I2C-Controllers +which share only an interrupt line. +The driver is probed via the PCI-ID and is gathering the information of +attached devices from the devices tree. +Grant Likely recommended to use the ranges property to map the PCI-Bar +number to its physical address and to use this to find the child nodes +of the specific I2C controller. This were his exact words: + + Here's where the magic happens. Each entry in + ranges describes how the parent pci address space + (middle group of 3) is translated to the local + address space (first group of 2) and the size of + each range (last cell). In this particular case, + the first cell of the local address is chosen to be + 1:1 mapped to the BARs, and the second is the + offset from be base of the BAR (which would be + non-zero if you had 2 or more devices mapped off + the same BAR) + + ranges allows the address mapping to be described + in a way that the OS can interpret without + requiring custom device driver code. + +This is an example which is used on FalconFalls: +------------------------------------------------ + i2c-controller@b,2 { + #address-cells = <2>; + #size-cells = <1>; + compatible = "pci8086,2e68.2", + "pci8086,2e68", + "pciclass,ff0000", + "pciclass,ff00"; + + reg = <0x15a00 0x0 0x0 0x0 0x0>; + interrupts = <16 1>; + + /* as described by Grant, the first number in the group of + * three is the bar number followed by the 64bit bar address + * followed by size of the mapping. The bar address + * requires also a valid translation in parents ranges + * property. + */ + ranges = <0 0 0x02000000 0 0xdffe0500 0x100 + 1 0 0x02000000 0 0xdffe0600 0x100 + 2 0 0x02000000 0 0xdffe0700 0x100>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "intel,ce4100-i2c-controller"; + + /* The first number in the reg property is the + * number of the bar + */ + reg = <0 0 0x100>; + + /* This I2C controller has no devices */ + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "intel,ce4100-i2c-controller"; + reg = <1 0 0x100>; + + /* This I2C controller has one gpio controller */ + gpio@26 { + #gpio-cells = <2>; + compatible = "ti,pcf8575"; + reg = <0x26>; + gpio-controller; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "intel,ce4100-i2c-controller"; + reg = <2 0 0x100>; + + gpio@26 { + #gpio-cells = <2>; + compatible = "ti,pcf8575"; + reg = <0x26>; + gpio-controller; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/fsl-i2c.txt b/Documentation/devicetree/bindings/i2c/fsl-i2c.txt new file mode 100644 index 00000000..1eacd6b2 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/fsl-i2c.txt @@ -0,0 +1,64 @@ +* I2C + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : should be "fsl,CHIP-i2c" where CHIP is the name of a + compatible processor, e.g. mpc8313, mpc8543, mpc8544, mpc5121, + mpc5200 or mpc5200b. For the mpc5121, an additional node + "fsl,mpc5121-i2c-ctrl" is required as shown in the example below. + +Recommended properties : + + - interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + - fsl,preserve-clocking : boolean; if defined, the clock settings + from the bootloader are preserved (not touched). + - clock-frequency : desired I2C bus clock frequency in Hz. + - fsl,timeout : I2C bus timeout in microseconds. + +Examples : + + /* MPC5121 based board */ + i2c@1740 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5121-i2c", "fsl-i2c"; + reg = <0x1740 0x20>; + interrupts = <11 0x8>; + interrupt-parent = <&ipic>; + clock-frequency = <100000>; + }; + + i2ccontrol@1760 { + compatible = "fsl,mpc5121-i2c-ctrl"; + reg = <0x1760 0x8>; + }; + + /* MPC5200B based board */ + i2c@3d00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; + reg = <0x3d00 0x40>; + interrupts = <2 15 0>; + interrupt-parent = <&mpc5200_pic>; + fsl,preserve-clocking; + }; + + /* MPC8544 base board */ + i2c@3100 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc8544-i2c", "fsl-i2c"; + reg = <0x3100 0x100>; + interrupts = <43 2>; + interrupt-parent = <&mpic>; + clock-frequency = <400000>; + fsl,timeout = <10000>; + }; diff --git a/Documentation/devicetree/bindings/i2c/fsl-imx-i2c.txt b/Documentation/devicetree/bindings/i2c/fsl-imx-i2c.txt new file mode 100644 index 00000000..f3cf43b6 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/fsl-imx-i2c.txt @@ -0,0 +1,25 @@ +* Freescale Inter IC (I2C) and High Speed Inter IC (HS-I2C) for i.MX + +Required properties: +- compatible : Should be "fsl,<chip>-i2c" +- reg : Should contain I2C/HS-I2C registers location and length +- interrupts : Should contain I2C/HS-I2C interrupt + +Optional properties: +- clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz. + The absence of the propoerty indicates the default frequency 100 kHz. + +Examples: + +i2c@83fc4000 { /* I2C2 on i.MX51 */ + compatible = "fsl,imx51-i2c", "fsl,imx1-i2c"; + reg = <0x83fc4000 0x4000>; + interrupts = <63>; +}; + +i2c@70038000 { /* HS-I2C on i.MX51 */ + compatible = "fsl,imx51-i2c", "fsl,imx1-i2c"; + reg = <0x70038000 0x4000>; + interrupts = <64>; + clock-frequency = <400000>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-designware.txt b/Documentation/devicetree/bindings/i2c/i2c-designware.txt new file mode 100644 index 00000000..e42a2ee2 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-designware.txt @@ -0,0 +1,22 @@ +* Synopsys DesignWare I2C + +Required properties : + + - compatible : should be "snps,designware-i2c" + - reg : Offset and length of the register set for the device + - interrupts : <IRQ> where IRQ is the interrupt number. + +Recommended properties : + + - clock-frequency : desired I2C bus clock frequency in Hz. + +Example : + + i2c@f0000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,designware-i2c"; + reg = <0xf0000 0x1000>; + interrupts = <11>; + clock-frequency = <400000>; + }; diff --git a/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt b/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt new file mode 100644 index 00000000..071eb3ca --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt @@ -0,0 +1,37 @@ +* I2C + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : should be "mrvl,mmp-twsi" where CHIP is the name of a + compatible processor, e.g. pxa168, pxa910, mmp2, mmp3. + For the pxa2xx/pxa3xx, an additional node "mrvl,pxa-i2c" is required + as shown in the example below. + +Recommended properties : + + - interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + - mrvl,i2c-polling : Disable interrupt of i2c controller. Polling + status register of i2c controller instead. + - mrvl,i2c-fast-mode : Enable fast mode of i2c controller. + +Examples: + twsi1: i2c@d4011000 { + compatible = "mrvl,mmp-twsi", "mrvl,pxa-i2c"; + reg = <0xd4011000 0x1000>; + interrupts = <7>; + mrvl,i2c-fast-mode; + }; + + twsi2: i2c@d4025000 { + compatible = "mrvl,mmp-twsi", "mrvl,pxa-i2c"; + reg = <0xd4025000 0x1000>; + interrupts = <58>; + }; + diff --git a/Documentation/devicetree/bindings/i2c/omap-i2c.txt b/Documentation/devicetree/bindings/i2c/omap-i2c.txt new file mode 100644 index 00000000..56564aa4 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/omap-i2c.txt @@ -0,0 +1,30 @@ +I2C for OMAP platforms + +Required properties : +- compatible : Must be "ti,omap3-i2c" or "ti,omap4-i2c" +- ti,hwmods : Must be "i2c<n>", n being the instance number (1-based) +- #address-cells = <1>; +- #size-cells = <0>; + +Recommended properties : +- clock-frequency : Desired I2C bus clock frequency in Hz. Otherwise + the default 100 kHz frequency will be used. + +Optional properties: +- Child nodes conforming to i2c bus binding + +Note: Current implementation will fetch base address, irq and dma +from omap hwmod data base during device registration. +Future plan is to migrate hwmod data base contents into device tree +blob so that, all the required data will be used from device tree dts +file. + +Examples : + +i2c1: i2c@0 { + compatible = "ti,omap3-i2c"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "i2c1"; + clock-frequency = <400000>; +}; diff --git a/Documentation/devicetree/bindings/i2c/samsung-i2c.txt b/Documentation/devicetree/bindings/i2c/samsung-i2c.txt new file mode 100644 index 00000000..38832c71 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/samsung-i2c.txt @@ -0,0 +1,39 @@ +* Samsung's I2C controller + +The Samsung's I2C controller is used to interface with I2C devices. + +Required properties: + - compatible: value should be either of the following. + (a) "samsung, s3c2410-i2c", for i2c compatible with s3c2410 i2c. + (b) "samsung, s3c2440-i2c", for i2c compatible with s3c2440 i2c. + - reg: physical base address of the controller and length of memory mapped + region. + - interrupts: interrupt number to the cpu. + - samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges. + - gpios: The order of the gpios should be the following: <SDA, SCL>. + The gpio specifier depends on the gpio controller. + +Optional properties: + - samsung,i2c-slave-addr: Slave address in multi-master enviroment. If not + specified, default value is 0. + - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not + specified, the default value in Hz is 100000. + +Example: + + i2c@13870000 { + compatible = "samsung,s3c2440-i2c"; + reg = <0x13870000 0x100>; + interrupts = <345>; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <100000>; + gpios = <&gpd1 2 0 /* SDA */ + &gpd1 3 0 /* SCL */>; + #address-cells = <1>; + #size-cells = <0>; + + wm8994@1a { + compatible = "wlf,wm8994"; + reg = <0x1a>; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/sirf-i2c.txt b/Documentation/devicetree/bindings/i2c/sirf-i2c.txt new file mode 100644 index 00000000..7baf9e13 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/sirf-i2c.txt @@ -0,0 +1,19 @@ +I2C for SiRFprimaII platforms + +Required properties : +- compatible : Must be "sirf,prima2-i2c" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: interrupt number to the cpu. + +Optional properties: +- clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz. + The absence of the propoerty indicates the default frequency 100 kHz. + +Examples : + +i2c0: i2c@b00e0000 { + compatible = "sirf,prima2-i2c"; + reg = <0xb00e0000 0x10000>; + interrupts = <24>; +}; diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt new file mode 100644 index 00000000..1a85f986 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -0,0 +1,58 @@ +This is a list of trivial i2c devices that have simple device tree +bindings, consisting only of a compatible field, an address and +possibly an interrupt line. + +If a device needs more specific bindings, such as properties to +describe some aspect of it, there needs to be a specific binding +document for it just like any other devices. + + +Compatible Vendor / Chip +========== ============= +ad,ad7414 SMBus/I2C Digital Temperature Sensor in 6-Pin SOT with SMBus Alert and Over Temperature Pin +ad,adm9240 ADM9240: Complete System Hardware Monitor for uProcessor-Based Systems +adi,adt7461 +/-1C TDM Extended Temp Range I.C +adt7461 +/-1C TDM Extended Temp Range I.C +at,24c08 i2c serial eeprom (24cxx) +atmel,24c02 i2c serial eeprom (24cxx) +catalyst,24c32 i2c serial eeprom +dallas,ds1307 64 x 8, Serial, I2C Real-Time Clock +dallas,ds1338 I2C RTC with 56-Byte NV RAM +dallas,ds1339 I2C Serial Real-Time Clock +dallas,ds1340 I2C RTC with Trickle Charger +dallas,ds1374 I2C, 32-Bit Binary Counter Watchdog RTC with Trickle Charger and Reset Input/Output +dallas,ds1631 High-Precision Digital Thermometer +dallas,ds1682 Total-Elapsed-Time Recorder with Alarm +dallas,ds1775 Tiny Digital Thermometer and Thermostat +dallas,ds3232 Extremely Accurate I²C RTC with Integrated Crystal and SRAM +dallas,ds4510 CPU Supervisor with Nonvolatile Memory and Programmable I/O +dallas,ds75 Digital Thermometer and Thermostat +dialog,da9053 DA9053: flexible system level PMIC with multicore support +epson,rx8025 High-Stability. I2C-Bus INTERFACE REAL TIME CLOCK MODULE +epson,rx8581 I2C-BUS INTERFACE REAL TIME CLOCK MODULE +fsl,mag3110 MAG3110: Xtrinsic High Accuracy, 3D Magnetometer +fsl,mc13892 MC13892: Power Management Integrated Circuit (PMIC) for i.MX35/51 +fsl,mma8450 MMA8450Q: Xtrinsic Low-power, 3-axis Xtrinsic Accelerometer +fsl,mpr121 MPR121: Proximity Capacitive Touch Sensor Controller +fsl,sgtl5000 SGTL5000: Ultra Low-Power Audio Codec +maxim,ds1050 5 Bit Programmable, Pulse-Width Modulator +maxim,max1237 Low-Power, 4-/12-Channel, 2-Wire Serial, 12-Bit ADCs +maxim,max6625 9-Bit/12-Bit Temperature Sensors with I²C-Compatible Serial Interface +mc,rv3029c2 Real Time Clock Module with I2C-Bus +national,lm75 I2C TEMP SENSOR +national,lm80 Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor +national,lm92 ±0.33°C Accurate, 12-Bit + Sign Temperature Sensor and Thermal Window Comparator with Two-Wire Interface +nxp,pca9556 Octal SMBus and I2C registered interface +nxp,pca9557 8-bit I2C-bus and SMBus I/O port with reset +nxp,pcf8563 Real-time clock/calendar +ovti,ov5642 OV5642: Color CMOS QSXGA (5-megapixel) Image Sensor with OmniBSI and Embedded TrueFocus +pericom,pt7c4338 Real-time Clock Module +plx,pex8648 48-Lane, 12-Port PCI Express Gen 2 (5.0 GT/s) Switch +ramtron,24c64 i2c serial eeprom (24cxx) +ricoh,rs5c372a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC +samsung,24ad0xd1 S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power) +st-micro,24c256 i2c serial eeprom (24cxx) +stm,m41t00 Serial Access TIMEKEEPER +stm,m41t62 Serial real-time clock (RTC) with alarm +stm,m41t80 M41T80 - SERIAL ACCESS RTC WITH ALARMS +ti,tsc2003 I2C Touch-Screen Controller diff --git a/Documentation/devicetree/bindings/input/fsl-mma8450.txt b/Documentation/devicetree/bindings/input/fsl-mma8450.txt new file mode 100644 index 00000000..a00c94cc --- /dev/null +++ b/Documentation/devicetree/bindings/input/fsl-mma8450.txt @@ -0,0 +1,11 @@ +* Freescale MMA8450 3-Axis Accelerometer + +Required properties: +- compatible : "fsl,mma8450". + +Example: + +accelerometer: mma8450@1c { + compatible = "fsl,mma8450"; + reg = <0x1c>; +}; diff --git a/Documentation/devicetree/bindings/input/matrix-keymap.txt b/Documentation/devicetree/bindings/input/matrix-keymap.txt new file mode 100644 index 00000000..3cd8b98c --- /dev/null +++ b/Documentation/devicetree/bindings/input/matrix-keymap.txt @@ -0,0 +1,19 @@ +A simple common binding for matrix-connected key boards. Currently targeted at +defining the keys in the scope of linux key codes since that is a stable and +standardized interface at this time. + +Required properties: +- linux,keymap: an array of packed 1-cell entries containing the equivalent + of row, column and linux key-code. The 32-bit big endian cell is packed + as: + row << 24 | column << 16 | key-code + +Optional properties: +Some users of this binding might choose to specify secondary keymaps for +cases where there is a modifier key such as a Fn key. Proposed names +for said properties are "linux,fn-keymap" or with another descriptive +word for the modifier other from "Fn". + +Example: + linux,keymap = < 0x00030012 + 0x0102003a >; diff --git a/Documentation/devicetree/bindings/input/samsung-keypad.txt b/Documentation/devicetree/bindings/input/samsung-keypad.txt new file mode 100644 index 00000000..ce3e394c --- /dev/null +++ b/Documentation/devicetree/bindings/input/samsung-keypad.txt @@ -0,0 +1,88 @@ +* Samsung's Keypad Controller device tree bindings + +Samsung's Keypad controller is used to interface a SoC with a matrix-type +keypad device. The keypad controller supports multiple row and column lines. +A key can be placed at each intersection of a unique row and a unique column. +The keypad controller can sense a key-press and key-release and report the +event using a interrupt to the cpu. + +Required SoC Specific Properties: +- compatible: should be one of the following + - "samsung,s3c6410-keypad": For controllers compatible with s3c6410 keypad + controller. + - "samsung,s5pv210-keypad": For controllers compatible with s5pv210 keypad + controller. + +- reg: physical base address of the controller and length of memory mapped + region. + +- interrupts: The interrupt number to the cpu. + +Required Board Specific Properties: +- samsung,keypad-num-rows: Number of row lines connected to the keypad + controller. + +- samsung,keypad-num-columns: Number of column lines connected to the + keypad controller. + +- row-gpios: List of gpios used as row lines. The gpio specifier for + this property depends on the gpio controller to which these row lines + are connected. + +- col-gpios: List of gpios used as column lines. The gpio specifier for + this property depends on the gpio controller to which these column + lines are connected. + +- Keys represented as child nodes: Each key connected to the keypad + controller is represented as a child node to the keypad controller + device node and should include the following properties. + - keypad,row: the row number to which the key is connected. + - keypad,column: the column number to which the key is connected. + - linux,code: the key-code to be reported when the key is pressed + and released. + +Optional Properties specific to linux: +- linux,keypad-no-autorepeat: do no enable autorepeat feature. +- linux,keypad-wakeup: use any event on keypad as wakeup event. + + +Example: + keypad@100A0000 { + compatible = "samsung,s5pv210-keypad"; + reg = <0x100A0000 0x100>; + interrupts = <173>; + samsung,keypad-num-rows = <2>; + samsung,keypad-num-columns = <8>; + linux,input-no-autorepeat; + linux,input-wakeup; + + row-gpios = <&gpx2 0 3 3 0 + &gpx2 1 3 3 0>; + + col-gpios = <&gpx1 0 3 0 0 + &gpx1 1 3 0 0 + &gpx1 2 3 0 0 + &gpx1 3 3 0 0 + &gpx1 4 3 0 0 + &gpx1 5 3 0 0 + &gpx1 6 3 0 0 + &gpx1 7 3 0 0>; + + key_1 { + keypad,row = <0>; + keypad,column = <3>; + linux,code = <2>; + }; + + key_2 { + keypad,row = <0>; + keypad,column = <4>; + linux,code = <3>; + }; + + key_3 { + keypad,row = <0>; + keypad,column = <5>; + linux,code = <4>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/tegra-kbc.txt b/Documentation/devicetree/bindings/input/tegra-kbc.txt new file mode 100644 index 00000000..72683be6 --- /dev/null +++ b/Documentation/devicetree/bindings/input/tegra-kbc.txt @@ -0,0 +1,23 @@ +* Tegra keyboard controller + +Required properties: +- compatible: "nvidia,tegra20-kbc" + +Optional properties, in addition to those specified by the shared +matrix-keyboard bindings: + +- linux,fn-keymap: a second keymap, same specification as the + matrix-keyboard-controller spec but to be used when the KEY_FN modifier + key is pressed. +- nvidia,debounce-delay-ms: delay in milliseconds per row scan for debouncing +- nvidia,repeat-delay-ms: delay in milliseconds before repeat starts +- nvidia,ghost-filter: enable ghost filtering for this device +- nvidia,wakeup-source: configure keyboard as a wakeup source for suspend/resume + +Example: + +keyboard: keyboard { + compatible = "nvidia,tegra20-kbc"; + reg = <0x7000e200 0x100>; + nvidia,ghost-filter; +}; diff --git a/Documentation/devicetree/bindings/marvell.txt b/Documentation/devicetree/bindings/marvell.txt new file mode 100644 index 00000000..f1533d91 --- /dev/null +++ b/Documentation/devicetree/bindings/marvell.txt @@ -0,0 +1,521 @@ +Marvell Discovery mv64[345]6x System Controller chips +=========================================================== + +The Marvell mv64[345]60 series of system controller chips contain +many of the peripherals needed to implement a complete computer +system. In this section, we define device tree nodes to describe +the system controller chip itself and each of the peripherals +which it contains. Compatible string values for each node are +prefixed with the string "marvell,", for Marvell Technology Group Ltd. + +1) The /system-controller node + + This node is used to represent the system-controller and must be + present when the system uses a system controller chip. The top-level + system-controller node contains information that is global to all + devices within the system controller chip. The node name begins + with "system-controller" followed by the unit address, which is + the base address of the memory-mapped register set for the system + controller chip. + + Required properties: + + - ranges : Describes the translation of system controller addresses + for memory mapped registers. + - clock-frequency: Contains the main clock frequency for the system + controller chip. + - reg : This property defines the address and size of the + memory-mapped registers contained within the system controller + chip. The address specified in the "reg" property should match + the unit address of the system-controller node. + - #address-cells : Address representation for system controller + devices. This field represents the number of cells needed to + represent the address of the memory-mapped registers of devices + within the system controller chip. + - #size-cells : Size representation for the memory-mapped + registers within the system controller chip. + - #interrupt-cells : Defines the width of cells used to represent + interrupts. + + Optional properties: + + - model : The specific model of the system controller chip. Such + as, "mv64360", "mv64460", or "mv64560". + - compatible : A string identifying the compatibility identifiers + of the system controller chip. + + The system-controller node contains child nodes for each system + controller device that the platform uses. Nodes should not be created + for devices which exist on the system controller chip but are not used + + Example Marvell Discovery mv64360 system-controller node: + + system-controller@f1000000 { /* Marvell Discovery mv64360 */ + #address-cells = <1>; + #size-cells = <1>; + model = "mv64360"; /* Default */ + compatible = "marvell,mv64360"; + clock-frequency = <133333333>; + reg = <0xf1000000 0x10000>; + virtual-reg = <0xf1000000>; + ranges = <0x88000000 0x88000000 0x1000000 /* PCI 0 I/O Space */ + 0x80000000 0x80000000 0x8000000 /* PCI 0 MEM Space */ + 0xa0000000 0xa0000000 0x4000000 /* User FLASH */ + 0x00000000 0xf1000000 0x0010000 /* Bridge's regs */ + 0xf2000000 0xf2000000 0x0040000>;/* Integrated SRAM */ + + [ child node definitions... ] + } + +2) Child nodes of /system-controller + + a) Marvell Discovery MDIO bus + + The MDIO is a bus to which the PHY devices are connected. For each + device that exists on this bus, a child node should be created. See + the definition of the PHY node below for an example of how to define + a PHY. + + Required properties: + - #address-cells : Should be <1> + - #size-cells : Should be <0> + - device_type : Should be "mdio" + - compatible : Should be "marvell,mv64360-mdio" + + Example: + + mdio { + #address-cells = <1>; + #size-cells = <0>; + device_type = "mdio"; + compatible = "marvell,mv64360-mdio"; + + ethernet-phy@0 { + ...... + }; + }; + + + b) Marvell Discovery ethernet controller + + The Discover ethernet controller is described with two levels + of nodes. The first level describes an ethernet silicon block + and the second level describes up to 3 ethernet nodes within + that block. The reason for the multiple levels is that the + registers for the node are interleaved within a single set + of registers. The "ethernet-block" level describes the + shared register set, and the "ethernet" nodes describe ethernet + port-specific properties. + + Ethernet block node + + Required properties: + - #address-cells : <1> + - #size-cells : <0> + - compatible : "marvell,mv64360-eth-block" + - reg : Offset and length of the register set for this block + + Example Discovery Ethernet block node: + ethernet-block@2000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "marvell,mv64360-eth-block"; + reg = <0x2000 0x2000>; + ethernet@0 { + ....... + }; + }; + + Ethernet port node + + Required properties: + - device_type : Should be "network". + - compatible : Should be "marvell,mv64360-eth". + - reg : Should be <0>, <1>, or <2>, according to which registers + within the silicon block the device uses. + - interrupts : <a> where a is the interrupt number for the port. + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + - phy : the phandle for the PHY connected to this ethernet + controller. + - local-mac-address : 6 bytes, MAC address + + Example Discovery Ethernet port node: + ethernet@0 { + device_type = "network"; + compatible = "marvell,mv64360-eth"; + reg = <0>; + interrupts = <32>; + interrupt-parent = <&PIC>; + phy = <&PHY0>; + local-mac-address = [ 00 00 00 00 00 00 ]; + }; + + + + c) Marvell Discovery PHY nodes + + Required properties: + - device_type : Should be "ethernet-phy" + - interrupts : <a> where a is the interrupt number for this phy. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + - reg : The ID number for the phy, usually a small integer + + Example Discovery PHY node: + ethernet-phy@1 { + device_type = "ethernet-phy"; + compatible = "broadcom,bcm5421"; + interrupts = <76>; /* GPP 12 */ + interrupt-parent = <&PIC>; + reg = <1>; + }; + + + d) Marvell Discovery SDMA nodes + + Represent DMA hardware associated with the MPSC (multiprotocol + serial controllers). + + Required properties: + - compatible : "marvell,mv64360-sdma" + - reg : Offset and length of the register set for this device + - interrupts : <a> where a is the interrupt number for the DMA + device. + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery SDMA node: + sdma@4000 { + compatible = "marvell,mv64360-sdma"; + reg = <0x4000 0xc18>; + virtual-reg = <0xf1004000>; + interrupts = <36>; + interrupt-parent = <&PIC>; + }; + + + e) Marvell Discovery BRG nodes + + Represent baud rate generator hardware associated with the MPSC + (multiprotocol serial controllers). + + Required properties: + - compatible : "marvell,mv64360-brg" + - reg : Offset and length of the register set for this device + - clock-src : A value from 0 to 15 which selects the clock + source for the baud rate generator. This value corresponds + to the CLKS value in the BRGx configuration register. See + the mv64x60 User's Manual. + - clock-frequence : The frequency (in Hz) of the baud rate + generator's input clock. + - current-speed : The current speed setting (presumably by + firmware) of the baud rate generator. + + Example Discovery BRG node: + brg@b200 { + compatible = "marvell,mv64360-brg"; + reg = <0xb200 0x8>; + clock-src = <8>; + clock-frequency = <133333333>; + current-speed = <9600>; + }; + + + f) Marvell Discovery CUNIT nodes + + Represent the Serial Communications Unit device hardware. + + Required properties: + - reg : Offset and length of the register set for this device + + Example Discovery CUNIT node: + cunit@f200 { + reg = <0xf200 0x200>; + }; + + + g) Marvell Discovery MPSCROUTING nodes + + Represent the Discovery's MPSC routing hardware + + Required properties: + - reg : Offset and length of the register set for this device + + Example Discovery CUNIT node: + mpscrouting@b500 { + reg = <0xb400 0xc>; + }; + + + h) Marvell Discovery MPSCINTR nodes + + Represent the Discovery's MPSC DMA interrupt hardware registers + (SDMA cause and mask registers). + + Required properties: + - reg : Offset and length of the register set for this device + + Example Discovery MPSCINTR node: + mpsintr@b800 { + reg = <0xb800 0x100>; + }; + + + i) Marvell Discovery MPSC nodes + + Represent the Discovery's MPSC (Multiprotocol Serial Controller) + serial port. + + Required properties: + - device_type : "serial" + - compatible : "marvell,mv64360-mpsc" + - reg : Offset and length of the register set for this device + - sdma : the phandle for the SDMA node used by this port + - brg : the phandle for the BRG node used by this port + - cunit : the phandle for the CUNIT node used by this port + - mpscrouting : the phandle for the MPSCROUTING node used by this port + - mpscintr : the phandle for the MPSCINTR node used by this port + - cell-index : the hardware index of this cell in the MPSC core + - max_idle : value needed for MPSC CHR3 (Maximum Frame Length) + register + - interrupts : <a> where a is the interrupt number for the MPSC. + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery MPSCINTR node: + mpsc@8000 { + device_type = "serial"; + compatible = "marvell,mv64360-mpsc"; + reg = <0x8000 0x38>; + virtual-reg = <0xf1008000>; + sdma = <&SDMA0>; + brg = <&BRG0>; + cunit = <&CUNIT>; + mpscrouting = <&MPSCROUTING>; + mpscintr = <&MPSCINTR>; + cell-index = <0>; + max_idle = <40>; + interrupts = <40>; + interrupt-parent = <&PIC>; + }; + + + j) Marvell Discovery Watch Dog Timer nodes + + Represent the Discovery's watchdog timer hardware + + Required properties: + - compatible : "marvell,mv64360-wdt" + - reg : Offset and length of the register set for this device + + Example Discovery Watch Dog Timer node: + wdt@b410 { + compatible = "marvell,mv64360-wdt"; + reg = <0xb410 0x8>; + }; + + + k) Marvell Discovery I2C nodes + + Represent the Discovery's I2C hardware + + Required properties: + - device_type : "i2c" + - compatible : "marvell,mv64360-i2c" + - reg : Offset and length of the register set for this device + - interrupts : <a> where a is the interrupt number for the I2C. + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery I2C node: + compatible = "marvell,mv64360-i2c"; + reg = <0xc000 0x20>; + virtual-reg = <0xf100c000>; + interrupts = <37>; + interrupt-parent = <&PIC>; + }; + + + l) Marvell Discovery PIC (Programmable Interrupt Controller) nodes + + Represent the Discovery's PIC hardware + + Required properties: + - #interrupt-cells : <1> + - #address-cells : <0> + - compatible : "marvell,mv64360-pic" + - reg : Offset and length of the register set for this device + - interrupt-controller + + Example Discovery PIC node: + pic { + #interrupt-cells = <1>; + #address-cells = <0>; + compatible = "marvell,mv64360-pic"; + reg = <0x0 0x88>; + interrupt-controller; + }; + + + m) Marvell Discovery MPP (Multipurpose Pins) multiplexing nodes + + Represent the Discovery's MPP hardware + + Required properties: + - compatible : "marvell,mv64360-mpp" + - reg : Offset and length of the register set for this device + + Example Discovery MPP node: + mpp@f000 { + compatible = "marvell,mv64360-mpp"; + reg = <0xf000 0x10>; + }; + + + n) Marvell Discovery GPP (General Purpose Pins) nodes + + Represent the Discovery's GPP hardware + + Required properties: + - compatible : "marvell,mv64360-gpp" + - reg : Offset and length of the register set for this device + + Example Discovery GPP node: + gpp@f000 { + compatible = "marvell,mv64360-gpp"; + reg = <0xf100 0x20>; + }; + + + o) Marvell Discovery PCI host bridge node + + Represents the Discovery's PCI host bridge device. The properties + for this node conform to Rev 2.1 of the PCI Bus Binding to IEEE + 1275-1994. A typical value for the compatible property is + "marvell,mv64360-pci". + + Example Discovery PCI host bridge node + pci@80000000 { + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + device_type = "pci"; + compatible = "marvell,mv64360-pci"; + reg = <0xcf8 0x8>; + ranges = <0x01000000 0x0 0x0 + 0x88000000 0x0 0x01000000 + 0x02000000 0x0 0x80000000 + 0x80000000 0x0 0x08000000>; + bus-range = <0 255>; + clock-frequency = <66000000>; + interrupt-parent = <&PIC>; + interrupt-map-mask = <0xf800 0x0 0x0 0x7>; + interrupt-map = < + /* IDSEL 0x0a */ + 0x5000 0 0 1 &PIC 80 + 0x5000 0 0 2 &PIC 81 + 0x5000 0 0 3 &PIC 91 + 0x5000 0 0 4 &PIC 93 + + /* IDSEL 0x0b */ + 0x5800 0 0 1 &PIC 91 + 0x5800 0 0 2 &PIC 93 + 0x5800 0 0 3 &PIC 80 + 0x5800 0 0 4 &PIC 81 + + /* IDSEL 0x0c */ + 0x6000 0 0 1 &PIC 91 + 0x6000 0 0 2 &PIC 93 + 0x6000 0 0 3 &PIC 80 + 0x6000 0 0 4 &PIC 81 + + /* IDSEL 0x0d */ + 0x6800 0 0 1 &PIC 93 + 0x6800 0 0 2 &PIC 80 + 0x6800 0 0 3 &PIC 81 + 0x6800 0 0 4 &PIC 91 + >; + }; + + + p) Marvell Discovery CPU Error nodes + + Represent the Discovery's CPU error handler device. + + Required properties: + - compatible : "marvell,mv64360-cpu-error" + - reg : Offset and length of the register set for this device + - interrupts : the interrupt number for this device + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery CPU Error node: + cpu-error@0070 { + compatible = "marvell,mv64360-cpu-error"; + reg = <0x70 0x10 0x128 0x28>; + interrupts = <3>; + interrupt-parent = <&PIC>; + }; + + + q) Marvell Discovery SRAM Controller nodes + + Represent the Discovery's SRAM controller device. + + Required properties: + - compatible : "marvell,mv64360-sram-ctrl" + - reg : Offset and length of the register set for this device + - interrupts : the interrupt number for this device + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery SRAM Controller node: + sram-ctrl@0380 { + compatible = "marvell,mv64360-sram-ctrl"; + reg = <0x380 0x80>; + interrupts = <13>; + interrupt-parent = <&PIC>; + }; + + + r) Marvell Discovery PCI Error Handler nodes + + Represent the Discovery's PCI error handler device. + + Required properties: + - compatible : "marvell,mv64360-pci-error" + - reg : Offset and length of the register set for this device + - interrupts : the interrupt number for this device + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery PCI Error Handler node: + pci-error@1d40 { + compatible = "marvell,mv64360-pci-error"; + reg = <0x1d40 0x40 0xc28 0x4>; + interrupts = <12>; + interrupt-parent = <&PIC>; + }; + + + s) Marvell Discovery Memory Controller nodes + + Represent the Discovery's memory controller device. + + Required properties: + - compatible : "marvell,mv64360-mem-ctrl" + - reg : Offset and length of the register set for this device + - interrupts : the interrupt number for this device + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery Memory Controller node: + mem-ctrl@1400 { + compatible = "marvell,mv64360-mem-ctrl"; + reg = <0x1400 0x60>; + interrupts = <17>; + interrupt-parent = <&PIC>; + }; + + diff --git a/Documentation/devicetree/bindings/mfd/mc13xxx.txt b/Documentation/devicetree/bindings/mfd/mc13xxx.txt new file mode 100644 index 00000000..19f6af47 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/mc13xxx.txt @@ -0,0 +1,78 @@ +* Freescale MC13783/MC13892 Power Management Integrated Circuit (PMIC) + +Required properties: +- compatible : Should be "fsl,mc13783" or "fsl,mc13892" + +Optional properties: +- fsl,mc13xxx-uses-adc : Indicate the ADC is being used +- fsl,mc13xxx-uses-codec : Indicate the Audio Codec is being used +- fsl,mc13xxx-uses-rtc : Indicate the RTC is being used +- fsl,mc13xxx-uses-touch : Indicate the touchscreen controller is being used + +Sub-nodes: +- regulators : Contain the regulator nodes. The MC13892 regulators are + bound using their names as listed below with their registers and bits + for enabling. + + vcoincell : regulator VCOINCELL (register 13, bit 23) + sw1 : regulator SW1 (register 24, bit 0) + sw2 : regulator SW2 (register 25, bit 0) + sw3 : regulator SW3 (register 26, bit 0) + sw4 : regulator SW4 (register 27, bit 0) + swbst : regulator SWBST (register 29, bit 20) + vgen1 : regulator VGEN1 (register 32, bit 0) + viohi : regulator VIOHI (register 32, bit 3) + vdig : regulator VDIG (register 32, bit 9) + vgen2 : regulator VGEN2 (register 32, bit 12) + vpll : regulator VPLL (register 32, bit 15) + vusb2 : regulator VUSB2 (register 32, bit 18) + vgen3 : regulator VGEN3 (register 33, bit 0) + vcam : regulator VCAM (register 33, bit 6) + vvideo : regulator VVIDEO (register 33, bit 12) + vaudio : regulator VAUDIO (register 33, bit 15) + vsd : regulator VSD (register 33, bit 18) + gpo1 : regulator GPO1 (register 34, bit 6) + gpo2 : regulator GPO2 (register 34, bit 8) + gpo3 : regulator GPO3 (register 34, bit 10) + gpo4 : regulator GPO4 (register 34, bit 12) + pwgt1spi : regulator PWGT1SPI (register 34, bit 15) + pwgt2spi : regulator PWGT2SPI (register 34, bit 16) + vusb : regulator VUSB (register 50, bit 3) + + The bindings details of individual regulator device can be found in: + Documentation/devicetree/bindings/regulator/regulator.txt + +Examples: + +ecspi@70010000 { /* ECSPI1 */ + fsl,spi-num-chipselects = <2>; + cs-gpios = <&gpio3 24 0>, /* GPIO4_24 */ + <&gpio3 25 0>; /* GPIO4_25 */ + status = "okay"; + + pmic: mc13892@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mc13892"; + spi-max-frequency = <6000000>; + reg = <0>; + interrupt-parent = <&gpio0>; + interrupts = <8>; + + regulators { + sw1_reg: mc13892__sw1 { + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1375000>; + regulator-boot-on; + regulator-always-on; + }; + + sw2_reg: mc13892__sw2 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1850000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/twl-familly.txt b/Documentation/devicetree/bindings/mfd/twl-familly.txt new file mode 100644 index 00000000..a66fcf94 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/twl-familly.txt @@ -0,0 +1,47 @@ +Texas Instruments TWL family + +The TWLs are Integrated Power Management Chips. +Some version might contain much more analog function like +USB transceiver or Audio amplifier. +These chips are connected to an i2c bus. + + +Required properties: +- compatible : Must be "ti,twl4030"; + For Integrated power-management/audio CODEC device used in OMAP3 + based boards +- compatible : Must be "ti,twl6030"; + For Integrated power-management used in OMAP4 based boards +- interrupts : This i2c device has an IRQ line connected to the main SoC +- interrupt-controller : Since the twl support several interrupts internally, + it is considered as an interrupt controller cascaded to the SoC one. +- #interrupt-cells = <1>; +- interrupt-parent : The parent interrupt controller. + +Optional node: +- Child nodes contain in the twl. The twl family is made of several variants + that support a different number of features. + The children nodes will thus depend of the capability of the variant. + + +Example: +/* + * Integrated Power Management Chip + * http://www.ti.com/lit/ds/symlink/twl6030.pdf + */ +twl@48 { + compatible = "ti,twl6030"; + reg = <0x48>; + interrupts = <39>; /* IRQ_SYS_1N cascaded to gic */ + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + #address-cells = <1>; + #size-cells = <0>; + + twl_rtc { + compatible = "ti,twl_rtc"; + interrupts = <11>; + reg = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt new file mode 100644 index 00000000..64bcb8be --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt @@ -0,0 +1,29 @@ +* Freescale Enhanced Secure Digital Host Controller (eSDHC) + +The Enhanced Secure Digital Host Controller provides an interface +for MMC, SD, and SDIO types of memory cards. + +Required properties: + - compatible : should be + "fsl,<chip>-esdhc", "fsl,esdhc" + - reg : should contain eSDHC registers location and length. + - interrupts : should contain eSDHC interrupt. + - interrupt-parent : interrupt source phandle. + - clock-frequency : specifies eSDHC base clock frequency. + - sdhci,wp-inverted : (optional) specifies that eSDHC controller + reports inverted write-protect state; + - sdhci,1-bit-only : (optional) specifies that a controller can + only handle 1-bit data transfers. + - sdhci,auto-cmd12: (optional) specifies that a controller can + only handle auto CMD12. + +Example: + +sdhci@2e000 { + compatible = "fsl,mpc8378-esdhc", "fsl,esdhc"; + reg = <0x2e000 0x1000>; + interrupts = <42 0x8>; + interrupt-parent = <&ipic>; + /* Filled in by U-Boot */ + clock-frequency = <0>; +}; diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt new file mode 100644 index 00000000..ab22fe6e --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt @@ -0,0 +1,34 @@ +* Freescale Enhanced Secure Digital Host Controller (eSDHC) for i.MX + +The Enhanced Secure Digital Host Controller on Freescale i.MX family +provides an interface for MMC, SD, and SDIO types of memory cards. + +Required properties: +- compatible : Should be "fsl,<chip>-esdhc" +- reg : Should contain eSDHC registers location and length +- interrupts : Should contain eSDHC interrupt + +Optional properties: +- fsl,card-wired : Indicate the card is wired to host permanently +- fsl,cd-internal : Indicate to use controller internal card detection +- fsl,wp-internal : Indicate to use controller internal write protection +- cd-gpios : Specify GPIOs for card detection +- wp-gpios : Specify GPIOs for write protection + +Examples: + +esdhc@70004000 { + compatible = "fsl,imx51-esdhc"; + reg = <0x70004000 0x4000>; + interrupts = <1>; + fsl,cd-internal; + fsl,wp-internal; +}; + +esdhc@70008000 { + compatible = "fsl,imx51-esdhc"; + reg = <0x70008000 0x4000>; + interrupts = <2>; + cd-gpios = <&gpio0 6 0>; /* GPIO1_6 */ + wp-gpios = <&gpio0 5 0>; /* GPIO1_5 */ +}; diff --git a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt new file mode 100644 index 00000000..89a0084d --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt @@ -0,0 +1,30 @@ +MMC/SD/SDIO slot directly connected to a SPI bus + +Required properties: +- compatible : should be "mmc-spi-slot". +- reg : should specify SPI address (chip-select number). +- spi-max-frequency : maximum frequency for this device (Hz). +- voltage-ranges : two cells are required, first cell specifies minimum + slot voltage (mV), second cell specifies maximum slot voltage (mV). + Several ranges could be specified. + +Optional properties: +- gpios : may specify GPIOs in this order: Card-Detect GPIO, + Write-Protect GPIO. +- interrupts : the interrupt of a card detect interrupt. +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Example: + + mmc-slot@0 { + compatible = "fsl,mpc8323rdb-mmc-slot", + "mmc-spi-slot"; + reg = <0>; + gpios = <&qe_pio_d 14 1 + &qe_pio_d 15 0>; + voltage-ranges = <3300 3300>; + spi-max-frequency = <50000000>; + interrupts = <42>; + interrupt-parent = <&PIC>; + }; diff --git a/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt b/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt new file mode 100644 index 00000000..7e511546 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt @@ -0,0 +1,27 @@ +* NVIDIA Tegra Secure Digital Host Controller + +This controller on Tegra family SoCs provides an interface for MMC, SD, +and SDIO types of memory cards. + +Required properties: +- compatible : Should be "nvidia,<chip>-sdhci" +- reg : Should contain SD/MMC registers location and length +- interrupts : Should contain SD/MMC interrupt + +Optional properties: +- cd-gpios : Specify GPIOs for card detection +- wp-gpios : Specify GPIOs for write protection +- power-gpios : Specify GPIOs for power control +- support-8bit : Boolean, indicates if 8-bit mode should be used. + +Example: + +sdhci@c8000200 { + compatible = "nvidia,tegra20-sdhci"; + reg = <0xc8000200 0x200>; + interrupts = <47>; + cd-gpios = <&gpio 69 0>; /* gpio PI5 */ + wp-gpios = <&gpio 57 0>; /* gpio PH1 */ + power-gpios = <&gpio 155 0>; /* gpio PT3 */ + support-8bit; +}; diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt new file mode 100644 index 00000000..dbd4368a --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt @@ -0,0 +1,33 @@ +* TI Highspeed MMC host controller for OMAP + +The Highspeed MMC Host Controller on TI OMAP family +provides an interface for MMC, SD, and SDIO types of memory cards. + +Required properties: +- compatible: + Should be "ti,omap2-hsmmc", for OMAP2 controllers + Should be "ti,omap3-hsmmc", for OMAP3 controllers + Should be "ti,omap4-hsmmc", for OMAP4 controllers +- ti,hwmods: Must be "mmc<n>", n is controller instance starting 1 +- reg : should contain hsmmc registers location and length + +Optional properties: +ti,dual-volt: boolean, supports dual voltage cards +<supply-name>-supply: phandle to the regulator device tree node +"supply-name" examples are "vmmc", "vmmc_aux" etc +ti,bus-width: Number of data lines, default assumed is 1 if the property is missing. +cd-gpios: GPIOs for card detection +wp-gpios: GPIOs for write protection +ti,non-removable: non-removable slot (like eMMC) +ti,needs-special-reset: Requires a special softreset sequence + +Example: + mmc1: mmc@0x4809c000 { + compatible = "ti,omap4-hsmmc"; + reg = <0x4809c000 0x400>; + ti,hwmods = "mmc1"; + ti,dual-volt; + ti,bus-width = <4>; + vmmc-supply = <&vmmc>; /* phandle to regulator node */ + ti,non-removable; + }; diff --git a/Documentation/devicetree/bindings/mtd/arm-versatile.txt b/Documentation/devicetree/bindings/mtd/arm-versatile.txt new file mode 100644 index 00000000..beace4b8 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/arm-versatile.txt @@ -0,0 +1,8 @@ +Flash device on ARM Versatile board + +Required properties: +- compatible : must be "arm,versatile-flash"; +- bank-width : width in bytes of flash interface. + +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. diff --git a/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt b/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt new file mode 100644 index 00000000..1889a4db --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt @@ -0,0 +1,17 @@ +* Atmel Data Flash + +Required properties: +- compatible : "atmel,<model>", "atmel,<series>", "atmel,dataflash". + +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. + +Example: + +flash@1 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "atmel,at45db321d", "atmel,at45", "atmel,dataflash"; + spi-max-frequency = <25000000>; + reg = <1>; +}; diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt new file mode 100644 index 00000000..a2006950 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt @@ -0,0 +1,41 @@ +Atmel NAND flash + +Required properties: +- compatible : "atmel,at91rm9200-nand". +- reg : should specify localbus address and size used for the chip, + and if availlable the ECC. +- atmel,nand-addr-offset : offset for the address latch. +- atmel,nand-cmd-offset : offset for the command latch. +- #address-cells, #size-cells : Must be present if the device has sub-nodes + representing partitions. + +- gpios : specifies the gpio pins to control the NAND device. detect is an + optional gpio and may be set to 0 if not present. + +Optional properties: +- nand-ecc-mode : String, operation mode of the NAND ecc mode, soft by default. + Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first", + "soft_bch". +- nand-bus-width : 8 or 16 bus width if not present 8 +- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false + +Examples: +nand0: nand@40000000,0 { + compatible = "atmel,at91rm9200-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x40000000 0x10000000 + 0xffffe800 0x200 + >; + atmel,nand-addr-offset = <21>; /* ale */ + atmel,nand-cmd-offset = <22>; /* cle */ + nand-on-flash-bbt; + nand-ecc-mode = "soft"; + gpios = <&pioC 13 0 /* rdy */ + &pioC 14 0 /* nce */ + 0 /* cd */ + >; + partition@0 { + ... + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt b/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt new file mode 100644 index 00000000..fce4894f --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt @@ -0,0 +1,67 @@ +Freescale Localbus UPM programmed to work with NAND flash + +Required properties: +- compatible : "fsl,upm-nand". +- reg : should specify localbus chip select and size used for the chip. +- fsl,upm-addr-offset : UPM pattern offset for the address latch. +- fsl,upm-cmd-offset : UPM pattern offset for the command latch. + +Optional properties: +- fsl,upm-wait-flags : add chip-dependent short delays after running the + UPM pattern (0x1), after writing a data byte (0x2) or after + writing out a buffer (0x4). +- fsl,upm-addr-line-cs-offsets : address offsets for multi-chip support. + The corresponding address lines are used to select the chip. +- gpios : may specify optional GPIOs connected to the Ready-Not-Busy pins + (R/B#). For multi-chip devices, "n" GPIO definitions are required + according to the number of chips. +- chip-delay : chip dependent delay for transferring data from array to + read registers (tR). Required if property "gpios" is not used + (R/B# pins not connected). + +Each flash chip described may optionally contain additional sub-nodes +describing partitions of the address space. See partition.txt for more +detail. + +Examples: + +upm@1,0 { + compatible = "fsl,upm-nand"; + reg = <1 0 1>; + fsl,upm-addr-offset = <16>; + fsl,upm-cmd-offset = <8>; + gpios = <&qe_pio_e 18 0>; + + flash { + #address-cells = <1>; + #size-cells = <1>; + compatible = "..."; + + partition@0 { + ... + }; + }; +}; + +upm@3,0 { + #address-cells = <0>; + #size-cells = <0>; + compatible = "tqc,tqm8548-upm-nand", "fsl,upm-nand"; + reg = <3 0x0 0x800>; + fsl,upm-addr-offset = <0x10>; + fsl,upm-cmd-offset = <0x08>; + /* Multi-chip NAND device */ + fsl,upm-addr-line-cs-offsets = <0x0 0x200>; + fsl,upm-wait-flags = <0x5>; + chip-delay = <25>; // in micro-seconds + + nand@0 { + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "fs"; + reg = <0x00000000 0x10000000>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt new file mode 100644 index 00000000..e2c663b3 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt @@ -0,0 +1,33 @@ +* FSMC NAND + +Required properties: +- compatible : "st,spear600-fsmc-nand" +- reg : Address range of the mtd chip +- reg-names: Should contain the reg names "fsmc_regs" and "nand_data" +- st,ale-off : Chip specific offset to ALE +- st,cle-off : Chip specific offset to CLE + +Optional properties: +- bank-width : Width (in bytes) of the device. If not present, the width + defaults to 1 byte +- nand-skip-bbtscan: Indicates the the BBT scanning should be skipped + +Example: + + fsmc: flash@d1800000 { + compatible = "st,spear600-fsmc-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0xd1800000 0x1000 /* FSMC Register */ + 0xd2000000 0x4000>; /* NAND Base */ + reg-names = "fsmc_regs", "nand_data"; + st,ale-off = <0x20000>; + st,cle-off = <0x10000>; + + bank-width = <1>; + nand-skip-bbtscan; + + partition@0 { + ... + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt b/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt new file mode 100644 index 00000000..36ef07d3 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt @@ -0,0 +1,47 @@ +GPIO assisted NAND flash + +The GPIO assisted NAND flash uses a memory mapped interface to +read/write the NAND commands and data and GPIO pins for the control +signals. + +Required properties: +- compatible : "gpio-control-nand" +- reg : should specify localbus chip select and size used for the chip. The + resource describes the data bus connected to the NAND flash and all accesses + are made in native endianness. +- #address-cells, #size-cells : Must be present if the device has sub-nodes + representing partitions. +- gpios : specifies the gpio pins to control the NAND device. nwp is an + optional gpio and may be set to 0 if not present. + +Optional properties: +- bank-width : Width (in bytes) of the device. If not present, the width + defaults to 1 byte. +- chip-delay : chip dependent delay for transferring data from array to + read registers (tR). If not present then a default of 20us is used. +- gpio-control-nand,io-sync-reg : A 64-bit physical address for a read + location used to guard against bus reordering with regards to accesses to + the GPIO's and the NAND flash data bus. If present, then after changing + GPIO state and before and after command byte writes, this register will be + read to ensure that the GPIO accesses have completed. + +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. + +Examples: + +gpio-nand@1,0 { + compatible = "gpio-control-nand"; + reg = <1 0x0000 0x2>; + #address-cells = <1>; + #size-cells = <1>; + gpios = <&banka 1 0 /* rdy */ + &banka 2 0 /* nce */ + &banka 3 0 /* ale */ + &banka 4 0 /* cle */ + 0 /* nwp */>; + + partition@0 { + ... + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt new file mode 100644 index 00000000..a63c2bd7 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt @@ -0,0 +1,71 @@ +CFI or JEDEC memory-mapped NOR flash, MTD-RAM (NVRAM...) + +Flash chips (Memory Technology Devices) are often used for solid state +file systems on embedded devices. + + - compatible : should contain the specific model of mtd chip(s) + used, if known, followed by either "cfi-flash", "jedec-flash" + or "mtd-ram". + - reg : Address range(s) of the mtd chip(s) + It's possible to (optionally) define multiple "reg" tuples so that + non-identical chips can be described in one node. + - bank-width : Width (in bytes) of the bank. Equal to the + device width times the number of interleaved chips. + - device-width : (optional) Width of a single mtd chip. If + omitted, assumed to be equal to 'bank-width'. + - #address-cells, #size-cells : Must be present if the device has + sub-nodes representing partitions (see below). In this case + both #address-cells and #size-cells must be equal to 1. + +For JEDEC compatible devices, the following additional properties +are defined: + + - vendor-id : Contains the flash chip's vendor id (1 byte). + - device-id : Contains the flash chip's device id (1 byte). + +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. + +Example: + + flash@ff000000 { + compatible = "amd,am29lv128ml", "cfi-flash"; + reg = <ff000000 01000000>; + bank-width = <4>; + device-width = <1>; + #address-cells = <1>; + #size-cells = <1>; + fs@0 { + label = "fs"; + reg = <0 f80000>; + }; + firmware@f80000 { + label ="firmware"; + reg = <f80000 80000>; + read-only; + }; + }; + +Here an example with multiple "reg" tuples: + + flash@f0000000,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "intel,PC48F4400P0VB", "cfi-flash"; + reg = <0 0x00000000 0x02000000 + 0 0x02000000 0x02000000>; + bank-width = <2>; + partition@0 { + label = "test-part1"; + reg = <0 0x04000000>; + }; + }; + +An example using SRAM: + + sram@2,0 { + compatible = "samsung,k6f1616u6a", "mtd-ram"; + reg = <2 0 0x00200000>; + bank-width = <2>; + }; + diff --git a/Documentation/devicetree/bindings/mtd/nand.txt b/Documentation/devicetree/bindings/mtd/nand.txt new file mode 100644 index 00000000..03855c8c --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/nand.txt @@ -0,0 +1,7 @@ +* MTD generic binding + +- nand-ecc-mode : String, operation mode of the NAND ecc mode. + Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first", + "soft_bch". +- nand-bus-width : 8 or 16 bus width if not present 8 +- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false diff --git a/Documentation/devicetree/bindings/mtd/partition.txt b/Documentation/devicetree/bindings/mtd/partition.txt new file mode 100644 index 00000000..f114ce16 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partition.txt @@ -0,0 +1,38 @@ +Representing flash partitions in devicetree + +Partitions can be represented by sub-nodes of an mtd device. This can be used +on platforms which have strong conventions about which portions of a flash are +used for what purposes, but which don't use an on-flash partition table such +as RedBoot. + +#address-cells & #size-cells must both be present in the mtd device and be +equal to 1. + +Required properties: +- reg : The partition's offset and size within the mtd bank. + +Optional properties: +- label : The label / name for this partition. If omitted, the label is taken + from the node name (excluding the unit address). +- read-only : This parameter, if present, is a hint to Linux that this + partition should only be mounted read-only. This is usually used for flash + partitions containing early-boot firmware images or data which should not be + clobbered. + +Examples: + + +flash@0 { + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x100000>; + read-only; + }; + + uimage@100000 { + reg = <0x0100000 0x200000>; + }; +]; diff --git a/Documentation/devicetree/bindings/mtd/spear_smi.txt b/Documentation/devicetree/bindings/mtd/spear_smi.txt new file mode 100644 index 00000000..7248aadd --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/spear_smi.txt @@ -0,0 +1,31 @@ +* SPEAr SMI + +Required properties: +- compatible : "st,spear600-smi" +- reg : Address range of the mtd chip +- #address-cells, #size-cells : Must be present if the device has sub-nodes + representing partitions. +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupts: Should contain the STMMAC interrupts +- clock-rate : Functional clock rate of SMI in Hz + +Optional properties: +- st,smi-fast-mode : Flash supports read in fast mode + +Example: + + smi: flash@fc000000 { + compatible = "st,spear600-smi"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0xfc000000 0x1000>; + interrupt-parent = <&vic1>; + interrupts = <12>; + clock-rate = <50000000>; /* 50MHz */ + + flash@f8000000 { + st,smi-fast-mode; + ... + }; + }; diff --git a/Documentation/devicetree/bindings/net/calxeda-xgmac.txt b/Documentation/devicetree/bindings/net/calxeda-xgmac.txt new file mode 100644 index 00000000..411727a3 --- /dev/null +++ b/Documentation/devicetree/bindings/net/calxeda-xgmac.txt @@ -0,0 +1,15 @@ +* Calxeda Highbank 10Gb XGMAC Ethernet + +Required properties: +- compatible : Should be "calxeda,hb-xgmac" +- reg : Address and length of the register set for the device +- interrupts : Should contain 3 xgmac interrupts. The 1st is main interrupt. + The 2nd is pwr mgt interrupt. The 3rd is low power state interrupt. + +Example: + +ethernet@fff50000 { + compatible = "calxeda,hb-xgmac"; + reg = <0xfff50000 0x1000>; + interrupts = <0 77 4 0 78 4 0 79 4>; +}; diff --git a/Documentation/devicetree/bindings/net/can/cc770.txt b/Documentation/devicetree/bindings/net/can/cc770.txt new file mode 100644 index 00000000..77027bf6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/cc770.txt @@ -0,0 +1,53 @@ +Memory mapped Bosch CC770 and Intel AN82527 CAN controller + +Note: The CC770 is a CAN controller from Bosch, which is 100% +compatible with the old AN82527 from Intel, but with "bugs" being fixed. + +Required properties: + +- compatible : should be "bosch,cc770" for the CC770 and "intc,82527" + for the AN82527. + +- reg : should specify the chip select, address offset and size required + to map the registers of the controller. The size is usually 0x80. + +- interrupts : property with a value describing the interrupt source + (number and sensitivity) required for the controller. + +Optional properties: + +- bosch,external-clock-frequency : frequency of the external oscillator + clock in Hz. Note that the internal clock frequency used by the + controller is half of that value. If not specified, a default + value of 16000000 (16 MHz) is used. + +- bosch,clock-out-frequency : slock frequency in Hz on the CLKOUT pin. + If not specified or if the specified value is 0, the CLKOUT pin + will be disabled. + +- bosch,slew-rate : slew rate of the CLKOUT signal. If not specified, + a resonable value will be calculated. + +- bosch,disconnect-rx0-input : see data sheet. + +- bosch,disconnect-rx1-input : see data sheet. + +- bosch,disconnect-tx1-output : see data sheet. + +- bosch,polarity-dominant : see data sheet. + +- bosch,divide-memory-clock : see data sheet. + +- bosch,iso-low-speed-mux : see data sheet. + +For further information, please have a look to the CC770 or AN82527. + +Examples: + +can@3,100 { + compatible = "bosch,cc770"; + reg = <3 0x100 0x80>; + interrupts = <2 0>; + interrupt-parent = <&mpic>; + bosch,external-clock-frequency = <16000000>; +}; diff --git a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt new file mode 100644 index 00000000..1ad80d58 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt @@ -0,0 +1,24 @@ +Flexcan CAN contoller on Freescale's ARM and PowerPC system-on-a-chip (SOC). + +Required properties: + +- compatible : Should be "fsl,<processor>-flexcan" + + An implementation should also claim any of the following compatibles + that it is fully backwards compatible with: + + - fsl,p1010-flexcan + +- reg : Offset and length of the register set for this device +- interrupts : Interrupt tuple for this device +- clock-frequency : The oscillator frequency driving the flexcan device + +Example: + + can@1c000 { + compatible = "fsl,p1010-flexcan"; + reg = <0x1c000 0x1000>; + interrupts = <48 0x2>; + interrupt-parent = <&mpic>; + clock-frequency = <200000000>; // filled in by bootloader + }; diff --git a/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt b/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt new file mode 100644 index 00000000..2fa4fcd3 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt @@ -0,0 +1,53 @@ +CAN Device Tree Bindings +------------------------ + +(c) 2006-2009 Secret Lab Technologies Ltd +Grant Likely <grant.likely@secretlab.ca> + +fsl,mpc5200-mscan nodes +----------------------- +In addition to the required compatible-, reg- and interrupt-properties, you can +also specify which clock source shall be used for the controller: + +- fsl,mscan-clock-source : a string describing the clock source. Valid values + are: "ip" for ip bus clock + "ref" for reference clock (XTAL) + "ref" is default in case this property is not + present. + +fsl,mpc5121-mscan nodes +----------------------- +In addition to the required compatible-, reg- and interrupt-properties, you can +also specify which clock source and divider shall be used for the controller: + +- fsl,mscan-clock-source : a string describing the clock source. Valid values + are: "ip" for ip bus clock + "ref" for reference clock + "sys" for system clock + If this property is not present, an optimal CAN + clock source and frequency based on the system + clock will be selected. If this is not possible, + the reference clock will be used. + +- fsl,mscan-clock-divider: for the reference and system clock, an additional + clock divider can be specified. By default, a + value of 1 is used. + +Note that the MPC5121 Rev. 1 processor is not supported. + +Examples: + can@1300 { + compatible = "fsl,mpc5121-mscan"; + interrupts = <12 0x8>; + interrupt-parent = <&ipic>; + reg = <0x1300 0x80>; + }; + + can@1380 { + compatible = "fsl,mpc5121-mscan"; + interrupts = <13 0x8>; + interrupt-parent = <&ipic>; + reg = <0x1380 0x80>; + fsl,mscan-clock-source = "ref"; + fsl,mscan-clock-divider = <3>; + }; diff --git a/Documentation/devicetree/bindings/net/can/sja1000.txt b/Documentation/devicetree/bindings/net/can/sja1000.txt new file mode 100644 index 00000000..c2dbcec0 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/sja1000.txt @@ -0,0 +1,53 @@ +Memory mapped SJA1000 CAN controller from NXP (formerly Philips) + +Required properties: + +- compatible : should be "nxp,sja1000". + +- reg : should specify the chip select, address offset and size required + to map the registers of the SJA1000. The size is usually 0x80. + +- interrupts: property with a value describing the interrupt source + (number and sensitivity) required for the SJA1000. + +Optional properties: + +- nxp,external-clock-frequency : Frequency of the external oscillator + clock in Hz. Note that the internal clock frequency used by the + SJA1000 is half of that value. If not specified, a default value + of 16000000 (16 MHz) is used. + +- nxp,tx-output-mode : operation mode of the TX output control logic: + <0x0> : bi-phase output mode + <0x1> : normal output mode (default) + <0x2> : test output mode + <0x3> : clock output mode + +- nxp,tx-output-config : TX output pin configuration: + <0x01> : TX0 invert + <0x02> : TX0 pull-down (default) + <0x04> : TX0 pull-up + <0x06> : TX0 push-pull + <0x08> : TX1 invert + <0x10> : TX1 pull-down + <0x20> : TX1 pull-up + <0x30> : TX1 push-pull + +- nxp,clock-out-frequency : clock frequency in Hz on the CLKOUT pin. + If not specified or if the specified value is 0, the CLKOUT pin + will be disabled. + +- nxp,no-comparator-bypass : Allows to disable the CAN input comperator. + +For further information, please have a look to the SJA1000 data sheet. + +Examples: + +can@3,100 { + compatible = "nxp,sja1000"; + reg = <3 0x100 0x80>; + interrupts = <2 0>; + interrupt-parent = <&mpic>; + nxp,external-clock-frequency = <16000000>; +}; + diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt new file mode 100644 index 00000000..de439517 --- /dev/null +++ b/Documentation/devicetree/bindings/net/fsl-fec.txt @@ -0,0 +1,24 @@ +* Freescale Fast Ethernet Controller (FEC) + +Required properties: +- compatible : Should be "fsl,<soc>-fec" +- reg : Address and length of the register set for the device +- interrupts : Should contain fec interrupt +- phy-mode : String, operation mode of the PHY interface. + Supported values are: "mii", "gmii", "sgmii", "tbi", "rmii", + "rgmii", "rgmii-id", "rgmii-rxid", "rgmii-txid", "rtbi", "smii". +- phy-reset-gpios : Should specify the gpio for phy reset + +Optional properties: +- local-mac-address : 6 bytes, mac address + +Example: + +fec@83fec000 { + compatible = "fsl,imx51-fec", "fsl,imx27-fec"; + reg = <0x83fec000 0x4000>; + interrupts = <87>; + phy-mode = "mii"; + phy-reset-gpios = <&gpio1 14 0>; /* GPIO2_14 */ + local-mac-address = [00 04 9F 01 1B B9]; +}; diff --git a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt new file mode 100644 index 00000000..2c6be037 --- /dev/null +++ b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt @@ -0,0 +1,130 @@ +* MDIO IO device + +The MDIO is a bus to which the PHY devices are connected. For each +device that exists on this bus, a child node should be created. See +the definition of the PHY node in booting-without-of.txt for an example +of how to define a PHY. + +Required properties: + - reg : Offset and length of the register set for the device + - compatible : Should define the compatible device type for the + mdio. Currently, this is most likely to be "fsl,gianfar-mdio" + +Example: + + mdio@24520 { + reg = <24520 20>; + compatible = "fsl,gianfar-mdio"; + + ethernet-phy@0 { + ...... + }; + }; + +* TBI Internal MDIO bus + +As of this writing, every tsec is associated with an internal TBI PHY. +This PHY is accessed through the local MDIO bus. These buses are defined +similarly to the mdio buses, except they are compatible with "fsl,gianfar-tbi". +The TBI PHYs underneath them are similar to normal PHYs, but the reg property +is considered instructive, rather than descriptive. The reg property should +be chosen so it doesn't interfere with other PHYs on the bus. + +* Gianfar-compatible ethernet nodes + +Properties: + + - device_type : Should be "network" + - model : Model of the device. Can be "TSEC", "eTSEC", or "FEC" + - compatible : Should be "gianfar" + - reg : Offset and length of the register set for the device + - local-mac-address : List of bytes representing the ethernet address of + this controller + - interrupts : For FEC devices, the first interrupt is the device's + interrupt. For TSEC and eTSEC devices, the first interrupt is + transmit, the second is receive, and the third is error. + - phy-handle : The phandle for the PHY connected to this ethernet + controller. + - fixed-link : <a b c d e> where a is emulated phy id - choose any, + but unique to the all specified fixed-links, b is duplex - 0 half, + 1 full, c is link speed - d#10/d#100/d#1000, d is pause - 0 no + pause, 1 pause, e is asym_pause - 0 no asym_pause, 1 asym_pause. + - phy-connection-type : a string naming the controller/PHY interface type, + i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id", "sgmii", + "tbi", or "rtbi". This property is only really needed if the connection + is of type "rgmii-id", as all other connection types are detected by + hardware. + - fsl,magic-packet : If present, indicates that the hardware supports + waking up via magic packet. + - bd-stash : If present, indicates that the hardware supports stashing + buffer descriptors in the L2. + - rx-stash-len : Denotes the number of bytes of a received buffer to stash + in the L2. + - rx-stash-idx : Denotes the index of the first byte from the received + buffer to stash in the L2. + +Example: + ethernet@24000 { + device_type = "network"; + model = "TSEC"; + compatible = "gianfar"; + reg = <0x24000 0x1000>; + local-mac-address = [ 00 E0 0C 00 73 00 ]; + interrupts = <29 2 30 2 34 2>; + interrupt-parent = <&mpic>; + phy-handle = <&phy0> + }; + +* Gianfar PTP clock nodes + +General Properties: + + - compatible Should be "fsl,etsec-ptp" + - reg Offset and length of the register set for the device + - interrupts There should be at least two interrupts. Some devices + have as many as four PTP related interrupts. + +Clock Properties: + + - fsl,tclk-period Timer reference clock period in nanoseconds. + - fsl,tmr-prsc Prescaler, divides the output clock. + - fsl,tmr-add Frequency compensation value. + - fsl,tmr-fiper1 Fixed interval period pulse generator. + - fsl,tmr-fiper2 Fixed interval period pulse generator. + - fsl,max-adj Maximum frequency adjustment in parts per billion. + + These properties set the operational parameters for the PTP + clock. You must choose these carefully for the clock to work right. + Here is how to figure good values: + + TimerOsc = system clock MHz + tclk_period = desired clock period nanoseconds + NominalFreq = 1000 / tclk_period MHz + FreqDivRatio = TimerOsc / NominalFreq (must be greater that 1.0) + tmr_add = ceil(2^32 / FreqDivRatio) + OutputClock = NominalFreq / tmr_prsc MHz + PulseWidth = 1 / OutputClock microseconds + FiperFreq1 = desired frequency in Hz + FiperDiv1 = 1000000 * OutputClock / FiperFreq1 + tmr_fiper1 = tmr_prsc * tclk_period * FiperDiv1 - tclk_period + max_adj = 1000000000 * (FreqDivRatio - 1.0) - 1 + + The calculation for tmr_fiper2 is the same as for tmr_fiper1. The + driver expects that tmr_fiper1 will be correctly set to produce a 1 + Pulse Per Second (PPS) signal, since this will be offered to the PPS + subsystem to synchronize the Linux clock. + +Example: + + ptp_clock@24E00 { + compatible = "fsl,etsec-ptp"; + reg = <0x24E00 0xB0>; + interrupts = <12 0x8 13 0x8>; + interrupt-parent = < &ipic >; + fsl,tclk-period = <10>; + fsl,tmr-prsc = <100>; + fsl,tmr-add = <0x999999A4>; + fsl,tmr-fiper1 = <0x3B9AC9F6>; + fsl,tmr-fiper2 = <0x00018696>; + fsl,max-adj = <659999998>; + }; diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt new file mode 100644 index 00000000..44afa0e5 --- /dev/null +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -0,0 +1,25 @@ +* Cadence MACB/GEM Ethernet controller + +Required properties: +- compatible: Should be "cdns,[<chip>-]{macb|gem}" + Use "cdns,at91sam9260-macb" Atmel at91sam9260 and at91sam9263 SoCs. + Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb". + Use "cnds,pc302-gem" for Picochip picoXcell pc302 and later devices based on + the Cadence GEM, or the generic form: "cdns,gem". +- reg: Address and length of the register set for the device +- interrupts: Should contain macb interrupt +- phy-mode: String, operation mode of the PHY interface. + Supported values are: "mii", "rmii", "gmii", "rgmii". + +Optional properties: +- local-mac-address: 6 bytes, mac address + +Examples: + + macb0: ethernet@fffc4000 { + compatible = "cdns,at32ap7000-macb"; + reg = <0xfffc4000 0x4000>; + interrupts = <21>; + phy-mode = "rmii"; + local-mac-address = [3a 0e 03 04 05 06]; + }; diff --git a/Documentation/devicetree/bindings/net/mdio-gpio.txt b/Documentation/devicetree/bindings/net/mdio-gpio.txt new file mode 100644 index 00000000..bc954952 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mdio-gpio.txt @@ -0,0 +1,19 @@ +MDIO on GPIOs + +Currently defined compatibles: +- virtual,gpio-mdio + +MDC and MDIO lines connected to GPIO controllers are listed in the +gpios property as described in section VIII.1 in the following order: + +MDC, MDIO. + +Example: + +mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&qe_pio_a 11 + &qe_pio_c 6>; +}; diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt new file mode 100644 index 00000000..bb8c742e --- /dev/null +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -0,0 +1,25 @@ +PHY nodes + +Required properties: + + - device_type : Should be "ethernet-phy" + - interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + - reg : The ID number for the phy, usually a small integer + - linux,phandle : phandle for this node; likely referenced by an + ethernet controller node. + +Example: + +ethernet-phy@0 { + linux,phandle = <2452000> + interrupt-parent = <40000>; + interrupts = <35 1>; + reg = <0>; + device_type = "ethernet-phy"; +}; diff --git a/Documentation/devicetree/bindings/net/smsc-lan91c111.txt b/Documentation/devicetree/bindings/net/smsc-lan91c111.txt new file mode 100644 index 00000000..953049b4 --- /dev/null +++ b/Documentation/devicetree/bindings/net/smsc-lan91c111.txt @@ -0,0 +1,10 @@ +SMSC LAN91c111 Ethernet mac + +Required properties: +- compatible = "smsc,lan91c111"; +- reg : physical address and size of registers +- interrupts : interrupt connection + +Optional properties: +- phy-device : phandle to Ethernet phy +- local-mac-address : Ethernet mac address to use diff --git a/Documentation/devicetree/bindings/net/smsc911x.txt b/Documentation/devicetree/bindings/net/smsc911x.txt new file mode 100644 index 00000000..adb5b574 --- /dev/null +++ b/Documentation/devicetree/bindings/net/smsc911x.txt @@ -0,0 +1,38 @@ +* Smart Mixed-Signal Connectivity (SMSC) LAN911x/912x Controller + +Required properties: +- compatible : Should be "smsc,lan<model>", "smsc,lan9115" +- reg : Address and length of the io space for SMSC LAN +- interrupts : Should contain SMSC LAN interrupt line +- interrupt-parent : Should be the phandle for the interrupt controller + that services interrupts for this device +- phy-mode : String, operation mode of the PHY interface. + Supported values are: "mii", "gmii", "sgmii", "tbi", "rmii", + "rgmii", "rgmii-id", "rgmii-rxid", "rgmii-txid", "rtbi", "smii". + +Optional properties: +- reg-shift : Specify the quantity to shift the register offsets by +- reg-io-width : Specify the size (in bytes) of the IO accesses that + should be performed on the device. Valid value for SMSC LAN is + 2 or 4. If it's omitted or invalid, the size would be 2. +- smsc,irq-active-high : Indicates the IRQ polarity is active-high +- smsc,irq-push-pull : Indicates the IRQ type is push-pull +- smsc,force-internal-phy : Forces SMSC LAN controller to use + internal PHY +- smsc,force-external-phy : Forces SMSC LAN controller to use + external PHY +- smsc,save-mac-address : Indicates that mac address needs to be saved + before resetting the controller +- local-mac-address : 6 bytes, mac address + +Examples: + +lan9220@f4000000 { + compatible = "smsc,lan9220", "smsc,lan9115"; + reg = <0xf4000000 0x2000000>; + phy-mode = "mii"; + interrupt-parent = <&gpio1>; + interrupts = <31>; + reg-io-width = <4>; + smsc,irq-push-pull; +}; diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt new file mode 100644 index 00000000..1f62623f --- /dev/null +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -0,0 +1,28 @@ +* STMicroelectronics 10/100/1000 Ethernet driver (GMAC) + +Required properties: +- compatible: Should be "st,spear600-gmac" +- reg: Address and length of the register set for the device +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupts: Should contain the STMMAC interrupts +- interrupt-names: Should contain the interrupt names "macirq" + "eth_wake_irq" if this interrupt is supported in the "interrupts" + property +- phy-mode: String, operation mode of the PHY interface. + Supported values are: "mii", "rmii", "gmii", "rgmii". + +Optional properties: +- mac-address: 6 bytes, mac address + +Examples: + + gmac0: ethernet@e0800000 { + compatible = "st,spear600-gmac"; + reg = <0xe0800000 0x8000>; + interrupt-parent = <&vic1>; + interrupts = <24 23>; + interrupt-names = "macirq", "eth_wake_irq"; + mac-address = [000000000000]; /* Filled in by U-Boot */ + phy-mode = "gmii"; + }; diff --git a/Documentation/devicetree/bindings/nvec/nvec_nvidia.txt b/Documentation/devicetree/bindings/nvec/nvec_nvidia.txt new file mode 100644 index 00000000..5aeee53f --- /dev/null +++ b/Documentation/devicetree/bindings/nvec/nvec_nvidia.txt @@ -0,0 +1,9 @@ +NVIDIA compliant embedded controller + +Required properties: +- compatible : should be "nvidia,nvec". +- reg : the iomem of the i2c slave controller +- interrupts : the interrupt line of the i2c slave controller +- clock-frequency : the frequency of the i2c bus +- gpios : the gpio used for ec request +- slave-addr: the i2c address of the slave controller diff --git a/Documentation/devicetree/bindings/open-pic.txt b/Documentation/devicetree/bindings/open-pic.txt new file mode 100644 index 00000000..909a902d --- /dev/null +++ b/Documentation/devicetree/bindings/open-pic.txt @@ -0,0 +1,98 @@ +* Open PIC Binding + +This binding specifies what properties must be available in the device tree +representation of an Open PIC compliant interrupt controller. This binding is +based on the binding defined for Open PIC in [1] and is a superset of that +binding. + +Required properties: + + NOTE: Many of these descriptions were paraphrased here from [1] to aid + readability. + + - compatible: Specifies the compatibility list for the PIC. The type + shall be <string> and the value shall include "open-pic". + + - reg: Specifies the base physical address(s) and size(s) of this + PIC's addressable register space. The type shall be <prop-encoded-array>. + + - interrupt-controller: The presence of this property identifies the node + as an Open PIC. No property value shall be defined. + + - #interrupt-cells: Specifies the number of cells needed to encode an + interrupt source. The type shall be a <u32> and the value shall be 2. + + - #address-cells: Specifies the number of cells needed to encode an + address. The type shall be <u32> and the value shall be 0. As such, + 'interrupt-map' nodes do not have to specify a parent unit address. + +Optional properties: + + - pic-no-reset: The presence of this property indicates that the PIC + shall not be reset during runtime initialization. No property value shall + be defined. The presence of this property also mandates that any + initialization related to interrupt sources shall be limited to sources + explicitly referenced in the device tree. + +* Interrupt Specifier Definition + + Interrupt specifiers consists of 2 cells encoded as + follows: + + - <1st-cell>: The interrupt-number that identifies the interrupt source. + + - <2nd-cell>: The level-sense information, encoded as follows: + 0 = low-to-high edge triggered + 1 = active low level-sensitive + 2 = active high level-sensitive + 3 = high-to-low edge triggered + +* Examples + +Example 1: + + /* + * An Open PIC interrupt controller + */ + mpic: pic@40000 { + // This is an interrupt controller node. + interrupt-controller; + + // No address cells so that 'interrupt-map' nodes which reference + // this Open PIC node do not need a parent address specifier. + #address-cells = <0>; + + // Two cells to encode interrupt sources. + #interrupt-cells = <2>; + + // Offset address of 0x40000 and size of 0x40000. + reg = <0x40000 0x40000>; + + // Compatible with Open PIC. + compatible = "open-pic"; + + // The PIC shall not be reset. + pic-no-reset; + }; + +Example 2: + + /* + * An interrupt generating device that is wired to an Open PIC. + */ + serial0: serial@4500 { + // Interrupt source '42' that is active high level-sensitive. + // Note that there are only two cells as specified in the interrupt + // parent's '#interrupt-cells' property. + interrupts = <42 2>; + + // The interrupt controller that this device is wired to. + interrupt-parent = <&mpic>; + }; + +* References + +[1] Power.org (TM) Standard for Embedded Power Architecture (TM) Platform + Requirements (ePAPR), Version 1.0, July 2008. + (http://www.power.org/resources/downloads/Power_ePAPR_APPROVED_v1.0.pdf) + diff --git a/Documentation/devicetree/bindings/pci/83xx-512x-pci.txt b/Documentation/devicetree/bindings/pci/83xx-512x-pci.txt new file mode 100644 index 00000000..35a46536 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/83xx-512x-pci.txt @@ -0,0 +1,40 @@ +* Freescale 83xx and 512x PCI bridges + +Freescale 83xx and 512x SOCs include the same pci bridge core. + +83xx/512x specific notes: +- reg: should contain two address length tuples + The first is for the internal pci bridge registers + The second is for the pci config space access registers + +Example (MPC8313ERDB) + pci0: pci@e0008500 { + cell-index = <1>; + interrupt-map-mask = <0xf800 0x0 0x0 0x7>; + interrupt-map = < + /* IDSEL 0x0E -mini PCI */ + 0x7000 0x0 0x0 0x1 &ipic 18 0x8 + 0x7000 0x0 0x0 0x2 &ipic 18 0x8 + 0x7000 0x0 0x0 0x3 &ipic 18 0x8 + 0x7000 0x0 0x0 0x4 &ipic 18 0x8 + + /* IDSEL 0x0F - PCI slot */ + 0x7800 0x0 0x0 0x1 &ipic 17 0x8 + 0x7800 0x0 0x0 0x2 &ipic 18 0x8 + 0x7800 0x0 0x0 0x3 &ipic 17 0x8 + 0x7800 0x0 0x0 0x4 &ipic 18 0x8>; + interrupt-parent = <&ipic>; + interrupts = <66 0x8>; + bus-range = <0x0 0x0>; + ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000 + 0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000 + 0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>; + clock-frequency = <66666666>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0xe0008500 0x100 /* internal registers */ + 0xe0008300 0x8>; /* config space access registers */ + compatible = "fsl,mpc8349-pci"; + device_type = "pci"; + }; diff --git a/Documentation/devicetree/bindings/pinmux/pinmux_nvidia.txt b/Documentation/devicetree/bindings/pinmux/pinmux_nvidia.txt new file mode 100644 index 00000000..36f82dbd --- /dev/null +++ b/Documentation/devicetree/bindings/pinmux/pinmux_nvidia.txt @@ -0,0 +1,5 @@ +NVIDIA Tegra 2 pinmux controller + +Required properties: +- compatible : "nvidia,tegra20-pinmux" + diff --git a/Documentation/devicetree/bindings/power_supply/max17042_battery.txt b/Documentation/devicetree/bindings/power_supply/max17042_battery.txt new file mode 100644 index 00000000..5bc9b685 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/max17042_battery.txt @@ -0,0 +1,18 @@ +max17042_battery +~~~~~~~~~~~~~~~~ + +Required properties : + - compatible : "maxim,max17042" + +Optional properties : + - maxim,rsns-microohm : Resistance of rsns resistor in micro Ohms + (datasheet-recommended value is 10000). + Defining this property enables current-sense functionality. + +Example: + + battery-charger@36 { + compatible = "maxim,max17042"; + reg = <0x36>; + maxim,rsns-microohm = <10000>; + }; diff --git a/Documentation/devicetree/bindings/power_supply/olpc_battery.txt b/Documentation/devicetree/bindings/power_supply/olpc_battery.txt new file mode 100644 index 00000000..c8901b39 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/olpc_battery.txt @@ -0,0 +1,5 @@ +OLPC battery +~~~~~~~~~~~~ + +Required properties: + - compatible : "olpc,xo1-battery" diff --git a/Documentation/devicetree/bindings/power_supply/sbs_sbs-battery.txt b/Documentation/devicetree/bindings/power_supply/sbs_sbs-battery.txt new file mode 100644 index 00000000..c40e8926 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/sbs_sbs-battery.txt @@ -0,0 +1,23 @@ +SBS sbs-battery +~~~~~~~~~~ + +Required properties : + - compatible : "sbs,sbs-battery" + +Optional properties : + - sbs,i2c-retry-count : The number of times to retry i2c transactions on i2c + IO failure. + - sbs,poll-retry-count : The number of times to try looking for new status + after an external change notification. + - sbs,battery-detect-gpios : The gpio which signals battery detection and + a flag specifying its polarity. + +Example: + + bq20z75@b { + compatible = "sbs,sbs-battery"; + reg = < 0xb >; + sbs,i2c-retry-count = <2>; + sbs,poll-retry-count = <10>; + sbs,battery-detect-gpios = <&gpio-controller 122 1>; + } diff --git a/Documentation/devicetree/bindings/powerpc/4xx/cpm.txt b/Documentation/devicetree/bindings/powerpc/4xx/cpm.txt new file mode 100644 index 00000000..ee459806 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/4xx/cpm.txt @@ -0,0 +1,52 @@ +PPC4xx Clock Power Management (CPM) node + +Required properties: + - compatible : compatible list, currently only "ibm,cpm" + - dcr-access-method : "native" + - dcr-reg : < DCR register range > + +Optional properties: + - er-offset : All 4xx SoCs with a CPM controller have + one of two different order for the CPM + registers. Some have the CPM registers + in the following order (ER,FR,SR). The + others have them in the following order + (SR,ER,FR). For the second case set + er-offset = <1>. + - unused-units : specifier consist of one cell. For each + bit in the cell, the corresponding bit + in CPM will be set to turn off unused + devices. + - idle-doze : specifier consist of one cell. For each + bit in the cell, the corresponding bit + in CPM will be set to turn off unused + devices. This is usually just CPM[CPU]. + - standby : specifier consist of one cell. For each + bit in the cell, the corresponding bit + in CPM will be set on standby and + restored on resume. + - suspend : specifier consist of one cell. For each + bit in the cell, the corresponding bit + in CPM will be set on suspend (mem) and + restored on resume. Note, for standby + and suspend the corresponding bits can + be different or the same. Usually for + standby only class 2 and 3 units are set. + However, the interface does not care. + If they are the same, the additional + power saving will be seeing if support + is available to put the DDR in self + refresh mode and any additional power + saving techniques for the specific SoC. + +Example: + CPM0: cpm { + compatible = "ibm,cpm"; + dcr-access-method = "native"; + dcr-reg = <0x160 0x003>; + er-offset = <0>; + unused-units = <0x00000100>; + idle-doze = <0x02000000>; + standby = <0xfeff0000>; + suspend = <0xfeff791d>; +}; diff --git a/Documentation/devicetree/bindings/powerpc/4xx/emac.txt b/Documentation/devicetree/bindings/powerpc/4xx/emac.txt new file mode 100644 index 00000000..2161334a --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/4xx/emac.txt @@ -0,0 +1,148 @@ + 4xx/Axon EMAC ethernet nodes + + The EMAC ethernet controller in IBM and AMCC 4xx chips, and also + the Axon bridge. To operate this needs to interact with a ths + special McMAL DMA controller, and sometimes an RGMII or ZMII + interface. In addition to the nodes and properties described + below, the node for the OPB bus on which the EMAC sits must have a + correct clock-frequency property. + + i) The EMAC node itself + + Required properties: + - device_type : "network" + + - compatible : compatible list, contains 2 entries, first is + "ibm,emac-CHIP" where CHIP is the host ASIC (440gx, + 405gp, Axon) and second is either "ibm,emac" or + "ibm,emac4". For Axon, thus, we have: "ibm,emac-axon", + "ibm,emac4" + - interrupts : <interrupt mapping for EMAC IRQ and WOL IRQ> + - interrupt-parent : optional, if needed for interrupt mapping + - reg : <registers mapping> + - local-mac-address : 6 bytes, MAC address + - mal-device : phandle of the associated McMAL node + - mal-tx-channel : 1 cell, index of the tx channel on McMAL associated + with this EMAC + - mal-rx-channel : 1 cell, index of the rx channel on McMAL associated + with this EMAC + - cell-index : 1 cell, hardware index of the EMAC cell on a given + ASIC (typically 0x0 and 0x1 for EMAC0 and EMAC1 on + each Axon chip) + - max-frame-size : 1 cell, maximum frame size supported in bytes + - rx-fifo-size : 1 cell, Rx fifo size in bytes for 10 and 100 Mb/sec + operations. + For Axon, 2048 + - tx-fifo-size : 1 cell, Tx fifo size in bytes for 10 and 100 Mb/sec + operations. + For Axon, 2048. + - fifo-entry-size : 1 cell, size of a fifo entry (used to calculate + thresholds). + For Axon, 0x00000010 + - mal-burst-size : 1 cell, MAL burst size (used to calculate thresholds) + in bytes. + For Axon, 0x00000100 (I think ...) + - phy-mode : string, mode of operations of the PHY interface. + Supported values are: "mii", "rmii", "smii", "rgmii", + "tbi", "gmii", rtbi", "sgmii". + For Axon on CAB, it is "rgmii" + - mdio-device : 1 cell, required iff using shared MDIO registers + (440EP). phandle of the EMAC to use to drive the + MDIO lines for the PHY used by this EMAC. + - zmii-device : 1 cell, required iff connected to a ZMII. phandle of + the ZMII device node + - zmii-channel : 1 cell, required iff connected to a ZMII. Which ZMII + channel or 0xffffffff if ZMII is only used for MDIO. + - rgmii-device : 1 cell, required iff connected to an RGMII. phandle + of the RGMII device node. + For Axon: phandle of plb5/plb4/opb/rgmii + - rgmii-channel : 1 cell, required iff connected to an RGMII. Which + RGMII channel is used by this EMAC. + Fox Axon: present, whatever value is appropriate for each + EMAC, that is the content of the current (bogus) "phy-port" + property. + + Optional properties: + - phy-address : 1 cell, optional, MDIO address of the PHY. If absent, + a search is performed. + - phy-map : 1 cell, optional, bitmap of addresses to probe the PHY + for, used if phy-address is absent. bit 0x00000001 is + MDIO address 0. + For Axon it can be absent, though my current driver + doesn't handle phy-address yet so for now, keep + 0x00ffffff in it. + - rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec + operations (if absent the value is the same as + rx-fifo-size). For Axon, either absent or 2048. + - tx-fifo-size-gige : 1 cell, Tx fifo size in bytes for 1000 Mb/sec + operations (if absent the value is the same as + tx-fifo-size). For Axon, either absent or 2048. + - tah-device : 1 cell, optional. If connected to a TAH engine for + offload, phandle of the TAH device node. + - tah-channel : 1 cell, optional. If appropriate, channel used on the + TAH engine. + + Example: + + EMAC0: ethernet@40000800 { + device_type = "network"; + compatible = "ibm,emac-440gp", "ibm,emac"; + interrupt-parent = <&UIC1>; + interrupts = <1c 4 1d 4>; + reg = <40000800 70>; + local-mac-address = [00 04 AC E3 1B 1E]; + mal-device = <&MAL0>; + mal-tx-channel = <0 1>; + mal-rx-channel = <0>; + cell-index = <0>; + max-frame-size = <5dc>; + rx-fifo-size = <1000>; + tx-fifo-size = <800>; + phy-mode = "rmii"; + phy-map = <00000001>; + zmii-device = <&ZMII0>; + zmii-channel = <0>; + }; + + ii) McMAL node + + Required properties: + - device_type : "dma-controller" + - compatible : compatible list, containing 2 entries, first is + "ibm,mcmal-CHIP" where CHIP is the host ASIC (like + emac) and the second is either "ibm,mcmal" or + "ibm,mcmal2". + For Axon, "ibm,mcmal-axon","ibm,mcmal2" + - interrupts : <interrupt mapping for the MAL interrupts sources: + 5 sources: tx_eob, rx_eob, serr, txde, rxde>. + For Axon: This is _different_ from the current + firmware. We use the "delayed" interrupts for txeob + and rxeob. Thus we end up with mapping those 5 MPIC + interrupts, all level positive sensitive: 10, 11, 32, + 33, 34 (in decimal) + - dcr-reg : < DCR registers range > + - dcr-parent : if needed for dcr-reg + - num-tx-chans : 1 cell, number of Tx channels + - num-rx-chans : 1 cell, number of Rx channels + + iii) ZMII node + + Required properties: + - compatible : compatible list, containing 2 entries, first is + "ibm,zmii-CHIP" where CHIP is the host ASIC (like + EMAC) and the second is "ibm,zmii". + For Axon, there is no ZMII node. + - reg : <registers mapping> + + iv) RGMII node + + Required properties: + - compatible : compatible list, containing 2 entries, first is + "ibm,rgmii-CHIP" where CHIP is the host ASIC (like + EMAC) and the second is "ibm,rgmii". + For Axon, "ibm,rgmii-axon","ibm,rgmii" + - reg : <registers mapping> + - revision : as provided by the RGMII new version register if + available. + For Axon: 0x0000012a + diff --git a/Documentation/devicetree/bindings/powerpc/4xx/ndfc.txt b/Documentation/devicetree/bindings/powerpc/4xx/ndfc.txt new file mode 100644 index 00000000..869f0b5f --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/4xx/ndfc.txt @@ -0,0 +1,39 @@ +AMCC NDFC (NanD Flash Controller) + +Required properties: +- compatible : "ibm,ndfc". +- reg : should specify chip select and size used for the chip (0x2000). + +Optional properties: +- ccr : NDFC config and control register value (default 0). +- bank-settings : NDFC bank configuration register value (default 0). + +Notes: +- partition(s) - follows the OF MTD standard for partitions + +Example: + +ndfc@1,0 { + compatible = "ibm,ndfc"; + reg = <0x00000001 0x00000000 0x00002000>; + ccr = <0x00001000>; + bank-settings = <0x80002222>; + #address-cells = <1>; + #size-cells = <1>; + + nand { + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "kernel"; + reg = <0x00000000 0x00200000>; + }; + partition@200000 { + label = "root"; + reg = <0x00200000 0x03E00000>; + }; + }; +}; + + diff --git a/Documentation/devicetree/bindings/powerpc/4xx/ppc440spe-adma.txt b/Documentation/devicetree/bindings/powerpc/4xx/ppc440spe-adma.txt new file mode 100644 index 00000000..515ebcf1 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/4xx/ppc440spe-adma.txt @@ -0,0 +1,93 @@ +PPC440SPe DMA/XOR (DMA Controller and XOR Accelerator) + +Device nodes needed for operation of the ppc440spe-adma driver +are specified hereby. These are I2O/DMA, DMA and XOR nodes +for DMA engines and Memory Queue Module node. The latter is used +by ADMA driver for configuration of RAID-6 H/W capabilities of +the PPC440SPe. In addition to the nodes and properties described +below, the ranges property of PLB node must specify ranges for +DMA devices. + + i) The I2O node + + Required properties: + + - compatible : "ibm,i2o-440spe"; + - reg : <registers mapping> + - dcr-reg : <DCR registers range> + + Example: + + I2O: i2o@400100000 { + compatible = "ibm,i2o-440spe"; + reg = <0x00000004 0x00100000 0x100>; + dcr-reg = <0x060 0x020>; + }; + + + ii) The DMA node + + Required properties: + + - compatible : "ibm,dma-440spe"; + - cell-index : 1 cell, hardware index of the DMA engine + (typically 0x0 and 0x1 for DMA0 and DMA1) + - reg : <registers mapping> + - dcr-reg : <DCR registers range> + - interrupts : <interrupt mapping for DMA0/1 interrupts sources: + 2 sources: DMAx CS FIFO Needs Service IRQ (on UIC0) + and DMA Error IRQ (on UIC1). The latter is common + for both DMA engines>. + - interrupt-parent : needed for interrupt mapping + + Example: + + DMA0: dma0@400100100 { + compatible = "ibm,dma-440spe"; + cell-index = <0>; + reg = <0x00000004 0x00100100 0x100>; + dcr-reg = <0x060 0x020>; + interrupt-parent = <&DMA0>; + interrupts = <0 1>; + #interrupt-cells = <1>; + #address-cells = <0>; + #size-cells = <0>; + interrupt-map = < + 0 &UIC0 0x14 4 + 1 &UIC1 0x16 4>; + }; + + + iii) XOR Accelerator node + + Required properties: + + - compatible : "amcc,xor-accelerator"; + - reg : <registers mapping> + - interrupts : <interrupt mapping for XOR interrupt source> + - interrupt-parent : for interrupt mapping + + Example: + + xor-accel@400200000 { + compatible = "amcc,xor-accelerator"; + reg = <0x00000004 0x00200000 0x400>; + interrupt-parent = <&UIC1>; + interrupts = <0x1f 4>; + }; + + + iv) Memory Queue Module node + + Required properties: + + - compatible : "ibm,mq-440spe"; + - dcr-reg : <DCR registers range> + + Example: + + MQ0: mq { + compatible = "ibm,mq-440spe"; + dcr-reg = <0x040 0x020>; + }; + diff --git a/Documentation/devicetree/bindings/powerpc/4xx/reboot.txt b/Documentation/devicetree/bindings/powerpc/4xx/reboot.txt new file mode 100644 index 00000000..d7217260 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/4xx/reboot.txt @@ -0,0 +1,18 @@ +Reboot property to control system reboot on PPC4xx systems: + +By setting "reset_type" to one of the following values, the default +software reset mechanism may be overidden. Here the possible values of +"reset_type": + + 1 - PPC4xx core reset + 2 - PPC4xx chip reset + 3 - PPC4xx system reset (default) + +Example: + + cpu@0 { + device_type = "cpu"; + model = "PowerPC,440SPe"; + ... + reset-type = <2>; /* Use chip-reset */ + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/board.txt b/Documentation/devicetree/bindings/powerpc/fsl/board.txt new file mode 100644 index 00000000..380914e9 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/board.txt @@ -0,0 +1,69 @@ +Freescale Reference Board Bindings + +This document describes device tree bindings for various devices that +exist on some Freescale reference boards. + +* Board Control and Status (BCSR) + +Required properties: + + - compatible : Should be "fsl,<board>-bcsr" + - reg : Offset and length of the register set for the device + +Example: + + bcsr@f8000000 { + compatible = "fsl,mpc8360mds-bcsr"; + reg = <f8000000 8000>; + }; + +* Freescale on-board FPGA + +This is the memory-mapped registers for on board FPGA. + +Required properities: +- compatible: should be a board-specific string followed by a string + indicating the type of FPGA. Example: + "fsl,<board>-fpga", "fsl,fpga-pixis" +- reg: should contain the address and the length of the FPGA register set. +- interrupt-parent: should specify phandle for the interrupt controller. +- interrupts: should specify event (wakeup) IRQ. + +Example (P1022DS): + + board-control@3,0 { + compatible = "fsl,p1022ds-fpga", "fsl,fpga-ngpixis"; + reg = <3 0 0x30>; + interrupt-parent = <&mpic>; + interrupts = <8 8 0 0>; + }; + +* Freescale BCSR GPIO banks + +Some BCSR registers act as simple GPIO controllers, each such +register can be represented by the gpio-controller node. + +Required properities: +- compatible : Should be "fsl,<board>-bcsr-gpio". +- reg : Should contain the address and the length of the GPIO bank + register. +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). +- gpio-controller : Marks the port as GPIO controller. + +Example: + + bcsr@1,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8360mds-bcsr"; + reg = <1 0 0x8000>; + ranges = <0 1 0 0x8000>; + + bcsr13: gpio-controller@d { + #gpio-cells = <2>; + compatible = "fsl,mpc8360mds-bcsr-gpio"; + reg = <0xd 1>; + gpio-controller; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cache_sram.txt b/Documentation/devicetree/bindings/powerpc/fsl/cache_sram.txt new file mode 100644 index 00000000..781955f5 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cache_sram.txt @@ -0,0 +1,20 @@ +* Freescale PQ3 and QorIQ based Cache SRAM + +Freescale's mpc85xx and some QorIQ platforms provide an +option of configuring a part of (or full) cache memory +as SRAM. This cache SRAM representation in the device +tree should be done as under:- + +Required properties: + +- compatible : should be "fsl,p2020-cache-sram" +- fsl,cache-sram-ctlr-handle : points to the L2 controller +- reg : offset and length of the cache-sram. + +Example: + +cache-sram@fff00000 { + fsl,cache-sram-ctlr-handle = <&L2>; + reg = <0 0xfff00000 0 0x10000>; + compatible = "fsl,p2020-cache-sram"; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm.txt new file mode 100644 index 00000000..160c7524 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm.txt @@ -0,0 +1,67 @@ +* Freescale Communications Processor Module + +NOTE: This is an interim binding, and will likely change slightly, +as more devices are supported. The QE bindings especially are +incomplete. + +* Root CPM node + +Properties: +- compatible : "fsl,cpm1", "fsl,cpm2", or "fsl,qe". +- reg : A 48-byte region beginning with CPCR. + +Example: + cpm@119c0 { + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + compatible = "fsl,mpc8272-cpm", "fsl,cpm2"; + reg = <119c0 30>; + } + +* Properties common to multiple CPM/QE devices + +- fsl,cpm-command : This value is ORed with the opcode and command flag + to specify the device on which a CPM command operates. + +- fsl,cpm-brg : Indicates which baud rate generator the device + is associated with. If absent, an unused BRG + should be dynamically allocated. If zero, the + device uses an external clock rather than a BRG. + +- reg : Unless otherwise specified, the first resource represents the + scc/fcc/ucc registers, and the second represents the device's + parameter RAM region (if it has one). + +* Multi-User RAM (MURAM) + +The multi-user/dual-ported RAM is expressed as a bus under the CPM node. + +Ranges must be set up subject to the following restrictions: + +- Children's reg nodes must be offsets from the start of all muram, even + if the user-data area does not begin at zero. +- If multiple range entries are used, the difference between the parent + address and the child address must be the same in all, so that a single + mapping can cover them all while maintaining the ability to determine + CPM-side offsets with pointer subtraction. It is recommended that + multiple range entries not be used. +- A child address of zero must be translatable, even if no reg resources + contain it. + +A child "data" node must exist, compatible with "fsl,cpm-muram-data", to +indicate the portion of muram that is usable by the OS for arbitrary +purposes. The data node may have an arbitrary number of reg resources, +all of which contribute to the allocatable muram pool. + +Example, based on mpc8272: + muram@0 { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 10000>; + + data@0 { + compatible = "fsl,cpm-muram-data"; + reg = <0 2000 9800 800>; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/brg.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/brg.txt new file mode 100644 index 00000000..4c7d45ea --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/brg.txt @@ -0,0 +1,21 @@ +* Baud Rate Generators + +Currently defined compatibles: +fsl,cpm-brg +fsl,cpm1-brg +fsl,cpm2-brg + +Properties: +- reg : There may be an arbitrary number of reg resources; BRG + numbers are assigned to these in order. +- clock-frequency : Specifies the base frequency driving + the BRG. + +Example: + brg@119f0 { + compatible = "fsl,mpc8272-brg", + "fsl,cpm2-brg", + "fsl,cpm-brg"; + reg = <119f0 10 115f0 10>; + clock-frequency = <d#25000000>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/i2c.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/i2c.txt new file mode 100644 index 00000000..87bc6048 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/i2c.txt @@ -0,0 +1,41 @@ +* I2C + +The I2C controller is expressed as a bus under the CPM node. + +Properties: +- compatible : "fsl,cpm1-i2c", "fsl,cpm2-i2c" +- reg : On CPM2 devices, the second resource doesn't specify the I2C + Parameter RAM itself, but the I2C_BASE field of the CPM2 Parameter RAM + (typically 0x8afc 0x2). +- #address-cells : Should be one. The cell is the i2c device address with + the r/w bit set to zero. +- #size-cells : Should be zero. +- clock-frequency : Can be used to set the i2c clock frequency. If + unspecified, a default frequency of 60kHz is being used. +The following two properties are deprecated. They are only used by legacy +i2c drivers to find the bus to probe: +- linux,i2c-index : Can be used to hard code an i2c bus number. By default, + the bus number is dynamically assigned by the i2c core. +- linux,i2c-class : Can be used to override the i2c class. The class is used + by legacy i2c device drivers to find a bus in a specific context like + system management, video or sound. By default, I2C_CLASS_HWMON (1) is + being used. The definition of the classes can be found in + include/i2c/i2c.h + +Example, based on mpc823: + + i2c@860 { + compatible = "fsl,mpc823-i2c", + "fsl,cpm1-i2c"; + reg = <0x860 0x20 0x3c80 0x30>; + interrupts = <16>; + interrupt-parent = <&CPM_PIC>; + fsl,cpm-command = <0x10>; + #address-cells = <1>; + #size-cells = <0>; + + rtc@68 { + compatible = "dallas,ds1307"; + reg = <0x68>; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/pic.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/pic.txt new file mode 100644 index 00000000..8e3ee168 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/pic.txt @@ -0,0 +1,18 @@ +* Interrupt Controllers + +Currently defined compatibles: +- fsl,cpm1-pic + - only one interrupt cell +- fsl,pq1-pic +- fsl,cpm2-pic + - second interrupt cell is level/sense: + - 2 is falling edge + - 8 is active low + +Example: + interrupt-controller@10c00 { + #interrupt-cells = <2>; + interrupt-controller; + reg = <10c00 80>; + compatible = "mpc8272-pic", "fsl,cpm2-pic"; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/usb.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/usb.txt new file mode 100644 index 00000000..74bfda4b --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/usb.txt @@ -0,0 +1,15 @@ +* USB (Universal Serial Bus Controller) + +Properties: +- compatible : "fsl,cpm1-usb", "fsl,cpm2-usb", "fsl,qe-usb" + +Example: + usb@11bc0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,cpm2-usb"; + reg = <11b60 18 8b00 100>; + interrupts = <b 8>; + interrupt-parent = <&PIC>; + fsl,cpm-command = <2e600000>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/gpio.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/gpio.txt new file mode 100644 index 00000000..349f79fd --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/gpio.txt @@ -0,0 +1,38 @@ +Every GPIO controller node must have #gpio-cells property defined, +this information will be used to translate gpio-specifiers. + +On CPM1 devices, all ports are using slightly different register layouts. +Ports A, C and D are 16bit ports and Ports B and E are 32bit ports. + +On CPM2 devices, all ports are 32bit ports and use a common register layout. + +Required properties: +- compatible : "fsl,cpm1-pario-bank-a", "fsl,cpm1-pario-bank-b", + "fsl,cpm1-pario-bank-c", "fsl,cpm1-pario-bank-d", + "fsl,cpm1-pario-bank-e", "fsl,cpm2-pario-bank" +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). +- gpio-controller : Marks the port as GPIO controller. + +Example of three SOC GPIO banks defined as gpio-controller nodes: + + CPM1_PIO_A: gpio-controller@950 { + #gpio-cells = <2>; + compatible = "fsl,cpm1-pario-bank-a"; + reg = <0x950 0x10>; + gpio-controller; + }; + + CPM1_PIO_B: gpio-controller@ab8 { + #gpio-cells = <2>; + compatible = "fsl,cpm1-pario-bank-b"; + reg = <0xab8 0x10>; + gpio-controller; + }; + + CPM1_PIO_E: gpio-controller@ac8 { + #gpio-cells = <2>; + compatible = "fsl,cpm1-pario-bank-e"; + reg = <0xac8 0x18>; + gpio-controller; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/network.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/network.txt new file mode 100644 index 00000000..0e426944 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/network.txt @@ -0,0 +1,45 @@ +* Network + +Currently defined compatibles: +- fsl,cpm1-scc-enet +- fsl,cpm2-scc-enet +- fsl,cpm1-fec-enet +- fsl,cpm2-fcc-enet (third resource is GFEMR) +- fsl,qe-enet + +Example: + + ethernet@11300 { + device_type = "network"; + compatible = "fsl,mpc8272-fcc-enet", + "fsl,cpm2-fcc-enet"; + reg = <11300 20 8400 100 11390 1>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <20 8>; + interrupt-parent = <&PIC>; + phy-handle = <&PHY0>; + fsl,cpm-command = <12000300>; + }; + +* MDIO + +Currently defined compatibles: +fsl,pq1-fec-mdio (reg is same as first resource of FEC device) +fsl,cpm2-mdio-bitbang (reg is port C registers) + +Properties for fsl,cpm2-mdio-bitbang: +fsl,mdio-pin : pin of port C controlling mdio data +fsl,mdc-pin : pin of port C controlling mdio clock + +Example: + mdio@10d40 { + device_type = "mdio"; + compatible = "fsl,mpc8272ads-mdio-bitbang", + "fsl,mpc8272-mdio-bitbang", + "fsl,cpm2-mdio-bitbang"; + reg = <10d40 14>; + #address-cells = <1>; + #size-cells = <0>; + fsl,mdio-pin = <12>; + fsl,mdc-pin = <13>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe.txt new file mode 100644 index 00000000..4f893026 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe.txt @@ -0,0 +1,115 @@ +* Freescale QUICC Engine module (QE) +This represents qe module that is installed on PowerQUICC II Pro. + +NOTE: This is an interim binding; it should be updated to fit +in with the CPM binding later in this document. + +Basically, it is a bus of devices, that could act more or less +as a complete entity (UCC, USB etc ). All of them should be siblings on +the "root" qe node, using the common properties from there. +The description below applies to the qe of MPC8360 and +more nodes and properties would be extended in the future. + +i) Root QE device + +Required properties: +- compatible : should be "fsl,qe"; +- model : precise model of the QE, Can be "QE", "CPM", or "CPM2" +- reg : offset and length of the device registers. +- bus-frequency : the clock frequency for QUICC Engine. +- fsl,qe-num-riscs: define how many RISC engines the QE has. +- fsl,qe-num-snums: define how many serial number(SNUM) the QE can use for the + threads. + +Optional properties: +- fsl,firmware-phandle: + Usage: required only if there is no fsl,qe-firmware child node + Value type: <phandle> + Definition: Points to a firmware node (see "QE Firmware Node" below) + that contains the firmware that should be uploaded for this QE. + The compatible property for the firmware node should say, + "fsl,qe-firmware". + +Recommended properties +- brg-frequency : the internal clock source frequency for baud-rate + generators in Hz. + +Example: + qe@e0100000 { + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + compatible = "fsl,qe"; + ranges = <0 e0100000 00100000>; + reg = <e0100000 480>; + brg-frequency = <0>; + bus-frequency = <179A7B00>; + } + +* Multi-User RAM (MURAM) + +Required properties: +- compatible : should be "fsl,qe-muram", "fsl,cpm-muram". +- mode : the could be "host" or "slave". +- ranges : Should be defined as specified in 1) to describe the + translation of MURAM addresses. +- data-only : sub-node which defines the address area under MURAM + bus that can be allocated as data/parameter + +Example: + + muram@10000 { + compatible = "fsl,qe-muram", "fsl,cpm-muram"; + ranges = <0 00010000 0000c000>; + + data-only@0{ + compatible = "fsl,qe-muram-data", + "fsl,cpm-muram-data"; + reg = <0 c000>; + }; + }; + +* QE Firmware Node + +This node defines a firmware binary that is embedded in the device tree, for +the purpose of passing the firmware from bootloader to the kernel, or from +the hypervisor to the guest. + +The firmware node itself contains the firmware binary contents, a compatible +property, and any firmware-specific properties. The node should be placed +inside a QE node that needs it. Doing so eliminates the need for a +fsl,firmware-phandle property. Other QE nodes that need the same firmware +should define an fsl,firmware-phandle property that points to the firmware node +in the first QE node. + +The fsl,firmware property can be specified in the DTS (possibly using incbin) +or can be inserted by the boot loader at boot time. + +Required properties: + - compatible + Usage: required + Value type: <string> + Definition: A standard property. Specify a string that indicates what + kind of firmware it is. For QE, this should be "fsl,qe-firmware". + + - fsl,firmware + Usage: required + Value type: <prop-encoded-array>, encoded as an array of bytes + Definition: A standard property. This property contains the firmware + binary "blob". + +Example: + qe1@e0080000 { + compatible = "fsl,qe"; + qe_firmware:qe-firmware { + compatible = "fsl,qe-firmware"; + fsl,firmware = [0x70 0xcd 0x00 0x00 0x01 0x46 0x45 ...]; + }; + ... + }; + + qe2@e0090000 { + compatible = "fsl,qe"; + fsl,firmware-phandle = <&qe_firmware>; + ... + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/firmware.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/firmware.txt new file mode 100644 index 00000000..249db3a1 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/firmware.txt @@ -0,0 +1,24 @@ +* Uploaded QE firmware + + If a new firmware has been uploaded to the QE (usually by the + boot loader), then a 'firmware' child node should be added to the QE + node. This node provides information on the uploaded firmware that + device drivers may need. + + Required properties: + - id: The string name of the firmware. This is taken from the 'id' + member of the qe_firmware structure of the uploaded firmware. + Device drivers can search this string to determine if the + firmware they want is already present. + - extended-modes: The Extended Modes bitfield, taken from the + firmware binary. It is a 64-bit number represented + as an array of two 32-bit numbers. + - virtual-traps: The virtual traps, taken from the firmware binary. + It is an array of 8 32-bit numbers. + +Example: + firmware { + id = "Soft-UART"; + extended-modes = <0 0>; + virtual-traps = <0 0 0 0 0 0 0 0>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/par_io.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/par_io.txt new file mode 100644 index 00000000..60984260 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/par_io.txt @@ -0,0 +1,51 @@ +* Parallel I/O Ports + +This node configures Parallel I/O ports for CPUs with QE support. +The node should reside in the "soc" node of the tree. For each +device that using parallel I/O ports, a child node should be created. +See the definition of the Pin configuration nodes below for more +information. + +Required properties: +- device_type : should be "par_io". +- reg : offset to the register set and its length. +- num-ports : number of Parallel I/O ports + +Example: +par_io@1400 { + reg = <1400 100>; + #address-cells = <1>; + #size-cells = <0>; + device_type = "par_io"; + num-ports = <7>; + ucc_pin@01 { + ...... + }; + +Note that "par_io" nodes are obsolete, and should not be used for +the new device trees. Instead, each Par I/O bank should be represented +via its own gpio-controller node: + +Required properties: +- #gpio-cells : should be "2". +- compatible : should be "fsl,<chip>-qe-pario-bank", + "fsl,mpc8323-qe-pario-bank". +- reg : offset to the register set and its length. +- gpio-controller : node to identify gpio controllers. + +Example: + qe_pio_a: gpio-controller@1400 { + #gpio-cells = <2>; + compatible = "fsl,mpc8360-qe-pario-bank", + "fsl,mpc8323-qe-pario-bank"; + reg = <0x1400 0x18>; + gpio-controller; + }; + + qe_pio_e: gpio-controller@1460 { + #gpio-cells = <2>; + compatible = "fsl,mpc8360-qe-pario-bank", + "fsl,mpc8323-qe-pario-bank"; + reg = <0x1460 0x18>; + gpio-controller; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/pincfg.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/pincfg.txt new file mode 100644 index 00000000..c5b43061 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/pincfg.txt @@ -0,0 +1,60 @@ +* Pin configuration nodes + +Required properties: +- linux,phandle : phandle of this node; likely referenced by a QE + device. +- pio-map : array of pin configurations. Each pin is defined by 6 + integers. The six numbers are respectively: port, pin, dir, + open_drain, assignment, has_irq. + - port : port number of the pin; 0-6 represent port A-G in UM. + - pin : pin number in the port. + - dir : direction of the pin, should encode as follows: + + 0 = The pin is disabled + 1 = The pin is an output + 2 = The pin is an input + 3 = The pin is I/O + + - open_drain : indicates the pin is normal or wired-OR: + + 0 = The pin is actively driven as an output + 1 = The pin is an open-drain driver. As an output, the pin is + driven active-low, otherwise it is three-stated. + + - assignment : function number of the pin according to the Pin Assignment + tables in User Manual. Each pin can have up to 4 possible functions in + QE and two options for CPM. + - has_irq : indicates if the pin is used as source of external + interrupts. + +Example: + ucc_pin@01 { + linux,phandle = <140001>; + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 0 3 1 0 1 0 /* TxD0 */ + 0 4 1 0 1 0 /* TxD1 */ + 0 5 1 0 1 0 /* TxD2 */ + 0 6 1 0 1 0 /* TxD3 */ + 1 6 1 0 3 0 /* TxD4 */ + 1 7 1 0 1 0 /* TxD5 */ + 1 9 1 0 2 0 /* TxD6 */ + 1 a 1 0 2 0 /* TxD7 */ + 0 9 2 0 1 0 /* RxD0 */ + 0 a 2 0 1 0 /* RxD1 */ + 0 b 2 0 1 0 /* RxD2 */ + 0 c 2 0 1 0 /* RxD3 */ + 0 d 2 0 1 0 /* RxD4 */ + 1 1 2 0 2 0 /* RxD5 */ + 1 0 2 0 2 0 /* RxD6 */ + 1 4 2 0 2 0 /* RxD7 */ + 0 7 1 0 1 0 /* TX_EN */ + 0 8 1 0 1 0 /* TX_ER */ + 0 f 2 0 1 0 /* RX_DV */ + 0 10 2 0 1 0 /* RX_ER */ + 0 0 2 0 1 0 /* RX_CLK */ + 2 9 1 0 3 0 /* GTX_CLK - CLK10 */ + 2 8 2 0 1 0>; /* GTX125 - CLK9 */ + }; + + diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt new file mode 100644 index 00000000..e47734be --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt @@ -0,0 +1,70 @@ +* UCC (Unified Communications Controllers) + +Required properties: +- device_type : should be "network", "hldc", "uart", "transparent" + "bisync", "atm", or "serial". +- compatible : could be "ucc_geth" or "fsl_atm" and so on. +- cell-index : the ucc number(1-8), corresponding to UCCx in UM. +- reg : Offset and length of the register set for the device +- interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. +- pio-handle : The phandle for the Parallel I/O port configuration. +- port-number : for UART drivers, the port number to use, between 0 and 3. + This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0. + The port number is added to the minor number of the device. Unlike the + CPM UART driver, the port-number is required for the QE UART driver. +- soft-uart : for UART drivers, if specified this means the QE UART device + driver should use "Soft-UART" mode, which is needed on some SOCs that have + broken UART hardware. Soft-UART is provided via a microcode upload. +- rx-clock-name: the UCC receive clock source + "none": clock source is disabled + "brg1" through "brg16": clock source is BRG1-BRG16, respectively + "clk1" through "clk24": clock source is CLK1-CLK24, respectively +- tx-clock-name: the UCC transmit clock source + "none": clock source is disabled + "brg1" through "brg16": clock source is BRG1-BRG16, respectively + "clk1" through "clk24": clock source is CLK1-CLK24, respectively +The following two properties are deprecated. rx-clock has been replaced +with rx-clock-name, and tx-clock has been replaced with tx-clock-name. +Drivers that currently use the deprecated properties should continue to +do so, in order to support older device trees, but they should be updated +to check for the new properties first. +- rx-clock : represents the UCC receive clock source. + 0x00 : clock source is disabled; + 0x1~0x10 : clock source is BRG1~BRG16 respectively; + 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively. +- tx-clock: represents the UCC transmit clock source; + 0x00 : clock source is disabled; + 0x1~0x10 : clock source is BRG1~BRG16 respectively; + 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively. + +Required properties for network device_type: +- mac-address : list of bytes representing the ethernet address. +- phy-handle : The phandle for the PHY connected to this controller. + +Recommended properties: +- phy-connection-type : a string naming the controller/PHY interface type, + i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal + Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only), + "tbi", or "rtbi". + +Example: + ucc@2000 { + device_type = "network"; + compatible = "ucc_geth"; + cell-index = <1>; + reg = <2000 200>; + interrupts = <a0 0>; + interrupt-parent = <700>; + mac-address = [ 00 04 9f 00 23 23 ]; + rx-clock = "none"; + tx-clock = "clk9"; + phy-handle = <212000>; + phy-connection-type = "gmii"; + pio-handle = <140001>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/usb.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/usb.txt new file mode 100644 index 00000000..9ccd5f30 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/usb.txt @@ -0,0 +1,37 @@ +Freescale QUICC Engine USB Controller + +Required properties: +- compatible : should be "fsl,<chip>-qe-usb", "fsl,mpc8323-qe-usb". +- reg : the first two cells should contain usb registers location and + length, the next two two cells should contain PRAM location and + length. +- interrupts : should contain USB interrupt. +- interrupt-parent : interrupt source phandle. +- fsl,fullspeed-clock : specifies the full speed USB clock source: + "none": clock source is disabled + "brg1" through "brg16": clock source is BRG1-BRG16, respectively + "clk1" through "clk24": clock source is CLK1-CLK24, respectively +- fsl,lowspeed-clock : specifies the low speed USB clock source: + "none": clock source is disabled + "brg1" through "brg16": clock source is BRG1-BRG16, respectively + "clk1" through "clk24": clock source is CLK1-CLK24, respectively +- hub-power-budget : USB power budget for the root hub, in mA. +- gpios : should specify GPIOs in this order: USBOE, USBTP, USBTN, USBRP, + USBRN, SPEED (optional), and POWER (optional). + +Example: + +usb@6c0 { + compatible = "fsl,mpc8360-qe-usb", "fsl,mpc8323-qe-usb"; + reg = <0x6c0 0x40 0x8b00 0x100>; + interrupts = <11>; + interrupt-parent = <&qeic>; + fsl,fullspeed-clock = "clk21"; + gpios = <&qe_pio_b 2 0 /* USBOE */ + &qe_pio_b 3 0 /* USBTP */ + &qe_pio_b 8 0 /* USBTN */ + &qe_pio_b 9 0 /* USBRP */ + &qe_pio_b 11 0 /* USBRN */ + &qe_pio_e 20 0 /* SPEED */ + &qe_pio_e 21 0 /* POWER */>; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/serial.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/serial.txt new file mode 100644 index 00000000..2ea76d9d --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/serial.txt @@ -0,0 +1,32 @@ +* Serial + +Currently defined compatibles: +- fsl,cpm1-smc-uart +- fsl,cpm2-smc-uart +- fsl,cpm1-scc-uart +- fsl,cpm2-scc-uart +- fsl,qe-uart + +Modem control lines connected to GPIO controllers are listed in the gpios +property as described in booting-without-of.txt, section IX.1 in the following +order: + +CTS, RTS, DCD, DSR, DTR, and RI. + +The gpios property is optional and can be left out when control lines are +not used. + +Example: + + serial@11a00 { + device_type = "serial"; + compatible = "fsl,mpc8272-scc-uart", + "fsl,cpm2-scc-uart"; + reg = <11a00 20 8000 100>; + interrupts = <28 8>; + interrupt-parent = <&PIC>; + fsl,cpm-brg = <1>; + fsl,cpm-command = <00800000>; + gpios = <&gpio_c 15 0 + &gpio_d 29 0>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/dcsr.txt b/Documentation/devicetree/bindings/powerpc/fsl/dcsr.txt new file mode 100644 index 00000000..9d54eb5a --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/dcsr.txt @@ -0,0 +1,395 @@ +=================================================================== +Debug Control and Status Register (DCSR) Binding +Copyright 2011 Freescale Semiconductor Inc. + +NOTE: The bindings described in this document are preliminary and subject +to change. Some of the compatible strings that contain only generic names +may turn out to be inappropriate, or need additional properties to describe +the integration of the block with the rest of the chip. + +===================================================================== +Debug Control and Status Register Memory Map + +Description + +This node defines the base address and range for the +defined DCSR Memory Map. Child nodes will describe the individual +debug blocks defined within this memory space. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,dcsr" and "simple-bus". + The DCSR space exists in the memory-mapped bus. + + - #address-cells + Usage: required + Value type: <u32> + Definition: A standard property. Defines the number of cells + or representing physical addresses in child nodes. + + - #size-cells + Usage: required + Value type: <u32> + Definition: A standard property. Defines the number of cells + or representing the size of physical addresses in + child nodes. + + - ranges + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + range of the DCSR space. + +EXAMPLE + dcsr: dcsr@f00000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,dcsr", "simple-bus"; + ranges = <0x00000000 0xf 0x00000000 0x01008000>; + }; + +===================================================================== +Event Processing Unit + +This node represents the region of DCSR space allocated to the EPU + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,dcsr-epu" + + - interrupts + Usage: required + Value type: <prop_encoded-array> + Definition: Specifies the interrupts generated by the EPU. + The value of the interrupts property consists of three + interrupt specifiers. The format of the specifier is defined + by the binding document describing the node's interrupt parent. + + The EPU counters can be configured to assert the performance + monitor interrupt signal based on either counter overflow or value + match. Which counter asserted the interrupt is captured in an EPU + Counter Interrupt Status Register (EPCPUISR). + + The EPU unit can also be configured to assert either or both of + two interrupt signals based on debug event sources within the SoC. + The interrupt signals are epu_xt_int0 and epu_xt_int1. + Which event source asserted the interrupt is captured in an EPU + Interrupt Status Register (EPISR0,EPISR1). + + Interrupt numbers are lised in order (perfmon, event0, event1). + + - interrupt-parent + Usage: required + Value type: <phandle> + Definition: A single <phandle> value that points + to the interrupt parent to which the child domain + is being mapped. Value must be "&mpic" + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-epu@0 { + compatible = "fsl,dcsr-epu"; + interrupts = <52 2 0 0 + 84 2 0 0 + 85 2 0 0>; + interrupt-parent = <&mpic>; + reg = <0x0 0x1000>; + }; + +======================================================================= +Nexus Port Controller + +This node represents the region of DCSR space allocated to the NPC + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,dcsr-npc" + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + The Nexus Port controller occupies two regions in the DCSR space + with distinct functionality. + + The first register range describes the Nexus Port Controller + control and status registers. + + The second register range describes the Nexus Port Controller + internal trace buffer. The NPC trace buffer is a small memory buffer + which stages the nexus trace data for transmission via the Aurora port + or to a DDR based trace buffer. In some configurations the NPC trace + buffer can be the only trace buffer used. + + +EXAMPLE + dcsr-npc { + compatible = "fsl,dcsr-npc"; + reg = <0x1000 0x1000 0x1000000 0x8000>; + }; + +======================================================================= +Nexus Concentrator + +This node represents the region of DCSR space allocated to the NXC + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,dcsr-nxc" + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-nxc@2000 { + compatible = "fsl,dcsr-nxc"; + reg = <0x2000 0x1000>; + }; +======================================================================= +CoreNet Debug Controller + +This node represents the region of DCSR space allocated to +the CoreNet Debug controller. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,dcsr-corenet" + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + The CoreNet Debug controller occupies two regions in the DCSR space + with distinct functionality. + + The first register range describes the CoreNet Debug Controller + functionalty to perform transaction and transaction attribute matches. + + The second register range describes the CoreNet Debug Controller + functionalty to trigger event notifications and debug traces. + +EXAMPLE + dcsr-corenet { + compatible = "fsl,dcsr-corenet"; + reg = <0x8000 0x1000 0xB0000 0x1000>; + }; + +======================================================================= +Data Path Debug controller + +This node represents the region of DCSR space allocated to +the DPAA Debug Controller. This controller controls debug configuration +for the QMAN and FMAN blocks. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include both an identifier specific to the SoC + or Debug IP of the form "fsl,<soc>-dcsr-dpaa" in addition to the + generic compatible string "fsl,dcsr-dpaa". + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-dpaa@9000 { + compatible = "fsl,p4080-dcsr-dpaa", "fsl,dcsr-dpaa"; + reg = <0x9000 0x1000>; + }; + +======================================================================= +OCeaN Debug controller + +This node represents the region of DCSR space allocated to +the OCN Debug Controller. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include both an identifier specific to the SoC + or Debug IP of the form "fsl,<soc>-dcsr-ocn" in addition to the + generic compatible string "fsl,dcsr-ocn". + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-ocn@11000 { + compatible = "fsl,p4080-dcsr-ocn", "fsl,dcsr-ocn"; + reg = <0x11000 0x1000>; + }; + +======================================================================= +DDR Controller Debug controller + +This node represents the region of DCSR space allocated to +the OCN Debug Controller. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,dcsr-ddr" + + - dev-handle + Usage: required + Definition: A phandle to associate this debug node with its + component controller. + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-ddr@12000 { + compatible = "fsl,dcsr-ddr"; + dev-handle = <&ddr1>; + reg = <0x12000 0x1000>; + }; + +======================================================================= +Nexus Aurora Link Controller + +This node represents the region of DCSR space allocated to +the NAL Controller. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include both an identifier specific to the SoC + or Debug IP of the form "fsl,<soc>-dcsr-nal" in addition to the + generic compatible string "fsl,dcsr-nal". + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-nal@18000 { + compatible = "fsl,p4080-dcsr-nal", "fsl,dcsr-nal"; + reg = <0x18000 0x1000>; + }; + + +======================================================================= +Run Control and Power Management + +This node represents the region of DCSR space allocated to +the RCPM Debug Controller. This functionlity is limited to the +control the debug operations of the SoC and cores. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include both an identifier specific to the SoC + or Debug IP of the form "fsl,<soc>-dcsr-rcpm" in addition to the + generic compatible string "fsl,dcsr-rcpm". + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-rcpm@22000 { + compatible = "fsl,p4080-dcsr-rcpm", "fsl,dcsr-rcpm"; + reg = <0x22000 0x1000>; + }; + +======================================================================= +Core Service Bridge Proxy + +This node represents the region of DCSR space allocated to +the Core Service Bridge Proxies. +There is one Core Service Bridge Proxy device for each CPU in the system. +This functionlity provides access to the debug operations of the CPU. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include both an identifier specific to the cpu + of the form "fsl,dcsr-<cpu>-sb-proxy" in addition to the + generic compatible string "fsl,dcsr-cpu-sb-proxy". + + - cpu-handle + Usage: required + Definition: A phandle to associate this debug node with its cpu. + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-cpu-sb-proxy@40000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", + "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu0>; + reg = <0x40000 0x1000>; + }; + dcsr-cpu-sb-proxy@41000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", + "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu1>; + reg = <0x41000 0x1000>; + }; + +======================================================================= diff --git a/Documentation/devicetree/bindings/powerpc/fsl/diu.txt b/Documentation/devicetree/bindings/powerpc/fsl/diu.txt new file mode 100644 index 00000000..b66cb6d3 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/diu.txt @@ -0,0 +1,34 @@ +* Freescale Display Interface Unit + +The Freescale DIU is a LCD controller, with proper hardware, it can also +drive DVI monitors. + +Required properties: +- compatible : should be "fsl,diu" or "fsl,mpc5121-diu". +- reg : should contain at least address and length of the DIU register + set. +- interrupts : one DIU interrupt should be described here. +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Optional properties: +- edid : verbatim EDID data block describing attached display. + Data from the detailed timing descriptor will be used to + program the display controller. + +Example (MPC8610HPCD): + display@2c000 { + compatible = "fsl,diu"; + reg = <0x2c000 100>; + interrupts = <72 2>; + interrupt-parent = <&mpic>; + }; + +Example for MPC5121: + display@2100 { + compatible = "fsl,mpc5121-diu"; + reg = <0x2100 0x100>; + interrupts = <64 0x8>; + interrupt-parent = <&ipic>; + edid = [edid-data]; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/dma.txt b/Documentation/devicetree/bindings/powerpc/fsl/dma.txt new file mode 100644 index 00000000..2a4b4bce --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/dma.txt @@ -0,0 +1,144 @@ +* Freescale 83xx DMA Controller + +Freescale PowerPC 83xx have on chip general purpose DMA controllers. + +Required properties: + +- compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-dma", where CHIP is the processor + (mpc8349, mpc8360, etc.) and the second is + "fsl,elo-dma" +- reg : <registers mapping for DMA general status reg> +- ranges : Should be defined as specified in 1) to describe the + DMA controller channels. +- cell-index : controller index. 0 for controller @ 0x8100 +- interrupts : <interrupt mapping for DMA IRQ> +- interrupt-parent : optional, if needed for interrupt mapping + + +- DMA channel nodes: + - compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-dma-channel", where CHIP is the processor + (mpc8349, mpc8350, etc.) and the second is + "fsl,elo-dma-channel". However, see note below. + - reg : <registers mapping for channel> + - cell-index : dma channel index starts at 0. + +Optional properties: + - interrupts : <interrupt mapping for DMA channel IRQ> + (on 83xx this is expected to be identical to + the interrupts property of the parent node) + - interrupt-parent : optional, if needed for interrupt mapping + +Example: + dma@82a8 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8349-dma", "fsl,elo-dma"; + reg = <0x82a8 4>; + ranges = <0 0x8100 0x1a4>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + cell-index = <0>; + dma-channel@0 { + compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; + cell-index = <0>; + reg = <0 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + dma-channel@80 { + compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; + cell-index = <1>; + reg = <0x80 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + dma-channel@100 { + compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; + cell-index = <2>; + reg = <0x100 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + dma-channel@180 { + compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; + cell-index = <3>; + reg = <0x180 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + }; + +* Freescale 85xx/86xx DMA Controller + +Freescale PowerPC 85xx/86xx have on chip general purpose DMA controllers. + +Required properties: + +- compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-dma", where CHIP is the processor + (mpc8540, mpc8540, etc.) and the second is + "fsl,eloplus-dma" +- reg : <registers mapping for DMA general status reg> +- cell-index : controller index. 0 for controller @ 0x21000, + 1 for controller @ 0xc000 +- ranges : Should be defined as specified in 1) to describe the + DMA controller channels. + +- DMA channel nodes: + - compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-dma-channel", where CHIP is the processor + (mpc8540, mpc8560, etc.) and the second is + "fsl,eloplus-dma-channel". However, see note below. + - cell-index : dma channel index starts at 0. + - reg : <registers mapping for channel> + - interrupts : <interrupt mapping for DMA channel IRQ> + - interrupt-parent : optional, if needed for interrupt mapping + +Example: + dma@21300 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8540-dma", "fsl,eloplus-dma"; + reg = <0x21300 4>; + ranges = <0 0x21100 0x200>; + cell-index = <0>; + dma-channel@0 { + compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; + reg = <0 0x80>; + cell-index = <0>; + interrupt-parent = <&mpic>; + interrupts = <20 2>; + }; + dma-channel@80 { + compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; + reg = <0x80 0x80>; + cell-index = <1>; + interrupt-parent = <&mpic>; + interrupts = <21 2>; + }; + dma-channel@100 { + compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; + reg = <0x100 0x80>; + cell-index = <2>; + interrupt-parent = <&mpic>; + interrupts = <22 2>; + }; + dma-channel@180 { + compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; + reg = <0x180 0x80>; + cell-index = <3>; + interrupt-parent = <&mpic>; + interrupts = <23 2>; + }; + }; + +Note on DMA channel compatible properties: The compatible property must say +"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel" to be used by the Elo DMA +driver (fsldma). Any DMA channel used by fsldma cannot be used by another +DMA driver, such as the SSI sound drivers for the MPC8610. Therefore, any DMA +channel that should be used for another driver should not use +"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel". For the SSI drivers, for +example, the compatible property should be "fsl,ssi-dma-channel". See ssi.txt +for more information. diff --git a/Documentation/devicetree/bindings/powerpc/fsl/ecm.txt b/Documentation/devicetree/bindings/powerpc/fsl/ecm.txt new file mode 100644 index 00000000..f514f29c --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/ecm.txt @@ -0,0 +1,64 @@ +===================================================================== +E500 LAW & Coherency Module Device Tree Binding +Copyright (C) 2009 Freescale Semiconductor Inc. +===================================================================== + +Local Access Window (LAW) Node + +The LAW node represents the region of CCSR space where local access +windows are configured. For ECM based devices this is the first 4k +of CCSR space that includes CCSRBAR, ALTCBAR, ALTCAR, BPTR, and some +number of local access windows as specified by fsl,num-laws. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,ecm-law" + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. The value specifies the + physical address offset and length of the CCSR space + registers. + + - fsl,num-laws + Usage: required + Value type: <u32> + Definition: The value specifies the number of local access + windows for this device. + +===================================================================== + +E500 Coherency Module Node + +The E500 LAW node represents the region of CCSR space where ECM config +and error reporting registers exist, this is the second 4k (0x1000) +of CCSR space. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,CHIP-ecm", "fsl,ecm" where + CHIP is the processor (mpc8572, mpc8544, etc.) + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. The value specifies the + physical address offset and length of the CCSR space + registers. + + - interrupts + Usage: required + Value type: <prop-encoded-array> + + - interrupt-parent + Usage: required + Value type: <phandle> + +===================================================================== diff --git a/Documentation/devicetree/bindings/powerpc/fsl/gtm.txt b/Documentation/devicetree/bindings/powerpc/fsl/gtm.txt new file mode 100644 index 00000000..9a33efde --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/gtm.txt @@ -0,0 +1,31 @@ +* Freescale General-purpose Timers Module + +Required properties: + - compatible : should be + "fsl,<chip>-gtm", "fsl,gtm" for SOC GTMs + "fsl,<chip>-qe-gtm", "fsl,qe-gtm", "fsl,gtm" for QE GTMs + "fsl,<chip>-cpm2-gtm", "fsl,cpm2-gtm", "fsl,gtm" for CPM2 GTMs + - reg : should contain gtm registers location and length (0x40). + - interrupts : should contain four interrupts. + - interrupt-parent : interrupt source phandle. + - clock-frequency : specifies the frequency driving the timer. + +Example: + +timer@500 { + compatible = "fsl,mpc8360-gtm", "fsl,gtm"; + reg = <0x500 0x40>; + interrupts = <90 8 78 8 84 8 72 8>; + interrupt-parent = <&ipic>; + /* filled by u-boot */ + clock-frequency = <0>; +}; + +timer@440 { + compatible = "fsl,mpc8360-qe-gtm", "fsl,qe-gtm", "fsl,gtm"; + reg = <0x440 0x40>; + interrupts = <12 13 14 15>; + interrupt-parent = <&qeic>; + /* filled by u-boot */ + clock-frequency = <0>; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/guts.txt b/Documentation/devicetree/bindings/powerpc/fsl/guts.txt new file mode 100644 index 00000000..9e7a2417 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/guts.txt @@ -0,0 +1,25 @@ +* Global Utilities Block + +The global utilities block controls power management, I/O device +enabling, power-on-reset configuration monitoring, general-purpose +I/O signal configuration, alternate function selection for multiplexed +signals, and clock control. + +Required properties: + + - compatible : Should define the compatible device type for + global-utilities. + - reg : Offset and length of the register set for the device. + +Recommended properties: + + - fsl,has-rstcr : Indicates that the global utilities register set + contains a functioning "reset control register" (i.e. the board + is wired to reset upon setting the HRESET_REQ bit in this register). + +Example: + global-utilities@e0000 { /* global utilities block */ + compatible = "fsl,mpc8548-guts"; + reg = <e0000 1000>; + fsl,has-rstcr; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/ifc.txt b/Documentation/devicetree/bindings/powerpc/fsl/ifc.txt new file mode 100644 index 00000000..939a26d5 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/ifc.txt @@ -0,0 +1,76 @@ +Integrated Flash Controller + +Properties: +- name : Should be ifc +- compatible : should contain "fsl,ifc". The version of the integrated + flash controller can be found in the IFC_REV register at + offset zero. + +- #address-cells : Should be either two or three. The first cell is the + chipselect number, and the remaining cells are the + offset into the chipselect. +- #size-cells : Either one or two, depending on how large each chipselect + can be. +- reg : Offset and length of the register set for the device +- interrupts : IFC has two interrupts. The first one is the "common" + interrupt(CM_EVTER_STAT), and second is the NAND interrupt + (NAND_EVTER_STAT). + +- ranges : Each range corresponds to a single chipselect, and covers + the entire access window as configured. + +Child device nodes describe the devices connected to IFC such as NOR (e.g. +cfi-flash) and NAND (fsl,ifc-nand). There might be board specific devices +like FPGAs, CPLDs, etc. + +Example: + + ifc@ffe1e000 { + compatible = "fsl,ifc", "simple-bus"; + #address-cells = <2>; + #size-cells = <1>; + reg = <0x0 0xffe1e000 0 0x2000>; + interrupts = <16 2 19 2>; + + /* NOR, NAND Flashes and CPLD on board */ + ranges = <0x0 0x0 0x0 0xee000000 0x02000000 + 0x1 0x0 0x0 0xffa00000 0x00010000 + 0x3 0x0 0x0 0xffb00000 0x00020000>; + + flash@0,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "cfi-flash"; + reg = <0x0 0x0 0x2000000>; + bank-width = <2>; + device-width = <1>; + + partition@0 { + /* 32MB for user data */ + reg = <0x0 0x02000000>; + label = "NOR Data"; + }; + }; + + flash@1,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,ifc-nand"; + reg = <0x1 0x0 0x10000>; + + partition@0 { + /* This location must not be altered */ + /* 1MB for u-boot Bootloader Image */ + reg = <0x0 0x00100000>; + label = "NAND U-Boot Image"; + read-only; + }; + }; + + cpld@3,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,p1010rdb-cpld"; + reg = <0x3 0x0 0x000001f>; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/lbc.txt b/Documentation/devicetree/bindings/powerpc/fsl/lbc.txt new file mode 100644 index 00000000..3300fec5 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/lbc.txt @@ -0,0 +1,35 @@ +* Chipselect/Local Bus + +Properties: +- name : Should be localbus +- #address-cells : Should be either two or three. The first cell is the + chipselect number, and the remaining cells are the + offset into the chipselect. +- #size-cells : Either one or two, depending on how large each chipselect + can be. +- ranges : Each range corresponds to a single chipselect, and cover + the entire access window as configured. + +Example: + localbus@f0010100 { + compatible = "fsl,mpc8272-localbus", + "fsl,pq2-localbus"; + #address-cells = <2>; + #size-cells = <1>; + reg = <f0010100 40>; + + ranges = <0 0 fe000000 02000000 + 1 0 f4500000 00008000>; + + flash@0,0 { + compatible = "jedec-flash"; + reg = <0 0 2000000>; + bank-width = <4>; + device-width = <1>; + }; + + board-control@1,0 { + reg = <1 0 20>; + compatible = "fsl,mpc8272ads-bcsr"; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mcm.txt b/Documentation/devicetree/bindings/powerpc/fsl/mcm.txt new file mode 100644 index 00000000..4ceda9b3 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mcm.txt @@ -0,0 +1,64 @@ +===================================================================== +MPX LAW & Coherency Module Device Tree Binding +Copyright (C) 2009 Freescale Semiconductor Inc. +===================================================================== + +Local Access Window (LAW) Node + +The LAW node represents the region of CCSR space where local access +windows are configured. For MCM based devices this is the first 4k +of CCSR space that includes CCSRBAR, ALTCBAR, ALTCAR, BPTR, and some +number of local access windows as specified by fsl,num-laws. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,mcm-law" + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. The value specifies the + physical address offset and length of the CCSR space + registers. + + - fsl,num-laws + Usage: required + Value type: <u32> + Definition: The value specifies the number of local access + windows for this device. + +===================================================================== + +MPX Coherency Module Node + +The MPX LAW node represents the region of CCSR space where MCM config +and error reporting registers exist, this is the second 4k (0x1000) +of CCSR space. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,CHIP-mcm", "fsl,mcm" where + CHIP is the processor (mpc8641, mpc8610, etc.) + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. The value specifies the + physical address offset and length of the CCSR space + registers. + + - interrupts + Usage: required + Value type: <prop-encoded-array> + + - interrupt-parent + Usage: required + Value type: <phandle> + +===================================================================== diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mcu-mpc8349emitx.txt b/Documentation/devicetree/bindings/powerpc/fsl/mcu-mpc8349emitx.txt new file mode 100644 index 00000000..0f766333 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mcu-mpc8349emitx.txt @@ -0,0 +1,17 @@ +Freescale MPC8349E-mITX-compatible Power Management Micro Controller Unit (MCU) + +Required properties: +- compatible : "fsl,<mcu-chip>-<board>", "fsl,mcu-mpc8349emitx". +- reg : should specify I2C address (0x0a). +- #gpio-cells : should be 2. +- gpio-controller : should be present. + +Example: + +mcu@0a { + #gpio-cells = <2>; + compatible = "fsl,mc9s08qg8-mpc8349emitx", + "fsl,mcu-mpc8349emitx"; + reg = <0x0a>; + gpio-controller; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt new file mode 100644 index 00000000..8832e879 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt @@ -0,0 +1,70 @@ +MPC5121 PSC Device Tree Bindings + +PSC in UART mode +---------------- + +For PSC in UART mode the needed PSC serial devices +are specified by fsl,mpc5121-psc-uart nodes in the +fsl,mpc5121-immr SoC node. Additionally the PSC FIFO +Controller node fsl,mpc5121-psc-fifo is requered there: + +fsl,mpc5121-psc-uart nodes +-------------------------- + +Required properties : + - compatible : Should contain "fsl,mpc5121-psc-uart" and "fsl,mpc5121-psc" + - cell-index : Index of the PSC in hardware + - reg : Offset and length of the register set for the PSC device + - interrupts : <a b> where a is the interrupt number of the + PSC FIFO Controller and b is a field that represents an + encoding of the sense and level information for the interrupt. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Recommended properties : + - fsl,rx-fifo-size : the size of the RX fifo slice (a multiple of 4) + - fsl,tx-fifo-size : the size of the TX fifo slice (a multiple of 4) + + +fsl,mpc5121-psc-fifo node +------------------------- + +Required properties : + - compatible : Should be "fsl,mpc5121-psc-fifo" + - reg : Offset and length of the register set for the PSC + FIFO Controller + - interrupts : <a b> where a is the interrupt number of the + PSC FIFO Controller and b is a field that represents an + encoding of the sense and level information for the interrupt. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + + +Example for a board using PSC0 and PSC1 devices in serial mode: + +serial@11000 { + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; + cell-index = <0>; + reg = <0x11000 0x100>; + interrupts = <40 0x8>; + interrupt-parent = < &ipic >; + fsl,rx-fifo-size = <16>; + fsl,tx-fifo-size = <16>; +}; + +serial@11100 { + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; + cell-index = <1>; + reg = <0x11100 0x100>; + interrupts = <40 0x8>; + interrupt-parent = < &ipic >; + fsl,rx-fifo-size = <16>; + fsl,tx-fifo-size = <16>; +}; + +pscfifo@11f00 { + compatible = "fsl,mpc5121-psc-fifo"; + reg = <0x11f00 0x100>; + interrupts = <40 0x8>; + interrupt-parent = < &ipic >; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpc5200.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpc5200.txt new file mode 100644 index 00000000..4ccb2cd5 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mpc5200.txt @@ -0,0 +1,198 @@ +MPC5200 Device Tree Bindings +---------------------------- + +(c) 2006-2009 Secret Lab Technologies Ltd +Grant Likely <grant.likely@secretlab.ca> + +Naming conventions +------------------ +For mpc5200 on-chip devices, the format for each compatible value is +<chip>-<device>[-<mode>]. The OS should be able to match a device driver +to the device based solely on the compatible value. If two drivers +match on the compatible list; the 'most compatible' driver should be +selected. + +The split between the MPC5200 and the MPC5200B leaves a bit of a +conundrum. How should the compatible property be set up to provide +maximum compatibility information; but still accurately describe the +chip? For the MPC5200; the answer is easy. Most of the SoC devices +originally appeared on the MPC5200. Since they didn't exist anywhere +else; the 5200 compatible properties will contain only one item; +"fsl,mpc5200-<device>". + +The 5200B is almost the same as the 5200, but not quite. It fixes +silicon bugs and it adds a small number of enhancements. Most of the +devices either provide exactly the same interface as on the 5200. A few +devices have extra functions but still have a backwards compatible mode. +To express this information as completely as possible, 5200B device trees +should have two items in the compatible list: + compatible = "fsl,mpc5200b-<device>","fsl,mpc5200-<device>"; + +It is *strongly* recommended that 5200B device trees follow this convention +(instead of only listing the base mpc5200 item). + +ie. ethernet on mpc5200: compatible = "fsl,mpc5200-fec"; + ethernet on mpc5200b: compatible = "fsl,mpc5200b-fec", "fsl,mpc5200-fec"; + +Modal devices, like PSCs, also append the configured function to the +end of the compatible field. ie. A PSC in i2s mode would specify +"fsl,mpc5200-psc-i2s", not "fsl,mpc5200-i2s". This convention is chosen to +avoid naming conflicts with non-psc devices providing the same +function. For example, "fsl,mpc5200-spi" and "fsl,mpc5200-psc-spi" describe +the mpc5200 simple spi device and a PSC spi mode respectively. + +At the time of writing, exact chip may be either 'fsl,mpc5200' or +'fsl,mpc5200b'. + +The soc node +------------ +This node describes the on chip SOC peripherals. Every mpc5200 based +board will have this node, and as such there is a common naming +convention for SOC devices. + +Required properties: +name description +---- ----------- +ranges Memory range of the internal memory mapped registers. + Should be <0 [baseaddr] 0xc000> +reg Should be <[baseaddr] 0x100> +compatible mpc5200: "fsl,mpc5200-immr" + mpc5200b: "fsl,mpc5200b-immr" +system-frequency 'fsystem' frequency in Hz; XLB, IPB, USB and PCI + clocks are derived from the fsystem clock. +bus-frequency IPB bus frequency in Hz. Clock rate + used by most of the soc devices. + +soc child nodes +--------------- +Any on chip SOC devices available to Linux must appear as soc5200 child nodes. + +Note: The tables below show the value for the mpc5200. A mpc5200b device +tree should use the "fsl,mpc5200b-<device>","fsl,mpc5200-<device>" form. + +Required soc5200 child nodes: +name compatible Description +---- ---------- ----------- +cdm@<addr> fsl,mpc5200-cdm Clock Distribution +interrupt-controller@<addr> fsl,mpc5200-pic need an interrupt + controller to boot +bestcomm@<addr> fsl,mpc5200-bestcomm Bestcomm DMA controller + +Recommended soc5200 child nodes; populate as needed for your board +name compatible Description +---- ---------- ----------- +timer@<addr> fsl,mpc5200-gpt General purpose timers +gpio@<addr> fsl,mpc5200-gpio MPC5200 simple gpio controller +gpio@<addr> fsl,mpc5200-gpio-wkup MPC5200 wakeup gpio controller +rtc@<addr> fsl,mpc5200-rtc Real time clock +mscan@<addr> fsl,mpc5200-mscan CAN bus controller +pci@<addr> fsl,mpc5200-pci PCI bridge +serial@<addr> fsl,mpc5200-psc-uart PSC in serial mode +i2s@<addr> fsl,mpc5200-psc-i2s PSC in i2s mode +ac97@<addr> fsl,mpc5200-psc-ac97 PSC in ac97 mode +spi@<addr> fsl,mpc5200-psc-spi PSC in spi mode +irda@<addr> fsl,mpc5200-psc-irda PSC in IrDA mode +spi@<addr> fsl,mpc5200-spi MPC5200 spi device +ethernet@<addr> fsl,mpc5200-fec MPC5200 ethernet device +ata@<addr> fsl,mpc5200-ata IDE ATA interface +i2c@<addr> fsl,mpc5200-i2c I2C controller +usb@<addr> fsl,mpc5200-ohci,ohci-be USB controller +xlb@<addr> fsl,mpc5200-xlb XLB arbitrator + +fsl,mpc5200-gpt nodes +--------------------- +On the mpc5200 and 5200b, GPT0 has a watchdog timer function. If the board +design supports the internal wdt, then the device node for GPT0 should +include the empty property 'fsl,has-wdt'. Note that this does not activate +the watchdog. The timer will function as a GPT if the timer api is used, and +it will function as watchdog if the watchdog device is used. The watchdog +mode has priority over the gpt mode, i.e. if the watchdog is activated, any +gpt api call to this timer will fail with -EBUSY. + +If you add the property + fsl,wdt-on-boot = <n>; +GPT0 will be marked as in-use watchdog, i.e. blocking every gpt access to it. +If n>0, the watchdog is started with a timeout of n seconds. If n=0, the +configuration of the watchdog is not touched. This is useful in two cases: +- just mark GPT0 as watchdog, blocking gpt accesses, and configure it later; +- do not touch a configuration assigned by the boot loader which supervises + the boot process itself. + +The watchdog will respect the CONFIG_WATCHDOG_NOWAYOUT option. + +An mpc5200-gpt can be used as a single line GPIO controller. To do so, +add the following properties to the gpt node: + gpio-controller; + #gpio-cells = <2>; +When referencing the GPIO line from another node, the first cell must always +be zero and the second cell represents the gpio flags and described in the +gpio device tree binding. + +An mpc5200-gpt can be used as a single line edge sensitive interrupt +controller. To do so, add the following properties to the gpt node: + interrupt-controller; + #interrupt-cells = <1>; +When referencing the IRQ line from another node, the cell represents the +sense mode; 1 for edge rising, 2 for edge falling. + +fsl,mpc5200-psc nodes +--------------------- +The PSCs should include a cell-index which is the index of the PSC in +hardware. cell-index is used to determine which shared SoC registers to +use when setting up PSC clocking. cell-index number starts at '0'. ie: + PSC1 has 'cell-index = <0>' + PSC4 has 'cell-index = <3>' + +PSC in i2s mode: The mpc5200 and mpc5200b PSCs are not compatible when in +i2s mode. An 'mpc5200b-psc-i2s' node cannot include 'mpc5200-psc-i2s' in the +compatible field. + + +fsl,mpc5200-gpio and fsl,mpc5200-gpio-wkup nodes +------------------------------------------------ +Each GPIO controller node should have the empty property gpio-controller and +#gpio-cells set to 2. First cell is the GPIO number which is interpreted +according to the bit numbers in the GPIO control registers. The second cell +is for flags which is currently unused. + +fsl,mpc5200-fec nodes +--------------------- +The FEC node can specify one of the following properties to configure +the MII link: +- fsl,7-wire-mode - An empty property that specifies the link uses 7-wire + mode instead of MII +- current-speed - Specifies that the MII should be configured for a fixed + speed. This property should contain two cells. The + first cell specifies the speed in Mbps and the second + should be '0' for half duplex and '1' for full duplex +- phy-handle - Contains a phandle to an Ethernet PHY. + +Interrupt controller (fsl,mpc5200-pic) node +------------------------------------------- +The mpc5200 pic binding splits hardware IRQ numbers into two levels. The +split reflects the layout of the PIC hardware itself, which groups +interrupts into one of three groups; CRIT, MAIN or PERP. Also, the +Bestcomm dma engine has it's own set of interrupt sources which are +cascaded off of peripheral interrupt 0, which the driver interprets as a +fourth group, SDMA. + +The interrupts property for device nodes using the mpc5200 pic consists +of three cells; <L1 L2 level> + + L1 := [CRIT=0, MAIN=1, PERP=2, SDMA=3] + L2 := interrupt number; directly mapped from the value in the + "ICTL PerStat, MainStat, CritStat Encoded Register" + level := [LEVEL_HIGH=0, EDGE_RISING=1, EDGE_FALLING=2, LEVEL_LOW=3] + +For external IRQs, use the following interrupt property values (how to +specify external interrupts is a frequently asked question): +External interrupts: + external irq0: interrupts = <0 0 n>; + external irq1: interrupts = <1 1 n>; + external irq2: interrupts = <1 2 n>; + external irq3: interrupts = <1 3 n>; +'n' is sense (0: level high, 1: edge rising, 2: edge falling 3: level low) + +fsl,mpc5200-mscan nodes +----------------------- +See file can.txt in this directory. diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpic-msgr.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpic-msgr.txt new file mode 100644 index 00000000..bc8ded64 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mpic-msgr.txt @@ -0,0 +1,63 @@ +* FSL MPIC Message Registers + +This binding specifies what properties must be available in the device tree +representation of the message register blocks found in some FSL MPIC +implementations. + +Required properties: + + - compatible: Specifies the compatibility list for the message register + block. The type shall be <string-list> and the value shall be of the form + "fsl,mpic-v<version>-msgr", where <version> is the version number of + the MPIC containing the message registers. + + - reg: Specifies the base physical address(s) and size(s) of the + message register block's addressable register space. The type shall be + <prop-encoded-array>. + + - interrupts: Specifies a list of interrupt-specifiers which are available + for receiving interrupts. Interrupt-specifier consists of two cells: first + cell is interrupt-number and second cell is level-sense. The type shall be + <prop-encoded-array>. + +Optional properties: + + - mpic-msgr-receive-mask: Specifies what registers in the containing block + are allowed to receive interrupts. The value is a bit mask where a set + bit at bit 'n' indicates that message register 'n' can receive interrupts. + Note that "bit 'n'" is numbered from LSB for PPC hardware. The type shall + be <u32>. If not present, then all of the message registers in the block + are available. + +Aliases: + + An alias should be created for every message register block. They are not + required, though. However, a particular implementation of this binding + may require aliases to be present. Aliases are of the form + 'mpic-msgr-block<n>', where <n> is an integer specifying the block's number. + Numbers shall start at 0. + +Example: + + aliases { + mpic-msgr-block0 = &mpic_msgr_block0; + mpic-msgr-block1 = &mpic_msgr_block1; + }; + + mpic_msgr_block0: mpic-msgr-block@41400 { + compatible = "fsl,mpic-v3.1-msgr"; + reg = <0x41400 0x200>; + // Message registers 0 and 2 in this block can receive interrupts on + // sources 0xb0 and 0xb2, respectively. + interrupts = <0xb0 2 0xb2 2>; + mpic-msgr-receive-mask = <0x5>; + }; + + mpic_msgr_block1: mpic-msgr-block@42400 { + compatible = "fsl,mpic-v3.1-msgr"; + reg = <0x42400 0x200>; + // Message registers 0 and 2 in this block can receive interrupts on + // sources 0xb4 and 0xb6, respectively. + interrupts = <0xb4 2 0xb6 2>; + mpic-msgr-receive-mask = <0x5>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpic-timer.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpic-timer.txt new file mode 100644 index 00000000..df419581 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mpic-timer.txt @@ -0,0 +1,38 @@ +* Freescale MPIC timers + +Required properties: +- compatible: "fsl,mpic-global-timer" + +- reg : Contains two regions. The first is the main timer register bank + (GTCCRxx, GTBCRxx, GTVPRxx, GTDRxx). The second is the timer control + register (TCRx) for the group. + +- fsl,available-ranges: use <start count> style section to define which + timer interrupts can be used. This property is optional; without this, + all timers within the group can be used. + +- interrupts: one interrupt per timer in the group, in order, starting + with timer zero. If timer-available-ranges is present, only the + interrupts that correspond to available timers shall be present. + +Example: + /* Note that this requires #interrupt-cells to be 4 */ + timer0: timer@41100 { + compatible = "fsl,mpic-global-timer"; + reg = <0x41100 0x100 0x41300 4>; + + /* Another AMP partition is using timers 0 and 1 */ + fsl,available-ranges = <2 2>; + + interrupts = <2 0 3 0 + 3 0 3 0>; + }; + + timer1: timer@42100 { + compatible = "fsl,mpic-global-timer"; + reg = <0x42100 0x100 0x42300 4>; + interrupts = <4 0 3 0 + 5 0 3 0 + 6 0 3 0 + 7 0 3 0>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt new file mode 100644 index 00000000..dc574463 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt @@ -0,0 +1,231 @@ +===================================================================== +Freescale MPIC Interrupt Controller Node +Copyright (C) 2010,2011 Freescale Semiconductor Inc. +===================================================================== + +The Freescale MPIC interrupt controller is found on all PowerQUICC +and QorIQ processors and is compatible with the Open PIC. The +notable difference from Open PIC binding is the addition of 2 +additional cells in the interrupt specifier defining interrupt type +information. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Shall include "fsl,mpic". Freescale MPIC + controllers compatible with this binding have Block + Revision Registers BRR1 and BRR2 at offset 0x0 and + 0x10 in the MPIC. + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical + offset and length of the device's registers within the + CCSR address space. + + - interrupt-controller + Usage: required + Value type: <empty> + Definition: Specifies that this node is an interrupt + controller + + - #interrupt-cells + Usage: required + Value type: <u32> + Definition: Shall be 2 or 4. A value of 2 means that interrupt + specifiers do not contain the interrupt-type or type-specific + information cells. + + - #address-cells + Usage: required + Value type: <u32> + Definition: Shall be 0. + + - pic-no-reset + Usage: optional + Value type: <empty> + Definition: The presence of this property specifies that the + MPIC must not be reset by the client program, and that + the boot program has initialized all interrupt source + configuration registers to a sane state-- masked or + directed at other cores. This ensures that the client + program will not receive interrupts for sources not belonging + to the client. The presence of this property also mandates + that any initialization related to interrupt sources shall + be limited to sources explicitly referenced in the device tree. + + - big-endian + Usage: optional + Value type: <empty> + If present the MPIC will be assumed to be big-endian. Some + device-trees omit this property on MPIC nodes even when the MPIC is + in fact big-endian, so certain boards override this property. + + - single-cpu-affinity + Usage: optional + Value type: <empty> + If present the MPIC will be assumed to only be able to route + non-IPI interrupts to a single CPU at a time (EG: Freescale MPIC). + + - last-interrupt-source + Usage: optional + Value type: <u32> + Some MPICs do not correctly report the number of hardware sources + in the global feature registers. If specified, this field will + override the value read from MPIC_GREG_FEATURE_LAST_SRC. + +INTERRUPT SPECIFIER DEFINITION + + Interrupt specifiers consists of 4 cells encoded as + follows: + + <1st-cell> interrupt-number + + Identifies the interrupt source. The meaning + depends on the type of interrupt. + + Note: If the interrupt-type cell is undefined + (i.e. #interrupt-cells = 2), this cell + should be interpreted the same as for + interrupt-type 0-- i.e. an external or + normal SoC device interrupt. + + <2nd-cell> level-sense information, encoded as follows: + 0 = low-to-high edge triggered + 1 = active low level-sensitive + 2 = active high level-sensitive + 3 = high-to-low edge triggered + + <3rd-cell> interrupt-type + + The following types are supported: + + 0 = external or normal SoC device interrupt + + The interrupt-number cell contains + the SoC device interrupt number. The + type-specific cell is undefined. The + interrupt-number is derived from the + MPIC a block of registers referred to as + the "Interrupt Source Configuration Registers". + Each source has 32-bytes of registers + (vector/priority and destination) in this + region. So interrupt 0 is at offset 0x0, + interrupt 1 is at offset 0x20, and so on. + + 1 = error interrupt + + The interrupt-number cell contains + the SoC device interrupt number for + the error interrupt. The type-specific + cell identifies the specific error + interrupt number. + + 2 = MPIC inter-processor interrupt (IPI) + + The interrupt-number cell identifies + the MPIC IPI number. The type-specific + cell is undefined. + + 3 = MPIC timer interrupt + + The interrupt-number cell identifies + the MPIC timer number. The type-specific + cell is undefined. + + <4th-cell> type-specific information + + The type-specific cell is encoded as follows: + + - For interrupt-type 1 (error interrupt), + the type-specific cell contains the + bit number of the error interrupt in the + Error Interrupt Summary Register. + +EXAMPLE 1 + /* + * mpic interrupt controller with 4 cells per specifier + */ + mpic: pic@40000 { + compatible = "fsl,mpic"; + interrupt-controller; + #interrupt-cells = <4>; + #address-cells = <0>; + reg = <0x40000 0x40000>; + }; + +EXAMPLE 2 + /* + * The MPC8544 I2C controller node has an internal + * interrupt number of 27. As per the reference manual + * this corresponds to interrupt source configuration + * registers at 0x5_0560. + * + * The interrupt source configuration registers begin + * at 0x5_0000. + * + * To compute the interrupt specifier interrupt number + * + * 0x560 >> 5 = 43 + * + * The interrupt source configuration registers begin + * at 0x5_0000, and so the i2c vector/priority registers + * are at 0x5_0560. + */ + i2c@3000 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + compatible = "fsl-i2c"; + reg = <0x3000 0x100>; + interrupts = <43 2>; + interrupt-parent = <&mpic>; + dfsrr; + }; + + +EXAMPLE 3 + /* + * Definition of a node defining the 4 + * MPIC IPI interrupts. Note the interrupt + * type of 2. + */ + ipi@410a0 { + compatible = "fsl,mpic-ipi"; + reg = <0x40040 0x10>; + interrupts = <0 0 2 0 + 1 0 2 0 + 2 0 2 0 + 3 0 2 0>; + }; + +EXAMPLE 4 + /* + * Definition of a node defining the MPIC + * global timers. Note the interrupt + * type of 3. + */ + timer0: timer@41100 { + compatible = "fsl,mpic-global-timer"; + reg = <0x41100 0x100 0x41300 4>; + interrupts = <0 0 3 0 + 1 0 3 0 + 2 0 3 0 + 3 0 3 0>; + }; + +EXAMPLE 5 + /* + * Definition of an error interrupt (interrupt type 1). + * SoC interrupt number is 16 and the specific error + * interrupt bit in the error interrupt summary register + * is 23. + */ + memory-controller@8000 { + compatible = "fsl,p4080-memory-controller"; + reg = <0x8000 0x1000>; + interrupts = <16 2 1 23>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt b/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt new file mode 100644 index 00000000..5693877a --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt @@ -0,0 +1,87 @@ +* Freescale MSI interrupt controller + +Required properties: +- compatible : compatible list, contains 2 entries, + first is "fsl,CHIP-msi", where CHIP is the processor(mpc8610, mpc8572, + etc.) and the second is "fsl,mpic-msi" or "fsl,ipic-msi" depending on + the parent type. + +- reg : It may contain one or two regions. The first region should contain + the address and the length of the shared message interrupt register set. + The second region should contain the address of aliased MSIIR register for + platforms that have such an alias. + +- msi-available-ranges: use <start count> style section to define which + msi interrupt can be used in the 256 msi interrupts. This property is + optional, without this, all the 256 MSI interrupts can be used. + Each available range must begin and end on a multiple of 32 (i.e. + no splitting an individual MSI register or the associated PIC interrupt). + +- interrupts : each one of the interrupts here is one entry per 32 MSIs, + and routed to the host interrupt controller. the interrupts should + be set as edge sensitive. If msi-available-ranges is present, only + the interrupts that correspond to available ranges shall be present. + +- interrupt-parent: the phandle for the interrupt controller + that services interrupts for this device. for 83xx cpu, the interrupts + are routed to IPIC, and for 85xx/86xx cpu the interrupts are routed + to MPIC. + +Optional properties: +- msi-address-64: 64-bit PCI address of the MSIIR register. The MSIIR register + is used for MSI messaging. The address of MSIIR in PCI address space is + the MSI message address. + + This property may be used in virtualized environments where the hypervisor + has created an alternate mapping for the MSIR block. See below for an + explanation. + + +Example: + msi@41600 { + compatible = "fsl,mpc8610-msi", "fsl,mpic-msi"; + reg = <0x41600 0x80>; + msi-available-ranges = <0 0x100>; + interrupts = < + 0xe0 0 + 0xe1 0 + 0xe2 0 + 0xe3 0 + 0xe4 0 + 0xe5 0 + 0xe6 0 + 0xe7 0>; + interrupt-parent = <&mpic>; + }; + +The Freescale hypervisor and msi-address-64 +------------------------------------------- +Normally, PCI devices have access to all of CCSR via an ATMU mapping. The +Freescale MSI driver calculates the address of MSIIR (in the MSI register +block) and sets that address as the MSI message address. + +In a virtualized environment, the hypervisor may need to create an IOMMU +mapping for MSIIR. The Freescale ePAPR hypervisor has this requirement +because of hardware limitations of the Peripheral Access Management Unit +(PAMU), which is currently the only IOMMU that the hypervisor supports. +The ATMU is programmed with the guest physical address, and the PAMU +intercepts transactions and reroutes them to the true physical address. + +In the PAMU, each PCI controller is given only one primary window. The +PAMU restricts DMA operations so that they can only occur within a window. +Because PCI devices must be able to DMA to memory, the primary window must +be used to cover all of the guest's memory space. + +PAMU primary windows can be divided into 256 subwindows, and each +subwindow can have its own address mapping ("guest physical" to "true +physical"). However, each subwindow has to have the same alignment, which +means they cannot be located at just any address. Because of these +restrictions, it is usually impossible to create a 4KB subwindow that +covers MSIIR where it's normally located. + +Therefore, the hypervisor has to create a subwindow inside the same +primary window used for memory, but mapped to the MSIR block (where MSIIR +lives). The first subwindow after the end of guest memory is used for +this. The address specified in the msi-address-64 property is the PCI +address of MSIIR. The hypervisor configures the PAMU to map that address to +the true physical address of MSIIR. diff --git a/Documentation/devicetree/bindings/powerpc/fsl/pmc.txt b/Documentation/devicetree/bindings/powerpc/fsl/pmc.txt new file mode 100644 index 00000000..07256b7f --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/pmc.txt @@ -0,0 +1,63 @@ +* Power Management Controller + +Properties: +- compatible: "fsl,<chip>-pmc". + + "fsl,mpc8349-pmc" should be listed for any chip whose PMC is + compatible. "fsl,mpc8313-pmc" should also be listed for any chip + whose PMC is compatible, and implies deep-sleep capability. + + "fsl,mpc8548-pmc" should be listed for any chip whose PMC is + compatible. "fsl,mpc8536-pmc" should also be listed for any chip + whose PMC is compatible, and implies deep-sleep capability. + + "fsl,mpc8641d-pmc" should be listed for any chip whose PMC is + compatible; all statements below that apply to "fsl,mpc8548-pmc" also + apply to "fsl,mpc8641d-pmc". + + Compatibility does not include bit assignments in SCCR/PMCDR/DEVDISR; these + bit assignments are indicated via the sleep specifier in each device's + sleep property. + +- reg: For devices compatible with "fsl,mpc8349-pmc", the first resource + is the PMC block, and the second resource is the Clock Configuration + block. + + For devices compatible with "fsl,mpc8548-pmc", the first resource + is a 32-byte block beginning with DEVDISR. + +- interrupts: For "fsl,mpc8349-pmc"-compatible devices, the first + resource is the PMC block interrupt. + +- fsl,mpc8313-wakeup-timer: For "fsl,mpc8313-pmc"-compatible devices, + this is a phandle to an "fsl,gtm" node on which timer 4 can be used as + a wakeup source from deep sleep. + +Sleep specifiers: + + fsl,mpc8349-pmc: Sleep specifiers consist of one cell. For each bit + that is set in the cell, the corresponding bit in SCCR will be saved + and cleared on suspend, and restored on resume. This sleep controller + supports disabling and resuming devices at any time. + + fsl,mpc8536-pmc: Sleep specifiers consist of three cells, the third of + which will be ORed into PMCDR upon suspend, and cleared from PMCDR + upon resume. The first two cells are as described for fsl,mpc8578-pmc. + This sleep controller only supports disabling devices during system + sleep, or permanently. + + fsl,mpc8548-pmc: Sleep specifiers consist of one or two cells, the + first of which will be ORed into DEVDISR (and the second into + DEVDISR2, if present -- this cell should be zero or absent if the + hardware does not have DEVDISR2) upon a request for permanent device + disabling. This sleep controller does not support configuring devices + to disable during system sleep (unless supported by another compatible + match), or dynamically. + +Example: + + power@b00 { + compatible = "fsl,mpc8313-pmc", "fsl,mpc8349-pmc"; + reg = <0xb00 0x100 0xa00 0x100>; + interrupts = <80 8>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/srio-rmu.txt b/Documentation/devicetree/bindings/powerpc/fsl/srio-rmu.txt new file mode 100644 index 00000000..b9a8a2bc --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/srio-rmu.txt @@ -0,0 +1,163 @@ +Message unit node: + +For SRIO controllers that implement the message unit as part of the controller +this node is required. For devices with RMAN this node should NOT exist. The +node is composed of three types of sub-nodes ("fsl-srio-msg-unit", +"fsl-srio-dbell-unit" and "fsl-srio-port-write-unit"). + +See srio.txt for more details about generic SRIO controller details. + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,srio-rmu-vX.Y", "fsl,srio-rmu". + + The version X.Y should match the general SRIO controller's IP Block + revision register's Major(X) and Minor (Y) value. + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address and + length of the SRIO configuration registers for message units + and doorbell units. + + - fsl,liodn + Usage: optional-but-recommended (for devices with PAMU) + Value type: <prop-encoded-array> + Definition: The logical I/O device number for the PAMU (IOMMU) to be + correctly configured for SRIO accesses. The property should + not exist on devices that do not support PAMU. + + The LIODN value is associated with all RMU transactions + (msg-unit, doorbell, port-write). + +Sub-Nodes for RMU: The RMU node is composed of multiple sub-nodes that +correspond to the actual sub-controllers in the RMU. The manual for a given +SoC will detail which and how many of these sub-controllers are implemented. + +Message Unit: + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,srio-msg-unit-vX.Y", "fsl,srio-msg-unit". + + The version X.Y should match the general SRIO controller's IP Block + revision register's Major(X) and Minor (Y) value. + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address and + length of the SRIO configuration registers for message units + and doorbell units. + + - interrupts + Usage: required + Value type: <prop_encoded-array> + Definition: Specifies the interrupts generated by this device. The + value of the interrupts property consists of one interrupt + specifier. The format of the specifier is defined by the + binding document describing the node's interrupt parent. + + A pair of IRQs are specified in this property. The first + element is associated with the transmit (TX) interrupt and the + second element is associated with the receive (RX) interrupt. + +Doorbell Unit: + + - compatible + Usage: required + Value type: <string> + Definition: Must include: + "fsl,srio-dbell-unit-vX.Y", "fsl,srio-dbell-unit" + + The version X.Y should match the general SRIO controller's IP Block + revision register's Major(X) and Minor (Y) value. + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address and + length of the SRIO configuration registers for message units + and doorbell units. + + - interrupts + Usage: required + Value type: <prop_encoded-array> + Definition: Specifies the interrupts generated by this device. The + value of the interrupts property consists of one interrupt + specifier. The format of the specifier is defined by the + binding document describing the node's interrupt parent. + + A pair of IRQs are specified in this property. The first + element is associated with the transmit (TX) interrupt and the + second element is associated with the receive (RX) interrupt. + +Port-Write Unit: + + - compatible + Usage: required + Value type: <string> + Definition: Must include: + "fsl,srio-port-write-unit-vX.Y", "fsl,srio-port-write-unit" + + The version X.Y should match the general SRIO controller's IP Block + revision register's Major(X) and Minor (Y) value. + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address and + length of the SRIO configuration registers for message units + and doorbell units. + + - interrupts + Usage: required + Value type: <prop_encoded-array> + Definition: Specifies the interrupts generated by this device. The + value of the interrupts property consists of one interrupt + specifier. The format of the specifier is defined by the + binding document describing the node's interrupt parent. + + A single IRQ that handles port-write conditions is + specified by this property. (Typically shared with error). + + Note: All other standard properties (see the ePAPR) are allowed + but are optional. + +Example: + rmu: rmu@d3000 { + compatible = "fsl,srio-rmu"; + reg = <0xd3000 0x400>; + ranges = <0x0 0xd3000 0x400>; + fsl,liodn = <0xc8>; + + message-unit@0 { + compatible = "fsl,srio-msg-unit"; + reg = <0x0 0x100>; + interrupts = < + 60 2 0 0 /* msg1_tx_irq */ + 61 2 0 0>;/* msg1_rx_irq */ + }; + message-unit@100 { + compatible = "fsl,srio-msg-unit"; + reg = <0x100 0x100>; + interrupts = < + 62 2 0 0 /* msg2_tx_irq */ + 63 2 0 0>;/* msg2_rx_irq */ + }; + doorbell-unit@400 { + compatible = "fsl,srio-dbell-unit"; + reg = <0x400 0x80>; + interrupts = < + 56 2 0 0 /* bell_outb_irq */ + 57 2 0 0>;/* bell_inb_irq */ + }; + port-write-unit@4e0 { + compatible = "fsl,srio-port-write-unit"; + reg = <0x4e0 0x20>; + interrupts = <16 2 1 11>; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/srio.txt b/Documentation/devicetree/bindings/powerpc/fsl/srio.txt new file mode 100644 index 00000000..b039bcbe --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/srio.txt @@ -0,0 +1,103 @@ +* Freescale Serial RapidIO (SRIO) Controller + +RapidIO port node: +Properties: + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,srio" for IP blocks with IP Block + Revision Register (SRIO IPBRR1) Major ID equal to 0x01c0. + + Optionally, a compatiable string of "fsl,srio-vX.Y" where X is Major + version in IP Block Revision Register and Y is Minor version. If this + compatiable is provided it should be ordered before "fsl,srio". + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address and + length of the SRIO configuration registers. The size should + be set to 0x11000. + + - interrupts + Usage: required + Value type: <prop_encoded-array> + Definition: Specifies the interrupts generated by this device. The + value of the interrupts property consists of one interrupt + specifier. The format of the specifier is defined by the + binding document describing the node's interrupt parent. + + A single IRQ that handles error conditions is specified by this + property. (Typically shared with port-write). + + - fsl,srio-rmu-handle: + Usage: required if rmu node is defined + Value type: <phandle> + Definition: A single <phandle> value that points to the RMU. + (See srio-rmu.txt for more details on RMU node binding) + +Port Child Nodes: There should a port child node for each port that exists in +the controller. The ports are numbered starting at one (1) and should have +the following properties: + + - cell-index + Usage: required + Value type: <u32> + Definition: A standard property. Matches the port id. + + - ranges + Usage: required if local access windows preset + Value type: <prop-encoded-array> + Definition: A standard property. Utilized to describe the memory mapped + IO space utilized by the controller. This corresponds to the + setting of the local access windows that are targeted to this + SRIO port. + + - fsl,liodn + Usage: optional-but-recommended (for devices with PAMU) + Value type: <prop-encoded-array> + Definition: The logical I/O device number for the PAMU (IOMMU) to be + correctly configured for SRIO accesses. The property should + not exist on devices that do not support PAMU. + + For HW (ie, the P4080) that only supports a LIODN for both + memory and maintenance transactions then a single LIODN is + represented in the property for both transactions. + + For HW (ie, the P304x/P5020, etc) that supports an LIODN for + memory transactions and a unique LIODN for maintenance + transactions then a pair of LIODNs are represented in the + property. Within the pair, the first element represents the + LIODN associated with memory transactions and the second element + represents the LIODN associated with maintenance transactions + for the port. + +Note: All other standard properties (see ePAPR) are allowed but are optional. + +Example: + + rapidio: rapidio@ffe0c0000 { + #address-cells = <2>; + #size-cells = <2>; + reg = <0xf 0xfe0c0000 0 0x11000>; + compatible = "fsl,srio"; + interrupts = <16 2 1 11>; /* err_irq */ + fsl,srio-rmu-handle = <&rmu>; + ranges; + + port1 { + cell-index = <1>; + #address-cells = <2>; + #size-cells = <2>; + fsl,liodn = <34>; + ranges = <0 0 0xc 0x20000000 0 0x10000000>; + }; + + port2 { + cell-index = <2>; + #address-cells = <2>; + #size-cells = <2>; + fsl,liodn = <48>; + ranges = <0 0 0xc 0x30000000 0 0x10000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/ssi.txt b/Documentation/devicetree/bindings/powerpc/fsl/ssi.txt new file mode 100644 index 00000000..5ff76c9c --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/ssi.txt @@ -0,0 +1,73 @@ +Freescale Synchronous Serial Interface + +The SSI is a serial device that communicates with audio codecs. It can +be programmed in AC97, I2S, left-justified, or right-justified modes. + +Required properties: +- compatible: Compatible list, contains "fsl,ssi". +- cell-index: The SSI, <0> = SSI1, <1> = SSI2, and so on. +- reg: Offset and length of the register set for the device. +- interrupts: <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and + level information for the interrupt. This should be + encoded based on the information in section 2) + depending on the type of interrupt controller you + have. +- interrupt-parent: The phandle for the interrupt controller that + services interrupts for this device. +- fsl,mode: The operating mode for the SSI interface. + "i2s-slave" - I2S mode, SSI is clock slave + "i2s-master" - I2S mode, SSI is clock master + "lj-slave" - left-justified mode, SSI is clock slave + "lj-master" - l.j. mode, SSI is clock master + "rj-slave" - right-justified mode, SSI is clock slave + "rj-master" - r.j., SSI is clock master + "ac97-slave" - AC97 mode, SSI is clock slave + "ac97-master" - AC97 mode, SSI is clock master +- fsl,playback-dma: Phandle to a node for the DMA channel to use for + playback of audio. This is typically dictated by SOC + design. See the notes below. +- fsl,capture-dma: Phandle to a node for the DMA channel to use for + capture (recording) of audio. This is typically dictated + by SOC design. See the notes below. +- fsl,fifo-depth: The number of elements in the transmit and receive FIFOs. + This number is the maximum allowed value for SFCSR[TFWM0]. +- fsl,ssi-asynchronous: + If specified, the SSI is to be programmed in asynchronous + mode. In this mode, pins SRCK, STCK, SRFS, and STFS must + all be connected to valid signals. In synchronous mode, + SRCK and SRFS are ignored. Asynchronous mode allows + playback and capture to use different sample sizes and + sample rates. Some drivers may require that SRCK and STCK + be connected together, and SRFS and STFS be connected + together. This would still allow different sample sizes, + but not different sample rates. + +Optional properties: +- codec-handle: Phandle to a 'codec' node that defines an audio + codec connected to this SSI. This node is typically + a child of an I2C or other control node. + +Child 'codec' node required properties: +- compatible: Compatible list, contains the name of the codec + +Child 'codec' node optional properties: +- clock-frequency: The frequency of the input clock, which typically comes + from an on-board dedicated oscillator. + +Notes on fsl,playback-dma and fsl,capture-dma: + +On SOCs that have an SSI, specific DMA channels are hard-wired for playback +and capture. On the MPC8610, for example, SSI1 must use DMA channel 0 for +playback and DMA channel 1 for capture. SSI2 must use DMA channel 2 for +playback and DMA channel 3 for capture. The developer can choose which +DMA controller to use, but the channels themselves are hard-wired. The +purpose of these two properties is to represent this hardware design. + +The device tree nodes for the DMA channels that are referenced by +"fsl,playback-dma" and "fsl,capture-dma" must be marked as compatible with +"fsl,ssi-dma-channel". The SOC-specific compatible string (e.g. +"fsl,mpc8610-dma-channel") can remain. If these nodes are left as +"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel", then the generic Elo DMA +drivers (fsldma) will attempt to use them, and it will conflict with the +sound drivers. diff --git a/Documentation/devicetree/bindings/powerpc/nintendo/gamecube.txt b/Documentation/devicetree/bindings/powerpc/nintendo/gamecube.txt new file mode 100644 index 00000000..b558585b --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/nintendo/gamecube.txt @@ -0,0 +1,109 @@ + +Nintendo GameCube device tree +============================= + +1) The "flipper" node + + This node represents the multi-function "Flipper" chip, which packages + many of the devices found in the Nintendo GameCube. + + Required properties: + + - compatible : Should be "nintendo,flipper" + +1.a) The Video Interface (VI) node + + Represents the interface between the graphics processor and a external + video encoder. + + Required properties: + + - compatible : should be "nintendo,flipper-vi" + - reg : should contain the VI registers location and length + - interrupts : should contain the VI interrupt + +1.b) The Processor Interface (PI) node + + Represents the data and control interface between the main processor + and graphics and audio processor. + + Required properties: + + - compatible : should be "nintendo,flipper-pi" + - reg : should contain the PI registers location and length + +1.b.i) The "Flipper" interrupt controller node + + Represents the interrupt controller within the "Flipper" chip. + The node for the "Flipper" interrupt controller must be placed under + the PI node. + + Required properties: + + - compatible : should be "nintendo,flipper-pic" + +1.c) The Digital Signal Procesor (DSP) node + + Represents the digital signal processor interface, designed to offload + audio related tasks. + + Required properties: + + - compatible : should be "nintendo,flipper-dsp" + - reg : should contain the DSP registers location and length + - interrupts : should contain the DSP interrupt + +1.c.i) The Auxiliary RAM (ARAM) node + + Represents the non cpu-addressable ram designed mainly to store audio + related information. + The ARAM node must be placed under the DSP node. + + Required properties: + + - compatible : should be "nintendo,flipper-aram" + - reg : should contain the ARAM start (zero-based) and length + +1.d) The Disk Interface (DI) node + + Represents the interface used to communicate with mass storage devices. + + Required properties: + + - compatible : should be "nintendo,flipper-di" + - reg : should contain the DI registers location and length + - interrupts : should contain the DI interrupt + +1.e) The Audio Interface (AI) node + + Represents the interface to the external 16-bit stereo digital-to-analog + converter. + + Required properties: + + - compatible : should be "nintendo,flipper-ai" + - reg : should contain the AI registers location and length + - interrupts : should contain the AI interrupt + +1.f) The Serial Interface (SI) node + + Represents the interface to the four single bit serial interfaces. + The SI is a proprietary serial interface used normally to control gamepads. + It's NOT a RS232-type interface. + + Required properties: + + - compatible : should be "nintendo,flipper-si" + - reg : should contain the SI registers location and length + - interrupts : should contain the SI interrupt + +1.g) The External Interface (EXI) node + + Represents the multi-channel SPI-like interface. + + Required properties: + + - compatible : should be "nintendo,flipper-exi" + - reg : should contain the EXI registers location and length + - interrupts : should contain the EXI interrupt + diff --git a/Documentation/devicetree/bindings/powerpc/nintendo/wii.txt b/Documentation/devicetree/bindings/powerpc/nintendo/wii.txt new file mode 100644 index 00000000..36afa322 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/nintendo/wii.txt @@ -0,0 +1,184 @@ + +Nintendo Wii device tree +======================== + +0) The root node + + This node represents the Nintendo Wii video game console. + + Required properties: + + - model : Should be "nintendo,wii" + - compatible : Should be "nintendo,wii" + +1) The "hollywood" node + + This node represents the multi-function "Hollywood" chip, which packages + many of the devices found in the Nintendo Wii. + + Required properties: + + - compatible : Should be "nintendo,hollywood" + +1.a) The Video Interface (VI) node + + Represents the interface between the graphics processor and a external + video encoder. + + Required properties: + + - compatible : should be "nintendo,hollywood-vi","nintendo,flipper-vi" + - reg : should contain the VI registers location and length + - interrupts : should contain the VI interrupt + +1.b) The Processor Interface (PI) node + + Represents the data and control interface between the main processor + and graphics and audio processor. + + Required properties: + + - compatible : should be "nintendo,hollywood-pi","nintendo,flipper-pi" + - reg : should contain the PI registers location and length + +1.b.i) The "Flipper" interrupt controller node + + Represents the "Flipper" interrupt controller within the "Hollywood" chip. + The node for the "Flipper" interrupt controller must be placed under + the PI node. + + Required properties: + + - #interrupt-cells : <1> + - compatible : should be "nintendo,flipper-pic" + - interrupt-controller + +1.c) The Digital Signal Procesor (DSP) node + + Represents the digital signal processor interface, designed to offload + audio related tasks. + + Required properties: + + - compatible : should be "nintendo,hollywood-dsp","nintendo,flipper-dsp" + - reg : should contain the DSP registers location and length + - interrupts : should contain the DSP interrupt + +1.d) The Serial Interface (SI) node + + Represents the interface to the four single bit serial interfaces. + The SI is a proprietary serial interface used normally to control gamepads. + It's NOT a RS232-type interface. + + Required properties: + + - compatible : should be "nintendo,hollywood-si","nintendo,flipper-si" + - reg : should contain the SI registers location and length + - interrupts : should contain the SI interrupt + +1.e) The Audio Interface (AI) node + + Represents the interface to the external 16-bit stereo digital-to-analog + converter. + + Required properties: + + - compatible : should be "nintendo,hollywood-ai","nintendo,flipper-ai" + - reg : should contain the AI registers location and length + - interrupts : should contain the AI interrupt + +1.f) The External Interface (EXI) node + + Represents the multi-channel SPI-like interface. + + Required properties: + + - compatible : should be "nintendo,hollywood-exi","nintendo,flipper-exi" + - reg : should contain the EXI registers location and length + - interrupts : should contain the EXI interrupt + +1.g) The Open Host Controller Interface (OHCI) nodes + + Represent the USB 1.x Open Host Controller Interfaces. + + Required properties: + + - compatible : should be "nintendo,hollywood-usb-ohci","usb-ohci" + - reg : should contain the OHCI registers location and length + - interrupts : should contain the OHCI interrupt + +1.h) The Enhanced Host Controller Interface (EHCI) node + + Represents the USB 2.0 Enhanced Host Controller Interface. + + Required properties: + + - compatible : should be "nintendo,hollywood-usb-ehci","usb-ehci" + - reg : should contain the EHCI registers location and length + - interrupts : should contain the EHCI interrupt + +1.i) The Secure Digital Host Controller Interface (SDHCI) nodes + + Represent the Secure Digital Host Controller Interfaces. + + Required properties: + + - compatible : should be "nintendo,hollywood-sdhci","sdhci" + - reg : should contain the SDHCI registers location and length + - interrupts : should contain the SDHCI interrupt + +1.j) The Inter-Processor Communication (IPC) node + + Represent the Inter-Processor Communication interface. This interface + enables communications between the Broadway and the Starlet processors. + + - compatible : should be "nintendo,hollywood-ipc" + - reg : should contain the IPC registers location and length + - interrupts : should contain the IPC interrupt + +1.k) The "Hollywood" interrupt controller node + + Represents the "Hollywood" interrupt controller within the + "Hollywood" chip. + + Required properties: + + - #interrupt-cells : <1> + - compatible : should be "nintendo,hollywood-pic" + - reg : should contain the controller registers location and length + - interrupt-controller + - interrupts : should contain the cascade interrupt of the "flipper" pic + - interrupt-parent: should contain the phandle of the "flipper" pic + +1.l) The General Purpose I/O (GPIO) controller node + + Represents the dual access 32 GPIO controller interface. + + Required properties: + + - #gpio-cells : <2> + - compatible : should be "nintendo,hollywood-gpio" + - reg : should contain the IPC registers location and length + - gpio-controller + +1.m) The control node + + Represents the control interface used to setup several miscellaneous + settings of the "Hollywood" chip like boot memory mappings, resets, + disk interface mode, etc. + + Required properties: + + - compatible : should be "nintendo,hollywood-control" + - reg : should contain the control registers location and length + +1.n) The Disk Interface (DI) node + + Represents the interface used to communicate with mass storage devices. + + Required properties: + + - compatible : should be "nintendo,hollywood-di" + - reg : should contain the DI registers location and length + - interrupts : should contain the DI interrupt + diff --git a/Documentation/devicetree/bindings/regulator/anatop-regulator.txt b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt new file mode 100644 index 00000000..357758cb --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt @@ -0,0 +1,29 @@ +Anatop Voltage regulators + +Required properties: +- compatible: Must be "fsl,anatop-regulator" +- anatop-reg-offset: Anatop MFD register offset +- anatop-vol-bit-shift: Bit shift for the register +- anatop-vol-bit-width: Number of bits used in the register +- anatop-min-bit-val: Minimum value of this register +- anatop-min-voltage: Minimum voltage of this regulator +- anatop-max-voltage: Maximum voltage of this regulator + +Any property defined as part of the core regulator +binding, defined in regulator.txt, can also be used. + +Example: + + regulator-vddpu { + compatible = "fsl,anatop-regulator"; + regulator-name = "vddpu"; + regulator-min-microvolt = <725000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + anatop-reg-offset = <0x140>; + anatop-vol-bit-shift = <9>; + anatop-vol-bit-width = <5>; + anatop-min-bit-val = <1>; + anatop-min-voltage = <725000>; + anatop-max-voltage = <1300000>; + }; diff --git a/Documentation/devicetree/bindings/regulator/fixed-regulator.txt b/Documentation/devicetree/bindings/regulator/fixed-regulator.txt new file mode 100644 index 00000000..9cf57fd0 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/fixed-regulator.txt @@ -0,0 +1,29 @@ +Fixed Voltage regulators + +Required properties: +- compatible: Must be "regulator-fixed"; + +Optional properties: +- gpio: gpio to use for enable control +- startup-delay-us: startup time in microseconds +- enable-active-high: Polarity of GPIO is Active high +If this property is missing, the default assumed is Active low. + +Any property defined as part of the core regulator +binding, defined in regulator.txt, can also be used. +However a fixed voltage regulator is expected to have the +regulator-min-microvolt and regulator-max-microvolt +to be the same. + +Example: + + abc: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "fixed-supply"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio1 16 0>; + startup-delay-us = <70000>; + enable-active-high; + regulator-boot-on + }; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt new file mode 100644 index 00000000..5b7a408a --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -0,0 +1,54 @@ +Voltage/Current Regulators + +Optional properties: +- regulator-name: A string used as a descriptive name for regulator outputs +- regulator-min-microvolt: smallest voltage consumers may set +- regulator-max-microvolt: largest voltage consumers may set +- regulator-microvolt-offset: Offset applied to voltages to compensate for voltage drops +- regulator-min-microamp: smallest current consumers may set +- regulator-max-microamp: largest current consumers may set +- regulator-always-on: boolean, regulator should never be disabled +- regulator-boot-on: bootloader/firmware enabled regulator +- <name>-supply: phandle to the parent supply/regulator node + +Example: + + xyzreg: regulator@0 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + vin-supply = <&vin>; + }; + +Regulator Consumers: +Consumer nodes can reference one or more of its supplies/ +regulators using the below bindings. + +- <name>-supply: phandle to the regulator node + +These are the same bindings that a regulator in the above +example used to reference its own supply, in which case +its just seen as a special case of a regulator being a +consumer itself. + +Example of a consumer device node (mmc) referencing two +regulators (twl_reg1 and twl_reg2), + + twl_reg1: regulator@0 { + ... + ... + ... + }; + + twl_reg2: regulator@1 { + ... + ... + ... + }; + + mmc: mmc@0x0 { + ... + ... + vmmc-supply = <&twl_reg1>; + vmmcaux-supply = <&twl_reg2>; + }; diff --git a/Documentation/devicetree/bindings/regulator/twl-regulator.txt b/Documentation/devicetree/bindings/regulator/twl-regulator.txt new file mode 100644 index 00000000..0c3395d5 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/twl-regulator.txt @@ -0,0 +1,68 @@ +TWL family of regulators + +Required properties: +For twl6030 regulators/LDOs +- compatible: + - "ti,twl6030-vaux1" for VAUX1 LDO + - "ti,twl6030-vaux2" for VAUX2 LDO + - "ti,twl6030-vaux3" for VAUX3 LDO + - "ti,twl6030-vmmc" for VMMC LDO + - "ti,twl6030-vpp" for VPP LDO + - "ti,twl6030-vusim" for VUSIM LDO + - "ti,twl6030-vana" for VANA LDO + - "ti,twl6030-vcxio" for VCXIO LDO + - "ti,twl6030-vdac" for VDAC LDO + - "ti,twl6030-vusb" for VUSB LDO + - "ti,twl6030-v1v8" for V1V8 LDO + - "ti,twl6030-v2v1" for V2V1 LDO + - "ti,twl6030-clk32kg" for CLK32KG RESOURCE + - "ti,twl6030-vdd1" for VDD1 SMPS + - "ti,twl6030-vdd2" for VDD2 SMPS + - "ti,twl6030-vdd3" for VDD3 SMPS +For twl6025 regulators/LDOs +- compatible: + - "ti,twl6025-ldo1" for LDO1 LDO + - "ti,twl6025-ldo2" for LDO2 LDO + - "ti,twl6025-ldo3" for LDO3 LDO + - "ti,twl6025-ldo4" for LDO4 LDO + - "ti,twl6025-ldo5" for LDO5 LDO + - "ti,twl6025-ldo6" for LDO6 LDO + - "ti,twl6025-ldo7" for LDO7 LDO + - "ti,twl6025-ldoln" for LDOLN LDO + - "ti,twl6025-ldousb" for LDOUSB LDO + - "ti,twl6025-smps3" for SMPS3 SMPS + - "ti,twl6025-smps4" for SMPS4 SMPS + - "ti,twl6025-vio" for VIO SMPS +For twl4030 regulators/LDOs +- compatible: + - "ti,twl4030-vaux1" for VAUX1 LDO + - "ti,twl4030-vaux2" for VAUX2 LDO + - "ti,twl5030-vaux2" for VAUX2 LDO + - "ti,twl4030-vaux3" for VAUX3 LDO + - "ti,twl4030-vaux4" for VAUX4 LDO + - "ti,twl4030-vmmc1" for VMMC1 LDO + - "ti,twl4030-vmmc2" for VMMC2 LDO + - "ti,twl4030-vpll1" for VPLL1 LDO + - "ti,twl4030-vpll2" for VPLL2 LDO + - "ti,twl4030-vsim" for VSIM LDO + - "ti,twl4030-vdac" for VDAC LDO + - "ti,twl4030-vintana2" for VINTANA2 LDO + - "ti,twl4030-vio" for VIO LDO + - "ti,twl4030-vdd1" for VDD1 SMPS + - "ti,twl4030-vdd2" for VDD2 SMPS + - "ti,twl4030-vintana1" for VINTANA1 LDO + - "ti,twl4030-vintdig" for VINTDIG LDO + - "ti,twl4030-vusb1v5" for VUSB1V5 LDO + - "ti,twl4030-vusb1v8" for VUSB1V8 LDO + - "ti,twl4030-vusb3v1" for VUSB3V1 LDO + +Optional properties: +- Any optional property defined in bindings/regulator/regulator.txt + +Example: + + xyz: regulator@0 { + compatible = "ti,twl6030-vaux1"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + }; diff --git a/Documentation/devicetree/bindings/resource-names.txt b/Documentation/devicetree/bindings/resource-names.txt new file mode 100644 index 00000000..e280fef6 --- /dev/null +++ b/Documentation/devicetree/bindings/resource-names.txt @@ -0,0 +1,54 @@ +Some properties contain an ordered list of 1 or more datum which are +normally accessed by index. However, some devices will have multiple +values which are more naturally accessed by name. Device nodes can +include a supplemental property for assigning names to each of the list +items. The names property consists of a list of strings in the same +order as the data in the resource property. + +The following supplemental names properties are defined. + +Resource Property Supplemental Names Property +----------------- --------------------------- +reg reg-names +clocks clock-names +interrupts interrupt-names + +Usage: + +The -names property must be used in conjunction with the normal resource +property. If not it will be ignored. + +Examples: + +l4-abe { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x48000000 0x00001000>, /* MPU path */ + <1 0 0x49000000 0x00001000>; /* L3 path */ + mcasp { + compatible = "ti,mcasp"; + reg = <0 0x10 0x10>, <0 0x20 0x10>, + <1 0x10 0x10>, <1 0x20 0x10>; + reg-names = "mpu", "dat", + "dma", "dma_dat"; + interrupts = <11>, <12>; + interrupt-names = "rx", "tx"; + }; + + timer { + compatible = "ti,timer"; + reg = <0 0x40 0x10>, <1 0x40 0x10>; + reg-names = "mpu", "dma"; + }; +}; + + +usb { + compatible = "ti,usb-host"; + reg = <0x4a064000 0x800>, <0x4a064800 0x200>, + <0x4a064c00 0x200>; + reg-names = "config", "ohci", "ehci"; + interrupts = <14>, <15>; + interrupt-names = "ohci", "ehci"; +}; diff --git a/Documentation/devicetree/bindings/rtc/olpc-xo1-rtc.txt b/Documentation/devicetree/bindings/rtc/olpc-xo1-rtc.txt new file mode 100644 index 00000000..a2891ceb --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/olpc-xo1-rtc.txt @@ -0,0 +1,5 @@ +OLPC XO-1 RTC +~~~~~~~~~~~~~ + +Required properties: + - compatible : "olpc,xo1-rtc" diff --git a/Documentation/devicetree/bindings/rtc/rtc-cmos.txt b/Documentation/devicetree/bindings/rtc/rtc-cmos.txt new file mode 100644 index 00000000..7382989b --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/rtc-cmos.txt @@ -0,0 +1,28 @@ + Motorola mc146818 compatible RTC +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +Required properties: + - compatible : "motorola,mc146818" + - reg : should contain registers location and length. + +Optional properties: + - interrupts : should contain interrupt. + - interrupt-parent : interrupt source phandle. + - ctrl-reg : Contains the initial value of the control register also + called "Register B". + - freq-reg : Contains the initial value of the frequency register also + called "Regsiter A". + +"Register A" and "B" are usually initialized by the firmware (BIOS for +instance). If this is not done, it can be performed by the driver. + +ISA Example: + + rtc@70 { + compatible = "motorola,mc146818"; + interrupts = <8 3>; + interrupt-parent = <&ioapic1>; + ctrl-reg = <2>; + freq-reg = <0x26>; + reg = <1 0x70 2>; + }; diff --git a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt new file mode 100644 index 00000000..90ec45fd --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt @@ -0,0 +1,20 @@ +* Samsung's S3C Real Time Clock controller + +Required properties: +- compatible: should be one of the following. + * "samsung,s3c2410-rtc" - for controllers compatible with s3c2410 rtc. + * "samsung,s3c6410-rtc" - for controllers compatible with s3c6410 rtc. +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: Two interrupt numbers to the cpu should be specified. First + interrupt number is the rtc alarm interupt and second interrupt number + is the rtc tick interrupt. The number of cells representing a interrupt + depends on the parent interrupt controller. + +Example: + + rtc@10070000 { + compatible = "samsung,s3c6410-rtc"; + reg = <0x10070000 0x100>; + interrupts = <44 0 45 0>; + }; diff --git a/Documentation/devicetree/bindings/rtc/sa1100-rtc.txt b/Documentation/devicetree/bindings/rtc/sa1100-rtc.txt new file mode 100644 index 00000000..0cda19ad --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/sa1100-rtc.txt @@ -0,0 +1,17 @@ +* Marvell Real Time Clock controller + +Required properties: +- compatible: should be "mrvl,sa1100-rtc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: Should be two. The first interrupt number is the rtc alarm + interrupt and the second interrupt number is the rtc hz interrupt. +- interrupt-names: Assign name of irq resource. + +Example: + rtc: rtc@d4010000 { + compatible = "mrvl,mmp-rtc"; + reg = <0xd4010000 0x1000>; + interrupts = <5>, <6>; + interrupt-name = "rtc 1Hz", "rtc alarm"; + }; diff --git a/Documentation/devicetree/bindings/rtc/twl-rtc.txt b/Documentation/devicetree/bindings/rtc/twl-rtc.txt new file mode 100644 index 00000000..596e0c97 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/twl-rtc.txt @@ -0,0 +1,12 @@ +* TI twl RTC + +The TWL family (twl4030/6030) contains a RTC. + +Required properties: +- compatible : Should be twl4030-rtc + +Examples: + +rtc@0 { + compatible = "ti,twl4030-rtc"; +}; diff --git a/Documentation/devicetree/bindings/serial/altera_jtaguart.txt b/Documentation/devicetree/bindings/serial/altera_jtaguart.txt new file mode 100644 index 00000000..c152f65f --- /dev/null +++ b/Documentation/devicetree/bindings/serial/altera_jtaguart.txt @@ -0,0 +1,4 @@ +Altera JTAG UART + +Required properties: +- compatible : should be "ALTR,juart-1.0" diff --git a/Documentation/devicetree/bindings/serial/altera_uart.txt b/Documentation/devicetree/bindings/serial/altera_uart.txt new file mode 100644 index 00000000..71cae3f7 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/altera_uart.txt @@ -0,0 +1,7 @@ +Altera UART + +Required properties: +- compatible : should be "ALTR,uart-1.0" + +Optional properties: +- clock-frequency : frequency of the clock input to the UART diff --git a/Documentation/devicetree/bindings/serial/mrvl-serial.txt b/Documentation/devicetree/bindings/serial/mrvl-serial.txt new file mode 100644 index 00000000..d744340d --- /dev/null +++ b/Documentation/devicetree/bindings/serial/mrvl-serial.txt @@ -0,0 +1,4 @@ +PXA UART controller + +Required properties: +- compatible : should be "mrvl,mmp-uart" or "mrvl,pxa-uart". diff --git a/Documentation/devicetree/bindings/serial/omap_serial.txt b/Documentation/devicetree/bindings/serial/omap_serial.txt new file mode 100644 index 00000000..342eedd1 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/omap_serial.txt @@ -0,0 +1,10 @@ +OMAP UART controller + +Required properties: +- compatible : should be "ti,omap2-uart" for OMAP2 controllers +- compatible : should be "ti,omap3-uart" for OMAP3 controllers +- compatible : should be "ti,omap4-uart" for OMAP4 controllers +- ti,hwmods : Must be "uart<n>", n being the instance number (1-based) + +Optional properties: +- clock-frequency : frequency of the clock input to the UART diff --git a/Documentation/devicetree/bindings/serial/rs485.txt b/Documentation/devicetree/bindings/serial/rs485.txt new file mode 100644 index 00000000..1e753c69 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/rs485.txt @@ -0,0 +1,31 @@ +* RS485 serial communications + +The RTS signal is capable of automatically controlling line direction for +the built-in half-duplex mode. +The properties described hereafter shall be given to a half-duplex capable +UART node. + +Required properties: +- rs485-rts-delay: prop-encoded-array <a b> where: + * a is the delay beteween rts signal and beginning of data sent in milliseconds. + it corresponds to the delay before sending data. + * b is the delay between end of data sent and rts signal in milliseconds + it corresponds to the delay after sending data and actual release of the line. + +Optional properties: +- linux,rs485-enabled-at-boot-time: empty property telling to enable the rs485 + feature at boot time. It can be disabled later with proper ioctl. +- rs485-rx-during-tx: empty property that enables the receiving of data even + whilst sending data. + +RS485 example for Atmel USART: + usart0: serial@fff8c000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfff8c000 0x4000>; + interrupts = <7>; + atmel,use-dma-rx; + atmel,use-dma-tx; + linux,rs485-enabled-at-boot-time; + rs485-rts-delay = <0 200>; // in milliseconds + }; + diff --git a/Documentation/devicetree/bindings/serial/samsung_uart.txt b/Documentation/devicetree/bindings/serial/samsung_uart.txt new file mode 100644 index 00000000..2c8a17cf --- /dev/null +++ b/Documentation/devicetree/bindings/serial/samsung_uart.txt @@ -0,0 +1,14 @@ +* Samsung's UART Controller + +The Samsung's UART controller is used for interfacing SoC with serial communicaion +devices. + +Required properties: +- compatible: should be + - "samsung,exynos4210-uart", for UART's compatible with Exynos4210 uart ports. + +- reg: base physical address of the controller and length of memory mapped + region. + +- interrupts: interrupt number to the cpu. The interrupt specifier format depends + on the interrupt controller parent. diff --git a/Documentation/devicetree/bindings/serio/altera_ps2.txt b/Documentation/devicetree/bindings/serio/altera_ps2.txt new file mode 100644 index 00000000..4d9eecc2 --- /dev/null +++ b/Documentation/devicetree/bindings/serio/altera_ps2.txt @@ -0,0 +1,4 @@ +Altera UP PS/2 controller + +Required properties: +- compatible : should be "ALTR,ps2-1.0". diff --git a/Documentation/devicetree/bindings/sound/alc5632.txt b/Documentation/devicetree/bindings/sound/alc5632.txt new file mode 100644 index 00000000..8608f747 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/alc5632.txt @@ -0,0 +1,24 @@ +ALC5632 audio CODEC + +This device supports I2C only. + +Required properties: + + - compatible : "realtek,alc5632" + + - reg : the I2C address of the device. + + - gpio-controller : Indicates this device is a GPIO controller. + + - #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). + +Example: + +alc5632: alc5632@1e { + compatible = "realtek,alc5632"; + reg = <0x1a>; + + gpio-controller; + #gpio-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/sound/imx-audmux.txt b/Documentation/devicetree/bindings/sound/imx-audmux.txt new file mode 100644 index 00000000..215aa981 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/imx-audmux.txt @@ -0,0 +1,13 @@ +Freescale Digital Audio Mux (AUDMUX) device + +Required properties: +- compatible : "fsl,imx21-audmux" for AUDMUX version firstly used on i.MX21, + or "fsl,imx31-audmux" for the version firstly used on i.MX31. +- reg : Should contain AUDMUX registers location and length + +Example: + +audmux@021d8000 { + compatible = "fsl,imx6q-audmux", "fsl,imx31-audmux"; + reg = <0x021d8000 0x4000>; +}; diff --git a/Documentation/devicetree/bindings/sound/sgtl5000.txt b/Documentation/devicetree/bindings/sound/sgtl5000.txt new file mode 100644 index 00000000..9cc44449 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/sgtl5000.txt @@ -0,0 +1,13 @@ +* Freescale SGTL5000 Stereo Codec + +Required properties: +- compatible : "fsl,sgtl5000". + +- reg : the I2C address of the device + +Example: + +codec: sgtl5000@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; +}; diff --git a/Documentation/devicetree/bindings/sound/tegra-audio-alc5632.txt b/Documentation/devicetree/bindings/sound/tegra-audio-alc5632.txt new file mode 100644 index 00000000..b77a97c9 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tegra-audio-alc5632.txt @@ -0,0 +1,59 @@ +NVIDIA Tegra audio complex + +Required properties: +- compatible : "nvidia,tegra-audio-alc5632" +- nvidia,model : The user-visible name of this sound complex. +- nvidia,audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names for sources and + sinks are the ALC5632's pins: + + ALC5632 pins: + + * SPK_OUTP + * SPK_OUTN + * HP_OUT_L + * HP_OUT_R + * AUX_OUT_P + * AUX_OUT_N + * LINE_IN_L + * LINE_IN_R + * PHONE_P + * PHONE_N + * MIC1_P + * MIC1_N + * MIC2_P + * MIC2_N + * MICBIAS1 + * DMICDAT + + Board connectors: + + * Headset Stereophone + * Int Spk + * Headset Mic + * Digital Mic + +- nvidia,i2s-controller : The phandle of the Tegra I2S controller +- nvidia,audio-codec : The phandle of the ALC5632 audio codec + +Example: + +sound { + compatible = "nvidia,tegra-audio-alc5632-paz00", + "nvidia,tegra-audio-alc5632"; + + nvidia,model = "Compal PAZ00"; + + nvidia,audio-routing = + "Int Spk", "SPK_OUTP", + "Int Spk", "SPK_OUTN", + "Headset Mic","MICBIAS1", + "MIC1_N", "Headset Mic", + "MIC1_P", "Headset Mic", + "Headset Stereophone", "HP_OUT_R", + "Headset Stereophone", "HP_OUT_L"; + + nvidia,i2s-controller = <&tegra_i2s1>; + nvidia,audio-codec = <&alc5632>; +}; diff --git a/Documentation/devicetree/bindings/sound/tegra-audio-wm8903.txt b/Documentation/devicetree/bindings/sound/tegra-audio-wm8903.txt new file mode 100644 index 00000000..d5b0da8b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tegra-audio-wm8903.txt @@ -0,0 +1,71 @@ +NVIDIA Tegra audio complex + +Required properties: +- compatible : "nvidia,tegra-audio-wm8903" +- nvidia,model : The user-visible name of this sound complex. +- nvidia,audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names for sources and + sinks are the WM8903's pins, and the jacks on the board: + + WM8903 pins: + + * IN1L + * IN1R + * IN2L + * IN2R + * IN3L + * IN3R + * DMICDAT + * HPOUTL + * HPOUTR + * LINEOUTL + * LINEOUTR + * LOP + * LON + * ROP + * RON + * MICBIAS + + Board connectors: + + * Headphone Jack + * Int Spk + * Mic Jack + +- nvidia,i2s-controller : The phandle of the Tegra I2S1 controller +- nvidia,audio-codec : The phandle of the WM8903 audio codec + +Optional properties: +- nvidia,spkr-en-gpios : The GPIO that enables the speakers +- nvidia,hp-mute-gpios : The GPIO that mutes the headphones +- nvidia,hp-det-gpios : The GPIO that detect headphones are plugged in +- nvidia,int-mic-en-gpios : The GPIO that enables the internal microphone +- nvidia,ext-mic-en-gpios : The GPIO that enables the external microphone + +Example: + +sound { + compatible = "nvidia,tegra-audio-wm8903-harmony", + "nvidia,tegra-audio-wm8903" + nvidia,model = "tegra-wm8903-harmony"; + + nvidia,audio-routing = + "Headphone Jack", "HPOUTR", + "Headphone Jack", "HPOUTL", + "Int Spk", "ROP", + "Int Spk", "RON", + "Int Spk", "LOP", + "Int Spk", "LON", + "Mic Jack", "MICBIAS", + "IN1L", "Mic Jack"; + + nvidia,i2s-controller = <&i2s1>; + nvidia,audio-codec = <&wm8903>; + + nvidia,spkr-en-gpios = <&codec 2 0>; + nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */ + nvidia,int-mic-en-gpios = <&gpio 184 0>; /*gpio PX0 */ + nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */ +}; + diff --git a/Documentation/devicetree/bindings/sound/tegra20-das.txt b/Documentation/devicetree/bindings/sound/tegra20-das.txt new file mode 100644 index 00000000..6de3a7ee --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tegra20-das.txt @@ -0,0 +1,12 @@ +NVIDIA Tegra 20 DAS (Digital Audio Switch) controller + +Required properties: +- compatible : "nvidia,tegra20-das" +- reg : Should contain DAS registers location and length + +Example: + +das@70000c00 { + compatible = "nvidia,tegra20-das"; + reg = <0x70000c00 0x80>; +}; diff --git a/Documentation/devicetree/bindings/sound/tegra20-i2s.txt b/Documentation/devicetree/bindings/sound/tegra20-i2s.txt new file mode 100644 index 00000000..0df2b5c8 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tegra20-i2s.txt @@ -0,0 +1,17 @@ +NVIDIA Tegra 20 I2S controller + +Required properties: +- compatible : "nvidia,tegra20-i2s" +- reg : Should contain I2S registers location and length +- interrupts : Should contain I2S interrupt +- nvidia,dma-request-selector : The Tegra DMA controller's phandle and + request selector for this I2S controller + +Example: + +i2s@70002800 { + compatible = "nvidia,tegra20-i2s"; + reg = <0x70002800 0x200>; + interrupts = < 45 >; + nvidia,dma-request-selector = < &apbdma 2 >; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8510.txt b/Documentation/devicetree/bindings/sound/wm8510.txt new file mode 100644 index 00000000..fa1a32b8 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8510.txt @@ -0,0 +1,18 @@ +WM8510 audio CODEC + +This device supports both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "wlf,wm8510" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Example: + +codec: wm8510@1a { + compatible = "wlf,wm8510"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8523.txt b/Documentation/devicetree/bindings/sound/wm8523.txt new file mode 100644 index 00000000..04746186 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8523.txt @@ -0,0 +1,16 @@ +WM8523 audio CODEC + +This device supports I2C only. + +Required properties: + + - compatible : "wlf,wm8523" + + - reg : the I2C address of the device. + +Example: + +codec: wm8523@1a { + compatible = "wlf,wm8523"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8580.txt b/Documentation/devicetree/bindings/sound/wm8580.txt new file mode 100644 index 00000000..7d9821f3 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8580.txt @@ -0,0 +1,16 @@ +WM8580 audio CODEC + +This device supports I2C only. + +Required properties: + + - compatible : "wlf,wm8580" + + - reg : the I2C address of the device. + +Example: + +codec: wm8580@1a { + compatible = "wlf,wm8580"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8711.txt b/Documentation/devicetree/bindings/sound/wm8711.txt new file mode 100644 index 00000000..8ed9998c --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8711.txt @@ -0,0 +1,18 @@ +WM8711 audio CODEC + +This device supports both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "wlf,wm8711" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Example: + +codec: wm8711@1a { + compatible = "wlf,wm8711"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8728.txt b/Documentation/devicetree/bindings/sound/wm8728.txt new file mode 100644 index 00000000..a8b5c366 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8728.txt @@ -0,0 +1,18 @@ +WM8728 audio CODEC + +This device supports both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "wlf,wm8728" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Example: + +codec: wm8728@1a { + compatible = "wlf,wm8728"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8731.txt b/Documentation/devicetree/bindings/sound/wm8731.txt new file mode 100644 index 00000000..15f70048 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8731.txt @@ -0,0 +1,18 @@ +WM8731 audio CODEC + +This device supports both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "wlf,wm8731" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Example: + +codec: wm8731@1a { + compatible = "wlf,wm8731"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8737.txt b/Documentation/devicetree/bindings/sound/wm8737.txt new file mode 100644 index 00000000..4bc2cea3 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8737.txt @@ -0,0 +1,18 @@ +WM8737 audio CODEC + +This device supports both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "wlf,wm8737" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Example: + +codec: wm8737@1a { + compatible = "wlf,wm8737"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8741.txt b/Documentation/devicetree/bindings/sound/wm8741.txt new file mode 100644 index 00000000..74bda58c --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8741.txt @@ -0,0 +1,18 @@ +WM8741 audio CODEC + +This device supports both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "wlf,wm8741" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Example: + +codec: wm8741@1a { + compatible = "wlf,wm8741"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8750.txt b/Documentation/devicetree/bindings/sound/wm8750.txt new file mode 100644 index 00000000..8db239fd --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8750.txt @@ -0,0 +1,18 @@ +WM8750 and WM8987 audio CODECs + +These devices support both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "wlf,wm8750" or "wlf,wm8987" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Example: + +codec: wm8750@1a { + compatible = "wlf,wm8750"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8753.txt b/Documentation/devicetree/bindings/sound/wm8753.txt new file mode 100644 index 00000000..e65277a0 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8753.txt @@ -0,0 +1,18 @@ +WM8753 audio CODEC + +This device supports both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "wlf,wm8753" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Example: + +codec: wm8737@1a { + compatible = "wlf,wm8753"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8770.txt b/Documentation/devicetree/bindings/sound/wm8770.txt new file mode 100644 index 00000000..866e00ca --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8770.txt @@ -0,0 +1,16 @@ +WM8770 audio CODEC + +This device supports SPI. + +Required properties: + + - compatible : "wlf,wm8770" + + - reg : the chip select number. + +Example: + +codec: wm8770@1 { + compatible = "wlf,wm8770"; + reg = <1>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8776.txt b/Documentation/devicetree/bindings/sound/wm8776.txt new file mode 100644 index 00000000..3b9ca49a --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8776.txt @@ -0,0 +1,18 @@ +WM8776 audio CODEC + +This device supports both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "wlf,wm8776" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Example: + +codec: wm8776@1a { + compatible = "wlf,wm8776"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8804.txt b/Documentation/devicetree/bindings/sound/wm8804.txt new file mode 100644 index 00000000..4d3a56f3 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8804.txt @@ -0,0 +1,18 @@ +WM8804 audio CODEC + +This device supports both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "wlf,wm8804" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Example: + +codec: wm8804@1a { + compatible = "wlf,wm8804"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8903.txt b/Documentation/devicetree/bindings/sound/wm8903.txt new file mode 100644 index 00000000..f102cbc4 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8903.txt @@ -0,0 +1,50 @@ +WM8903 audio CODEC + +This device supports I2C only. + +Required properties: + + - compatible : "wlf,wm8903" + + - reg : the I2C address of the device. + + - gpio-controller : Indicates this device is a GPIO controller. + + - #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). + +Optional properties: + + - interrupts : The interrupt line the codec is connected to. + + - micdet-cfg : Default register value for R6 (Mic Bias). If absent, the + default is 0. + + - micdet-delay : The debounce delay for microphone detection in mS. If + absent, the default is 100. + + - gpio-cfg : A list of GPIO configuration register values. The list must + be 5 entries long. If absent, no configuration of these registers is + performed. If any entry has the value 0xffffffff, that GPIO's + configuration will not be modified. + +Example: + +codec: wm8903@1a { + compatible = "wlf,wm8903"; + reg = <0x1a>; + interrupts = < 347 >; + + gpio-controller; + #gpio-cells = <2>; + + micdet-cfg = <0>; + micdet-delay = <100>; + gpio-cfg = < + 0x0600 /* DMIC_LR, output */ + 0x0680 /* DMIC_DAT, input */ + 0x0000 /* GPIO, output, low */ + 0x0200 /* Interrupt, output */ + 0x01a0 /* BCLK, input, active high */ + >; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8994.txt b/Documentation/devicetree/bindings/sound/wm8994.txt new file mode 100644 index 00000000..7a7eb1e7 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8994.txt @@ -0,0 +1,18 @@ +WM1811/WM8994/WM8958 audio CODEC + +These devices support both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "wlf,wm1811", "wlf,wm8994", "wlf,wm8958" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Example: + +codec: wm8994@1a { + compatible = "wlf,wm8994"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt new file mode 100644 index 00000000..9841057d --- /dev/null +++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt @@ -0,0 +1,22 @@ +* Freescale (Enhanced) Configurable Serial Peripheral Interface + (CSPI/eCSPI) for i.MX + +Required properties: +- compatible : Should be "fsl,<soc>-cspi" or "fsl,<soc>-ecspi" +- reg : Offset and length of the register set for the device +- interrupts : Should contain CSPI/eCSPI interrupt +- fsl,spi-num-chipselects : Contains the number of the chipselect +- cs-gpios : Specifies the gpio pins to be used for chipselects. + +Example: + +ecspi@70010000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx51-ecspi"; + reg = <0x70010000 0x4000>; + interrupts = <36>; + fsl,spi-num-chipselects = <2>; + cs-gpios = <&gpio3 24 0>, /* GPIO4_24 */ + <&gpio3 25 0>; /* GPIO4_25 */ +}; diff --git a/Documentation/devicetree/bindings/spi/fsl-spi.txt b/Documentation/devicetree/bindings/spi/fsl-spi.txt new file mode 100644 index 00000000..777abd73 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/fsl-spi.txt @@ -0,0 +1,53 @@ +* SPI (Serial Peripheral Interface) + +Required properties: +- cell-index : QE SPI subblock index. + 0: QE subblock SPI1 + 1: QE subblock SPI2 +- compatible : should be "fsl,spi". +- mode : the SPI operation mode, it can be "cpu" or "cpu-qe". +- reg : Offset and length of the register set for the device +- interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Optional properties: +- gpios : specifies the gpio pins to be used for chipselects. + The gpios will be referred to as reg = <index> in the SPI child nodes. + If unspecified, a single SPI device without a chip select can be used. + +Example: + spi@4c0 { + cell-index = <0>; + compatible = "fsl,spi"; + reg = <4c0 40>; + interrupts = <82 0>; + interrupt-parent = <700>; + mode = "cpu"; + gpios = <&gpio 18 1 // device reg=<0> + &gpio 19 1>; // device reg=<1> + }; + + +* eSPI (Enhanced Serial Peripheral Interface) + +Required properties: +- compatible : should be "fsl,mpc8536-espi". +- reg : Offset and length of the register set for the device. +- interrupts : should contain eSPI interrupt, the device has one interrupt. +- fsl,espi-num-chipselects : the number of the chipselect signals. + +Example: + spi@110000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc8536-espi"; + reg = <0x110000 0x1000>; + interrupts = <53 0x2>; + interrupt-parent = <&mpic>; + fsl,espi-num-chipselects = <4>; + }; diff --git a/Documentation/devicetree/bindings/spi/omap-spi.txt b/Documentation/devicetree/bindings/spi/omap-spi.txt new file mode 100644 index 00000000..81df374a --- /dev/null +++ b/Documentation/devicetree/bindings/spi/omap-spi.txt @@ -0,0 +1,20 @@ +OMAP2+ McSPI device + +Required properties: +- compatible : + - "ti,omap2-spi" for OMAP2 & OMAP3. + - "ti,omap4-spi" for OMAP4+. +- ti,spi-num-cs : Number of chipselect supported by the instance. +- ti,hwmods: Name of the hwmod associated to the McSPI + + +Example: + +mcspi1: mcspi@1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,omap4-mcspi"; + ti,hwmods = "mcspi1"; + ti,spi-num-cs = <4>; +}; + diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt new file mode 100644 index 00000000..e782add2 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -0,0 +1,57 @@ +SPI (Serial Peripheral Interface) busses + +SPI busses can be described with a node for the SPI master device +and a set of child nodes for each SPI slave on the bus. For this +discussion, it is assumed that the system's SPI controller is in +SPI master mode. This binding does not describe SPI controllers +in slave mode. + +The SPI master node requires the following properties: +- #address-cells - number of cells required to define a chip select + address on the SPI bus. +- #size-cells - should be zero. +- compatible - name of SPI bus controller following generic names + recommended practice. +No other properties are required in the SPI bus node. It is assumed +that a driver for an SPI bus device will understand that it is an SPI bus. +However, the binding does not attempt to define the specific method for +assigning chip select numbers. Since SPI chip select configuration is +flexible and non-standardized, it is left out of this binding with the +assumption that board specific platform code will be used to manage +chip selects. Individual drivers can define additional properties to +support describing the chip select layout. + +SPI slave nodes must be children of the SPI master node and can +contain the following properties. +- reg - (required) chip select address of device. +- compatible - (required) name of SPI device following generic names + recommended practice +- spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz +- spi-cpol - (optional) Empty property indicating device requires + inverse clock polarity (CPOL) mode +- spi-cpha - (optional) Empty property indicating device requires + shifted clock phase (CPHA) mode +- spi-cs-high - (optional) Empty property indicating device requires + chip select active high + +SPI example for an MPC5200 SPI bus: + spi@f00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; + reg = <0xf00 0x20>; + interrupts = <2 13 0 2 14 0>; + interrupt-parent = <&mpc5200_pic>; + + ethernet-switch@0 { + compatible = "micrel,ks8995m"; + spi-max-frequency = <1000000>; + reg = <0>; + }; + + codec@1 { + compatible = "ti,tlv320aic26"; + spi-max-frequency = <100000>; + reg = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/spi/spi_altera.txt b/Documentation/devicetree/bindings/spi/spi_altera.txt new file mode 100644 index 00000000..dda37594 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi_altera.txt @@ -0,0 +1,4 @@ +Altera SPI + +Required properties: +- compatible : should be "ALTR,spi-1.0". diff --git a/Documentation/devicetree/bindings/spi/spi_nvidia.txt b/Documentation/devicetree/bindings/spi/spi_nvidia.txt new file mode 100644 index 00000000..6b9e5189 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi_nvidia.txt @@ -0,0 +1,5 @@ +NVIDIA Tegra 2 SPI device + +Required properties: +- compatible : should be "nvidia,tegra20-spi". +- gpios : should specify GPIOs used for chipselect. diff --git a/Documentation/devicetree/bindings/spi/spi_oc_tiny.txt b/Documentation/devicetree/bindings/spi/spi_oc_tiny.txt new file mode 100644 index 00000000..d95c0b36 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi_oc_tiny.txt @@ -0,0 +1,12 @@ +OpenCores tiny SPI + +Required properties: +- compatible : should be "opencores,tiny-spi-rtlsvn2". +- gpios : should specify GPIOs used for chipselect. +Optional properties: +- clock-frequency : input clock frequency to the core. +- baud-width: width, in bits, of the programmable divider used to scale + the input clock to SCLK. + +The clock-frequency and baud-width properties are needed only if the divider +is programmable. They are not needed if the divider is fixed. diff --git a/Documentation/devicetree/bindings/spi/spi_pl022.txt b/Documentation/devicetree/bindings/spi/spi_pl022.txt new file mode 100644 index 00000000..306ec3ff --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi_pl022.txt @@ -0,0 +1,12 @@ +ARM PL022 SPI controller + +Required properties: +- compatible : "arm,pl022", "arm,primecell" +- reg : Offset and length of the register set for the device +- interrupts : Should contain SPI controller interrupt + +Optional properties: +- cs-gpios : should specify GPIOs used for chipselects. + The gpios will be referred to as reg = <index> in the SPI child nodes. + If unspecified, a single SPI device without a chip select can be used. + diff --git a/Documentation/devicetree/bindings/tty/serial/atmel-usart.txt b/Documentation/devicetree/bindings/tty/serial/atmel-usart.txt new file mode 100644 index 00000000..a49d9a1d --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/atmel-usart.txt @@ -0,0 +1,27 @@ +* Atmel Universal Synchronous Asynchronous Receiver/Transmitter (USART) + +Required properties: +- compatible: Should be "atmel,<chip>-usart" + The compatible <chip> indicated will be the first SoC to support an + additional mode or an USART new feature. +- reg: Should contain registers location and length +- interrupts: Should contain interrupt + +Optional properties: +- atmel,use-dma-rx: use of PDC or DMA for receiving data +- atmel,use-dma-tx: use of PDC or DMA for transmitting data + +<chip> compatible description: +- at91rm9200: legacy USART support +- at91sam9260: generic USART implementation for SAM9 SoCs + +Example: + + usart0: serial@fff8c000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfff8c000 0x4000>; + interrupts = <7>; + atmel,use-dma-rx; + atmel,use-dma-tx; + }; + diff --git a/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt b/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt new file mode 100644 index 00000000..6588b695 --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt @@ -0,0 +1,14 @@ +* Energymicro efm32 UART + +Required properties: +- compatible : Should be "efm32,uart" +- reg : Address and length of the register set +- interrupts : Should contain uart interrupt + +Example: + +uart@0x4000c400 { + compatible = "efm32,uart"; + reg = <0x4000c400 0x400>; + interrupts = <15>; +}; diff --git a/Documentation/devicetree/bindings/tty/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/tty/serial/fsl-imx-uart.txt new file mode 100644 index 00000000..a9c04062 --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/fsl-imx-uart.txt @@ -0,0 +1,19 @@ +* Freescale i.MX Universal Asynchronous Receiver/Transmitter (UART) + +Required properties: +- compatible : Should be "fsl,<soc>-uart" +- reg : Address and length of the register set for the device +- interrupts : Should contain uart interrupt + +Optional properties: +- fsl,uart-has-rtscts : Indicate the uart has rts and cts +- fsl,irda-mode : Indicate the uart supports irda mode + +Example: + +uart@73fbc000 { + compatible = "fsl,imx51-uart", "fsl,imx21-uart"; + reg = <0x73fbc000 0x4000>; + interrupts = <31>; + fsl,uart-has-rtscts; +}; diff --git a/Documentation/devicetree/bindings/tty/serial/msm_serial.txt b/Documentation/devicetree/bindings/tty/serial/msm_serial.txt new file mode 100644 index 00000000..aef383eb --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/msm_serial.txt @@ -0,0 +1,27 @@ +* Qualcomm MSM UART + +Required properties: +- compatible : + - "qcom,msm-uart", and one of "qcom,msm-hsuart" or + "qcom,msm-lsuart". +- reg : offset and length of the register set for the device + for the hsuart operating in compatible mode, there should be a + second pair describing the gsbi registers. +- interrupts : should contain the uart interrupt. + +There are two different UART blocks used in MSM devices, +"qcom,msm-hsuart" and "qcom,msm-lsuart". The msm-serial driver is +able to handle both of these, and matches against the "qcom,msm-uart" +as the compatibility. + +The registers for the "qcom,msm-hsuart" device need to specify both +register blocks, even for the common driver. + +Example: + + uart@19c400000 { + compatible = "qcom,msm-hsuart", "qcom,msm-uart"; + reg = <0x19c40000 0x1000>, + <0x19c00000 0x1000>; + interrupts = <195>; + }; diff --git a/Documentation/devicetree/bindings/tty/serial/of-serial.txt b/Documentation/devicetree/bindings/tty/serial/of-serial.txt new file mode 100644 index 00000000..b8b27b0a --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/of-serial.txt @@ -0,0 +1,36 @@ +* UART (Universal Asynchronous Receiver/Transmitter) + +Required properties: +- compatible : one of: + - "ns8250" + - "ns16450" + - "ns16550a" + - "ns16550" + - "ns16750" + - "ns16850" + - "nvidia,tegra20-uart" + - "ibm,qpace-nwp-serial" + - "serial" if the port type is unknown. +- reg : offset and length of the register set for the device. +- interrupts : should contain uart interrupt. +- clock-frequency : the input clock frequency for the UART. + +Optional properties: +- current-speed : the current active speed of the UART. +- reg-offset : offset to apply to the mapbase from the start of the registers. +- reg-shift : quantity to shift the register offsets by. +- reg-io-width : the size (in bytes) of the IO accesses that should be + performed on the device. There are some systems that require 32-bit + accesses to the UART (e.g. TI davinci). +- used-by-rtas : set to indicate that the port is in use by the OpenFirmware + RTAS and should not be registered. + +Example: + + uart@80230000 { + compatible = "ns8250"; + reg = <0x80230000 0x100>; + clock-frequency = <3686400>; + interrupts = <10>; + reg-shift = <2>; + }; diff --git a/Documentation/devicetree/bindings/tty/serial/snps-dw-apb-uart.txt b/Documentation/devicetree/bindings/tty/serial/snps-dw-apb-uart.txt new file mode 100644 index 00000000..f13f1c5b --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/snps-dw-apb-uart.txt @@ -0,0 +1,25 @@ +* Synopsys DesignWare ABP UART + +Required properties: +- compatible : "snps,dw-apb-uart" +- reg : offset and length of the register set for the device. +- interrupts : should contain uart interrupt. +- clock-frequency : the input clock frequency for the UART. + +Optional properties: +- reg-shift : quantity to shift the register offsets by. If this property is + not present then the register offsets are not shifted. +- reg-io-width : the size (in bytes) of the IO accesses that should be + performed on the device. If this property is not present then single byte + accesses are used. + +Example: + + uart@80230000 { + compatible = "snps,dw-apb-uart"; + reg = <0x80230000 0x100>; + clock-frequency = <3686400>; + interrupts = <10>; + reg-shift = <2>; + reg-io-width = <4>; + }; diff --git a/Documentation/devicetree/bindings/usb/atmel-usb.txt b/Documentation/devicetree/bindings/usb/atmel-usb.txt new file mode 100644 index 00000000..60bd2150 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/atmel-usb.txt @@ -0,0 +1,49 @@ +Atmel SOC USB controllers + +OHCI + +Required properties: + - compatible: Should be "atmel,at91rm9200-ohci" for USB controllers + used in host mode. + - num-ports: Number of ports. + - atmel,vbus-gpio: If present, specifies a gpio that needs to be + activated for the bus to be powered. + - atmel,oc-gpio: If present, specifies a gpio that needs to be + activated for the overcurrent detection. + +usb0: ohci@00500000 { + compatible = "atmel,at91rm9200-ohci", "usb-ohci"; + reg = <0x00500000 0x100000>; + interrupts = <20 4>; + num-ports = <2>; +}; + +EHCI + +Required properties: + - compatible: Should be "atmel,at91sam9g45-ehci" for USB controllers + used in host mode. + +usb1: ehci@00800000 { + compatible = "atmel,at91sam9g45-ehci", "usb-ehci"; + reg = <0x00800000 0x100000>; + interrupts = <22 4>; +}; + +AT91 USB device controller + +Required properties: + - compatible: Should be "atmel,at91rm9200-udc" + - reg: Address and length of the register set for the device + - interrupts: Should contain macb interrupt + +Optional properties: + - atmel,vbus-gpio: If present, specifies a gpio that needs to be + activated for the bus to be powered. + +usb1: gadget@fffa4000 { + compatible = "atmel,at91rm9200-udc"; + reg = <0xfffa4000 0x4000>; + interrupts = <10 4>; + atmel,vbus-gpio = <&pioC 5 0>; +}; diff --git a/Documentation/devicetree/bindings/usb/fsl-usb.txt b/Documentation/devicetree/bindings/usb/fsl-usb.txt new file mode 100644 index 00000000..bd5723f0 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/fsl-usb.txt @@ -0,0 +1,81 @@ +Freescale SOC USB controllers + +The device node for a USB controller that is part of a Freescale +SOC is as described in the document "Open Firmware Recommended +Practice : Universal Serial Bus" with the following modifications +and additions : + +Required properties : + - compatible : Should be "fsl-usb2-mph" for multi port host USB + controllers, or "fsl-usb2-dr" for dual role USB controllers + or "fsl,mpc5121-usb2-dr" for dual role USB controllers of MPC5121 + - phy_type : For multi port host USB controllers, should be one of + "ulpi", or "serial". For dual role USB controllers, should be + one of "ulpi", "utmi", "utmi_wide", or "serial". + - reg : Offset and length of the register set for the device + - port0 : boolean; if defined, indicates port0 is connected for + fsl-usb2-mph compatible controllers. Either this property or + "port1" (or both) must be defined for "fsl-usb2-mph" compatible + controllers. + - port1 : boolean; if defined, indicates port1 is connected for + fsl-usb2-mph compatible controllers. Either this property or + "port0" (or both) must be defined for "fsl-usb2-mph" compatible + controllers. + - dr_mode : indicates the working mode for "fsl-usb2-dr" compatible + controllers. Can be "host", "peripheral", or "otg". Default to + "host" if not defined for backward compatibility. + +Recommended properties : + - interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Optional properties : + - fsl,invert-drvvbus : boolean; for MPC5121 USB0 only. Indicates the + port power polarity of internal PHY signal DRVVBUS is inverted. + - fsl,invert-pwr-fault : boolean; for MPC5121 USB0 only. Indicates + the PWR_FAULT signal polarity is inverted. + +Example multi port host USB controller device node : + usb@22000 { + compatible = "fsl-usb2-mph"; + reg = <22000 1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = <700>; + interrupts = <27 1>; + phy_type = "ulpi"; + port0; + port1; + }; + +Example dual role USB controller device node : + usb@23000 { + compatible = "fsl-usb2-dr"; + reg = <23000 1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = <700>; + interrupts = <26 1>; + dr_mode = "otg"; + phy = "ulpi"; + }; + +Example dual role USB controller device node for MPC5121ADS: + + usb@4000 { + compatible = "fsl,mpc5121-usb2-dr"; + reg = <0x4000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = < &ipic >; + interrupts = <44 0x8>; + dr_mode = "otg"; + phy_type = "utmi_wide"; + fsl,invert-drvvbus; + fsl,invert-pwr-fault; + }; diff --git a/Documentation/devicetree/bindings/usb/tegra-usb.txt b/Documentation/devicetree/bindings/usb/tegra-usb.txt new file mode 100644 index 00000000..007005dd --- /dev/null +++ b/Documentation/devicetree/bindings/usb/tegra-usb.txt @@ -0,0 +1,26 @@ +Tegra SOC USB controllers + +The device node for a USB controller that is part of a Tegra +SOC is as described in the document "Open Firmware Recommended +Practice : Universal Serial Bus" with the following modifications +and additions : + +Required properties : + - compatible : Should be "nvidia,tegra20-ehci" for USB controllers + used in host mode. + - phy_type : Should be one of "ulpi" or "utmi". + - nvidia,vbus-gpio : If present, specifies a gpio that needs to be + activated for the bus to be powered. + +Optional properties: + - dr_mode : dual role mode. Indicates the working mode for + nvidia,tegra20-ehci compatible controllers. Can be "host", "peripheral", + or "otg". Default to "host" if not defined for backward compatibility. + host means this is a host controller + peripheral means it is device controller + otg means it can operate as either ("on the go") + - nvidia,has-legacy-mode : boolean indicates whether this controller can + operate in legacy mode (as APX 2500 / 2600). In legacy mode some + registers are accessed through the APB_MISC base address instead of + the USB controller. Since this is a legacy issue it probably does not + warrant a compatible string of its own. diff --git a/Documentation/devicetree/bindings/usb/usb-ehci.txt b/Documentation/devicetree/bindings/usb/usb-ehci.txt new file mode 100644 index 00000000..fa18612f --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-ehci.txt @@ -0,0 +1,25 @@ +USB EHCI controllers + +Required properties: + - compatible : should be "usb-ehci". + - reg : should contain at least address and length of the standard EHCI + register set for the device. Optional platform-dependent registers + (debug-port or other) can be also specified here, but only after + definition of standard EHCI registers. + - interrupts : one EHCI interrupt should be described here. +If device registers are implemented in big endian mode, the device +node should have "big-endian-regs" property. +If controller implementation operates with big endian descriptors, +"big-endian-desc" property should be specified. +If both big endian registers and descriptors are used by the controller +implementation, "big-endian" property can be specified instead of having +both "big-endian-regs" and "big-endian-desc". + +Example (Sequoia 440EPx): + ehci@e0000300 { + compatible = "ibm,usb-ehci-440epx", "usb-ehci"; + interrupt-parent = <&UIC0>; + interrupts = <1a 4>; + reg = <0 e0000300 90 0 e0000390 70>; + big-endian; + }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt new file mode 100644 index 00000000..82ac057a --- /dev/null +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -0,0 +1,48 @@ +Device tree binding vendor prefix registry. Keep list in alphabetical order. + +This isn't an exhaustive list, but you should add new prefixes to it before +using them to avoid name-space collisions. + +adi Analog Devices, Inc. +amcc Applied Micro Circuits Corporation (APM, formally AMCC) +apm Applied Micro Circuits Corporation (APM) +arm ARM Ltd. +atmel Atmel Corporation +cavium Cavium, Inc. +chrp Common Hardware Reference Platform +cortina Cortina Systems, Inc. +dallas Maxim Integrated Products (formerly Dallas Semiconductor) +denx Denx Software Engineering +epson Seiko Epson Corp. +est ESTeem Wireless Modems +fsl Freescale Semiconductor +GEFanuc GE Fanuc Intelligent Platforms Embedded Systems, Inc. +gef GE Fanuc Intelligent Platforms Embedded Systems, Inc. +hp Hewlett Packard +ibm International Business Machines (IBM) +idt Integrated Device Technologies, Inc. +intercontrol Inter Control Group +linux Linux-specific binding +marvell Marvell Technology Group Ltd. +maxim Maxim Integrated Products +mosaixtech Mosaix Technologies, Inc. +national National Semiconductor +nintendo Nintendo +nvidia NVIDIA +nxp NXP Semiconductors +picochip Picochip Ltd +powervr Imagination Technologies +qcom Qualcomm, Inc. +ramtron Ramtron International +realtek Realtek Semiconductor Corp. +samsung Samsung Semiconductor +sbs Smart Battery System +schindler Schindler +sil Silicon Image +simtek +sirf SiRF Technology, Inc. +st STMicroelectronics +stericsson ST-Ericsson +ti Texas Instruments +wlf Wolfson Microelectronics +xlnx Xilinx diff --git a/Documentation/devicetree/bindings/virtio/mmio.txt b/Documentation/devicetree/bindings/virtio/mmio.txt new file mode 100644 index 00000000..5069c1b8 --- /dev/null +++ b/Documentation/devicetree/bindings/virtio/mmio.txt @@ -0,0 +1,17 @@ +* virtio memory mapped device + +See http://ozlabs.org/~rusty/virtio-spec/ for more details. + +Required properties: + +- compatible: "virtio,mmio" compatibility string +- reg: control registers base address and size including configuration space +- interrupts: interrupt generated by the device + +Example: + + virtio_block@3000 { + compatible = "virtio,mmio"; + reg = <0x3000 0x100>; + interrupts = <41>; + } diff --git a/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt b/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt new file mode 100644 index 00000000..2144af1a --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt @@ -0,0 +1,14 @@ +* Freescale i.MX Watchdog Timer (WDT) Controller + +Required properties: +- compatible : Should be "fsl,<soc>-wdt" +- reg : Should contain WDT registers location and length +- interrupts : Should contain WDT interrupt + +Examples: + +wdt@73f98000 { + compatible = "fsl,imx51-wdt", "fsl,imx21-wdt"; + reg = <0x73f98000 0x4000>; + interrupts = <58>; +}; diff --git a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt new file mode 100644 index 00000000..79ead826 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt @@ -0,0 +1,11 @@ +* Samsung's Watchdog Timer Controller + +The Samsung's Watchdog controller is used for resuming system operation +after a preset amount of time during which the WDT reset event has not +occured. + +Required properties: +- compatible : should be "samsung,s3c2410-wdt" +- reg : base physical address of the controller and length of memory mapped + region. +- interrupts : interrupt number to the cpu. diff --git a/Documentation/devicetree/bindings/x86/ce4100.txt b/Documentation/devicetree/bindings/x86/ce4100.txt new file mode 100644 index 00000000..b49ae593 --- /dev/null +++ b/Documentation/devicetree/bindings/x86/ce4100.txt @@ -0,0 +1,38 @@ +CE4100 Device Tree Bindings +--------------------------- + +The CE4100 SoC uses for in core peripherals the following compatible +format: <vendor>,<chip>-<device>. +Many of the "generic" devices like HPET or IO APIC have the ce4100 +name in their compatible property because they first appeared in this +SoC. + +The CPU node +------------ + cpu@0 { + device_type = "cpu"; + compatible = "intel,ce4100"; + reg = <0>; + lapic = <&lapic0>; + }; + +The reg property describes the CPU number. The lapic property points to +the local APIC timer. + +The SoC node +------------ + +This node describes the in-core peripherals. Required property: + compatible = "intel,ce4100-cp"; + +The PCI node +------------ +This node describes the PCI bus on the SoC. Its property should be + compatible = "intel,ce4100-pci", "pci"; + +If the OS is using the IO-APIC for interrupt routing then the reported +interrupt numbers for devices is no longer true. In order to obtain the +correct interrupt number, the child node which represents the device has +to contain the interrupt property. Besides the interrupt property it has +to contain at least the reg property containing the PCI bus address and +compatible property according to "PCI Bus Binding Revision 2.1". diff --git a/Documentation/devicetree/bindings/x86/interrupt.txt b/Documentation/devicetree/bindings/x86/interrupt.txt new file mode 100644 index 00000000..7d19f494 --- /dev/null +++ b/Documentation/devicetree/bindings/x86/interrupt.txt @@ -0,0 +1,26 @@ +Interrupt chips +--------------- + +* Intel I/O Advanced Programmable Interrupt Controller (IO APIC) + + Required properties: + -------------------- + compatible = "intel,ce4100-ioapic"; + #interrupt-cells = <2>; + + Device's interrupt property: + + interrupts = <P S>; + + The first number (P) represents the interrupt pin which is wired to the + IO APIC. The second number (S) represents the sense of interrupt which + should be configured and can be one of: + 0 - Edge Rising + 1 - Level Low + 2 - Level High + 3 - Edge Falling + +* Local APIC + Required property: + + compatible = "intel,ce4100-lapic"; diff --git a/Documentation/devicetree/bindings/x86/timer.txt b/Documentation/devicetree/bindings/x86/timer.txt new file mode 100644 index 00000000..c688af58 --- /dev/null +++ b/Documentation/devicetree/bindings/x86/timer.txt @@ -0,0 +1,6 @@ +Timers +------ + +* High Precision Event Timer (HPET) + Required property: + compatible = "intel,ce4100-hpet"; diff --git a/Documentation/devicetree/bindings/xilinx.txt b/Documentation/devicetree/bindings/xilinx.txt new file mode 100644 index 00000000..299d0923 --- /dev/null +++ b/Documentation/devicetree/bindings/xilinx.txt @@ -0,0 +1,306 @@ + d) Xilinx IP cores + + The Xilinx EDK toolchain ships with a set of IP cores (devices) for use + in Xilinx Spartan and Virtex FPGAs. The devices cover the whole range + of standard device types (network, serial, etc.) and miscellaneous + devices (gpio, LCD, spi, etc). Also, since these devices are + implemented within the fpga fabric every instance of the device can be + synthesised with different options that change the behaviour. + + Each IP-core has a set of parameters which the FPGA designer can use to + control how the core is synthesized. Historically, the EDK tool would + extract the device parameters relevant to device drivers and copy them + into an 'xparameters.h' in the form of #define symbols. This tells the + device drivers how the IP cores are configured, but it requires the kernel + to be recompiled every time the FPGA bitstream is resynthesized. + + The new approach is to export the parameters into the device tree and + generate a new device tree each time the FPGA bitstream changes. The + parameters which used to be exported as #defines will now become + properties of the device node. In general, device nodes for IP-cores + will take the following form: + + (name): (generic-name)@(base-address) { + compatible = "xlnx,(ip-core-name)-(HW_VER)" + [, (list of compatible devices), ...]; + reg = <(baseaddr) (size)>; + interrupt-parent = <&interrupt-controller-phandle>; + interrupts = < ... >; + xlnx,(parameter1) = "(string-value)"; + xlnx,(parameter2) = <(int-value)>; + }; + + (generic-name): an open firmware-style name that describes the + generic class of device. Preferably, this is one word, such + as 'serial' or 'ethernet'. + (ip-core-name): the name of the ip block (given after the BEGIN + directive in system.mhs). Should be in lowercase + and all underscores '_' converted to dashes '-'. + (name): is derived from the "PARAMETER INSTANCE" value. + (parameter#): C_* parameters from system.mhs. The C_ prefix is + dropped from the parameter name, the name is converted + to lowercase and all underscore '_' characters are + converted to dashes '-'. + (baseaddr): the baseaddr parameter value (often named C_BASEADDR). + (HW_VER): from the HW_VER parameter. + (size): the address range size (often C_HIGHADDR - C_BASEADDR + 1). + + Typically, the compatible list will include the exact IP core version + followed by an older IP core version which implements the same + interface or any other device with the same interface. + + 'reg', 'interrupt-parent' and 'interrupts' are all optional properties. + + For example, the following block from system.mhs: + + BEGIN opb_uartlite + PARAMETER INSTANCE = opb_uartlite_0 + PARAMETER HW_VER = 1.00.b + PARAMETER C_BAUDRATE = 115200 + PARAMETER C_DATA_BITS = 8 + PARAMETER C_ODD_PARITY = 0 + PARAMETER C_USE_PARITY = 0 + PARAMETER C_CLK_FREQ = 50000000 + PARAMETER C_BASEADDR = 0xEC100000 + PARAMETER C_HIGHADDR = 0xEC10FFFF + BUS_INTERFACE SOPB = opb_7 + PORT OPB_Clk = CLK_50MHz + PORT Interrupt = opb_uartlite_0_Interrupt + PORT RX = opb_uartlite_0_RX + PORT TX = opb_uartlite_0_TX + PORT OPB_Rst = sys_bus_reset_0 + END + + becomes the following device tree node: + + opb_uartlite_0: serial@ec100000 { + device_type = "serial"; + compatible = "xlnx,opb-uartlite-1.00.b"; + reg = <ec100000 10000>; + interrupt-parent = <&opb_intc_0>; + interrupts = <1 0>; // got this from the opb_intc parameters + current-speed = <d#115200>; // standard serial device prop + clock-frequency = <d#50000000>; // standard serial device prop + xlnx,data-bits = <8>; + xlnx,odd-parity = <0>; + xlnx,use-parity = <0>; + }; + + Some IP cores actually implement 2 or more logical devices. In + this case, the device should still describe the whole IP core with + a single node and add a child node for each logical device. The + ranges property can be used to translate from parent IP-core to the + registers of each device. In addition, the parent node should be + compatible with the bus type 'xlnx,compound', and should contain + #address-cells and #size-cells, as with any other bus. (Note: this + makes the assumption that both logical devices have the same bus + binding. If this is not true, then separate nodes should be used + for each logical device). The 'cell-index' property can be used to + enumerate logical devices within an IP core. For example, the + following is the system.mhs entry for the dual ps2 controller found + on the ml403 reference design. + + BEGIN opb_ps2_dual_ref + PARAMETER INSTANCE = opb_ps2_dual_ref_0 + PARAMETER HW_VER = 1.00.a + PARAMETER C_BASEADDR = 0xA9000000 + PARAMETER C_HIGHADDR = 0xA9001FFF + BUS_INTERFACE SOPB = opb_v20_0 + PORT Sys_Intr1 = ps2_1_intr + PORT Sys_Intr2 = ps2_2_intr + PORT Clkin1 = ps2_clk_rx_1 + PORT Clkin2 = ps2_clk_rx_2 + PORT Clkpd1 = ps2_clk_tx_1 + PORT Clkpd2 = ps2_clk_tx_2 + PORT Rx1 = ps2_d_rx_1 + PORT Rx2 = ps2_d_rx_2 + PORT Txpd1 = ps2_d_tx_1 + PORT Txpd2 = ps2_d_tx_2 + END + + It would result in the following device tree nodes: + + opb_ps2_dual_ref_0: opb-ps2-dual-ref@a9000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "xlnx,compound"; + ranges = <0 a9000000 2000>; + // If this device had extra parameters, then they would + // go here. + ps2@0 { + compatible = "xlnx,opb-ps2-dual-ref-1.00.a"; + reg = <0 40>; + interrupt-parent = <&opb_intc_0>; + interrupts = <3 0>; + cell-index = <0>; + }; + ps2@1000 { + compatible = "xlnx,opb-ps2-dual-ref-1.00.a"; + reg = <1000 40>; + interrupt-parent = <&opb_intc_0>; + interrupts = <3 0>; + cell-index = <0>; + }; + }; + + Also, the system.mhs file defines bus attachments from the processor + to the devices. The device tree structure should reflect the bus + attachments. Again an example; this system.mhs fragment: + + BEGIN ppc405_virtex4 + PARAMETER INSTANCE = ppc405_0 + PARAMETER HW_VER = 1.01.a + BUS_INTERFACE DPLB = plb_v34_0 + BUS_INTERFACE IPLB = plb_v34_0 + END + + BEGIN opb_intc + PARAMETER INSTANCE = opb_intc_0 + PARAMETER HW_VER = 1.00.c + PARAMETER C_BASEADDR = 0xD1000FC0 + PARAMETER C_HIGHADDR = 0xD1000FDF + BUS_INTERFACE SOPB = opb_v20_0 + END + + BEGIN opb_uart16550 + PARAMETER INSTANCE = opb_uart16550_0 + PARAMETER HW_VER = 1.00.d + PARAMETER C_BASEADDR = 0xa0000000 + PARAMETER C_HIGHADDR = 0xa0001FFF + BUS_INTERFACE SOPB = opb_v20_0 + END + + BEGIN plb_v34 + PARAMETER INSTANCE = plb_v34_0 + PARAMETER HW_VER = 1.02.a + END + + BEGIN plb_bram_if_cntlr + PARAMETER INSTANCE = plb_bram_if_cntlr_0 + PARAMETER HW_VER = 1.00.b + PARAMETER C_BASEADDR = 0xFFFF0000 + PARAMETER C_HIGHADDR = 0xFFFFFFFF + BUS_INTERFACE SPLB = plb_v34_0 + END + + BEGIN plb2opb_bridge + PARAMETER INSTANCE = plb2opb_bridge_0 + PARAMETER HW_VER = 1.01.a + PARAMETER C_RNG0_BASEADDR = 0x20000000 + PARAMETER C_RNG0_HIGHADDR = 0x3FFFFFFF + PARAMETER C_RNG1_BASEADDR = 0x60000000 + PARAMETER C_RNG1_HIGHADDR = 0x7FFFFFFF + PARAMETER C_RNG2_BASEADDR = 0x80000000 + PARAMETER C_RNG2_HIGHADDR = 0xBFFFFFFF + PARAMETER C_RNG3_BASEADDR = 0xC0000000 + PARAMETER C_RNG3_HIGHADDR = 0xDFFFFFFF + BUS_INTERFACE SPLB = plb_v34_0 + BUS_INTERFACE MOPB = opb_v20_0 + END + + Gives this device tree (some properties removed for clarity): + + plb@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "xlnx,plb-v34-1.02.a"; + device_type = "ibm,plb"; + ranges; // 1:1 translation + + plb_bram_if_cntrl_0: bram@ffff0000 { + reg = <ffff0000 10000>; + } + + opb@20000000 { + #address-cells = <1>; + #size-cells = <1>; + ranges = <20000000 20000000 20000000 + 60000000 60000000 20000000 + 80000000 80000000 40000000 + c0000000 c0000000 20000000>; + + opb_uart16550_0: serial@a0000000 { + reg = <a00000000 2000>; + }; + + opb_intc_0: interrupt-controller@d1000fc0 { + reg = <d1000fc0 20>; + }; + }; + }; + + That covers the general approach to binding xilinx IP cores into the + device tree. The following are bindings for specific devices: + + i) Xilinx ML300 Framebuffer + + Simple framebuffer device from the ML300 reference design (also on the + ML403 reference design as well as others). + + Optional properties: + - resolution = <xres yres> : pixel resolution of framebuffer. Some + implementations use a different resolution. + Default is <d#640 d#480> + - virt-resolution = <xvirt yvirt> : Size of framebuffer in memory. + Default is <d#1024 d#480>. + - rotate-display (empty) : rotate display 180 degrees. + + ii) Xilinx SystemACE + + The Xilinx SystemACE device is used to program FPGAs from an FPGA + bitstream stored on a CF card. It can also be used as a generic CF + interface device. + + Optional properties: + - 8-bit (empty) : Set this property for SystemACE in 8 bit mode + + iii) Xilinx EMAC and Xilinx TEMAC + + Xilinx Ethernet devices. In addition to general xilinx properties + listed above, nodes for these devices should include a phy-handle + property, and may include other common network device properties + like local-mac-address. + + iv) Xilinx Uartlite + + Xilinx uartlite devices are simple fixed speed serial ports. + + Required properties: + - current-speed : Baud rate of uartlite + + v) Xilinx hwicap + + Xilinx hwicap devices provide access to the configuration logic + of the FPGA through the Internal Configuration Access Port + (ICAP). The ICAP enables partial reconfiguration of the FPGA, + readback of the configuration information, and some control over + 'warm boots' of the FPGA fabric. + + Required properties: + - xlnx,family : The family of the FPGA, necessary since the + capabilities of the underlying ICAP hardware + differ between different families. May be + 'virtex2p', 'virtex4', or 'virtex5'. + + vi) Xilinx Uart 16550 + + Xilinx UART 16550 devices are very similar to the NS16550 but with + different register spacing and an offset from the base address. + + Required properties: + - clock-frequency : Frequency of the clock input + - reg-offset : A value of 3 is required + - reg-shift : A value of 2 is required + + vii) Xilinx USB Host controller + + The Xilinx USB host controller is EHCI compatible but with a different + base address for the EHCI registers, and it is always a big-endian + USB Host controller. The hardware can be configured as high speed only, + or high speed/full speed hybrid. + + Required properties: + - xlnx,support-usb-fs: A value 0 means the core is built as high speed + only. A value 1 means the core also supports + full speed devices. + |