diff options
Diffstat (limited to 'ANDROID_3.4.5/init')
| -rw-r--r-- | ANDROID_3.4.5/init/calibrate.c | 301 |
1 files changed, 0 insertions, 301 deletions
diff --git a/ANDROID_3.4.5/init/calibrate.c b/ANDROID_3.4.5/init/calibrate.c deleted file mode 100644 index fda0a7b0..00000000 --- a/ANDROID_3.4.5/init/calibrate.c +++ /dev/null @@ -1,301 +0,0 @@ -/* calibrate.c: default delay calibration - * - * Excised from init/main.c - * Copyright (C) 1991, 1992 Linus Torvalds - */ - -#include <linux/jiffies.h> -#include <linux/delay.h> -#include <linux/init.h> -#include <linux/timex.h> -#include <linux/smp.h> -#include <linux/percpu.h> - -unsigned long lpj_fine; -unsigned long preset_lpj; -static int __init lpj_setup(char *str) -{ - preset_lpj = simple_strtoul(str,NULL,0); - return 1; -} - -__setup("lpj=", lpj_setup); - -#ifdef ARCH_HAS_READ_CURRENT_TIMER - -/* This routine uses the read_current_timer() routine and gets the - * loops per jiffy directly, instead of guessing it using delay(). - * Also, this code tries to handle non-maskable asynchronous events - * (like SMIs) - */ -#define DELAY_CALIBRATION_TICKS ((HZ < 100) ? 1 : (HZ/100)) -#define MAX_DIRECT_CALIBRATION_RETRIES 5 - -static unsigned long __cpuinit calibrate_delay_direct(void) -{ - unsigned long pre_start, start, post_start; - unsigned long pre_end, end, post_end; - unsigned long start_jiffies; - unsigned long timer_rate_min, timer_rate_max; - unsigned long good_timer_sum = 0; - unsigned long good_timer_count = 0; - unsigned long measured_times[MAX_DIRECT_CALIBRATION_RETRIES]; - int max = -1; /* index of measured_times with max/min values or not set */ - int min = -1; - int i; - - if (read_current_timer(&pre_start) < 0 ) - return 0; - - /* - * A simple loop like - * while ( jiffies < start_jiffies+1) - * start = read_current_timer(); - * will not do. As we don't really know whether jiffy switch - * happened first or timer_value was read first. And some asynchronous - * event can happen between these two events introducing errors in lpj. - * - * So, we do - * 1. pre_start <- When we are sure that jiffy switch hasn't happened - * 2. check jiffy switch - * 3. start <- timer value before or after jiffy switch - * 4. post_start <- When we are sure that jiffy switch has happened - * - * Note, we don't know anything about order of 2 and 3. - * Now, by looking at post_start and pre_start difference, we can - * check whether any asynchronous event happened or not - */ - - for (i = 0; i < MAX_DIRECT_CALIBRATION_RETRIES; i++) { - pre_start = 0; - read_current_timer(&start); - start_jiffies = jiffies; - while (time_before_eq(jiffies, start_jiffies + 1)) { - pre_start = start; - read_current_timer(&start); - } - read_current_timer(&post_start); - - pre_end = 0; - end = post_start; - while (time_before_eq(jiffies, start_jiffies + 1 + - DELAY_CALIBRATION_TICKS)) { - pre_end = end; - read_current_timer(&end); - } - read_current_timer(&post_end); - - timer_rate_max = (post_end - pre_start) / - DELAY_CALIBRATION_TICKS; - timer_rate_min = (pre_end - post_start) / - DELAY_CALIBRATION_TICKS; - - /* - * If the upper limit and lower limit of the timer_rate is - * >= 12.5% apart, redo calibration. - */ - if (start >= post_end) - printk(KERN_NOTICE "calibrate_delay_direct() ignoring " - "timer_rate as we had a TSC wrap around" - " start=%lu >=post_end=%lu\n", - start, post_end); - if (start < post_end && pre_start != 0 && pre_end != 0 && - (timer_rate_max - timer_rate_min) < (timer_rate_max >> 3)) { - good_timer_count++; - good_timer_sum += timer_rate_max; - measured_times[i] = timer_rate_max; - if (max < 0 || timer_rate_max > measured_times[max]) - max = i; - if (min < 0 || timer_rate_max < measured_times[min]) - min = i; - } else - measured_times[i] = 0; - - } - - /* - * Find the maximum & minimum - if they differ too much throw out the - * one with the largest difference from the mean and try again... - */ - while (good_timer_count > 1) { - unsigned long estimate; - unsigned long maxdiff; - - /* compute the estimate */ - estimate = (good_timer_sum/good_timer_count); - maxdiff = estimate >> 3; - - /* if range is within 12% let's take it */ - if ((measured_times[max] - measured_times[min]) < maxdiff) - return estimate; - - /* ok - drop the worse value and try again... */ - good_timer_sum = 0; - good_timer_count = 0; - if ((measured_times[max] - estimate) < - (estimate - measured_times[min])) { - printk(KERN_NOTICE "calibrate_delay_direct() dropping " - "min bogoMips estimate %d = %lu\n", - min, measured_times[min]); - measured_times[min] = 0; - min = max; - } else { - printk(KERN_NOTICE "calibrate_delay_direct() dropping " - "max bogoMips estimate %d = %lu\n", - max, measured_times[max]); - measured_times[max] = 0; - max = min; - } - - for (i = 0; i < MAX_DIRECT_CALIBRATION_RETRIES; i++) { - if (measured_times[i] == 0) - continue; - good_timer_count++; - good_timer_sum += measured_times[i]; - if (measured_times[i] < measured_times[min]) - min = i; - if (measured_times[i] > measured_times[max]) - max = i; - } - - } - - printk(KERN_NOTICE "calibrate_delay_direct() failed to get a good " - "estimate for loops_per_jiffy.\nProbably due to long platform " - "interrupts. Consider using \"lpj=\" boot option.\n"); - return 0; -} -#else -static unsigned long __cpuinit calibrate_delay_direct(void) {return 0;} -#endif - -/* - * This is the number of bits of precision for the loops_per_jiffy. Each - * time we refine our estimate after the first takes 1.5/HZ seconds, so try - * to start with a good estimate. - * For the boot cpu we can skip the delay calibration and assign it a value - * calculated based on the timer frequency. - * For the rest of the CPUs we cannot assume that the timer frequency is same as - * the cpu frequency, hence do the calibration for those. - */ -#define LPS_PREC 8 - -static unsigned long __cpuinit calibrate_delay_converge(void) -{ - /* First stage - slowly accelerate to find initial bounds */ - unsigned long lpj, lpj_base, ticks, loopadd, loopadd_base, chop_limit; - int trials = 0, band = 0, trial_in_band = 0; - - lpj = (1<<12); - - /* wait for "start of" clock tick */ - ticks = jiffies; - while (ticks == jiffies) - ; /* nothing */ - /* Go .. */ - ticks = jiffies; - do { - if (++trial_in_band == (1<<band)) { - ++band; - trial_in_band = 0; - } - __delay(lpj * band); - trials += band; - } while (ticks == jiffies); - /* - * We overshot, so retreat to a clear underestimate. Then estimate - * the largest likely undershoot. This defines our chop bounds. - */ - trials -= band; - loopadd_base = lpj * band; - lpj_base = lpj * trials; - -recalibrate: - lpj = lpj_base; - loopadd = loopadd_base; - - /* - * Do a binary approximation to get lpj set to - * equal one clock (up to LPS_PREC bits) - */ - chop_limit = lpj >> LPS_PREC; - while (loopadd > chop_limit) { - lpj += loopadd; - ticks = jiffies; - while (ticks == jiffies) - ; /* nothing */ - ticks = jiffies; - __delay(lpj); - if (jiffies != ticks) /* longer than 1 tick */ - lpj -= loopadd; - loopadd >>= 1; - } - /* - * If we incremented every single time possible, presume we've - * massively underestimated initially, and retry with a higher - * start, and larger range. (Only seen on x86_64, due to SMIs) - */ - if (lpj + loopadd * 2 == lpj_base + loopadd_base * 2) { - lpj_base = lpj; - loopadd_base <<= 2; - goto recalibrate; - } - - return lpj; -} - -static DEFINE_PER_CPU(unsigned long, cpu_loops_per_jiffy) = { 0 }; - -/* - * Check if cpu calibration delay is already known. For example, - * some processors with multi-core sockets may have all cores - * with the same calibration delay. - * - * Architectures should override this function if a faster calibration - * method is available. - */ -unsigned long __attribute__((weak)) __cpuinit calibrate_delay_is_known(void) -{ - return 0; -} - -void __cpuinit calibrate_delay(void) -{ - unsigned long lpj; - static bool printed; - int this_cpu = smp_processor_id(); - - if (per_cpu(cpu_loops_per_jiffy, this_cpu)) { - lpj = per_cpu(cpu_loops_per_jiffy, this_cpu); - if (!printed) - pr_info("Calibrating delay loop (skipped) " - "already calibrated this CPU"); - } else if (preset_lpj) { - lpj = preset_lpj; - if (!printed) - pr_info("Calibrating delay loop (skipped) " - "preset value.. "); - } else if ((!printed) && lpj_fine) { - lpj = lpj_fine; - pr_info("Calibrating delay loop (skipped), " - "value calculated using timer frequency.. "); - } else if ((lpj = calibrate_delay_is_known())) { - ; - } else if ((lpj = calibrate_delay_direct()) != 0) { - if (!printed) - pr_info("Calibrating delay using timer " - "specific routine.. "); - } else { - if (!printed) - pr_info("Calibrating delay loop... "); - lpj = calibrate_delay_converge(); - } - per_cpu(cpu_loops_per_jiffy, this_cpu) = lpj; - if (!printed) - pr_cont("%lu.%02lu BogoMIPS (lpj=%lu)\n", - lpj/(500000/HZ), - (lpj/(5000/HZ)) % 100, lpj); - - loops_per_jiffy = lpj; - printed = true; -} |