Moved, renamed, and deleted files

The original directory structure was scattered and unorganized.
Changes are basically to make it look like kernel structure.

1 files changed, 3713 insertions, 0 deletions

diff --git a/include/net/mac80211.h b/include/net/mac80211.h
new file mode 100644
index 00000000..9210bdc7
--- /dev/null
+++ b/include/net/mac80211.h
@@ -0,0 +1,3713 @@
+/*
+ * mac80211 <-> driver interface
+ *
+ * Copyright 2002-2005, Devicescape Software, Inc.
+ * Copyright 2006-2007	Jiri Benc <jbenc@suse.cz>
+ * Copyright 2007-2010	Johannes Berg <johannes@sipsolutions.net>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef MAC80211_H
+#define MAC80211_H
+
+#include <linux/bug.h>
+#include <linux/kernel.h>
+#include <linux/if_ether.h>
+#include <linux/skbuff.h>
+#include <linux/ieee80211.h>
+#include <net/cfg80211.h>
+#include <asm/unaligned.h>
+
+/**
+ * DOC: Introduction
+ *
+ * mac80211 is the Linux stack for 802.11 hardware that implements
+ * only partial functionality in hard- or firmware. This document
+ * defines the interface between mac80211 and low-level hardware
+ * drivers.
+ */
+
+/**
+ * DOC: Calling mac80211 from interrupts
+ *
+ * Only ieee80211_tx_status_irqsafe() and ieee80211_rx_irqsafe() can be
+ * called in hardware interrupt context. The low-level driver must not call any
+ * other functions in hardware interrupt context. If there is a need for such
+ * call, the low-level driver should first ACK the interrupt and perform the
+ * IEEE 802.11 code call after this, e.g. from a scheduled workqueue or even
+ * tasklet function.
+ *
+ * NOTE: If the driver opts to use the _irqsafe() functions, it may not also
+ *	 use the non-IRQ-safe functions!
+ */
+
+/**
+ * DOC: Warning
+ *
+ * If you're reading this document and not the header file itself, it will
+ * be incomplete because not all documentation has been converted yet.
+ */
+
+/**
+ * DOC: Frame format
+ *
+ * As a general rule, when frames are passed between mac80211 and the driver,
+ * they start with the IEEE 802.11 header and include the same octets that are
+ * sent over the air except for the FCS which should be calculated by the
+ * hardware.
+ *
+ * There are, however, various exceptions to this rule for advanced features:
+ *
+ * The first exception is for hardware encryption and decryption offload
+ * where the IV/ICV may or may not be generated in hardware.
+ *
+ * Secondly, when the hardware handles fragmentation, the frame handed to
+ * the driver from mac80211 is the MSDU, not the MPDU.
+ *
+ * Finally, for received frames, the driver is able to indicate that it has
+ * filled a radiotap header and put that in front of the frame; if it does
+ * not do so then mac80211 may add this under certain circumstances.
+ */
+
+/**
+ * DOC: mac80211 workqueue
+ *
+ * mac80211 provides its own workqueue for drivers and internal mac80211 use.
+ * The workqueue is a single threaded workqueue and can only be accessed by
+ * helpers for sanity checking. Drivers must ensure all work added onto the
+ * mac80211 workqueue should be cancelled on the driver stop() callback.
+ *
+ * mac80211 will flushed the workqueue upon interface removal and during
+ * suspend.
+ *
+ * All work performed on the mac80211 workqueue must not acquire the RTNL lock.
+ *
+ */
+
+struct device;
+
+/**
+ * enum ieee80211_max_queues - maximum number of queues
+ *
+ * @IEEE80211_MAX_QUEUES: Maximum number of regular device queues.
+ */
+enum ieee80211_max_queues {
+	IEEE80211_MAX_QUEUES =		4,
+};
+
+/**
+ * enum ieee80211_ac_numbers - AC numbers as used in mac80211
+ * @IEEE80211_AC_VO: voice
+ * @IEEE80211_AC_VI: video
+ * @IEEE80211_AC_BE: best effort
+ * @IEEE80211_AC_BK: background
+ */
+enum ieee80211_ac_numbers {
+	IEEE80211_AC_VO		= 0,
+	IEEE80211_AC_VI		= 1,
+	IEEE80211_AC_BE		= 2,
+	IEEE80211_AC_BK		= 3,
+};
+#define IEEE80211_NUM_ACS	4
+
+/**
+ * struct ieee80211_tx_queue_params - transmit queue configuration
+ *
+ * The information provided in this structure is required for QoS
+ * transmit queue configuration. Cf. IEEE 802.11 7.3.2.29.
+ *
+ * @aifs: arbitration interframe space [0..255]
+ * @cw_min: minimum contention window [a value of the form
+ *	2^n-1 in the range 1..32767]
+ * @cw_max: maximum contention window [like @cw_min]
+ * @txop: maximum burst time in units of 32 usecs, 0 meaning disabled
+ * @uapsd: is U-APSD mode enabled for the queue
+ */
+struct ieee80211_tx_queue_params {
+	u16 txop;
+	u16 cw_min;
+	u16 cw_max;
+	u8 aifs;
+	bool uapsd;
+};
+
+struct ieee80211_low_level_stats {
+	unsigned int dot11ACKFailureCount;
+	unsigned int dot11RTSFailureCount;
+	unsigned int dot11FCSErrorCount;
+	unsigned int dot11RTSSuccessCount;
+};
+
+/**
+ * enum ieee80211_bss_change - BSS change notification flags
+ *
+ * These flags are used with the bss_info_changed() callback
+ * to indicate which BSS parameter changed.
+ *
+ * @BSS_CHANGED_ASSOC: association status changed (associated/disassociated),
+ *	also implies a change in the AID.
+ * @BSS_CHANGED_ERP_CTS_PROT: CTS protection changed
+ * @BSS_CHANGED_ERP_PREAMBLE: preamble changed
+ * @BSS_CHANGED_ERP_SLOT: slot timing changed
+ * @BSS_CHANGED_HT: 802.11n parameters changed
+ * @BSS_CHANGED_BASIC_RATES: Basic rateset changed
+ * @BSS_CHANGED_BEACON_INT: Beacon interval changed
+ * @BSS_CHANGED_BSSID: BSSID changed, for whatever
+ *	reason (IBSS and managed mode)
+ * @BSS_CHANGED_BEACON: Beacon data changed, retrieve
+ *	new beacon (beaconing modes)
+ * @BSS_CHANGED_BEACON_ENABLED: Beaconing should be
+ *	enabled/disabled (beaconing modes)
+ * @BSS_CHANGED_CQM: Connection quality monitor config changed
+ * @BSS_CHANGED_IBSS: IBSS join status changed
+ * @BSS_CHANGED_ARP_FILTER: Hardware ARP filter address list or state changed.
+ * @BSS_CHANGED_QOS: QoS for this association was enabled/disabled. Note
+ *	that it is only ever disabled for station mode.
+ * @BSS_CHANGED_IDLE: Idle changed for this BSS/interface.
+ * @BSS_CHANGED_SSID: SSID changed for this BSS (AP mode)
+ * @BSS_CHANGED_AP_PROBE_RESP: Probe Response changed for this BSS (AP mode)
+ */
+enum ieee80211_bss_change {
+	BSS_CHANGED_ASSOC		= 1<<0,
+	BSS_CHANGED_ERP_CTS_PROT	= 1<<1,
+	BSS_CHANGED_ERP_PREAMBLE	= 1<<2,
+	BSS_CHANGED_ERP_SLOT		= 1<<3,
+	BSS_CHANGED_HT			= 1<<4,
+	BSS_CHANGED_BASIC_RATES		= 1<<5,
+	BSS_CHANGED_BEACON_INT		= 1<<6,
+	BSS_CHANGED_BSSID		= 1<<7,
+	BSS_CHANGED_BEACON		= 1<<8,
+	BSS_CHANGED_BEACON_ENABLED	= 1<<9,
+	BSS_CHANGED_CQM			= 1<<10,
+	BSS_CHANGED_IBSS		= 1<<11,
+	BSS_CHANGED_ARP_FILTER		= 1<<12,
+	BSS_CHANGED_QOS			= 1<<13,
+	BSS_CHANGED_IDLE		= 1<<14,
+	BSS_CHANGED_SSID		= 1<<15,
+	BSS_CHANGED_AP_PROBE_RESP	= 1<<16,
+
+	/* when adding here, make sure to change ieee80211_reconfig */
+};
+
+/*
+ * The maximum number of IPv4 addresses listed for ARP filtering. If the number
+ * of addresses for an interface increase beyond this value, hardware ARP
+ * filtering will be disabled.
+ */
+#define IEEE80211_BSS_ARP_ADDR_LIST_LEN 4
+
+/**
+ * enum ieee80211_rssi_event - RSSI threshold event
+ * An indicator for when RSSI goes below/above a certain threshold.
+ * @RSSI_EVENT_HIGH: AP's rssi crossed the high threshold set by the driver.
+ * @RSSI_EVENT_LOW: AP's rssi crossed the low threshold set by the driver.
+ */
+enum ieee80211_rssi_event {
+	RSSI_EVENT_HIGH,
+	RSSI_EVENT_LOW,
+};
+
+/**
+ * struct ieee80211_bss_conf - holds the BSS's changing parameters
+ *
+ * This structure keeps information about a BSS (and an association
+ * to that BSS) that can change during the lifetime of the BSS.
+ *
+ * @assoc: association status
+ * @ibss_joined: indicates whether this station is part of an IBSS
+ *	or not
+ * @aid: association ID number, valid only when @assoc is true
+ * @use_cts_prot: use CTS protection
+ * @use_short_preamble: use 802.11b short preamble;
+ *	if the hardware cannot handle this it must set the
+ *	IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE hardware flag
+ * @use_short_slot: use short slot time (only relevant for ERP);
+ *	if the hardware cannot handle this it must set the
+ *	IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE hardware flag
+ * @dtim_period: num of beacons before the next DTIM, for beaconing,
+ *	valid in station mode only while @assoc is true and if also
+ *	requested by %IEEE80211_HW_NEED_DTIM_PERIOD (cf. also hw conf
+ *	@ps_dtim_period)
+ * @last_tsf: last beacon's/probe response's TSF timestamp (could be old
+ *	as it may have been received during scanning long ago)
+ * @beacon_int: beacon interval
+ * @assoc_capability: capabilities taken from assoc resp
+ * @basic_rates: bitmap of basic rates, each bit stands for an
+ *	index into the rate table configured by the driver in
+ *	the current band.
+ * @mcast_rate: per-band multicast rate index + 1 (0: disabled)
+ * @bssid: The BSSID for this BSS
+ * @enable_beacon: whether beaconing should be enabled or not
+ * @channel_type: Channel type for this BSS -- the hardware might be
+ *	configured for HT40+ while this BSS only uses no-HT, for
+ *	example.
+ * @ht_operation_mode: HT operation mode (like in &struct ieee80211_ht_info).
+ *	This field is only valid when the channel type is one of the HT types.
+ * @cqm_rssi_thold: Connection quality monitor RSSI threshold, a zero value
+ *	implies disabled
+ * @cqm_rssi_hyst: Connection quality monitor RSSI hysteresis
+ * @arp_addr_list: List of IPv4 addresses for hardware ARP filtering. The
+ *	may filter ARP queries targeted for other addresses than listed here.
+ *	The driver must allow ARP queries targeted for all address listed here
+ *	to pass through. An empty list implies no ARP queries need to pass.
+ * @arp_addr_cnt: Number of addresses currently on the list.
+ * @arp_filter_enabled: Enable ARP filtering - if enabled, the hardware may
+ *	filter ARP queries based on the @arp_addr_list, if disabled, the
+ *	hardware must not perform any ARP filtering. Note, that the filter will
+ *	be enabled also in promiscuous mode.
+ * @qos: This is a QoS-enabled BSS.
+ * @idle: This interface is idle. There's also a global idle flag in the
+ *	hardware config which may be more appropriate depending on what
+ *	your driver/device needs to do.
+ * @ssid: The SSID of the current vif. Only valid in AP-mode.
+ * @ssid_len: Length of SSID given in @ssid.
+ * @hidden_ssid: The SSID of the current vif is hidden. Only valid in AP-mode.
+ */
+struct ieee80211_bss_conf {
+	const u8 *bssid;
+	/* association related data */
+	bool assoc, ibss_joined;
+	u16 aid;
+	/* erp related data */
+	bool use_cts_prot;
+	bool use_short_preamble;
+	bool use_short_slot;
+	bool enable_beacon;
+	u8 dtim_period;
+	u16 beacon_int;
+	u16 assoc_capability;
+	u64 last_tsf;
+	u32 basic_rates;
+	int mcast_rate[IEEE80211_NUM_BANDS];
+	u16 ht_operation_mode;
+	s32 cqm_rssi_thold;
+	u32 cqm_rssi_hyst;
+	enum nl80211_channel_type channel_type;
+	__be32 arp_addr_list[IEEE80211_BSS_ARP_ADDR_LIST_LEN];
+	u8 arp_addr_cnt;
+	bool arp_filter_enabled;
+	bool qos;
+	bool idle;
+	u8 ssid[IEEE80211_MAX_SSID_LEN];
+	size_t ssid_len;
+	bool hidden_ssid;
+};
+
+/**
+ * enum mac80211_tx_control_flags - flags to describe transmission information/status
+ *
+ * These flags are used with the @flags member of &ieee80211_tx_info.
+ *
+ * @IEEE80211_TX_CTL_REQ_TX_STATUS: require TX status callback for this frame.
+ * @IEEE80211_TX_CTL_ASSIGN_SEQ: The driver has to assign a sequence
+ *	number to this frame, taking care of not overwriting the fragment
+ *	number and increasing the sequence number only when the
+ *	IEEE80211_TX_CTL_FIRST_FRAGMENT flag is set. mac80211 will properly
+ *	assign sequence numbers to QoS-data frames but cannot do so correctly
+ *	for non-QoS-data and management frames because beacons need them from
+ *	that counter as well and mac80211 cannot guarantee proper sequencing.
+ *	If this flag is set, the driver should instruct the hardware to
+ *	assign a sequence number to the frame or assign one itself. Cf. IEEE
+ *	802.11-2007 7.1.3.4.1 paragraph 3. This flag will always be set for
+ *	beacons and always be clear for frames without a sequence number field.
+ * @IEEE80211_TX_CTL_NO_ACK: tell the low level not to wait for an ack
+ * @IEEE80211_TX_CTL_CLEAR_PS_FILT: clear powersave filter for destination
+ *	station
+ * @IEEE80211_TX_CTL_FIRST_FRAGMENT: this is a first fragment of the frame
+ * @IEEE80211_TX_CTL_SEND_AFTER_DTIM: send this frame after DTIM beacon
+ * @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU
+ * @IEEE80211_TX_CTL_INJECTED: Frame was injected, internal to mac80211.
+ * @IEEE80211_TX_STAT_TX_FILTERED: The frame was not transmitted
+ *	because the destination STA was in powersave mode. Note that to
+ *	avoid race conditions, the filter must be set by the hardware or
+ *	firmware upon receiving a frame that indicates that the station
+ *	went to sleep (must be done on device to filter frames already on
+ *	the queue) and may only be unset after mac80211 gives the OK for
+ *	that by setting the IEEE80211_TX_CTL_CLEAR_PS_FILT (see above),
+ *	since only then is it guaranteed that no more frames are in the
+ *	hardware queue.
+ * @IEEE80211_TX_STAT_ACK: Frame was acknowledged
+ * @IEEE80211_TX_STAT_AMPDU: The frame was aggregated, so status
+ * 	is for the whole aggregation.
+ * @IEEE80211_TX_STAT_AMPDU_NO_BACK: no block ack was returned,
+ * 	so consider using block ack request (BAR).
+ * @IEEE80211_TX_CTL_RATE_CTRL_PROBE: internal to mac80211, can be
+ *	set by rate control algorithms to indicate probe rate, will
+ *	be cleared for fragmented frames (except on the last fragment)
+ * @IEEE80211_TX_INTFL_NEED_TXPROCESSING: completely internal to mac80211,
+ *	used to indicate that a pending frame requires TX processing before
+ *	it can be sent out.
+ * @IEEE80211_TX_INTFL_RETRIED: completely internal to mac80211,
+ *	used to indicate that a frame was already retried due to PS
+ * @IEEE80211_TX_INTFL_DONT_ENCRYPT: completely internal to mac80211,
+ *	used to indicate frame should not be encrypted
+ * @IEEE80211_TX_CTL_NO_PS_BUFFER: This frame is a response to a poll
+ *	frame (PS-Poll or uAPSD) or a non-bufferable MMPDU and must
+ *	be sent although the station is in powersave mode.
+ * @IEEE80211_TX_CTL_MORE_FRAMES: More frames will be passed to the
+ *	transmit function after the current frame, this can be used
+ *	by drivers to kick the DMA queue only if unset or when the
+ *	queue gets full.
+ * @IEEE80211_TX_INTFL_RETRANSMISSION: This frame is being retransmitted
+ *	after TX status because the destination was asleep, it must not
+ *	be modified again (no seqno assignment, crypto, etc.)
+ * @IEEE80211_TX_INTFL_NL80211_FRAME_TX: Frame was requested through nl80211
+ *	MLME command (internal to mac80211 to figure out whether to send TX
+ *	status to user space)
+ * @IEEE80211_TX_CTL_LDPC: tells the driver to use LDPC for this frame
+ * @IEEE80211_TX_CTL_STBC: Enables Space-Time Block Coding (STBC) for this
+ *	frame and selects the maximum number of streams that it can use.
+ * @IEEE80211_TX_CTL_TX_OFFCHAN: Marks this packet to be transmitted on
+ *	the off-channel channel when a remain-on-channel offload is done
+ *	in hardware -- normal packets still flow and are expected to be
+ *	handled properly by the device.
+ * @IEEE80211_TX_INTFL_TKIP_MIC_FAILURE: Marks this packet to be used for TKIP
+ *	testing. It will be sent out with incorrect Michael MIC key to allow
+ *	TKIP countermeasures to be tested.
+ * @IEEE80211_TX_CTL_NO_CCK_RATE: This frame will be sent at non CCK rate.
+ *	This flag is actually used for management frame especially for P2P
+ *	frames not being sent at CCK rate in 2GHz band.
+ * @IEEE80211_TX_STATUS_EOSP: This packet marks the end of service period,
+ *	when its status is reported the service period ends. For frames in
+ *	an SP that mac80211 transmits, it is already set; for driver frames
+ *	the driver may set this flag. It is also used to do the same for
+ *	PS-Poll responses.
+ * @IEEE80211_TX_CTL_USE_MINRATE: This frame will be sent at lowest rate.
+ *	This flag is used to send nullfunc frame at minimum rate when
+ *	the nullfunc is used for connection monitoring purpose.
+ * @IEEE80211_TX_CTL_DONTFRAG: Don't fragment this packet even if it
+ *	would be fragmented by size (this is optional, only used for
+ *	monitor injection).
+ *
+ * Note: If you have to add new flags to the enumeration, then don't
+ *	 forget to update %IEEE80211_TX_TEMPORARY_FLAGS when necessary.
+ */
+enum mac80211_tx_control_flags {
+	IEEE80211_TX_CTL_REQ_TX_STATUS		= BIT(0),
+	IEEE80211_TX_CTL_ASSIGN_SEQ		= BIT(1),
+	IEEE80211_TX_CTL_NO_ACK			= BIT(2),
+	IEEE80211_TX_CTL_CLEAR_PS_FILT		= BIT(3),
+	IEEE80211_TX_CTL_FIRST_FRAGMENT		= BIT(4),
+	IEEE80211_TX_CTL_SEND_AFTER_DTIM	= BIT(5),
+	IEEE80211_TX_CTL_AMPDU			= BIT(6),
+	IEEE80211_TX_CTL_INJECTED		= BIT(7),
+	IEEE80211_TX_STAT_TX_FILTERED		= BIT(8),
+	IEEE80211_TX_STAT_ACK			= BIT(9),
+	IEEE80211_TX_STAT_AMPDU			= BIT(10),
+	IEEE80211_TX_STAT_AMPDU_NO_BACK		= BIT(11),
+	IEEE80211_TX_CTL_RATE_CTRL_PROBE	= BIT(12),
+	IEEE80211_TX_INTFL_NEED_TXPROCESSING	= BIT(14),
+	IEEE80211_TX_INTFL_RETRIED		= BIT(15),
+	IEEE80211_TX_INTFL_DONT_ENCRYPT		= BIT(16),
+	IEEE80211_TX_CTL_NO_PS_BUFFER		= BIT(17),
+	IEEE80211_TX_CTL_MORE_FRAMES		= BIT(18),
+	IEEE80211_TX_INTFL_RETRANSMISSION	= BIT(19),
+	/* hole at 20, use later */
+	IEEE80211_TX_INTFL_NL80211_FRAME_TX	= BIT(21),
+	IEEE80211_TX_CTL_LDPC			= BIT(22),
+	IEEE80211_TX_CTL_STBC			= BIT(23) | BIT(24),
+	IEEE80211_TX_CTL_TX_OFFCHAN		= BIT(25),
+	IEEE80211_TX_INTFL_TKIP_MIC_FAILURE	= BIT(26),
+	IEEE80211_TX_CTL_NO_CCK_RATE		= BIT(27),
+	IEEE80211_TX_STATUS_EOSP		= BIT(28),
+	IEEE80211_TX_CTL_USE_MINRATE		= BIT(29),
+	IEEE80211_TX_CTL_DONTFRAG		= BIT(30),
+};
+
+#define IEEE80211_TX_CTL_STBC_SHIFT		23
+
+/*
+ * This definition is used as a mask to clear all temporary flags, which are
+ * set by the tx handlers for each transmission attempt by the mac80211 stack.
+ */
+#define IEEE80211_TX_TEMPORARY_FLAGS (IEEE80211_TX_CTL_NO_ACK |		      \
+	IEEE80211_TX_CTL_CLEAR_PS_FILT | IEEE80211_TX_CTL_FIRST_FRAGMENT |    \
+	IEEE80211_TX_CTL_SEND_AFTER_DTIM | IEEE80211_TX_CTL_AMPDU |	      \
+	IEEE80211_TX_STAT_TX_FILTERED |	IEEE80211_TX_STAT_ACK |		      \
+	IEEE80211_TX_STAT_AMPDU | IEEE80211_TX_STAT_AMPDU_NO_BACK |	      \
+	IEEE80211_TX_CTL_RATE_CTRL_PROBE | IEEE80211_TX_CTL_NO_PS_BUFFER |    \
+	IEEE80211_TX_CTL_MORE_FRAMES | IEEE80211_TX_CTL_LDPC |		      \
+	IEEE80211_TX_CTL_STBC | IEEE80211_TX_STATUS_EOSP)
+
+/**
+ * enum mac80211_rate_control_flags - per-rate flags set by the
+ *	Rate Control algorithm.
+ *
+ * These flags are set by the Rate control algorithm for each rate during tx,
+ * in the @flags member of struct ieee80211_tx_rate.
+ *
+ * @IEEE80211_TX_RC_USE_RTS_CTS: Use RTS/CTS exchange for this rate.
+ * @IEEE80211_TX_RC_USE_CTS_PROTECT: CTS-to-self protection is required.
+ *	This is set if the current BSS requires ERP protection.
+ * @IEEE80211_TX_RC_USE_SHORT_PREAMBLE: Use short preamble.
+ * @IEEE80211_TX_RC_MCS: HT rate.
+ * @IEEE80211_TX_RC_GREEN_FIELD: Indicates whether this rate should be used in
+ *	Greenfield mode.
+ * @IEEE80211_TX_RC_40_MHZ_WIDTH: Indicates if the Channel Width should be 40 MHz.
+ * @IEEE80211_TX_RC_DUP_DATA: The frame should be transmitted on both of the
+ *	adjacent 20 MHz channels, if the current channel type is
+ *	NL80211_CHAN_HT40MINUS or NL80211_CHAN_HT40PLUS.
+ * @IEEE80211_TX_RC_SHORT_GI: Short Guard interval should be used for this rate.
+ */
+enum mac80211_rate_control_flags {
+	IEEE80211_TX_RC_USE_RTS_CTS		= BIT(0),
+	IEEE80211_TX_RC_USE_CTS_PROTECT		= BIT(1),
+	IEEE80211_TX_RC_USE_SHORT_PREAMBLE	= BIT(2),
+
+	/* rate index is an MCS rate number instead of an index */
+	IEEE80211_TX_RC_MCS			= BIT(3),
+	IEEE80211_TX_RC_GREEN_FIELD		= BIT(4),
+	IEEE80211_TX_RC_40_MHZ_WIDTH		= BIT(5),
+	IEEE80211_TX_RC_DUP_DATA		= BIT(6),
+	IEEE80211_TX_RC_SHORT_GI		= BIT(7),
+};
+
+
+/* there are 40 bytes if you don't need the rateset to be kept */
+#define IEEE80211_TX_INFO_DRIVER_DATA_SIZE 40
+
+/* if you do need the rateset, then you have less space */
+#define IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE 24
+
+/* maximum number of rate stages */
+#define IEEE80211_TX_MAX_RATES	5
+
+/**
+ * struct ieee80211_tx_rate - rate selection/status
+ *
+ * @idx: rate index to attempt to send with
+ * @flags: rate control flags (&enum mac80211_rate_control_flags)
+ * @count: number of tries in this rate before going to the next rate
+ *
+ * A value of -1 for @idx indicates an invalid rate and, if used
+ * in an array of retry rates, that no more rates should be tried.
+ *
+ * When used for transmit status reporting, the driver should
+ * always report the rate along with the flags it used.
+ *
+ * &struct ieee80211_tx_info contains an array of these structs
+ * in the control information, and it will be filled by the rate
+ * control algorithm according to what should be sent. For example,
+ * if this array contains, in the format { <idx>, <count> } the
+ * information
+ *    { 3, 2 }, { 2, 2 }, { 1, 4 }, { -1, 0 }, { -1, 0 }
+ * then this means that the frame should be transmitted
+ * up to twice at rate 3, up to twice at rate 2, and up to four
+ * times at rate 1 if it doesn't get acknowledged. Say it gets
+ * acknowledged by the peer after the fifth attempt, the status
+ * information should then contain
+ *   { 3, 2 }, { 2, 2 }, { 1, 1 }, { -1, 0 } ...
+ * since it was transmitted twice at rate 3, twice at rate 2
+ * and once at rate 1 after which we received an acknowledgement.
+ */
+struct ieee80211_tx_rate {
+	s8 idx;
+	u8 count;
+	u8 flags;
+} __packed;
+
+/**
+ * struct ieee80211_tx_info - skb transmit information
+ *
+ * This structure is placed in skb->cb for three uses:
+ *  (1) mac80211 TX control - mac80211 tells the driver what to do
+ *  (2) driver internal use (if applicable)
+ *  (3) TX status information - driver tells mac80211 what happened
+ *
+ * The TX control's sta pointer is only valid during the ->tx call,
+ * it may be NULL.
+ *
+ * @flags: transmit info flags, defined above
+ * @band: the band to transmit on (use for checking for races)
+ * @antenna_sel_tx: antenna to use, 0 for automatic diversity
+ * @ack_frame_id: internal frame ID for TX status, used internally
+ * @control: union for control data
+ * @status: union for status data
+ * @driver_data: array of driver_data pointers
+ * @ampdu_ack_len: number of acked aggregated frames.
+ * 	relevant only if IEEE80211_TX_STAT_AMPDU was set.
+ * @ampdu_len: number of aggregated frames.
+ * 	relevant only if IEEE80211_TX_STAT_AMPDU was set.
+ * @ack_signal: signal strength of the ACK frame
+ */
+struct ieee80211_tx_info {
+	/* common information */
+	u32 flags;
+	u8 band;
+
+	u8 antenna_sel_tx;
+
+	u16 ack_frame_id;
+
+	union {
+		struct {
+			union {
+				/* rate control */
+				struct {
+					struct ieee80211_tx_rate rates[
+						IEEE80211_TX_MAX_RATES];
+					s8 rts_cts_rate_idx;
+				};
+				/* only needed before rate control */
+				unsigned long jiffies;
+			};
+			/* NB: vif can be NULL for injected frames */
+			struct ieee80211_vif *vif;
+			struct ieee80211_key_conf *hw_key;
+			struct ieee80211_sta *sta;
+		} control;
+		struct {
+			struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES];
+			u8 ampdu_ack_len;
+			int ack_signal;
+			u8 ampdu_len;
+			/* 15 bytes free */
+		} status;
+		struct {
+			struct ieee80211_tx_rate driver_rates[
+				IEEE80211_TX_MAX_RATES];
+			void *rate_driver_data[
+				IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE / sizeof(void *)];
+		};
+		void *driver_data[
+			IEEE80211_TX_INFO_DRIVER_DATA_SIZE / sizeof(void *)];
+	};
+};
+
+/**
+ * struct ieee80211_sched_scan_ies - scheduled scan IEs
+ *
+ * This structure is used to pass the appropriate IEs to be used in scheduled
+ * scans for all bands.  It contains both the IEs passed from the userspace
+ * and the ones generated by mac80211.
+ *
+ * @ie: array with the IEs for each supported band
+ * @len: array with the total length of the IEs for each band
+ */
+struct ieee80211_sched_scan_ies {
+	u8 *ie[IEEE80211_NUM_BANDS];
+	size_t len[IEEE80211_NUM_BANDS];
+};
+
+static inline struct ieee80211_tx_info *IEEE80211_SKB_CB(struct sk_buff *skb)
+{
+	return (struct ieee80211_tx_info *)skb->cb;
+}
+
+static inline struct ieee80211_rx_status *IEEE80211_SKB_RXCB(struct sk_buff *skb)
+{
+	return (struct ieee80211_rx_status *)skb->cb;
+}
+
+/**
+ * ieee80211_tx_info_clear_status - clear TX status
+ *
+ * @info: The &struct ieee80211_tx_info to be cleared.
+ *
+ * When the driver passes an skb back to mac80211, it must report
+ * a number of things in TX status. This function clears everything
+ * in the TX status but the rate control information (it does clear
+ * the count since you need to fill that in anyway).
+ *
+ * NOTE: You can only use this function if you do NOT use
+ *	 info->driver_data! Use info->rate_driver_data
+ *	 instead if you need only the less space that allows.
+ */
+static inline void
+ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)
+{
+	int i;
+
+	BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
+		     offsetof(struct ieee80211_tx_info, control.rates));
+	BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
+		     offsetof(struct ieee80211_tx_info, driver_rates));
+	BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8);
+	/* clear the rate counts */
+	for (i = 0; i < IEEE80211_TX_MAX_RATES; i++)
+		info->status.rates[i].count = 0;
+
+	BUILD_BUG_ON(
+	    offsetof(struct ieee80211_tx_info, status.ampdu_ack_len) != 23);
+	memset(&info->status.ampdu_ack_len, 0,
+	       sizeof(struct ieee80211_tx_info) -
+	       offsetof(struct ieee80211_tx_info, status.ampdu_ack_len));
+}
+
+
+/**
+ * enum mac80211_rx_flags - receive flags
+ *
+ * These flags are used with the @flag member of &struct ieee80211_rx_status.
+ * @RX_FLAG_MMIC_ERROR: Michael MIC error was reported on this frame.
+ *	Use together with %RX_FLAG_MMIC_STRIPPED.
+ * @RX_FLAG_DECRYPTED: This frame was decrypted in hardware.
+ * @RX_FLAG_MMIC_STRIPPED: the Michael MIC is stripped off this frame,
+ *	verification has been done by the hardware.
+ * @RX_FLAG_IV_STRIPPED: The IV/ICV are stripped from this frame.
+ *	If this flag is set, the stack cannot do any replay detection
+ *	hence the driver or hardware will have to do that.
+ * @RX_FLAG_FAILED_FCS_CRC: Set this flag if the FCS check failed on
+ *	the frame.
+ * @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on
+ *	the frame.
+ * @RX_FLAG_MACTIME_MPDU: The timestamp passed in the RX status (@mactime
+ *	field) is valid and contains the time the first symbol of the MPDU
+ *	was received. This is useful in monitor mode and for proper IBSS
+ *	merging.
+ * @RX_FLAG_SHORTPRE: Short preamble was used for this frame
+ * @RX_FLAG_HT: HT MCS was used and rate_idx is MCS index
+ * @RX_FLAG_40MHZ: HT40 (40 MHz) was used
+ * @RX_FLAG_SHORT_GI: Short guard interval was used
+ * @RX_FLAG_NO_SIGNAL_VAL: The signal strength value is not present.
+ *	Valid only for data frames (mainly A-MPDU)
+ */
+enum mac80211_rx_flags {
+	RX_FLAG_MMIC_ERROR	= 1<<0,
+	RX_FLAG_DECRYPTED	= 1<<1,
+	RX_FLAG_MMIC_STRIPPED	= 1<<3,
+	RX_FLAG_IV_STRIPPED	= 1<<4,
+	RX_FLAG_FAILED_FCS_CRC	= 1<<5,
+	RX_FLAG_FAILED_PLCP_CRC = 1<<6,
+	RX_FLAG_MACTIME_MPDU	= 1<<7,
+	RX_FLAG_SHORTPRE	= 1<<8,
+	RX_FLAG_HT		= 1<<9,
+	RX_FLAG_40MHZ		= 1<<10,
+	RX_FLAG_SHORT_GI	= 1<<11,
+	RX_FLAG_NO_SIGNAL_VAL	= 1<<12,
+};
+
+/**
+ * struct ieee80211_rx_status - receive status
+ *
+ * The low-level driver should provide this information (the subset
+ * supported by hardware) to the 802.11 code with each received
+ * frame, in the skb's control buffer (cb).
+ *
+ * @mactime: value in microseconds of the 64-bit Time Synchronization Function
+ * 	(TSF) timer when the first data symbol (MPDU) arrived at the hardware.
+ * @band: the active band when this frame was received
+ * @freq: frequency the radio was tuned to when receiving this frame, in MHz
+ * @signal: signal strength when receiving this frame, either in dBm, in dB or
+ *	unspecified depending on the hardware capabilities flags
+ *	@IEEE80211_HW_SIGNAL_*
+ * @antenna: antenna used
+ * @rate_idx: index of data rate into band's supported rates or MCS index if
+ *	HT rates are use (RX_FLAG_HT)
+ * @flag: %RX_FLAG_*
+ * @rx_flags: internal RX flags for mac80211
+ */
+struct ieee80211_rx_status {
+	u64 mactime;
+	enum ieee80211_band band;
+	int freq;
+	int signal;
+	int antenna;
+	int rate_idx;
+	int flag;
+	unsigned int rx_flags;
+};
+
+/**
+ * enum ieee80211_conf_flags - configuration flags
+ *
+ * Flags to define PHY configuration options
+ *
+ * @IEEE80211_CONF_MONITOR: there's a monitor interface present -- use this
+ *	to determine for example whether to calculate timestamps for packets
+ *	or not, do not use instead of filter flags!
+ * @IEEE80211_CONF_PS: Enable 802.11 power save mode (managed mode only).
+ *	This is the power save mode defined by IEEE 802.11-2007 section 11.2,
+ *	meaning that the hardware still wakes up for beacons, is able to
+ *	transmit frames and receive the possible acknowledgment frames.
+ *	Not to be confused with hardware specific wakeup/sleep states,
+ *	driver is responsible for that. See the section "Powersave support"
+ *	for more.
+ * @IEEE80211_CONF_IDLE: The device is running, but idle; if the flag is set
+ *	the driver should be prepared to handle configuration requests but
+ *	may turn the device off as much as possible. Typically, this flag will
+ *	be set when an interface is set UP but not associated or scanning, but
+ *	it can also be unset in that case when monitor interfaces are active.
+ * @IEEE80211_CONF_OFFCHANNEL: The device is currently not on its main
+ *	operating channel.
+ */
+enum ieee80211_conf_flags {
+	IEEE80211_CONF_MONITOR		= (1<<0),
+	IEEE80211_CONF_PS		= (1<<1),
+	IEEE80211_CONF_IDLE		= (1<<2),
+	IEEE80211_CONF_OFFCHANNEL	= (1<<3),
+};
+
+
+/**
+ * enum ieee80211_conf_changed - denotes which configuration changed
+ *
+ * @IEEE80211_CONF_CHANGE_LISTEN_INTERVAL: the listen interval changed
+ * @IEEE80211_CONF_CHANGE_MONITOR: the monitor flag changed
+ * @IEEE80211_CONF_CHANGE_PS: the PS flag or dynamic PS timeout changed
+ * @IEEE80211_CONF_CHANGE_POWER: the TX power changed
+ * @IEEE80211_CONF_CHANGE_CHANNEL: the channel/channel_type changed
+ * @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed
+ * @IEEE80211_CONF_CHANGE_IDLE: Idle flag changed
+ * @IEEE80211_CONF_CHANGE_SMPS: Spatial multiplexing powersave mode changed
+ */
+enum ieee80211_conf_changed {
+	IEEE80211_CONF_CHANGE_SMPS		= BIT(1),
+	IEEE80211_CONF_CHANGE_LISTEN_INTERVAL	= BIT(2),
+	IEEE80211_CONF_CHANGE_MONITOR		= BIT(3),
+	IEEE80211_CONF_CHANGE_PS		= BIT(4),
+	IEEE80211_CONF_CHANGE_POWER		= BIT(5),
+	IEEE80211_CONF_CHANGE_CHANNEL		= BIT(6),
+	IEEE80211_CONF_CHANGE_RETRY_LIMITS	= BIT(7),
+	IEEE80211_CONF_CHANGE_IDLE		= BIT(8),
+};
+
+/**
+ * enum ieee80211_smps_mode - spatial multiplexing power save mode
+ *
+ * @IEEE80211_SMPS_AUTOMATIC: automatic
+ * @IEEE80211_SMPS_OFF: off
+ * @IEEE80211_SMPS_STATIC: static
+ * @IEEE80211_SMPS_DYNAMIC: dynamic
+ * @IEEE80211_SMPS_NUM_MODES: internal, don't use
+ */
+enum ieee80211_smps_mode {
+	IEEE80211_SMPS_AUTOMATIC,
+	IEEE80211_SMPS_OFF,
+	IEEE80211_SMPS_STATIC,
+	IEEE80211_SMPS_DYNAMIC,
+
+	/* keep last */
+	IEEE80211_SMPS_NUM_MODES,
+};
+
+/**
+ * struct ieee80211_conf - configuration of the device
+ *
+ * This struct indicates how the driver shall configure the hardware.
+ *
+ * @flags: configuration flags defined above
+ *
+ * @listen_interval: listen interval in units of beacon interval
+ * @max_sleep_period: the maximum number of beacon intervals to sleep for
+ *	before checking the beacon for a TIM bit (managed mode only); this
+ *	value will be only achievable between DTIM frames, the hardware
+ *	needs to check for the multicast traffic bit in DTIM beacons.
+ *	This variable is valid only when the CONF_PS flag is set.
+ * @ps_dtim_period: The DTIM period of the AP we're connected to, for use
+ *	in power saving. Power saving will not be enabled until a beacon
+ *	has been received and the DTIM period is known.
+ * @dynamic_ps_timeout: The dynamic powersave timeout (in ms), see the
+ *	powersave documentation below. This variable is valid only when
+ *	the CONF_PS flag is set.
+ *
+ * @power_level: requested transmit power (in dBm)
+ *
+ * @channel: the channel to tune to
+ * @channel_type: the channel (HT) type
+ *
+ * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame
+ *    (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
+ *    but actually means the number of transmissions not the number of retries
+ * @short_frame_max_tx_count: Maximum number of transmissions for a "short"
+ *    frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
+ *    number of transmissions not the number of retries
+ *
+ * @smps_mode: spatial multiplexing powersave mode; note that
+ *	%IEEE80211_SMPS_STATIC is used when the device is not
+ *	configured for an HT channel
+ */
+struct ieee80211_conf {
+	u32 flags;
+	int power_level, dynamic_ps_timeout;
+	int max_sleep_period;
+
+	u16 listen_interval;
+	u8 ps_dtim_period;
+
+	u8 long_frame_max_tx_count, short_frame_max_tx_count;
+
+	struct ieee80211_channel *channel;
+	enum nl80211_channel_type channel_type;
+	enum ieee80211_smps_mode smps_mode;
+};
+
+/**
+ * struct ieee80211_channel_switch - holds the channel switch data
+ *
+ * The information provided in this structure is required for channel switch
+ * operation.
+ *
+ * @timestamp: value in microseconds of the 64-bit Time Synchronization
+ *	Function (TSF) timer when the frame containing the channel switch
+ *	announcement was received. This is simply the rx.mactime parameter
+ *	the driver passed into mac80211.
+ * @block_tx: Indicates whether transmission must be blocked before the
+ *	scheduled channel switch, as indicated by the AP.
+ * @channel: the new channel to switch to
+ * @count: the number of TBTT's until the channel switch event
+ */
+struct ieee80211_channel_switch {
+	u64 timestamp;
+	bool block_tx;
+	struct ieee80211_channel *channel;
+	u8 count;
+};
+
+/**
+ * enum ieee80211_vif_flags - virtual interface flags
+ *
+ * @IEEE80211_VIF_BEACON_FILTER: the device performs beacon filtering
+ *	on this virtual interface to avoid unnecessary CPU wakeups
+ * @IEEE80211_VIF_SUPPORTS_CQM_RSSI: the device can do connection quality
+ *	monitoring on this virtual interface -- i.e. it can monitor
+ *	connection quality related parameters, such as the RSSI level and
+ *	provide notifications if configured trigger levels are reached.
+ */
+enum ieee80211_vif_flags {
+	IEEE80211_VIF_BEACON_FILTER		= BIT(0),
+	IEEE80211_VIF_SUPPORTS_CQM_RSSI		= BIT(1),
+};
+
+/**
+ * struct ieee80211_vif - per-interface data
+ *
+ * Data in this structure is continually present for driver
+ * use during the life of a virtual interface.
+ *
+ * @type: type of this virtual interface
+ * @bss_conf: BSS configuration for this interface, either our own
+ *	or the BSS we're associated to
+ * @addr: address of this interface
+ * @p2p: indicates whether this AP or STA interface is a p2p
+ *	interface, i.e. a GO or p2p-sta respectively
+ * @driver_flags: flags/capabilities the driver has for this interface,
+ *	these need to be set (or cleared) when the interface is added
+ *	or, if supported by the driver, the interface type is changed
+ *	at runtime, mac80211 will never touch this field
+ * @drv_priv: data area for driver use, will always be aligned to
+ *	sizeof(void *).
+ */
+struct ieee80211_vif {
+	enum nl80211_iftype type;
+	struct ieee80211_bss_conf bss_conf;
+	u8 addr[ETH_ALEN];
+	bool p2p;
+	u32 driver_flags;
+	/* must be last */
+	u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
+};
+
+static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif)
+{
+#ifdef CONFIG_MAC80211_MESH
+	return vif->type == NL80211_IFTYPE_MESH_POINT;
+#endif
+	return false;
+}
+
+/**
+ * enum ieee80211_key_flags - key flags
+ *
+ * These flags are used for communication about keys between the driver
+ * and mac80211, with the @flags parameter of &struct ieee80211_key_conf.
+ *
+ * @IEEE80211_KEY_FLAG_WMM_STA: Set by mac80211, this flag indicates
+ *	that the STA this key will be used with could be using QoS.
+ * @IEEE80211_KEY_FLAG_GENERATE_IV: This flag should be set by the
+ *	driver to indicate that it requires IV generation for this
+ *	particular key.
+ * @IEEE80211_KEY_FLAG_GENERATE_MMIC: This flag should be set by
+ *	the driver for a TKIP key if it requires Michael MIC
+ *	generation in software.
+ * @IEEE80211_KEY_FLAG_PAIRWISE: Set by mac80211, this flag indicates
+ *	that the key is pairwise rather then a shared key.
+ * @IEEE80211_KEY_FLAG_SW_MGMT: This flag should be set by the driver for a
+ *	CCMP key if it requires CCMP encryption of management frames (MFP) to
+ *	be done in software.
+ * @IEEE80211_KEY_FLAG_PUT_IV_SPACE: This flag should be set by the driver
+ *	for a CCMP key if space should be prepared for the IV, but the IV
+ *	itself should not be generated. Do not set together with
+ *	@IEEE80211_KEY_FLAG_GENERATE_IV on the same key.
+ */
+enum ieee80211_key_flags {
+	IEEE80211_KEY_FLAG_WMM_STA	= 1<<0,
+	IEEE80211_KEY_FLAG_GENERATE_IV	= 1<<1,
+	IEEE80211_KEY_FLAG_GENERATE_MMIC= 1<<2,
+	IEEE80211_KEY_FLAG_PAIRWISE	= 1<<3,
+	IEEE80211_KEY_FLAG_SW_MGMT	= 1<<4,
+	IEEE80211_KEY_FLAG_PUT_IV_SPACE = 1<<5,
+};
+
+/**
+ * struct ieee80211_key_conf - key information
+ *
+ * This key information is given by mac80211 to the driver by
+ * the set_key() callback in &struct ieee80211_ops.
+ *
+ * @hw_key_idx: To be set by the driver, this is the key index the driver
+ *	wants to be given when a frame is transmitted and needs to be
+ *	encrypted in hardware.
+ * @cipher: The key's cipher suite selector.
+ * @flags: key flags, see &enum ieee80211_key_flags.
+ * @keyidx: the key index (0-3)
+ * @keylen: key material length
+ * @key: key material. For ALG_TKIP the key is encoded as a 256-bit (32 byte)
+ * 	data block:
+ * 	- Temporal Encryption Key (128 bits)
+ * 	- Temporal Authenticator Tx MIC Key (64 bits)
+ * 	- Temporal Authenticator Rx MIC Key (64 bits)
+ * @icv_len: The ICV length for this key type
+ * @iv_len: The IV length for this key type
+ */
+struct ieee80211_key_conf {
+	u32 cipher;
+	u8 icv_len;
+	u8 iv_len;
+	u8 hw_key_idx;
+	u8 flags;
+	s8 keyidx;
+	u8 keylen;
+	u8 key[0];
+};
+
+/**
+ * enum set_key_cmd - key command
+ *
+ * Used with the set_key() callback in &struct ieee80211_ops, this
+ * indicates whether a key is being removed or added.
+ *
+ * @SET_KEY: a key is set
+ * @DISABLE_KEY: a key must be disabled
+ */
+enum set_key_cmd {
+	SET_KEY, DISABLE_KEY,
+};
+
+/**
+ * enum ieee80211_sta_state - station state
+ *
+ * @IEEE80211_STA_NOTEXIST: station doesn't exist at all,
+ *	this is a special state for add/remove transitions
+ * @IEEE80211_STA_NONE: station exists without special state
+ * @IEEE80211_STA_AUTH: station is authenticated
+ * @IEEE80211_STA_ASSOC: station is associated
+ * @IEEE80211_STA_AUTHORIZED: station is authorized (802.1X)
+ */
+enum ieee80211_sta_state {
+	/* NOTE: These need to be ordered correctly! */
+	IEEE80211_STA_NOTEXIST,
+	IEEE80211_STA_NONE,
+	IEEE80211_STA_AUTH,
+	IEEE80211_STA_ASSOC,
+	IEEE80211_STA_AUTHORIZED,
+};
+
+/**
+ * struct ieee80211_sta - station table entry
+ *
+ * A station table entry represents a station we are possibly
+ * communicating with. Since stations are RCU-managed in
+ * mac80211, any ieee80211_sta pointer you get access to must
+ * either be protected by rcu_read_lock() explicitly or implicitly,
+ * or you must take good care to not use such a pointer after a
+ * call to your sta_remove callback that removed it.
+ *
+ * @addr: MAC address
+ * @aid: AID we assigned to the station if we're an AP
+ * @supp_rates: Bitmap of supported rates (per band)
+ * @ht_cap: HT capabilities of this STA; restricted to our own TX capabilities
+ * @wme: indicates whether the STA supports WME. Only valid during AP-mode.
+ * @drv_priv: data area for driver use, will always be aligned to
+ *	sizeof(void *), size is determined in hw information.
+ * @uapsd_queues: bitmap of queues configured for uapsd. Only valid
+ *	if wme is supported.
+ * @max_sp: max Service Period. Only valid if wme is supported.
+ */
+struct ieee80211_sta {
+	u32 supp_rates[IEEE80211_NUM_BANDS];
+	u8 addr[ETH_ALEN];
+	u16 aid;
+	struct ieee80211_sta_ht_cap ht_cap;
+	bool wme;
+	u8 uapsd_queues;
+	u8 max_sp;
+
+	/* must be last */
+	u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
+};
+
+/**
+ * enum sta_notify_cmd - sta notify command
+ *
+ * Used with the sta_notify() callback in &struct ieee80211_ops, this
+ * indicates if an associated station made a power state transition.
+ *
+ * @STA_NOTIFY_SLEEP: a station is now sleeping
+ * @STA_NOTIFY_AWAKE: a sleeping station woke up
+ */
+enum sta_notify_cmd {
+	STA_NOTIFY_SLEEP, STA_NOTIFY_AWAKE,
+};
+
+/**
+ * enum ieee80211_hw_flags - hardware flags
+ *
+ * These flags are used to indicate hardware capabilities to
+ * the stack. Generally, flags here should have their meaning
+ * done in a way that the simplest hardware doesn't need setting
+ * any particular flags. There are some exceptions to this rule,
+ * however, so you are advised to review these flags carefully.
+ *
+ * @IEEE80211_HW_HAS_RATE_CONTROL:
+ *	The hardware or firmware includes rate control, and cannot be
+ *	controlled by the stack. As such, no rate control algorithm
+ *	should be instantiated, and the TX rate reported to userspace
+ *	will be taken from the TX status instead of the rate control
+ *	algorithm.
+ *	Note that this requires that the driver implement a number of
+ *	callbacks so it has the correct information, it needs to have
+ *	the @set_rts_threshold callback and must look at the BSS config
+ *	@use_cts_prot for G/N protection, @use_short_slot for slot
+ *	timing in 2.4 GHz and @use_short_preamble for preambles for
+ *	CCK frames.
+ *
+ * @IEEE80211_HW_RX_INCLUDES_FCS:
+ *	Indicates that received frames passed to the stack include
+ *	the FCS at the end.
+ *
+ * @IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING:
+ *	Some wireless LAN chipsets buffer broadcast/multicast frames
+ *	for power saving stations in the hardware/firmware and others
+ *	rely on the host system for such buffering. This option is used
+ *	to configure the IEEE 802.11 upper layer to buffer broadcast and
+ *	multicast frames when there are power saving stations so that
+ *	the driver can fetch them with ieee80211_get_buffered_bc().
+ *
+ * @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE:
+ *	Hardware is not capable of short slot operation on the 2.4 GHz band.
+ *
+ * @IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE:
+ *	Hardware is not capable of receiving frames with short preamble on
+ *	the 2.4 GHz band.
+ *
+ * @IEEE80211_HW_SIGNAL_UNSPEC:
+ *	Hardware can provide signal values but we don't know its units. We
+ *	expect values between 0 and @max_signal.
+ *	If possible please provide dB or dBm instead.
+ *
+ * @IEEE80211_HW_SIGNAL_DBM:
+ *	Hardware gives signal values in dBm, decibel difference from
+ *	one milliwatt. This is the preferred method since it is standardized
+ *	between different devices. @max_signal does not need to be set.
+ *
+ * @IEEE80211_HW_SPECTRUM_MGMT:
+ * 	Hardware supports spectrum management defined in 802.11h
+ * 	Measurement, Channel Switch, Quieting, TPC
+ *
+ * @IEEE80211_HW_AMPDU_AGGREGATION:
+ *	Hardware supports 11n A-MPDU aggregation.
+ *
+ * @IEEE80211_HW_SUPPORTS_PS:
+ *	Hardware has power save support (i.e. can go to sleep).
+ *
+ * @IEEE80211_HW_PS_NULLFUNC_STACK:
+ *	Hardware requires nullfunc frame handling in stack, implies
+ *	stack support for dynamic PS.
+ *
+ * @IEEE80211_HW_SUPPORTS_DYNAMIC_PS:
+ *	Hardware has support for dynamic PS.
+ *
+ * @IEEE80211_HW_MFP_CAPABLE:
+ *	Hardware supports management frame protection (MFP, IEEE 802.11w).
+ *
+ * @IEEE80211_HW_SUPPORTS_STATIC_SMPS:
+ *	Hardware supports static spatial multiplexing powersave,
+ *	ie. can turn off all but one chain even on HT connections
+ *	that should be using more chains.
+ *
+ * @IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS:
+ *	Hardware supports dynamic spatial multiplexing powersave,
+ *	ie. can turn off all but one chain and then wake the rest
+ *	up as required after, for example, rts/cts handshake.
+ *
+ * @IEEE80211_HW_SUPPORTS_UAPSD:
+ *	Hardware supports Unscheduled Automatic Power Save Delivery
+ *	(U-APSD) in managed mode. The mode is configured with
+ *	conf_tx() operation.
+ *
+ * @IEEE80211_HW_REPORTS_TX_ACK_STATUS:
+ *	Hardware can provide ack status reports of Tx frames to
+ *	the stack.
+ *
+ * @IEEE80211_HW_CONNECTION_MONITOR:
+ *      The hardware performs its own connection monitoring, including
+ *      periodic keep-alives to the AP and probing the AP on beacon loss.
+ *      When this flag is set, signaling beacon-loss will cause an immediate
+ *      change to disassociated state.
+ *
+ * @IEEE80211_HW_NEED_DTIM_PERIOD:
+ *	This device needs to know the DTIM period for the BSS before
+ *	associating.
+ *
+ * @IEEE80211_HW_SUPPORTS_PER_STA_GTK: The device's crypto engine supports
+ *	per-station GTKs as used by IBSS RSN or during fast transition. If
+ *	the device doesn't support per-station GTKs, but can be asked not
+ *	to decrypt group addressed frames, then IBSS RSN support is still
+ *	possible but software crypto will be used. Advertise the wiphy flag
+ *	only in that case.
+ *
+ * @IEEE80211_HW_AP_LINK_PS: When operating in AP mode the device
+ *	autonomously manages the PS status of connected stations. When
+ *	this flag is set mac80211 will not trigger PS mode for connected
+ *	stations based on the PM bit of incoming frames.
+ *	Use ieee80211_start_ps()/ieee8021_end_ps() to manually configure
+ *	the PS mode of connected stations.
+ *
+ * @IEEE80211_HW_TX_AMPDU_SETUP_IN_HW: The device handles TX A-MPDU session
+ *	setup strictly in HW. mac80211 should not attempt to do this in
+ *	software.
+ *
+ * @IEEE80211_HW_SCAN_WHILE_IDLE: The device can do hw scan while
+ *	being idle (i.e. mac80211 doesn't have to go idle-off during the
+ *	the scan).
+ */
+enum ieee80211_hw_flags {
+	IEEE80211_HW_HAS_RATE_CONTROL			= 1<<0,
+	IEEE80211_HW_RX_INCLUDES_FCS			= 1<<1,
+	IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING	= 1<<2,
+	IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE		= 1<<3,
+	IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE	= 1<<4,
+	IEEE80211_HW_SIGNAL_UNSPEC			= 1<<5,
+	IEEE80211_HW_SIGNAL_DBM				= 1<<6,
+	IEEE80211_HW_NEED_DTIM_PERIOD			= 1<<7,
+	IEEE80211_HW_SPECTRUM_MGMT			= 1<<8,
+	IEEE80211_HW_AMPDU_AGGREGATION			= 1<<9,
+	IEEE80211_HW_SUPPORTS_PS			= 1<<10,
+	IEEE80211_HW_PS_NULLFUNC_STACK			= 1<<11,
+	IEEE80211_HW_SUPPORTS_DYNAMIC_PS		= 1<<12,
+	IEEE80211_HW_MFP_CAPABLE			= 1<<13,
+	/* reuse bit 14 */
+	IEEE80211_HW_SUPPORTS_STATIC_SMPS		= 1<<15,
+	IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS		= 1<<16,
+	IEEE80211_HW_SUPPORTS_UAPSD			= 1<<17,
+	IEEE80211_HW_REPORTS_TX_ACK_STATUS		= 1<<18,
+	IEEE80211_HW_CONNECTION_MONITOR			= 1<<19,
+	/* reuse bit 20 */
+	IEEE80211_HW_SUPPORTS_PER_STA_GTK		= 1<<21,
+	IEEE80211_HW_AP_LINK_PS				= 1<<22,
+	IEEE80211_HW_TX_AMPDU_SETUP_IN_HW		= 1<<23,
+	IEEE80211_HW_SCAN_WHILE_IDLE			= 1<<24,
+};
+
+/**
+ * struct ieee80211_hw - hardware information and state
+ *
+ * This structure contains the configuration and hardware
+ * information for an 802.11 PHY.
+ *
+ * @wiphy: This points to the &struct wiphy allocated for this
+ *	802.11 PHY. You must fill in the @perm_addr and @dev
+ *	members of this structure using SET_IEEE80211_DEV()
+ *	and SET_IEEE80211_PERM_ADDR(). Additionally, all supported
+ *	bands (with channels, bitrates) are registered here.
+ *
+ * @conf: &struct ieee80211_conf, device configuration, don't use.
+ *
+ * @priv: pointer to private area that was allocated for driver use
+ *	along with this structure.
+ *
+ * @flags: hardware flags, see &enum ieee80211_hw_flags.
+ *
+ * @extra_tx_headroom: headroom to reserve in each transmit skb
+ *	for use by the driver (e.g. for transmit headers.)
+ *
+ * @channel_change_time: time (in microseconds) it takes to change channels.
+ *
+ * @max_signal: Maximum value for signal (rssi) in RX information, used
+ *     only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
+ *
+ * @max_listen_interval: max listen interval in units of beacon interval
+ *     that HW supports
+ *
+ * @queues: number of available hardware transmit queues for
+ *	data packets. WMM/QoS requires at least four, these
+ *	queues need to have configurable access parameters.
+ *
+ * @rate_control_algorithm: rate control algorithm for this hardware.
+ *	If unset (NULL), the default algorithm will be used. Must be
+ *	set before calling ieee80211_register_hw().
+ *
+ * @vif_data_size: size (in bytes) of the drv_priv data area
+ *	within &struct ieee80211_vif.
+ * @sta_data_size: size (in bytes) of the drv_priv data area
+ *	within &struct ieee80211_sta.
+ *
+ * @max_rates: maximum number of alternate rate retry stages the hw
+ *	can handle.
+ * @max_report_rates: maximum number of alternate rate retry stages
+ *	the hw can report back.
+ * @max_rate_tries: maximum number of tries for each stage
+ *
+ * @napi_weight: weight used for NAPI polling.  You must specify an
+ *	appropriate value here if a napi_poll operation is provided
+ *	by your driver.
+ *
+ * @max_rx_aggregation_subframes: maximum buffer size (number of
+ *	sub-frames) to be used for A-MPDU block ack receiver
+ *	aggregation.
+ *	This is only relevant if the device has restrictions on the
+ *	number of subframes, if it relies on mac80211 to do reordering
+ *	it shouldn't be set.
+ *
+ * @max_tx_aggregation_subframes: maximum number of subframes in an
+ *	aggregate an HT driver will transmit, used by the peer as a
+ *	hint to size its reorder buffer.
+ */
+struct ieee80211_hw {
+	struct ieee80211_conf conf;
+	struct wiphy *wiphy;
+	const char *rate_control_algorithm;
+	void *priv;
+	u32 flags;
+	unsigned int extra_tx_headroom;
+	int channel_change_time;
+	int vif_data_size;
+	int sta_data_size;
+	int napi_weight;
+	u16 queues;
+	u16 max_listen_interval;
+	s8 max_signal;
+	u8 max_rates;
+	u8 max_report_rates;
+	u8 max_rate_tries;
+	u8 max_rx_aggregation_subframes;
+	u8 max_tx_aggregation_subframes;
+};
+
+/**
+ * wiphy_to_ieee80211_hw - return a mac80211 driver hw struct from a wiphy
+ *
+ * @wiphy: the &struct wiphy which we want to query
+ *
+ * mac80211 drivers can use this to get to their respective
+ * &struct ieee80211_hw. Drivers wishing to get to their own private
+ * structure can then access it via hw->priv. Note that mac802111 drivers should
+ * not use wiphy_priv() to try to get their private driver structure as this
+ * is already used internally by mac80211.
+ */
+struct ieee80211_hw *wiphy_to_ieee80211_hw(struct wiphy *wiphy);
+
+/**
+ * SET_IEEE80211_DEV - set device for 802.11 hardware
+ *
+ * @hw: the &struct ieee80211_hw to set the device for
+ * @dev: the &struct device of this 802.11 device
+ */
+static inline void SET_IEEE80211_DEV(struct ieee80211_hw *hw, struct device *dev)
+{
+	set_wiphy_dev(hw->wiphy, dev);
+}
+
+/**
+ * SET_IEEE80211_PERM_ADDR - set the permanent MAC address for 802.11 hardware
+ *
+ * @hw: the &struct ieee80211_hw to set the MAC address for
+ * @addr: the address to set
+ */
+static inline void SET_IEEE80211_PERM_ADDR(struct ieee80211_hw *hw, u8 *addr)
+{
+	memcpy(hw->wiphy->perm_addr, addr, ETH_ALEN);
+}
+
+static inline struct ieee80211_rate *
+ieee80211_get_tx_rate(const struct ieee80211_hw *hw,
+		      const struct ieee80211_tx_info *c)
+{
+	if (WARN_ON_ONCE(c->control.rates[0].idx < 0))
+		return NULL;
+	return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[0].idx];
+}
+
+static inline struct ieee80211_rate *
+ieee80211_get_rts_cts_rate(const struct ieee80211_hw *hw,
+			   const struct ieee80211_tx_info *c)
+{
+	if (c->control.rts_cts_rate_idx < 0)
+		return NULL;
+	return &hw->wiphy->bands[c->band]->bitrates[c->control.rts_cts_rate_idx];
+}
+
+static inline struct ieee80211_rate *
+ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw,
+			     const struct ieee80211_tx_info *c, int idx)
+{
+	if (c->control.rates[idx + 1].idx < 0)
+		return NULL;
+	return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[idx + 1].idx];
+}
+
+/**
+ * ieee80211_free_txskb - free TX skb
+ * @hw: the hardware
+ * @skb: the skb
+ *
+ * Free a transmit skb. Use this funtion when some failure
+ * to transmit happened and thus status cannot be reported.
+ */
+void ieee80211_free_txskb(struct ieee80211_hw *hw, struct sk_buff *skb);
+
+/**
+ * DOC: Hardware crypto acceleration
+ *
+ * mac80211 is capable of taking advantage of many hardware
+ * acceleration designs for encryption and decryption operations.
+ *
+ * The set_key() callback in the &struct ieee80211_ops for a given
+ * device is called to enable hardware acceleration of encryption and
+ * decryption. The callback takes a @sta parameter that will be NULL
+ * for default keys or keys used for transmission only, or point to
+ * the station information for the peer for individual keys.
+ * Multiple transmission keys with the same key index may be used when
+ * VLANs are configured for an access point.
+ *
+ * When transmitting, the TX control data will use the @hw_key_idx
+ * selected by the driver by modifying the &struct ieee80211_key_conf
+ * pointed to by the @key parameter to the set_key() function.
+ *
+ * The set_key() call for the %SET_KEY command should return 0 if
+ * the key is now in use, -%EOPNOTSUPP or -%ENOSPC if it couldn't be
+ * added; if you return 0 then hw_key_idx must be assigned to the
+ * hardware key index, you are free to use the full u8 range.
+ *
+ * When the cmd is %DISABLE_KEY then it must succeed.
+ *
+ * Note that it is permissible to not decrypt a frame even if a key
+ * for it has been uploaded to hardware, the stack will not make any
+ * decision based on whether a key has been uploaded or not but rather
+ * based on the receive flags.
+ *
+ * The &struct ieee80211_key_conf structure pointed to by the @key
+ * parameter is guaranteed to be valid until another call to set_key()
+ * removes it, but it can only be used as a cookie to differentiate
+ * keys.
+ *
+ * In TKIP some HW need to be provided a phase 1 key, for RX decryption
+ * acceleration (i.e. iwlwifi). Those drivers should provide update_tkip_key
+ * handler.
+ * The update_tkip_key() call updates the driver with the new phase 1 key.
+ * This happens every time the iv16 wraps around (every 65536 packets). The
+ * set_key() call will happen only once for each key (unless the AP did
+ * rekeying), it will not include a valid phase 1 key. The valid phase 1 key is
+ * provided by update_tkip_key only. The trigger that makes mac80211 call this
+ * handler is software decryption with wrap around of iv16.
+ */
+
+/**
+ * DOC: Powersave support
+ *
+ * mac80211 has support for various powersave implementations.
+ *
+ * First, it can support hardware that handles all powersaving by itself,
+ * such hardware should simply set the %IEEE80211_HW_SUPPORTS_PS hardware
+ * flag. In that case, it will be told about the desired powersave mode
+ * with the %IEEE80211_CONF_PS flag depending on the association status.
+ * The hardware must take care of sending nullfunc frames when necessary,
+ * i.e. when entering and leaving powersave mode. The hardware is required
+ * to look at the AID in beacons and signal to the AP that it woke up when
+ * it finds traffic directed to it.
+ *
+ * %IEEE80211_CONF_PS flag enabled means that the powersave mode defined in
+ * IEEE 802.11-2007 section 11.2 is enabled. This is not to be confused
+ * with hardware wakeup and sleep states. Driver is responsible for waking
+ * up the hardware before issuing commands to the hardware and putting it
+ * back to sleep at appropriate times.
+ *
+ * When PS is enabled, hardware needs to wakeup for beacons and receive the
+ * buffered multicast/broadcast frames after the beacon. Also it must be
+ * possible to send frames and receive the acknowledment frame.
+ *
+ * Other hardware designs cannot send nullfunc frames by themselves and also
+ * need software support for parsing the TIM bitmap. This is also supported
+ * by mac80211 by combining the %IEEE80211_HW_SUPPORTS_PS and
+ * %IEEE80211_HW_PS_NULLFUNC_STACK flags. The hardware is of course still
+ * required to pass up beacons. The hardware is still required to handle
+ * waking up for multicast traffic; if it cannot the driver must handle that
+ * as best as it can, mac80211 is too slow to do that.
+ *
+ * Dynamic powersave is an extension to normal powersave in which the
+ * hardware stays awake for a user-specified period of time after sending a
+ * frame so that reply frames need not be buffered and therefore delayed to
+ * the next wakeup. It's compromise of getting good enough latency when
+ * there's data traffic and still saving significantly power in idle
+ * periods.
+ *
+ * Dynamic powersave is simply supported by mac80211 enabling and disabling
+ * PS based on traffic. Driver needs to only set %IEEE80211_HW_SUPPORTS_PS
+ * flag and mac80211 will handle everything automatically. Additionally,
+ * hardware having support for the dynamic PS feature may set the
+ * %IEEE80211_HW_SUPPORTS_DYNAMIC_PS flag to indicate that it can support
+ * dynamic PS mode itself. The driver needs to look at the
+ * @dynamic_ps_timeout hardware configuration value and use it that value
+ * whenever %IEEE80211_CONF_PS is set. In this case mac80211 will disable
+ * dynamic PS feature in stack and will just keep %IEEE80211_CONF_PS
+ * enabled whenever user has enabled powersave.
+ *
+ * Some hardware need to toggle a single shared antenna between WLAN and
+ * Bluetooth to facilitate co-existence. These types of hardware set
+ * limitations on the use of host controlled dynamic powersave whenever there
+ * is simultaneous WLAN and Bluetooth traffic. For these types of hardware, the
+ * driver may request temporarily going into full power save, in order to
+ * enable toggling the antenna between BT and WLAN. If the driver requests
+ * disabling dynamic powersave, the @dynamic_ps_timeout value will be
+ * temporarily set to zero until the driver re-enables dynamic powersave.
+ *
+ * Driver informs U-APSD client support by enabling
+ * %IEEE80211_HW_SUPPORTS_UAPSD flag. The mode is configured through the
+ * uapsd paramater in conf_tx() operation. Hardware needs to send the QoS
+ * Nullfunc frames and stay awake until the service period has ended. To
+ * utilize U-APSD, dynamic powersave is disabled for voip AC and all frames
+ * from that AC are transmitted with powersave enabled.
+ *
+ * Note: U-APSD client mode is not yet supported with
+ * %IEEE80211_HW_PS_NULLFUNC_STACK.
+ */
+
+/**
+ * DOC: Beacon filter support
+ *
+ * Some hardware have beacon filter support to reduce host cpu wakeups
+ * which will reduce system power consumption. It usually works so that
+ * the firmware creates a checksum of the beacon but omits all constantly
+ * changing elements (TSF, TIM etc). Whenever the checksum changes the
+ * beacon is forwarded to the host, otherwise it will be just dropped. That
+ * way the host will only receive beacons where some relevant information
+ * (for example ERP protection or WMM settings) have changed.
+ *
+ * Beacon filter support is advertised with the %IEEE80211_VIF_BEACON_FILTER
+ * interface capability. The driver needs to enable beacon filter support
+ * whenever power save is enabled, that is %IEEE80211_CONF_PS is set. When
+ * power save is enabled, the stack will not check for beacon loss and the
+ * driver needs to notify about loss of beacons with ieee80211_beacon_loss().
+ *
+ * The time (or number of beacons missed) until the firmware notifies the
+ * driver of a beacon loss event (which in turn causes the driver to call
+ * ieee80211_beacon_loss()) should be configurable and will be controlled
+ * by mac80211 and the roaming algorithm in the future.
+ *
+ * Since there may be constantly changing information elements that nothing
+ * in the software stack cares about, we will, in the future, have mac80211
+ * tell the driver which information elements are interesting in the sense
+ * that we want to see changes in them. This will include
+ *  - a list of information element IDs
+ *  - a list of OUIs for the vendor information element
+ *
+ * Ideally, the hardware would filter out any beacons without changes in the
+ * requested elements, but if it cannot support that it may, at the expense
+ * of some efficiency, filter out only a subset. For example, if the device
+ * doesn't support checking for OUIs it should pass up all changes in all
+ * vendor information elements.
+ *
+ * Note that change, for the sake of simplification, also includes information
+ * elements appearing or disappearing from the beacon.
+ *
+ * Some hardware supports an "ignore list" instead, just make sure nothing
+ * that was requested is on the ignore list, and include commonly changing
+ * information element IDs in the ignore list, for example 11 (BSS load) and
+ * the various vendor-assigned IEs with unknown contents (128, 129, 133-136,
+ * 149, 150, 155, 156, 173, 176, 178, 179, 219); for forward compatibility
+ * it could also include some currently unused IDs.
+ *
+ *
+ * In addition to these capabilities, hardware should support notifying the
+ * host of changes in the beacon RSSI. This is relevant to implement roaming
+ * when no traffic is flowing (when traffic is flowing we see the RSSI of
+ * the received data packets). This can consist in notifying the host when
+ * the RSSI changes significantly or when it drops below or rises above
+ * configurable thresholds. In the future these thresholds will also be
+ * configured by mac80211 (which gets them from userspace) to implement
+ * them as the roaming algorithm requires.
+ *
+ * If the hardware cannot implement this, the driver should ask it to
+ * periodically pass beacon frames to the host so that software can do the
+ * signal strength threshold checking.
+ */
+
+/**
+ * DOC: Spatial multiplexing power save
+ *
+ * SMPS (Spatial multiplexing power save) is a mechanism to conserve
+ * power in an 802.11n implementation. For details on the mechanism
+ * and rationale, please refer to 802.11 (as amended by 802.11n-2009)
+ * "11.2.3 SM power save".
+ *
+ * The mac80211 implementation is capable of sending action frames
+ * to update the AP about the station's SMPS mode, and will instruct
+ * the driver to enter the specific mode. It will also announce the
+ * requested SMPS mode during the association handshake. Hardware
+ * support for this feature is required, and can be indicated by
+ * hardware flags.
+ *
+ * The default mode will be "automatic", which nl80211/cfg80211
+ * defines to be dynamic SMPS in (regular) powersave, and SMPS
+ * turned off otherwise.
+ *
+ * To support this feature, the driver must set the appropriate
+ * hardware support flags, and handle the SMPS flag to the config()
+ * operation. It will then with this mechanism be instructed to
+ * enter the requested SMPS mode while associated to an HT AP.
+ */
+
+/**
+ * DOC: Frame filtering
+ *
+ * mac80211 requires to see many management frames for proper
+ * operation, and users may want to see many more frames when
+ * in monitor mode. However, for best CPU usage and power consumption,
+ * having as few frames as possible percolate through the stack is
+ * desirable. Hence, the hardware should filter as much as possible.
+ *
+ * To achieve this, mac80211 uses filter flags (see below) to tell
+ * the driver's configure_filter() function which frames should be
+ * passed to mac80211 and which should be filtered out.
+ *
+ * Before configure_filter() is invoked, the prepare_multicast()
+ * callback is invoked with the parameters @mc_count and @mc_list
+ * for the combined multicast address list of all virtual interfaces.
+ * It's use is optional, and it returns a u64 that is passed to
+ * configure_filter(). Additionally, configure_filter() has the
+ * arguments @changed_flags telling which flags were changed and
+ * @total_flags with the new flag states.
+ *
+ * If your device has no multicast address filters your driver will
+ * need to check both the %FIF_ALLMULTI flag and the @mc_count
+ * parameter to see whether multicast frames should be accepted
+ * or dropped.
+ *
+ * All unsupported flags in @total_flags must be cleared.
+ * Hardware does not support a flag if it is incapable of _passing_
+ * the frame to the stack. Otherwise the driver must ignore
+ * the flag, but not clear it.
+ * You must _only_ clear the flag (announce no support for the
+ * flag to mac80211) if you are not able to pass the packet type
+ * to the stack (so the hardware always filters it).
+ * So for example, you should clear @FIF_CONTROL, if your hardware
+ * always filters control frames. If your hardware always passes
+ * control frames to the kernel and is incapable of filtering them,
+ * you do _not_ clear the @FIF_CONTROL flag.
+ * This rule applies to all other FIF flags as well.
+ */
+
+/**
+ * DOC: AP support for powersaving clients
+ *
+ * In order to implement AP and P2P GO modes, mac80211 has support for
+ * client powersaving, both "legacy" PS (PS-Poll/null data) and uAPSD.
+ * There currently is no support for sAPSD.
+ *
+ * There is one assumption that mac80211 makes, namely that a client
+ * will not poll with PS-Poll and trigger with uAPSD at the same time.
+ * Both are supported, and both can be used by the same client, but
+ * they can't be used concurrently by the same client. This simplifies
+ * the driver code.
+ *
+ * The first thing to keep in mind is that there is a flag for complete
+ * driver implementation: %IEEE80211_HW_AP_LINK_PS. If this flag is set,
+ * mac80211 expects the driver to handle most of the state machine for
+ * powersaving clients and will ignore the PM bit in incoming frames.
+ * Drivers then use ieee80211_sta_ps_transition() to inform mac80211 of
+ * stations' powersave transitions. In this mode, mac80211 also doesn't
+ * handle PS-Poll/uAPSD.
+ *
+ * In the mode without %IEEE80211_HW_AP_LINK_PS, mac80211 will check the
+ * PM bit in incoming frames for client powersave transitions. When a
+ * station goes to sleep, we will stop transmitting to it. There is,
+ * however, a race condition: a station might go to sleep while there is
+ * data buffered on hardware queues. If the device has support for this
+ * it will reject frames, and the driver should give the frames back to
+ * mac80211 with the %IEEE80211_TX_STAT_TX_FILTERED flag set which will
+ * cause mac80211 to retry the frame when the station wakes up. The
+ * driver is also notified of powersave transitions by calling its
+ * @sta_notify callback.
+ *
+ * When the station is asleep, it has three choices: it can wake up,
+ * it can PS-Poll, or it can possibly start a uAPSD service period.
+ * Waking up is implemented by simply transmitting all buffered (and
+ * filtered) frames to the station. This is the easiest case. When
+ * the station sends a PS-Poll or a uAPSD trigger frame, mac80211
+ * will inform the driver of this with the @allow_buffered_frames
+ * callback; this callback is optional. mac80211 will then transmit
+ * the frames as usual and set the %IEEE80211_TX_CTL_NO_PS_BUFFER
+ * on each frame. The last frame in the service period (or the only
+ * response to a PS-Poll) also has %IEEE80211_TX_STATUS_EOSP set to
+ * indicate that it ends the service period; as this frame must have
+ * TX status report it also sets %IEEE80211_TX_CTL_REQ_TX_STATUS.
+ * When TX status is reported for this frame, the service period is
+ * marked has having ended and a new one can be started by the peer.
+ *
+ * Additionally, non-bufferable MMPDUs can also be transmitted by
+ * mac80211 with the %IEEE80211_TX_CTL_NO_PS_BUFFER set in them.
+ *
+ * Another race condition can happen on some devices like iwlwifi
+ * when there are frames queued for the station and it wakes up
+ * or polls; the frames that are already queued could end up being
+ * transmitted first instead, causing reordering and/or wrong
+ * processing of the EOSP. The cause is that allowing frames to be
+ * transmitted to a certain station is out-of-band communication to
+ * the device. To allow this problem to be solved, the driver can
+ * call ieee80211_sta_block_awake() if frames are buffered when it
+ * is notified that the station went to sleep. When all these frames
+ * have been filtered (see above), it must call the function again
+ * to indicate that the station is no longer blocked.
+ *
+ * If the driver buffers frames in the driver for aggregation in any
+ * way, it must use the ieee80211_sta_set_buffered() call when it is
+ * notified of the station going to sleep to inform mac80211 of any
+ * TIDs that have frames buffered. Note that when a station wakes up
+ * this information is reset (hence the requirement to call it when
+ * informed of the station going to sleep). Then, when a service
+ * period starts for any reason, @release_buffered_frames is called
+ * with the number of frames to be released and which TIDs they are
+ * to come from. In this case, the driver is responsible for setting
+ * the EOSP (for uAPSD) and MORE_DATA bits in the released frames,
+ * to help the @more_data paramter is passed to tell the driver if
+ * there is more data on other TIDs -- the TIDs to release frames
+ * from are ignored since mac80211 doesn't know how many frames the
+ * buffers for those TIDs contain.
+ *
+ * If the driver also implement GO mode, where absence periods may
+ * shorten service periods (or abort PS-Poll responses), it must
+ * filter those response frames except in the case of frames that
+ * are buffered in the driver -- those must remain buffered to avoid
+ * reordering. Because it is possible that no frames are released
+ * in this case, the driver must call ieee80211_sta_eosp_irqsafe()
+ * to indicate to mac80211 that the service period ended anyway.
+ *
+ * Finally, if frames from multiple TIDs are released from mac80211
+ * but the driver might reorder them, it must clear & set the flags
+ * appropriately (only the last frame may have %IEEE80211_TX_STATUS_EOSP)
+ * and also take care of the EOSP and MORE_DATA bits in the frame.
+ * The driver may also use ieee80211_sta_eosp_irqsafe() in this case.
+ */
+
+/**
+ * enum ieee80211_filter_flags - hardware filter flags
+ *
+ * These flags determine what the filter in hardware should be
+ * programmed to let through and what should not be passed to the
+ * stack. It is always safe to pass more frames than requested,
+ * but this has negative impact on power consumption.
+ *
+ * @FIF_PROMISC_IN_BSS: promiscuous mode within your BSS,
+ *	think of the BSS as your network segment and then this corresponds
+ *	to the regular ethernet device promiscuous mode.
+ *
+ * @FIF_ALLMULTI: pass all multicast frames, this is used if requested
+ *	by the user or if the hardware is not capable of filtering by
+ *	multicast address.
+ *
+ * @FIF_FCSFAIL: pass frames with failed FCS (but you need to set the
+ *	%RX_FLAG_FAILED_FCS_CRC for them)
+ *
+ * @FIF_PLCPFAIL: pass frames with failed PLCP CRC (but you need to set
+ *	the %RX_FLAG_FAILED_PLCP_CRC for them
+ *
+ * @FIF_BCN_PRBRESP_PROMISC: This flag is set during scanning to indicate
+ *	to the hardware that it should not filter beacons or probe responses
+ *	by BSSID. Filtering them can greatly reduce the amount of processing
+ *	mac80211 needs to do and the amount of CPU wakeups, so you should
+ *	honour this flag if possible.
+ *
+ * @FIF_CONTROL: pass control frames (except for PS Poll), if PROMISC_IN_BSS
+ * 	is not set then only those addressed to this station.
+ *
+ * @FIF_OTHER_BSS: pass frames destined to other BSSes
+ *
+ * @FIF_PSPOLL: pass PS Poll frames, if PROMISC_IN_BSS is not set then only
+ * 	those addressed to this station.
+ *
+ * @FIF_PROBE_REQ: pass probe request frames
+ */
+enum ieee80211_filter_flags {
+	FIF_PROMISC_IN_BSS	= 1<<0,
+	FIF_ALLMULTI		= 1<<1,
+	FIF_FCSFAIL		= 1<<2,
+	FIF_PLCPFAIL		= 1<<3,
+	FIF_BCN_PRBRESP_PROMISC	= 1<<4,
+	FIF_CONTROL		= 1<<5,
+	FIF_OTHER_BSS		= 1<<6,
+	FIF_PSPOLL		= 1<<7,
+	FIF_PROBE_REQ		= 1<<8,
+};
+
+/**
+ * enum ieee80211_ampdu_mlme_action - A-MPDU actions
+ *
+ * These flags are used with the ampdu_action() callback in
+ * &struct ieee80211_ops to indicate which action is needed.
+ *
+ * Note that drivers MUST be able to deal with a TX aggregation
+ * session being stopped even before they OK'ed starting it by
+ * calling ieee80211_start_tx_ba_cb_irqsafe, because the peer
+ * might receive the addBA frame and send a delBA right away!
+ *
+ * @IEEE80211_AMPDU_RX_START: start Rx aggregation
+ * @IEEE80211_AMPDU_RX_STOP: stop Rx aggregation
+ * @IEEE80211_AMPDU_TX_START: start Tx aggregation
+ * @IEEE80211_AMPDU_TX_STOP: stop Tx aggregation
+ * @IEEE80211_AMPDU_TX_OPERATIONAL: TX aggregation has become operational
+ */
+enum ieee80211_ampdu_mlme_action {
+	IEEE80211_AMPDU_RX_START,
+	IEEE80211_AMPDU_RX_STOP,
+	IEEE80211_AMPDU_TX_START,
+	IEEE80211_AMPDU_TX_STOP,
+	IEEE80211_AMPDU_TX_OPERATIONAL,
+};
+
+/**
+ * enum ieee80211_frame_release_type - frame release reason
+ * @IEEE80211_FRAME_RELEASE_PSPOLL: frame released for PS-Poll
+ * @IEEE80211_FRAME_RELEASE_UAPSD: frame(s) released due to
+ *	frame received on trigger-enabled AC
+ */
+enum ieee80211_frame_release_type {
+	IEEE80211_FRAME_RELEASE_PSPOLL,
+	IEEE80211_FRAME_RELEASE_UAPSD,
+};
+
+/**
+ * struct ieee80211_ops - callbacks from mac80211 to the driver
+ *
+ * This structure contains various callbacks that the driver may
+ * handle or, in some cases, must handle, for example to configure
+ * the hardware to a new channel or to transmit a frame.
+ *
+ * @tx: Handler that 802.11 module calls for each transmitted frame.
+ *	skb contains the buffer starting from the IEEE 802.11 header.
+ *	The low-level driver should send the frame out based on
+ *	configuration in the TX control data. This handler should,
+ *	preferably, never fail and stop queues appropriately.
+ *	This must be implemented if @tx_frags is not.
+ *	Must be atomic.
+ *
+ * @tx_frags: Called to transmit multiple fragments of a single MSDU.
+ *	This handler must consume all fragments, sending out some of
+ *	them only is useless and it can't ask for some of them to be
+ *	queued again. If the frame is not fragmented the queue has a
+ *	single SKB only. To avoid issues with the networking stack
+ *	when TX status is reported the frames should be removed from
+ *	the skb queue.
+ *	If this is used, the tx_info @vif and @sta pointers will be
+ *	invalid -- you must not use them in that case.
+ *	This must be implemented if @tx isn't.
+ *	Must be atomic.
+ *
+ * @start: Called before the first netdevice attached to the hardware
+ *	is enabled. This should turn on the hardware and must turn on
+ *	frame reception (for possibly enabled monitor interfaces.)
+ *	Returns negative error codes, these may be seen in userspace,
+ *	or zero.
+ *	When the device is started it should not have a MAC address
+ *	to avoid acknowledging frames before a non-monitor device
+ *	is added.
+ *	Must be implemented and can sleep.
+ *
+ * @stop: Called after last netdevice attached to the hardware
+ *	is disabled. This should turn off the hardware (at least
+ *	it must turn off frame reception.)
+ *	May be called right after add_interface if that rejects
+ *	an interface. If you added any work onto the mac80211 workqueue
+ *	you should ensure to cancel it on this callback.
+ *	Must be implemented and can sleep.
+ *
+ * @suspend: Suspend the device; mac80211 itself will quiesce before and
+ *	stop transmitting and doing any other configuration, and then
+ *	ask the device to suspend. This is only invoked when WoWLAN is
+ *	configured, otherwise the device is deconfigured completely and
+ *	reconfigured at resume time.
+ *	The driver may also impose special conditions under which it
+ *	wants to use the "normal" suspend (deconfigure), say if it only
+ *	supports WoWLAN when the device is associated. In this case, it
+ *	must return 1 from this function.
+ *
+ * @resume: If WoWLAN was configured, this indicates that mac80211 is
+ *	now resuming its operation, after this the device must be fully
+ *	functional again. If this returns an error, the only way out is
+ *	to also unregister the device. If it returns 1, then mac80211
+ *	will also go through the regular complete restart on resume.
+ *
+ * @add_interface: Called when a netdevice attached to the hardware is
+ *	enabled. Because it is not called for monitor mode devices, @start
+ *	and @stop must be implemented.
+ *	The driver should perform any initialization it needs before
+ *	the device can be enabled. The initial configuration for the
+ *	interface is given in the conf parameter.
+ *	The callback may refuse to add an interface by returning a
+ *	negative error code (which will be seen in userspace.)
+ *	Must be implemented and can sleep.
+ *
+ * @change_interface: Called when a netdevice changes type. This callback
+ *	is optional, but only if it is supported can interface types be
+ *	switched while the interface is UP. The callback may sleep.
+ *	Note that while an interface is being switched, it will not be
+ *	found by the interface iteration callbacks.
+ *
+ * @remove_interface: Notifies a driver that an interface is going down.
+ *	The @stop callback is called after this if it is the last interface
+ *	and no monitor interfaces are present.
+ *	When all interfaces are removed, the MAC address in the hardware
+ *	must be cleared so the device no longer acknowledges packets,
+ *	the mac_addr member of the conf structure is, however, set to the
+ *	MAC address of the device going away.
+ *	Hence, this callback must be implemented. It can sleep.
+ *
+ * @config: Handler for configuration requests. IEEE 802.11 code calls this
+ *	function to change hardware configuration, e.g., channel.
+ *	This function should never fail but returns a negative error code
+ *	if it does. The callback can sleep.
+ *
+ * @bss_info_changed: Handler for configuration requests related to BSS
+ *	parameters that may vary during BSS's lifespan, and may affect low
+ *	level driver (e.g. assoc/disassoc status, erp parameters).
+ *	This function should not be used if no BSS has been set, unless
+ *	for association indication. The @changed parameter indicates which
+ *	of the bss parameters has changed when a call is made. The callback
+ *	can sleep.
+ *
+ * @prepare_multicast: Prepare for multicast filter configuration.
+ *	This callback is optional, and its return value is passed
+ *	to configure_filter(). This callback must be atomic.
+ *
+ * @configure_filter: Configure the device's RX filter.
+ *	See the section "Frame filtering" for more information.
+ *	This callback must be implemented and can sleep.
+ *
+ * @set_tim: Set TIM bit. mac80211 calls this function when a TIM bit
+ * 	must be set or cleared for a given STA. Must be atomic.
+ *
+ * @set_key: See the section "Hardware crypto acceleration"
+ *	This callback is only called between add_interface and
+ *	remove_interface calls, i.e. while the given virtual interface
+ *	is enabled.
+ *	Returns a negative error code if the key can't be added.
+ *	The callback can sleep.
+ *
+ * @update_tkip_key: See the section "Hardware crypto acceleration"
+ * 	This callback will be called in the context of Rx. Called for drivers
+ * 	which set IEEE80211_KEY_FLAG_TKIP_REQ_RX_P1_KEY.
+ *	The callback must be atomic.
+ *
+ * @set_rekey_data: If the device supports GTK rekeying, for example while the
+ *	host is suspended, it can assign this callback to retrieve the data
+ *	necessary to do GTK rekeying, this is the KEK, KCK and replay counter.
+ *	After rekeying was done it should (for example during resume) notify
+ *	userspace of the new replay counter using ieee80211_gtk_rekey_notify().
+ *
+ * @hw_scan: Ask the hardware to service the scan request, no need to start
+ *	the scan state machine in stack. The scan must honour the channel
+ *	configuration done by the regulatory agent in the wiphy's
+ *	registered bands. The hardware (or the driver) needs to make sure
+ *	that power save is disabled.
+ *	The @req ie/ie_len members are rewritten by mac80211 to contain the
+ *	entire IEs after the SSID, so that drivers need not look at these
+ *	at all but just send them after the SSID -- mac80211 includes the
+ *	(extended) supported rates and HT information (where applicable).
+ *	When the scan finishes, ieee80211_scan_completed() must be called;
+ *	note that it also must be called when the scan cannot finish due to
+ *	any error unless this callback returned a negative error code.
+ *	The callback can sleep.
+ *
+ * @cancel_hw_scan: Ask the low-level tp cancel the active hw scan.
+ *	The driver should ask the hardware to cancel the scan (if possible),
+ *	but the scan will be completed only after the driver will call
+ *	ieee80211_scan_completed().
+ *	This callback is needed for wowlan, to prevent enqueueing a new
+ *	scan_work after the low-level driver was already suspended.
+ *	The callback can sleep.
+ *
+ * @sched_scan_start: Ask the hardware to start scanning repeatedly at
+ *	specific intervals.  The driver must call the
+ *	ieee80211_sched_scan_results() function whenever it finds results.
+ *	This process will continue until sched_scan_stop is called.
+ *
+ * @sched_scan_stop: Tell the hardware to stop an ongoing scheduled scan.
+ *
+ * @sw_scan_start: Notifier function that is called just before a software scan
+ *	is started. Can be NULL, if the driver doesn't need this notification.
+ *	The callback can sleep.
+ *
+ * @sw_scan_complete: Notifier function that is called just after a
+ *	software scan finished. Can be NULL, if the driver doesn't need
+ *	this notification.
+ *	The callback can sleep.
+ *
+ * @get_stats: Return low-level statistics.
+ * 	Returns zero if statistics are available.
+ *	The callback can sleep.
+ *
+ * @get_tkip_seq: If your device implements TKIP encryption in hardware this
+ *	callback should be provided to read the TKIP transmit IVs (both IV32
+ *	and IV16) for the given key from hardware.
+ *	The callback must be atomic.
+ *
+ * @set_frag_threshold: Configuration of fragmentation threshold. Assign this
+ *	if the device does fragmentation by itself; if this callback is
+ *	implemented then the stack will not do fragmentation.
+ *	The callback can sleep.
+ *
+ * @set_rts_threshold: Configuration of RTS threshold (if device needs it)
+ *	The callback can sleep.
+ *
+ * @sta_add: Notifies low level driver about addition of an associated station,
+ *	AP, IBSS/WDS/mesh peer etc. This callback can sleep.
+ *
+ * @sta_remove: Notifies low level driver about removal of an associated
+ *	station, AP, IBSS/WDS/mesh peer etc. This callback can sleep.
+ *
+ * @sta_notify: Notifies low level driver about power state transition of an
+ *	associated station, AP,  IBSS/WDS/mesh peer etc. For a VIF operating
+ *	in AP mode, this callback will not be called when the flag
+ *	%IEEE80211_HW_AP_LINK_PS is set. Must be atomic.
+ *
+ * @sta_state: Notifies low level driver about state transition of a
+ *	station (which can be the AP, a client, IBSS/WDS/mesh peer etc.)
+ *	This callback is mutually exclusive with @sta_add/@sta_remove.
+ *	It must not fail for down transitions but may fail for transitions
+ *	up the list of states.
+ *	The callback can sleep.
+ *
+ * @conf_tx: Configure TX queue parameters (EDCF (aifs, cw_min, cw_max),
+ *	bursting) for a hardware TX queue.
+ *	Returns a negative error code on failure.
+ *	The callback can sleep.
+ *
+ * @get_tsf: Get the current TSF timer value from firmware/hardware. Currently,
+ *	this is only used for IBSS mode BSSID merging and debugging. Is not a
+ *	required function.
+ *	The callback can sleep.
+ *
+ * @set_tsf: Set the TSF timer to the specified value in the firmware/hardware.
+ *      Currently, this is only used for IBSS mode debugging. Is not a
+ *	required function.
+ *	The callback can sleep.
+ *
+ * @reset_tsf: Reset the TSF timer and allow firmware/hardware to synchronize
+ *	with other STAs in the IBSS. This is only used in IBSS mode. This
+ *	function is optional if the firmware/hardware takes full care of
+ *	TSF synchronization.
+ *	The callback can sleep.
+ *
+ * @tx_last_beacon: Determine whether the last IBSS beacon was sent by us.
+ *	This is needed only for IBSS mode and the result of this function is
+ *	used to determine whether to reply to Probe Requests.
+ *	Returns non-zero if this device sent the last beacon.
+ *	The callback can sleep.
+ *
+ * @ampdu_action: Perform a certain A-MPDU action
+ * 	The RA/TID combination determines the destination and TID we want
+ * 	the ampdu action to be performed for. The action is defined through
+ * 	ieee80211_ampdu_mlme_action. Starting sequence number (@ssn)
+ * 	is the first frame we expect to perform the action on. Notice
+ * 	that TX/RX_STOP can pass NULL for this parameter.
+ *	The @buf_size parameter is only valid when the action is set to
+ *	%IEEE80211_AMPDU_TX_OPERATIONAL and indicates the peer's reorder
+ *	buffer size (number of subframes) for this session -- the driver
+ *	may neither send aggregates containing more subframes than this
+ *	nor send aggregates in a way that lost frames would exceed the
+ *	buffer size. If just limiting the aggregate size, this would be
+ *	possible with a buf_size of 8:
+ *	 - TX: 1.....7
+ *	 - RX:  2....7 (lost frame #1)
+ *	 - TX:        8..1...
+ *	which is invalid since #1 was now re-transmitted well past the
+ *	buffer size of 8. Correct ways to retransmit #1 would be:
+ *	 - TX:       1 or 18 or 81
+ *	Even "189" would be wrong since 1 could be lost again.
+ *
+ *	Returns a negative error code on failure.
+ *	The callback can sleep.
+ *
+ * @get_survey: Return per-channel survey information
+ *
+ * @rfkill_poll: Poll rfkill hardware state. If you need this, you also
+ *	need to set wiphy->rfkill_poll to %true before registration,
+ *	and need to call wiphy_rfkill_set_hw_state() in the callback.
+ *	The callback can sleep.
+ *
+ * @set_coverage_class: Set slot time for given coverage class as specified
+ *	in IEEE 802.11-2007 section 17.3.8.6 and modify ACK timeout
+ *	accordingly. This callback is not required and may sleep.
+ *
+ * @testmode_cmd: Implement a cfg80211 test mode command.
+ *	The callback can sleep.
+ * @testmode_dump: Implement a cfg80211 test mode dump. The callback can sleep.
+ *
+ * @flush: Flush all pending frames from the hardware queue, making sure
+ *	that the hardware queues are empty. If the parameter @drop is set
+ *	to %true, pending frames may be dropped. The callback can sleep.
+ *
+ * @channel_switch: Drivers that need (or want) to offload the channel
+ *	switch operation for CSAs received from the AP may implement this
+ *	callback. They must then call ieee80211_chswitch_done() to indicate
+ *	completion of the channel switch.
+ *
+ * @napi_poll: Poll Rx queue for incoming data frames.
+ *
+ * @set_antenna: Set antenna configuration (tx_ant, rx_ant) on the device.
+ *	Parameters are bitmaps of allowed antennas to use for TX/RX. Drivers may
+ *	reject TX/RX mask combinations they cannot support by returning -EINVAL
+ *	(also see nl80211.h @NL80211_ATTR_WIPHY_ANTENNA_TX).
+ *
+ * @get_antenna: Get current antenna configuration from device (tx_ant, rx_ant).
+ *
+ * @remain_on_channel: Starts an off-channel period on the given channel, must
+ *	call back to ieee80211_ready_on_channel() when on that channel. Note
+ *	that normal channel traffic is not stopped as this is intended for hw
+ *	offload. Frames to transmit on the off-channel channel are transmitted
+ *	normally except for the %IEEE80211_TX_CTL_TX_OFFCHAN flag. When the
+ *	duration (which will always be non-zero) expires, the driver must call
+ *	ieee80211_remain_on_channel_expired(). This callback may sleep.
+ * @cancel_remain_on_channel: Requests that an ongoing off-channel period is
+ *	aborted before it expires. This callback may sleep.
+ *
+ * @set_ringparam: Set tx and rx ring sizes.
+ *
+ * @get_ringparam: Get tx and rx ring current and maximum sizes.
+ *
+ * @tx_frames_pending: Check if there is any pending frame in the hardware
+ *	queues before entering power save.
+ *
+ * @set_bitrate_mask: Set a mask of rates to be used for rate control selection
+ *	when transmitting a frame. Currently only legacy rates are handled.
+ *	The callback can sleep.
+ * @rssi_callback: Notify driver when the average RSSI goes above/below
+ *	thresholds that were registered previously. The callback can sleep.
+ *
+ * @release_buffered_frames: Release buffered frames according to the given
+ *	parameters. In the case where the driver buffers some frames for
+ *	sleeping stations mac80211 will use this callback to tell the driver
+ *	to release some frames, either for PS-poll or uAPSD.
+ *	Note that if the @more_data paramter is %false the driver must check
+ *	if there are more frames on the given TIDs, and if there are more than
+ *	the frames being released then it must still set the more-data bit in
+ *	the frame. If the @more_data parameter is %true, then of course the
+ *	more-data bit must always be set.
+ *	The @tids parameter tells the driver which TIDs to release frames
+ *	from, for PS-poll it will always have only a single bit set.
+ *	In the case this is used for a PS-poll initiated release, the
+ *	@num_frames parameter will always be 1 so code can be shared. In
+ *	this case the driver must also set %IEEE80211_TX_STATUS_EOSP flag
+ *	on the TX status (and must report TX status) so that the PS-poll
+ *	period is properly ended. This is used to avoid sending multiple
+ *	responses for a retried PS-poll frame.
+ *	In the case this is used for uAPSD, the @num_frames parameter may be
+ *	bigger than one, but the driver may send fewer frames (it must send
+ *	at least one, however). In this case it is also responsible for
+ *	setting the EOSP flag in the QoS header of the frames. Also, when the
+ *	service period ends, the driver must set %IEEE80211_TX_STATUS_EOSP
+ *	on the last frame in the SP. Alternatively, it may call the function
+ *	ieee80211_sta_eosp_irqsafe() to inform mac80211 of the end of the SP.
+ *	This callback must be atomic.
+ * @allow_buffered_frames: Prepare device to allow the given number of frames
+ *	to go out to the given station. The frames will be sent by mac80211
+ *	via the usual TX path after this call. The TX information for frames
+ *	released will also have the %IEEE80211_TX_CTL_NO_PS_BUFFER flag set
+ *	and the last one will also have %IEEE80211_TX_STATUS_EOSP set. In case
+ *	frames from multiple TIDs are released and the driver might reorder
+ *	them between the TIDs, it must set the %IEEE80211_TX_STATUS_EOSP flag
+ *	on the last frame and clear it on all others and also handle the EOSP
+ *	bit in the QoS header correctly. Alternatively, it can also call the
+ *	ieee80211_sta_eosp_irqsafe() function.
+ *	The @tids parameter is a bitmap and tells the driver which TIDs the
+ *	frames will be on; it will at most have two bits set.
+ *	This callback must be atomic.
+ */
+struct ieee80211_ops {
+	void (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb);
+	void (*tx_frags)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
+			 struct ieee80211_sta *sta, struct sk_buff_head *skbs);
+	int (*start)(struct ieee80211_hw *hw);
+	void (*stop)(struct ieee80211_hw *hw);
+#ifdef CONFIG_PM
+	int (*suspend)(struct ieee80211_hw *hw, struct cfg80211_wowlan *wowlan);
+	int (*resume)(struct ieee80211_hw *hw);
+#endif
+	int (*add_interface)(struct ieee80211_hw *hw,
+			     struct ieee80211_vif *vif);
+	int (*change_interface)(struct ieee80211_hw *hw,
+				struct ieee80211_vif *vif,
+				enum nl80211_iftype new_type, bool p2p);
+	void (*remove_interface)(struct ieee80211_hw *hw,
+				 struct ieee80211_vif *vif);
+	int (*config)(struct ieee80211_hw *hw, u32 changed);
+	void (*bss_info_changed)(struct ieee80211_hw *hw,
+				 struct ieee80211_vif *vif,
+				 struct ieee80211_bss_conf *info,
+				 u32 changed);
+
+	u64 (*prepare_multicast)(struct ieee80211_hw *hw,
+				 struct netdev_hw_addr_list *mc_list);
+	void (*configure_filter)(struct ieee80211_hw *hw,
+				 unsigned int changed_flags,
+				 unsigned int *total_flags,
+				 u64 multicast);
+	int (*set_tim)(struct ieee80211_hw *hw, struct ieee80211_sta *sta,
+		       bool set);
+	int (*set_key)(struct ieee80211_hw *hw, enum set_key_cmd cmd,
+		       struct ieee80211_vif *vif, struct ieee80211_sta *sta,
+		       struct ieee80211_key_conf *key);
+	void (*update_tkip_key)(struct ieee80211_hw *hw,
+				struct ieee80211_vif *vif,
+				struct ieee80211_key_conf *conf,
+				struct ieee80211_sta *sta,
+				u32 iv32, u16 *phase1key);
+	void (*set_rekey_data)(struct ieee80211_hw *hw,
+			       struct ieee80211_vif *vif,
+			       struct cfg80211_gtk_rekey_data *data);
+	int (*hw_scan)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
+		       struct cfg80211_scan_request *req);
+	void (*cancel_hw_scan)(struct ieee80211_hw *hw,
+			       struct ieee80211_vif *vif);
+	int (*sched_scan_start)(struct ieee80211_hw *hw,
+				struct ieee80211_vif *vif,
+				struct cfg80211_sched_scan_request *req,
+				struct ieee80211_sched_scan_ies *ies);
+	void (*sched_scan_stop)(struct ieee80211_hw *hw,
+			       struct ieee80211_vif *vif);
+	void (*sw_scan_start)(struct ieee80211_hw *hw);
+	void (*sw_scan_complete)(struct ieee80211_hw *hw);
+	int (*get_stats)(struct ieee80211_hw *hw,
+			 struct ieee80211_low_level_stats *stats);
+	void (*get_tkip_seq)(struct ieee80211_hw *hw, u8 hw_key_idx,
+			     u32 *iv32, u16 *iv16);
+	int (*set_frag_threshold)(struct ieee80211_hw *hw, u32 value);
+	int (*set_rts_threshold)(struct ieee80211_hw *hw, u32 value);
+	int (*sta_add)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
+		       struct ieee80211_sta *sta);
+	int (*sta_remove)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
+			  struct ieee80211_sta *sta);
+	void (*sta_notify)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
+			enum sta_notify_cmd, struct ieee80211_sta *sta);
+	int (*sta_state)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
+			 struct ieee80211_sta *sta,
+			 enum ieee80211_sta_state old_state,
+			 enum ieee80211_sta_state new_state);
+	int (*conf_tx)(struct ieee80211_hw *hw,
+		       struct ieee80211_vif *vif, u16 queue,
+		       const struct ieee80211_tx_queue_params *params);
+	u64 (*get_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
+	void (*set_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
+			u64 tsf);
+	void (*reset_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
+	int (*tx_last_beacon)(struct ieee80211_hw *hw);
+	int (*ampdu_action)(struct ieee80211_hw *hw,
+			    struct ieee80211_vif *vif,
+			    enum ieee80211_ampdu_mlme_action action,
+			    struct ieee80211_sta *sta, u16 tid, u16 *ssn,
+			    u8 buf_size);
+	int (*get_survey)(struct ieee80211_hw *hw, int idx,
+		struct survey_info *survey);
+	void (*rfkill_poll)(struct ieee80211_hw *hw);
+	void (*set_coverage_class)(struct ieee80211_hw *hw, u8 coverage_class);
+#ifdef CONFIG_NL80211_TESTMODE
+	int (*testmode_cmd)(struct ieee80211_hw *hw, void *data, int len);
+	int (*testmode_dump)(struct ieee80211_hw *hw, struct sk_buff *skb,
+			     struct netlink_callback *cb,
+			     void *data, int len);
+#endif
+	void (*flush)(struct ieee80211_hw *hw, bool drop);
+	void (*channel_switch)(struct ieee80211_hw *hw,
+			       struct ieee80211_channel_switch *ch_switch);
+	int (*napi_poll)(struct ieee80211_hw *hw, int budget);
+	int (*set_antenna)(struct ieee80211_hw *hw, u32 tx_ant, u32 rx_ant);
+	int (*get_antenna)(struct ieee80211_hw *hw, u32 *tx_ant, u32 *rx_ant);
+
+	int (*remain_on_channel)(struct ieee80211_hw *hw,
+				 struct ieee80211_channel *chan,
+				 enum nl80211_channel_type channel_type,
+				 int duration);
+	int (*cancel_remain_on_channel)(struct ieee80211_hw *hw);
+	int (*set_ringparam)(struct ieee80211_hw *hw, u32 tx, u32 rx);
+	void (*get_ringparam)(struct ieee80211_hw *hw,
+			      u32 *tx, u32 *tx_max, u32 *rx, u32 *rx_max);
+	bool (*tx_frames_pending)(struct ieee80211_hw *hw);
+	int (*set_bitrate_mask)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
+				const struct cfg80211_bitrate_mask *mask);
+	void (*rssi_callback)(struct ieee80211_hw *hw,
+			      enum ieee80211_rssi_event rssi_event);
+
+	void (*allow_buffered_frames)(struct ieee80211_hw *hw,
+				      struct ieee80211_sta *sta,
+				      u16 tids, int num_frames,
+				      enum ieee80211_frame_release_type reason,
+				      bool more_data);
+	void (*release_buffered_frames)(struct ieee80211_hw *hw,
+					struct ieee80211_sta *sta,
+					u16 tids, int num_frames,
+					enum ieee80211_frame_release_type reason,
+					bool more_data);
+};
+
+/**
+ * ieee80211_alloc_hw -  Allocate a new hardware device
+ *
+ * This must be called once for each hardware device. The returned pointer
+ * must be used to refer to this device when calling other functions.
+ * mac80211 allocates a private data area for the driver pointed to by
+ * @priv in &struct ieee80211_hw, the size of this area is given as
+ * @priv_data_len.
+ *
+ * @priv_data_len: length of private data
+ * @ops: callbacks for this device
+ */
+struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len,
+					const struct ieee80211_ops *ops);
+
+/**
+ * ieee80211_register_hw - Register hardware device
+ *
+ * You must call this function before any other functions in
+ * mac80211. Note that before a hardware can be registered, you
+ * need to fill the contained wiphy's information.
+ *
+ * @hw: the device to register as returned by ieee80211_alloc_hw()
+ */
+int ieee80211_register_hw(struct ieee80211_hw *hw);
+
+/**
+ * struct ieee80211_tpt_blink - throughput blink description
+ * @throughput: throughput in Kbit/sec
+ * @blink_time: blink time in milliseconds
+ *	(full cycle, ie. one off + one on period)
+ */
+struct ieee80211_tpt_blink {
+	int throughput;
+	int blink_time;
+};
+
+/**
+ * enum ieee80211_tpt_led_trigger_flags - throughput trigger flags
+ * @IEEE80211_TPT_LEDTRIG_FL_RADIO: enable blinking with radio
+ * @IEEE80211_TPT_LEDTRIG_FL_WORK: enable blinking when working
+ * @IEEE80211_TPT_LEDTRIG_FL_CONNECTED: enable blinking when at least one
+ *	interface is connected in some way, including being an AP
+ */
+enum ieee80211_tpt_led_trigger_flags {
+	IEEE80211_TPT_LEDTRIG_FL_RADIO		= BIT(0),
+	IEEE80211_TPT_LEDTRIG_FL_WORK		= BIT(1),
+	IEEE80211_TPT_LEDTRIG_FL_CONNECTED	= BIT(2),
+};
+
+#ifdef CONFIG_MAC80211_LEDS
+extern char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw);
+extern char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw);
+extern char *__ieee80211_get_assoc_led_name(struct ieee80211_hw *hw);
+extern char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw);
+extern char *__ieee80211_create_tpt_led_trigger(
+				struct ieee80211_hw *hw, unsigned int flags,
+				const struct ieee80211_tpt_blink *blink_table,
+				unsigned int blink_table_len);
+#endif
+/**
+ * ieee80211_get_tx_led_name - get name of TX LED
+ *
+ * mac80211 creates a transmit LED trigger for each wireless hardware
+ * that can be used to drive LEDs if your driver registers a LED device.
+ * This function returns the name (or %NULL if not configured for LEDs)
+ * of the trigger so you can automatically link the LED device.
+ *
+ * @hw: the hardware to get the LED trigger name for
+ */
+static inline char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw)
+{
+#ifdef CONFIG_MAC80211_LEDS
+	return __ieee80211_get_tx_led_name(hw);
+#else
+	return NULL;
+#endif
+}
+
+/**
+ * ieee80211_get_rx_led_name - get name of RX LED
+ *
+ * mac80211 creates a receive LED trigger for each wireless hardware
+ * that can be used to drive LEDs if your driver registers a LED device.
+ * This function returns the name (or %NULL if not configured for LEDs)
+ * of the trigger so you can automatically link the LED device.
+ *
+ * @hw: the hardware to get the LED trigger name for
+ */
+static inline char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw)
+{
+#ifdef CONFIG_MAC80211_LEDS
+	return __ieee80211_get_rx_led_name(hw);
+#else
+	return NULL;
+#endif
+}
+
+/**
+ * ieee80211_get_assoc_led_name - get name of association LED
+ *
+ * mac80211 creates a association LED trigger for each wireless hardware
+ * that can be used to drive LEDs if your driver registers a LED device.
+ * This function returns the name (or %NULL if not configured for LEDs)
+ * of the trigger so you can automatically link the LED device.
+ *
+ * @hw: the hardware to get the LED trigger name for
+ */
+static inline char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw)
+{
+#ifdef CONFIG_MAC80211_LEDS
+	return __ieee80211_get_assoc_led_name(hw);
+#else
+	return NULL;
+#endif
+}
+
+/**
+ * ieee80211_get_radio_led_name - get name of radio LED
+ *
+ * mac80211 creates a radio change LED trigger for each wireless hardware
+ * that can be used to drive LEDs if your driver registers a LED device.
+ * This function returns the name (or %NULL if not configured for LEDs)
+ * of the trigger so you can automatically link the LED device.
+ *
+ * @hw: the hardware to get the LED trigger name for
+ */
+static inline char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw)
+{
+#ifdef CONFIG_MAC80211_LEDS
+	return __ieee80211_get_radio_led_name(hw);
+#else
+	return NULL;
+#endif
+}
+
+/**
+ * ieee80211_create_tpt_led_trigger - create throughput LED trigger
+ * @hw: the hardware to create the trigger for
+ * @flags: trigger flags, see &enum ieee80211_tpt_led_trigger_flags
+ * @blink_table: the blink table -- needs to be ordered by throughput
+ * @blink_table_len: size of the blink table
+ *
+ * This function returns %NULL (in case of error, or if no LED
+ * triggers are configured) or the name of the new trigger.
+ * This function must be called before ieee80211_register_hw().
+ */
+static inline char *
+ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw, unsigned int flags,
+				 const struct ieee80211_tpt_blink *blink_table,
+				 unsigned int blink_table_len)
+{
+#ifdef CONFIG_MAC80211_LEDS
+	return __ieee80211_create_tpt_led_trigger(hw, flags, blink_table,
+						  blink_table_len);
+#else
+	return NULL;
+#endif
+}
+
+/**
+ * ieee80211_unregister_hw - Unregister a hardware device
+ *
+ * This function instructs mac80211 to free allocated resources
+ * and unregister netdevices from the networking subsystem.
+ *
+ * @hw: the hardware to unregister
+ */
+void ieee80211_unregister_hw(struct ieee80211_hw *hw);
+
+/**
+ * ieee80211_free_hw - free hardware descriptor
+ *
+ * This function frees everything that was allocated, including the
+ * private data for the driver. You must call ieee80211_unregister_hw()
+ * before calling this function.
+ *
+ * @hw: the hardware to free
+ */
+void ieee80211_free_hw(struct ieee80211_hw *hw);
+
+/**
+ * ieee80211_restart_hw - restart hardware completely
+ *
+ * Call this function when the hardware was restarted for some reason
+ * (hardware error, ...) and the driver is unable to restore its state
+ * by itself. mac80211 assumes that at this point the driver/hardware
+ * is completely uninitialised and stopped, it starts the process by
+ * calling the ->start() operation. The driver will need to reset all
+ * internal state that it has prior to calling this function.
+ *
+ * @hw: the hardware to restart
+ */
+void ieee80211_restart_hw(struct ieee80211_hw *hw);
+
+/** ieee80211_napi_schedule - schedule NAPI poll
+ *
+ * Use this function to schedule NAPI polling on a device.
+ *
+ * @hw: the hardware to start polling
+ */
+void ieee80211_napi_schedule(struct ieee80211_hw *hw);
+
+/** ieee80211_napi_complete - complete NAPI polling
+ *
+ * Use this function to finish NAPI polling on a device.
+ *
+ * @hw: the hardware to stop polling
+ */
+void ieee80211_napi_complete(struct ieee80211_hw *hw);
+
+/**
+ * ieee80211_rx - receive frame
+ *
+ * Use this function to hand received frames to mac80211. The receive
+ * buffer in @skb must start with an IEEE 802.11 header. In case of a
+ * paged @skb is used, the driver is recommended to put the ieee80211
+ * header of the frame on the linear part of the @skb to avoid memory
+ * allocation and/or memcpy by the stack.
+ *
+ * This function may not be called in IRQ context. Calls to this function
+ * for a single hardware must be synchronized against each other. Calls to
+ * this function, ieee80211_rx_ni() and ieee80211_rx_irqsafe() may not be
+ * mixed for a single hardware.
+ *
+ * In process context use instead ieee80211_rx_ni().
+ *
+ * @hw: the hardware this frame came in on
+ * @skb: the buffer to receive, owned by mac80211 after this call
+ */
+void ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb);
+
+/**
+ * ieee80211_rx_irqsafe - receive frame
+ *
+ * Like ieee80211_rx() but can be called in IRQ context
+ * (internally defers to a tasklet.)
+ *
+ * Calls to this function, ieee80211_rx() or ieee80211_rx_ni() may not
+ * be mixed for a single hardware.
+ *
+ * @hw: the hardware this frame came in on
+ * @skb: the buffer to receive, owned by mac80211 after this call
+ */
+void ieee80211_rx_irqsafe(struct ieee80211_hw *hw, struct sk_buff *skb);
+
+/**
+ * ieee80211_rx_ni - receive frame (in process context)
+ *
+ * Like ieee80211_rx() but can be called in process context
+ * (internally disables bottom halves).
+ *
+ * Calls to this function, ieee80211_rx() and ieee80211_rx_irqsafe() may
+ * not be mixed for a single hardware.
+ *
+ * @hw: the hardware this frame came in on
+ * @skb: the buffer to receive, owned by mac80211 after this call
+ */
+static inline void ieee80211_rx_ni(struct ieee80211_hw *hw,
+				   struct sk_buff *skb)
+{
+	local_bh_disable();
+	ieee80211_rx(hw, skb);
+	local_bh_enable();
+}
+
+/**
+ * ieee80211_sta_ps_transition - PS transition for connected sta
+ *
+ * When operating in AP mode with the %IEEE80211_HW_AP_LINK_PS
+ * flag set, use this function to inform mac80211 about a connected station
+ * entering/leaving PS mode.
+ *
+ * This function may not be called in IRQ context or with softirqs enabled.
+ *
+ * Calls to this function for a single hardware must be synchronized against
+ * each other.
+ *
+ * The function returns -EINVAL when the requested PS mode is already set.
+ *
+ * @sta: currently connected sta
+ * @start: start or stop PS
+ */
+int ieee80211_sta_ps_transition(struct ieee80211_sta *sta, bool start);
+
+/**
+ * ieee80211_sta_ps_transition_ni - PS transition for connected sta
+ *                                  (in process context)
+ *
+ * Like ieee80211_sta_ps_transition() but can be called in process context
+ * (internally disables bottom halves). Concurrent call restriction still
+ * applies.
+ *
+ * @sta: currently connected sta
+ * @start: start or stop PS
+ */
+static inline int ieee80211_sta_ps_transition_ni(struct ieee80211_sta *sta,
+						  bool start)
+{
+	int ret;
+
+	local_bh_disable();
+	ret = ieee80211_sta_ps_transition(sta, start);
+	local_bh_enable();
+
+	return ret;
+}
+
+/*
+ * The TX headroom reserved by mac80211 for its own tx_status functions.
+ * This is enough for the radiotap header.
+ */
+#define IEEE80211_TX_STATUS_HEADROOM	14
+
+/**
+ * ieee80211_sta_set_buffered - inform mac80211 about driver-buffered frames
+ * @sta: &struct ieee80211_sta pointer for the sleeping station
+ * @tid: the TID that has buffered frames
+ * @buffered: indicates whether or not frames are buffered for this TID
+ *
+ * If a driver buffers frames for a powersave station instead of passing
+ * them back to mac80211 for retransmission, the station may still need
+ * to be told that there are buffered frames via the TIM bit.
+ *
+ * This function informs mac80211 whether or not there are frames that are
+ * buffered in the driver for a given TID; mac80211 can then use this data
+ * to set the TIM bit (NOTE: This may call back into the driver's set_tim
+ * call! Beware of the locking!)
+ *
+ * If all frames are released to the station (due to PS-poll or uAPSD)
+ * then the driver needs to inform mac80211 that there no longer are
+ * frames buffered. However, when the station wakes up mac80211 assumes
+ * that all buffered frames will be transmitted and clears this data,
+ * drivers need to make sure they inform mac80211 about all buffered
+ * frames on the sleep transition (sta_notify() with %STA_NOTIFY_SLEEP).
+ *
+ * Note that technically mac80211 only needs to know this per AC, not per
+ * TID, but since driver buffering will inevitably happen per TID (since
+ * it is related to aggregation) it is easier to make mac80211 map the
+ * TID to the AC as required instead of keeping track in all drivers that
+ * use this API.
+ */
+void ieee80211_sta_set_buffered(struct ieee80211_sta *sta,
+				u8 tid, bool buffered);
+
+/**
+ * ieee80211_tx_status - transmit status callback
+ *
+ * Call this function for all transmitted frames after they have been
+ * transmitted. It is permissible to not call this function for
+ * multicast frames but this can affect statistics.
+ *
+ * This function may not be called in IRQ context. Calls to this function
+ * for a single hardware must be synchronized against each other. Calls
+ * to this function, ieee80211_tx_status_ni() and ieee80211_tx_status_irqsafe()
+ * may not be mixed for a single hardware.
+ *
+ * @hw: the hardware the frame was transmitted by
+ * @skb: the frame that was transmitted, owned by mac80211 after this call
+ */
+void ieee80211_tx_status(struct ieee80211_hw *hw,
+			 struct sk_buff *skb);
+
+/**
+ * ieee80211_tx_status_ni - transmit status callback (in process context)
+ *
+ * Like ieee80211_tx_status() but can be called in process context.
+ *
+ * Calls to this function, ieee80211_tx_status() and
+ * ieee80211_tx_status_irqsafe() may not be mixed
+ * for a single hardware.
+ *
+ * @hw: the hardware the frame was transmitted by
+ * @skb: the frame that was transmitted, owned by mac80211 after this call
+ */
+static inline void ieee80211_tx_status_ni(struct ieee80211_hw *hw,
+					  struct sk_buff *skb)
+{
+	local_bh_disable();
+	ieee80211_tx_status(hw, skb);
+	local_bh_enable();
+}
+
+/**
+ * ieee80211_tx_status_irqsafe - IRQ-safe transmit status callback
+ *
+ * Like ieee80211_tx_status() but can be called in IRQ context
+ * (internally defers to a tasklet.)
+ *
+ * Calls to this function, ieee80211_tx_status() and
+ * ieee80211_tx_status_ni() may not be mixed for a single hardware.
+ *
+ * @hw: the hardware the frame was transmitted by
+ * @skb: the frame that was transmitted, owned by mac80211 after this call
+ */
+void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw,
+				 struct sk_buff *skb);
+
+/**
+ * ieee80211_report_low_ack - report non-responding station
+ *
+ * When operating in AP-mode, call this function to report a non-responding
+ * connected STA.
+ *
+ * @sta: the non-responding connected sta
+ * @num_packets: number of packets sent to @sta without a response
+ */
+void ieee80211_report_low_ack(struct ieee80211_sta *sta, u32 num_packets);
+
+/**
+ * ieee80211_beacon_get_tim - beacon generation function
+ * @hw: pointer obtained from ieee80211_alloc_hw().
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ * @tim_offset: pointer to variable that will receive the TIM IE offset.
+ *	Set to 0 if invalid (in non-AP modes).
+ * @tim_length: pointer to variable that will receive the TIM IE length,
+ *	(including the ID and length bytes!).
+ *	Set to 0 if invalid (in non-AP modes).
+ *
+ * If the driver implements beaconing modes, it must use this function to
+ * obtain the beacon frame/template.
+ *
+ * If the beacon frames are generated by the host system (i.e., not in
+ * hardware/firmware), the driver uses this function to get each beacon
+ * frame from mac80211 -- it is responsible for calling this function
+ * before the beacon is needed (e.g. based on hardware interrupt).
+ *
+ * If the beacon frames are generated by the device, then the driver
+ * must use the returned beacon as the template and change the TIM IE
+ * according to the current DTIM parameters/TIM bitmap.
+ *
+ * The driver is responsible for freeing the returned skb.
+ */
+struct sk_buff *ieee80211_beacon_get_tim(struct ieee80211_hw *hw,
+					 struct ieee80211_vif *vif,
+					 u16 *tim_offset, u16 *tim_length);
+
+/**
+ * ieee80211_beacon_get - beacon generation function
+ * @hw: pointer obtained from ieee80211_alloc_hw().
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ *
+ * See ieee80211_beacon_get_tim().
+ */
+static inline struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw,
+						   struct ieee80211_vif *vif)
+{
+	return ieee80211_beacon_get_tim(hw, vif, NULL, NULL);
+}
+
+/**
+ * ieee80211_proberesp_get - retrieve a Probe Response template
+ * @hw: pointer obtained from ieee80211_alloc_hw().
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ *
+ * Creates a Probe Response template which can, for example, be uploaded to
+ * hardware. The destination address should be set by the caller.
+ *
+ * Can only be called in AP mode.
+ */
+struct sk_buff *ieee80211_proberesp_get(struct ieee80211_hw *hw,
+					struct ieee80211_vif *vif);
+
+/**
+ * ieee80211_pspoll_get - retrieve a PS Poll template
+ * @hw: pointer obtained from ieee80211_alloc_hw().
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ *
+ * Creates a PS Poll a template which can, for example, uploaded to
+ * hardware. The template must be updated after association so that correct
+ * AID, BSSID and MAC address is used.
+ *
+ * Note: Caller (or hardware) is responsible for setting the
+ * &IEEE80211_FCTL_PM bit.
+ */
+struct sk_buff *ieee80211_pspoll_get(struct ieee80211_hw *hw,
+				     struct ieee80211_vif *vif);
+
+/**
+ * ieee80211_nullfunc_get - retrieve a nullfunc template
+ * @hw: pointer obtained from ieee80211_alloc_hw().
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ *
+ * Creates a Nullfunc template which can, for example, uploaded to
+ * hardware. The template must be updated after association so that correct
+ * BSSID and address is used.
+ *
+ * Note: Caller (or hardware) is responsible for setting the
+ * &IEEE80211_FCTL_PM bit as well as Duration and Sequence Control fields.
+ */
+struct sk_buff *ieee80211_nullfunc_get(struct ieee80211_hw *hw,
+				       struct ieee80211_vif *vif);
+
+/**
+ * ieee80211_probereq_get - retrieve a Probe Request template
+ * @hw: pointer obtained from ieee80211_alloc_hw().
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ * @ssid: SSID buffer
+ * @ssid_len: length of SSID
+ * @ie: buffer containing all IEs except SSID for the template
+ * @ie_len: length of the IE buffer
+ *
+ * Creates a Probe Request template which can, for example, be uploaded to
+ * hardware.
+ */
+struct sk_buff *ieee80211_probereq_get(struct ieee80211_hw *hw,
+				       struct ieee80211_vif *vif,
+				       const u8 *ssid, size_t ssid_len,
+				       const u8 *ie, size_t ie_len);
+
+/**
+ * ieee80211_rts_get - RTS frame generation function
+ * @hw: pointer obtained from ieee80211_alloc_hw().
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ * @frame: pointer to the frame that is going to be protected by the RTS.
+ * @frame_len: the frame length (in octets).
+ * @frame_txctl: &struct ieee80211_tx_info of the frame.
+ * @rts: The buffer where to store the RTS frame.
+ *
+ * If the RTS frames are generated by the host system (i.e., not in
+ * hardware/firmware), the low-level driver uses this function to receive
+ * the next RTS frame from the 802.11 code. The low-level is responsible
+ * for calling this function before and RTS frame is needed.
+ */
+void ieee80211_rts_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
+		       const void *frame, size_t frame_len,
+		       const struct ieee80211_tx_info *frame_txctl,
+		       struct ieee80211_rts *rts);
+
+/**
+ * ieee80211_rts_duration - Get the duration field for an RTS frame
+ * @hw: pointer obtained from ieee80211_alloc_hw().
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ * @frame_len: the length of the frame that is going to be protected by the RTS.
+ * @frame_txctl: &struct ieee80211_tx_info of the frame.
+ *
+ * If the RTS is generated in firmware, but the host system must provide
+ * the duration field, the low-level driver uses this function to receive
+ * the duration field value in little-endian byteorder.
+ */
+__le16 ieee80211_rts_duration(struct ieee80211_hw *hw,
+			      struct ieee80211_vif *vif, size_t frame_len,
+			      const struct ieee80211_tx_info *frame_txctl);
+
+/**
+ * ieee80211_ctstoself_get - CTS-to-self frame generation function
+ * @hw: pointer obtained from ieee80211_alloc_hw().
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ * @frame: pointer to the frame that is going to be protected by the CTS-to-self.
+ * @frame_len: the frame length (in octets).
+ * @frame_txctl: &struct ieee80211_tx_info of the frame.
+ * @cts: The buffer where to store the CTS-to-self frame.
+ *
+ * If the CTS-to-self frames are generated by the host system (i.e., not in
+ * hardware/firmware), the low-level driver uses this function to receive
+ * the next CTS-to-self frame from the 802.11 code. The low-level is responsible
+ * for calling this function before and CTS-to-self frame is needed.
+ */
+void ieee80211_ctstoself_get(struct ieee80211_hw *hw,
+			     struct ieee80211_vif *vif,
+			     const void *frame, size_t frame_len,
+			     const struct ieee80211_tx_info *frame_txctl,
+			     struct ieee80211_cts *cts);
+
+/**
+ * ieee80211_ctstoself_duration - Get the duration field for a CTS-to-self frame
+ * @hw: pointer obtained from ieee80211_alloc_hw().
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ * @frame_len: the length of the frame that is going to be protected by the CTS-to-self.
+ * @frame_txctl: &struct ieee80211_tx_info of the frame.
+ *
+ * If the CTS-to-self is generated in firmware, but the host system must provide
+ * the duration field, the low-level driver uses this function to receive
+ * the duration field value in little-endian byteorder.
+ */
+__le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw,
+				    struct ieee80211_vif *vif,
+				    size_t frame_len,
+				    const struct ieee80211_tx_info *frame_txctl);
+
+/**
+ * ieee80211_generic_frame_duration - Calculate the duration field for a frame
+ * @hw: pointer obtained from ieee80211_alloc_hw().
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ * @frame_len: the length of the frame.
+ * @rate: the rate at which the frame is going to be transmitted.
+ *
+ * Calculate the duration field of some generic frame, given its
+ * length and transmission rate (in 100kbps).
+ */
+__le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw,
+					struct ieee80211_vif *vif,
+					size_t frame_len,
+					struct ieee80211_rate *rate);
+
+/**
+ * ieee80211_get_buffered_bc - accessing buffered broadcast and multicast frames
+ * @hw: pointer as obtained from ieee80211_alloc_hw().
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ *
+ * Function for accessing buffered broadcast and multicast frames. If
+ * hardware/firmware does not implement buffering of broadcast/multicast
+ * frames when power saving is used, 802.11 code buffers them in the host
+ * memory. The low-level driver uses this function to fetch next buffered
+ * frame. In most cases, this is used when generating beacon frame. This
+ * function returns a pointer to the next buffered skb or NULL if no more
+ * buffered frames are available.
+ *
+ * Note: buffered frames are returned only after DTIM beacon frame was
+ * generated with ieee80211_beacon_get() and the low-level driver must thus
+ * call ieee80211_beacon_get() first. ieee80211_get_buffered_bc() returns
+ * NULL if the previous generated beacon was not DTIM, so the low-level driver
+ * does not need to check for DTIM beacons separately and should be able to
+ * use common code for all beacons.
+ */
+struct sk_buff *
+ieee80211_get_buffered_bc(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
+
+/**
+ * ieee80211_get_tkip_p1k_iv - get a TKIP phase 1 key for IV32
+ *
+ * This function returns the TKIP phase 1 key for the given IV32.
+ *
+ * @keyconf: the parameter passed with the set key
+ * @iv32: IV32 to get the P1K for
+ * @p1k: a buffer to which the key will be written, as 5 u16 values
+ */
+void ieee80211_get_tkip_p1k_iv(struct ieee80211_key_conf *keyconf,
+			       u32 iv32, u16 *p1k);
+
+/**
+ * ieee80211_get_tkip_p1k - get a TKIP phase 1 key
+ *
+ * This function returns the TKIP phase 1 key for the IV32 taken
+ * from the given packet.
+ *
+ * @keyconf: the parameter passed with the set key
+ * @skb: the packet to take the IV32 value from that will be encrypted
+ *	with this P1K
+ * @p1k: a buffer to which the key will be written, as 5 u16 values
+ */
+static inline void ieee80211_get_tkip_p1k(struct ieee80211_key_conf *keyconf,
+					  struct sk_buff *skb, u16 *p1k)
+{
+	struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
+	const u8 *data = (u8 *)hdr + ieee80211_hdrlen(hdr->frame_control);
+	u32 iv32 = get_unaligned_le32(&data[4]);
+
+	ieee80211_get_tkip_p1k_iv(keyconf, iv32, p1k);
+}
+
+/**
+ * ieee80211_get_tkip_rx_p1k - get a TKIP phase 1 key for RX
+ *
+ * This function returns the TKIP phase 1 key for the given IV32
+ * and transmitter address.
+ *
+ * @keyconf: the parameter passed with the set key
+ * @ta: TA that will be used with the key
+ * @iv32: IV32 to get the P1K for
+ * @p1k: a buffer to which the key will be written, as 5 u16 values
+ */
+void ieee80211_get_tkip_rx_p1k(struct ieee80211_key_conf *keyconf,
+			       const u8 *ta, u32 iv32, u16 *p1k);
+
+/**
+ * ieee80211_get_tkip_p2k - get a TKIP phase 2 key
+ *
+ * This function computes the TKIP RC4 key for the IV values
+ * in the packet.
+ *
+ * @keyconf: the parameter passed with the set key
+ * @skb: the packet to take the IV32/IV16 values from that will be
+ *	encrypted with this key
+ * @p2k: a buffer to which the key will be written, 16 bytes
+ */
+void ieee80211_get_tkip_p2k(struct ieee80211_key_conf *keyconf,
+			    struct sk_buff *skb, u8 *p2k);
+
+/**
+ * struct ieee80211_key_seq - key sequence counter
+ *
+ * @tkip: TKIP data, containing IV32 and IV16 in host byte order
+ * @ccmp: PN data, most significant byte first (big endian,
+ *	reverse order than in packet)
+ * @aes_cmac: PN data, most significant byte first (big endian,
+ *	reverse order than in packet)
+ */
+struct ieee80211_key_seq {
+	union {
+		struct {
+			u32 iv32;
+			u16 iv16;
+		} tkip;
+		struct {
+			u8 pn[6];
+		} ccmp;
+		struct {
+			u8 pn[6];
+		} aes_cmac;
+	};
+};
+
+/**
+ * ieee80211_get_key_tx_seq - get key TX sequence counter
+ *
+ * @keyconf: the parameter passed with the set key
+ * @seq: buffer to receive the sequence data
+ *
+ * This function allows a driver to retrieve the current TX IV/PN
+ * for the given key. It must not be called if IV generation is
+ * offloaded to the device.
+ *
+ * Note that this function may only be called when no TX processing
+ * can be done concurrently, for example when queues are stopped
+ * and the stop has been synchronized.
+ */
+void ieee80211_get_key_tx_seq(struct ieee80211_key_conf *keyconf,
+			      struct ieee80211_key_seq *seq);
+
+/**
+ * ieee80211_get_key_rx_seq - get key RX sequence counter
+ *
+ * @keyconf: the parameter passed with the set key
+ * @tid: The TID, or -1 for the management frame value (CCMP only);
+ *	the value on TID 0 is also used for non-QoS frames. For
+ *	CMAC, only TID 0 is valid.
+ * @seq: buffer to receive the sequence data
+ *
+ * This function allows a driver to retrieve the current RX IV/PNs
+ * for the given key. It must not be called if IV checking is done
+ * by the device and not by mac80211.
+ *
+ * Note that this function may only be called when no RX processing
+ * can be done concurrently.
+ */
+void ieee80211_get_key_rx_seq(struct ieee80211_key_conf *keyconf,
+			      int tid, struct ieee80211_key_seq *seq);
+
+/**
+ * ieee80211_gtk_rekey_notify - notify userspace supplicant of rekeying
+ * @vif: virtual interface the rekeying was done on
+ * @bssid: The BSSID of the AP, for checking association
+ * @replay_ctr: the new replay counter after GTK rekeying
+ * @gfp: allocation flags
+ */
+void ieee80211_gtk_rekey_notify(struct ieee80211_vif *vif, const u8 *bssid,
+				const u8 *replay_ctr, gfp_t gfp);
+
+/**
+ * ieee80211_wake_queue - wake specific queue
+ * @hw: pointer as obtained from ieee80211_alloc_hw().
+ * @queue: queue number (counted from zero).
+ *
+ * Drivers should use this function instead of netif_wake_queue.
+ */
+void ieee80211_wake_queue(struct ieee80211_hw *hw, int queue);
+
+/**
+ * ieee80211_stop_queue - stop specific queue
+ * @hw: pointer as obtained from ieee80211_alloc_hw().
+ * @queue: queue number (counted from zero).
+ *
+ * Drivers should use this function instead of netif_stop_queue.
+ */
+void ieee80211_stop_queue(struct ieee80211_hw *hw, int queue);
+
+/**
+ * ieee80211_queue_stopped - test status of the queue
+ * @hw: pointer as obtained from ieee80211_alloc_hw().
+ * @queue: queue number (counted from zero).
+ *
+ * Drivers should use this function instead of netif_stop_queue.
+ */
+
+int ieee80211_queue_stopped(struct ieee80211_hw *hw, int queue);
+
+/**
+ * ieee80211_stop_queues - stop all queues
+ * @hw: pointer as obtained from ieee80211_alloc_hw().
+ *
+ * Drivers should use this function instead of netif_stop_queue.
+ */
+void ieee80211_stop_queues(struct ieee80211_hw *hw);
+
+/**
+ * ieee80211_wake_queues - wake all queues
+ * @hw: pointer as obtained from ieee80211_alloc_hw().
+ *
+ * Drivers should use this function instead of netif_wake_queue.
+ */
+void ieee80211_wake_queues(struct ieee80211_hw *hw);
+
+/**
+ * ieee80211_scan_completed - completed hardware scan
+ *
+ * When hardware scan offload is used (i.e. the hw_scan() callback is
+ * assigned) this function needs to be called by the driver to notify
+ * mac80211 that the scan finished. This function can be called from
+ * any context, including hardirq context.
+ *
+ * @hw: the hardware that finished the scan
+ * @aborted: set to true if scan was aborted
+ */
+void ieee80211_scan_completed(struct ieee80211_hw *hw, bool aborted);
+
+/**
+ * ieee80211_sched_scan_results - got results from scheduled scan
+ *
+ * When a scheduled scan is running, this function needs to be called by the
+ * driver whenever there are new scan results available.
+ *
+ * @hw: the hardware that is performing scheduled scans
+ */
+void ieee80211_sched_scan_results(struct ieee80211_hw *hw);
+
+/**
+ * ieee80211_sched_scan_stopped - inform that the scheduled scan has stopped
+ *
+ * When a scheduled scan is running, this function can be called by
+ * the driver if it needs to stop the scan to perform another task.
+ * Usual scenarios are drivers that cannot continue the scheduled scan
+ * while associating, for instance.
+ *
+ * @hw: the hardware that is performing scheduled scans
+ */
+void ieee80211_sched_scan_stopped(struct ieee80211_hw *hw);
+
+/**
+ * ieee80211_iterate_active_interfaces - iterate active interfaces
+ *
+ * This function iterates over the interfaces associated with a given
+ * hardware that are currently active and calls the callback for them.
+ * This function allows the iterator function to sleep, when the iterator
+ * function is atomic @ieee80211_iterate_active_interfaces_atomic can
+ * be used.
+ * Does not iterate over a new interface during add_interface()
+ *
+ * @hw: the hardware struct of which the interfaces should be iterated over
+ * @iterator: the iterator function to call
+ * @data: first argument of the iterator function
+ */
+void ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw,
+					 void (*iterator)(void *data, u8 *mac,
+						struct ieee80211_vif *vif),
+					 void *data);
+
+/**
+ * ieee80211_iterate_active_interfaces_atomic - iterate active interfaces
+ *
+ * This function iterates over the interfaces associated with a given
+ * hardware that are currently active and calls the callback for them.
+ * This function requires the iterator callback function to be atomic,
+ * if that is not desired, use @ieee80211_iterate_active_interfaces instead.
+ * Does not iterate over a new interface during add_interface()
+ *
+ * @hw: the hardware struct of which the interfaces should be iterated over
+ * @iterator: the iterator function to call, cannot sleep
+ * @data: first argument of the iterator function
+ */
+void ieee80211_iterate_active_interfaces_atomic(struct ieee80211_hw *hw,
+						void (*iterator)(void *data,
+						    u8 *mac,
+						    struct ieee80211_vif *vif),
+						void *data);
+
+/**
+ * ieee80211_queue_work - add work onto the mac80211 workqueue
+ *
+ * Drivers and mac80211 use this to add work onto the mac80211 workqueue.
+ * This helper ensures drivers are not queueing work when they should not be.
+ *
+ * @hw: the hardware struct for the interface we are adding work for
+ * @work: the work we want to add onto the mac80211 workqueue
+ */
+void ieee80211_queue_work(struct ieee80211_hw *hw, struct work_struct *work);
+
+/**
+ * ieee80211_queue_delayed_work - add work onto the mac80211 workqueue
+ *
+ * Drivers and mac80211 use this to queue delayed work onto the mac80211
+ * workqueue.
+ *
+ * @hw: the hardware struct for the interface we are adding work for
+ * @dwork: delayable work to queue onto the mac80211 workqueue
+ * @delay: number of jiffies to wait before queueing
+ */
+void ieee80211_queue_delayed_work(struct ieee80211_hw *hw,
+				  struct delayed_work *dwork,
+				  unsigned long delay);
+
+/**
+ * ieee80211_start_tx_ba_session - Start a tx Block Ack session.
+ * @sta: the station for which to start a BA session
+ * @tid: the TID to BA on.
+ * @timeout: session timeout value (in TUs)
+ *
+ * Return: success if addBA request was sent, failure otherwise
+ *
+ * Although mac80211/low level driver/user space application can estimate
+ * the need to start aggregation on a certain RA/TID, the session level
+ * will be managed by the mac80211.
+ */
+int ieee80211_start_tx_ba_session(struct ieee80211_sta *sta, u16 tid,
+				  u16 timeout);
+
+/**
+ * ieee80211_start_tx_ba_cb_irqsafe - low level driver ready to aggregate.
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback
+ * @ra: receiver address of the BA session recipient.
+ * @tid: the TID to BA on.
+ *
+ * This function must be called by low level driver once it has
+ * finished with preparations for the BA session. It can be called
+ * from any context.
+ */
+void ieee80211_start_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra,
+				      u16 tid);
+
+/**
+ * ieee80211_stop_tx_ba_session - Stop a Block Ack session.
+ * @sta: the station whose BA session to stop
+ * @tid: the TID to stop BA.
+ *
+ * Return: negative error if the TID is invalid, or no aggregation active
+ *
+ * Although mac80211/low level driver/user space application can estimate
+ * the need to stop aggregation on a certain RA/TID, the session level
+ * will be managed by the mac80211.
+ */
+int ieee80211_stop_tx_ba_session(struct ieee80211_sta *sta, u16 tid);
+
+/**
+ * ieee80211_stop_tx_ba_cb_irqsafe - low level driver ready to stop aggregate.
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback
+ * @ra: receiver address of the BA session recipient.
+ * @tid: the desired TID to BA on.
+ *
+ * This function must be called by low level driver once it has
+ * finished with preparations for the BA session tear down. It
+ * can be called from any context.
+ */
+void ieee80211_stop_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra,
+				     u16 tid);
+
+/**
+ * ieee80211_find_sta - find a station
+ *
+ * @vif: virtual interface to look for station on
+ * @addr: station's address
+ *
+ * This function must be called under RCU lock and the
+ * resulting pointer is only valid under RCU lock as well.
+ */
+struct ieee80211_sta *ieee80211_find_sta(struct ieee80211_vif *vif,
+					 const u8 *addr);
+
+/**
+ * ieee80211_find_sta_by_ifaddr - find a station on hardware
+ *
+ * @hw: pointer as obtained from ieee80211_alloc_hw()
+ * @addr: remote station's address
+ * @localaddr: local address (vif->sdata->vif.addr). Use NULL for 'any'.
+ *
+ * This function must be called under RCU lock and the
+ * resulting pointer is only valid under RCU lock as well.
+ *
+ * NOTE: You may pass NULL for localaddr, but then you will just get
+ *      the first STA that matches the remote address 'addr'.
+ *      We can have multiple STA associated with multiple
+ *      logical stations (e.g. consider a station connecting to another
+ *      BSSID on the same AP hardware without disconnecting first).
+ *      In this case, the result of this method with localaddr NULL
+ *      is not reliable.
+ *
+ * DO NOT USE THIS FUNCTION with localaddr NULL if at all possible.
+ */
+struct ieee80211_sta *ieee80211_find_sta_by_ifaddr(struct ieee80211_hw *hw,
+					       const u8 *addr,
+					       const u8 *localaddr);
+
+/**
+ * ieee80211_sta_block_awake - block station from waking up
+ * @hw: the hardware
+ * @pubsta: the station
+ * @block: whether to block or unblock
+ *
+ * Some devices require that all frames that are on the queues
+ * for a specific station that went to sleep are flushed before
+ * a poll response or frames after the station woke up can be
+ * delivered to that it. Note that such frames must be rejected
+ * by the driver as filtered, with the appropriate status flag.
+ *
+ * This function allows implementing this mode in a race-free
+ * manner.
+ *
+ * To do this, a driver must keep track of the number of frames
+ * still enqueued for a specific station. If this number is not
+ * zero when the station goes to sleep, the driver must call
+ * this function to force mac80211 to consider the station to
+ * be asleep regardless of the station's actual state. Once the
+ * number of outstanding frames reaches zero, the driver must
+ * call this function again to unblock the station. That will
+ * cause mac80211 to be able to send ps-poll responses, and if
+ * the station queried in the meantime then frames will also
+ * be sent out as a result of this. Additionally, the driver
+ * will be notified that the station woke up some time after
+ * it is unblocked, regardless of whether the station actually
+ * woke up while blocked or not.
+ */
+void ieee80211_sta_block_awake(struct ieee80211_hw *hw,
+			       struct ieee80211_sta *pubsta, bool block);
+
+/**
+ * ieee80211_sta_eosp - notify mac80211 about end of SP
+ * @pubsta: the station
+ *
+ * When a device transmits frames in a way that it can't tell
+ * mac80211 in the TX status about the EOSP, it must clear the
+ * %IEEE80211_TX_STATUS_EOSP bit and call this function instead.
+ * This applies for PS-Poll as well as uAPSD.
+ *
+ * Note that there is no non-_irqsafe version right now as
+ * it wasn't needed, but just like _tx_status() and _rx()
+ * must not be mixed in irqsafe/non-irqsafe versions, this
+ * function must not be mixed with those either. Use the
+ * all irqsafe, or all non-irqsafe, don't mix! If you need
+ * the non-irqsafe version of this, you need to add it.
+ */
+void ieee80211_sta_eosp_irqsafe(struct ieee80211_sta *pubsta);
+
+/**
+ * ieee80211_iter_keys - iterate keys programmed into the device
+ * @hw: pointer obtained from ieee80211_alloc_hw()
+ * @vif: virtual interface to iterate, may be %NULL for all
+ * @iter: iterator function that will be called for each key
+ * @iter_data: custom data to pass to the iterator function
+ *
+ * This function can be used to iterate all the keys known to
+ * mac80211, even those that weren't previously programmed into
+ * the device. This is intended for use in WoWLAN if the device
+ * needs reprogramming of the keys during suspend. Note that due
+ * to locking reasons, it is also only safe to call this at few
+ * spots since it must hold the RTNL and be able to sleep.
+ *
+ * The order in which the keys are iterated matches the order
+ * in which they were originally installed and handed to the
+ * set_key callback.
+ */
+void ieee80211_iter_keys(struct ieee80211_hw *hw,
+			 struct ieee80211_vif *vif,
+			 void (*iter)(struct ieee80211_hw *hw,
+				      struct ieee80211_vif *vif,
+				      struct ieee80211_sta *sta,
+				      struct ieee80211_key_conf *key,
+				      void *data),
+			 void *iter_data);
+
+/**
+ * ieee80211_ap_probereq_get - retrieve a Probe Request template
+ * @hw: pointer obtained from ieee80211_alloc_hw().
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ *
+ * Creates a Probe Request template which can, for example, be uploaded to
+ * hardware. The template is filled with bssid, ssid and supported rate
+ * information. This function must only be called from within the
+ * .bss_info_changed callback function and only in managed mode. The function
+ * is only useful when the interface is associated, otherwise it will return
+ * NULL.
+ */
+struct sk_buff *ieee80211_ap_probereq_get(struct ieee80211_hw *hw,
+					  struct ieee80211_vif *vif);
+
+/**
+ * ieee80211_beacon_loss - inform hardware does not receive beacons
+ *
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ *
+ * When beacon filtering is enabled with %IEEE80211_VIF_BEACON_FILTER and
+ * %IEEE80211_CONF_PS is set, the driver needs to inform whenever the
+ * hardware is not receiving beacons with this function.
+ */
+void ieee80211_beacon_loss(struct ieee80211_vif *vif);
+
+/**
+ * ieee80211_connection_loss - inform hardware has lost connection to the AP
+ *
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ *
+ * When beacon filtering is enabled with %IEEE80211_VIF_BEACON_FILTER, and
+ * %IEEE80211_CONF_PS and %IEEE80211_HW_CONNECTION_MONITOR are set, the driver
+ * needs to inform if the connection to the AP has been lost.
+ *
+ * This function will cause immediate change to disassociated state,
+ * without connection recovery attempts.
+ */
+void ieee80211_connection_loss(struct ieee80211_vif *vif);
+
+/**
+ * ieee80211_resume_disconnect - disconnect from AP after resume
+ *
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ *
+ * Instructs mac80211 to disconnect from the AP after resume.
+ * Drivers can use this after WoWLAN if they know that the
+ * connection cannot be kept up, for example because keys were
+ * used while the device was asleep but the replay counters or
+ * similar cannot be retrieved from the device during resume.
+ *
+ * Note that due to implementation issues, if the driver uses
+ * the reconfiguration functionality during resume the interface
+ * will still be added as associated first during resume and then
+ * disconnect normally later.
+ *
+ * This function can only be called from the resume callback and
+ * the driver must not be holding any of its own locks while it
+ * calls this function, or at least not any locks it needs in the
+ * key configuration paths (if it supports HW crypto).
+ */
+void ieee80211_resume_disconnect(struct ieee80211_vif *vif);
+
+/**
+ * ieee80211_disable_dyn_ps - force mac80211 to temporarily disable dynamic psm
+ *
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ *
+ * Some hardware require full power save to manage simultaneous BT traffic
+ * on the WLAN frequency. Full PSM is required periodically, whenever there are
+ * burst of BT traffic. The hardware gets information of BT traffic via
+ * hardware co-existence lines, and consequentially requests mac80211 to
+ * (temporarily) enter full psm.
+ * This function will only temporarily disable dynamic PS, not enable PSM if
+ * it was not already enabled.
+ * The driver must make sure to re-enable dynamic PS using
+ * ieee80211_enable_dyn_ps() if the driver has disabled it.
+ *
+ */
+void ieee80211_disable_dyn_ps(struct ieee80211_vif *vif);
+
+/**
+ * ieee80211_enable_dyn_ps - restore dynamic psm after being disabled
+ *
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ *
+ * This function restores dynamic PS after being temporarily disabled via
+ * ieee80211_disable_dyn_ps(). Each ieee80211_disable_dyn_ps() call must
+ * be coupled with an eventual call to this function.
+ *
+ */
+void ieee80211_enable_dyn_ps(struct ieee80211_vif *vif);
+
+/**
+ * ieee80211_cqm_rssi_notify - inform a configured connection quality monitoring
+ *	rssi threshold triggered
+ *
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ * @rssi_event: the RSSI trigger event type
+ * @gfp: context flags
+ *
+ * When the %IEEE80211_VIF_SUPPORTS_CQM_RSSI is set, and a connection quality
+ * monitoring is configured with an rssi threshold, the driver will inform
+ * whenever the rssi level reaches the threshold.
+ */
+void ieee80211_cqm_rssi_notify(struct ieee80211_vif *vif,
+			       enum nl80211_cqm_rssi_threshold_event rssi_event,
+			       gfp_t gfp);
+
+/**
+ * ieee80211_get_operstate - get the operstate of the vif
+ *
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ *
+ * The driver might need to know the operstate of the net_device
+ * (specifically, whether the link is IF_OPER_UP after resume)
+ */
+unsigned char ieee80211_get_operstate(struct ieee80211_vif *vif);
+
+/**
+ * ieee80211_chswitch_done - Complete channel switch process
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ * @success: make the channel switch successful or not
+ *
+ * Complete the channel switch post-process: set the new operational channel
+ * and wake up the suspended queues.
+ */
+void ieee80211_chswitch_done(struct ieee80211_vif *vif, bool success);
+
+/**
+ * ieee80211_request_smps - request SM PS transition
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ * @smps_mode: new SM PS mode
+ *
+ * This allows the driver to request an SM PS transition in managed
+ * mode. This is useful when the driver has more information than
+ * the stack about possible interference, for example by bluetooth.
+ */
+void ieee80211_request_smps(struct ieee80211_vif *vif,
+			    enum ieee80211_smps_mode smps_mode);
+
+/**
+ * ieee80211_key_removed - disable hw acceleration for key
+ * @key_conf: The key hw acceleration should be disabled for
+ *
+ * This allows drivers to indicate that the given key has been
+ * removed from hardware acceleration, due to a new key that
+ * was added. Don't use this if the key can continue to be used
+ * for TX, if the key restriction is on RX only it is permitted
+ * to keep the key for TX only and not call this function.
+ *
+ * Due to locking constraints, it may only be called during
+ * @set_key. This function must be allowed to sleep, and the
+ * key it tries to disable may still be used until it returns.
+ */
+void ieee80211_key_removed(struct ieee80211_key_conf *key_conf);
+
+/**
+ * ieee80211_ready_on_channel - notification of remain-on-channel start
+ * @hw: pointer as obtained from ieee80211_alloc_hw()
+ */
+void ieee80211_ready_on_channel(struct ieee80211_hw *hw);
+
+/**
+ * ieee80211_remain_on_channel_expired - remain_on_channel duration expired
+ * @hw: pointer as obtained from ieee80211_alloc_hw()
+ */
+void ieee80211_remain_on_channel_expired(struct ieee80211_hw *hw);
+
+/**
+ * ieee80211_stop_rx_ba_session - callback to stop existing BA sessions
+ *
+ * in order not to harm the system performance and user experience, the device
+ * may request not to allow any rx ba session and tear down existing rx ba
+ * sessions based on system constraints such as periodic BT activity that needs
+ * to limit wlan activity (eg.sco or a2dp)."
+ * in such cases, the intention is to limit the duration of the rx ppdu and
+ * therefore prevent the peer device to use a-mpdu aggregation.
+ *
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ * @ba_rx_bitmap: Bit map of open rx ba per tid
+ * @addr: & to bssid mac address
+ */
+void ieee80211_stop_rx_ba_session(struct ieee80211_vif *vif, u16 ba_rx_bitmap,
+				  const u8 *addr);
+
+/**
+ * ieee80211_send_bar - send a BlockAckReq frame
+ *
+ * can be used to flush pending frames from the peer's aggregation reorder
+ * buffer.
+ *
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ * @ra: the peer's destination address
+ * @tid: the TID of the aggregation session
+ * @ssn: the new starting sequence number for the receiver
+ */
+void ieee80211_send_bar(struct ieee80211_vif *vif, u8 *ra, u16 tid, u16 ssn);
+
+/* Rate control API */
+
+/**
+ * enum rate_control_changed - flags to indicate which parameter changed
+ *
+ * @IEEE80211_RC_HT_CHANGED: The HT parameters of the operating channel have
+ *	changed, rate control algorithm can update its internal state if needed.
+ * @IEEE80211_RC_SMPS_CHANGED: The SMPS state of the station changed, the rate
+ *	control algorithm needs to adjust accordingly.
+ */
+enum rate_control_changed {
+	IEEE80211_RC_HT_CHANGED		= BIT(0),
+	IEEE80211_RC_SMPS_CHANGED	= BIT(1),
+};
+
+/**
+ * struct ieee80211_tx_rate_control - rate control information for/from RC algo
+ *
+ * @hw: The hardware the algorithm is invoked for.
+ * @sband: The band this frame is being transmitted on.
+ * @bss_conf: the current BSS configuration
+ * @skb: the skb that will be transmitted, the control information in it needs
+ *	to be filled in
+ * @reported_rate: The rate control algorithm can fill this in to indicate
+ *	which rate should be reported to userspace as the current rate and
+ *	used for rate calculations in the mesh network.
+ * @rts: whether RTS will be used for this frame because it is longer than the
+ *	RTS threshold
+ * @short_preamble: whether mac80211 will request short-preamble transmission
+ *	if the selected rate supports it
+ * @max_rate_idx: user-requested maximum (legacy) rate
+ *	(deprecated; this will be removed once drivers get updated to use
+ *	rate_idx_mask)
+ * @rate_idx_mask: user-requested (legacy) rate mask
+ * @rate_idx_mcs_mask: user-requested MCS rate mask
+ * @bss: whether this frame is sent out in AP or IBSS mode
+ */
+struct ieee80211_tx_rate_control {
+	struct ieee80211_hw *hw;
+	struct ieee80211_supported_band *sband;
+	struct ieee80211_bss_conf *bss_conf;
+	struct sk_buff *skb;
+	struct ieee80211_tx_rate reported_rate;
+	bool rts, short_preamble;
+	u8 max_rate_idx;
+	u32 rate_idx_mask;
+	u8 rate_idx_mcs_mask[IEEE80211_HT_MCS_MASK_LEN];
+	bool bss;
+};
+
+struct rate_control_ops {
+	struct module *module;
+	const char *name;
+	void *(*alloc)(struct ieee80211_hw *hw, struct dentry *debugfsdir);
+	void (*free)(void *priv);
+
+	void *(*alloc_sta)(void *priv, struct ieee80211_sta *sta, gfp_t gfp);
+	void (*rate_init)(void *priv, struct ieee80211_supported_band *sband,
+			  struct ieee80211_sta *sta, void *priv_sta);
+	void (*rate_update)(void *priv, struct ieee80211_supported_band *sband,
+			    struct ieee80211_sta *sta,
+			    void *priv_sta, u32 changed,
+			    enum nl80211_channel_type oper_chan_type);
+	void (*free_sta)(void *priv, struct ieee80211_sta *sta,
+			 void *priv_sta);
+
+	void (*tx_status)(void *priv, struct ieee80211_supported_band *sband,
+			  struct ieee80211_sta *sta, void *priv_sta,
+			  struct sk_buff *skb);
+	void (*get_rate)(void *priv, struct ieee80211_sta *sta, void *priv_sta,
+			 struct ieee80211_tx_rate_control *txrc);
+
+	void (*add_sta_debugfs)(void *priv, void *priv_sta,
+				struct dentry *dir);
+	void (*remove_sta_debugfs)(void *priv, void *priv_sta);
+};
+
+static inline int rate_supported(struct ieee80211_sta *sta,
+				 enum ieee80211_band band,
+				 int index)
+{
+	return (sta == NULL || sta->supp_rates[band] & BIT(index));
+}
+
+/**
+ * rate_control_send_low - helper for drivers for management/no-ack frames
+ *
+ * Rate control algorithms that agree to use the lowest rate to
+ * send management frames and NO_ACK data with the respective hw
+ * retries should use this in the beginning of their mac80211 get_rate
+ * callback. If true is returned the rate control can simply return.
+ * If false is returned we guarantee that sta and sta and priv_sta is
+ * not null.
+ *
+ * Rate control algorithms wishing to do more intelligent selection of
+ * rate for multicast/broadcast frames may choose to not use this.
+ *
+ * @sta: &struct ieee80211_sta pointer to the target destination. Note
+ * 	that this may be null.
+ * @priv_sta: private rate control structure. This may be null.
+ * @txrc: rate control information we sholud populate for mac80211.
+ */
+bool rate_control_send_low(struct ieee80211_sta *sta,
+			   void *priv_sta,
+			   struct ieee80211_tx_rate_control *txrc);
+
+
+static inline s8
+rate_lowest_index(struct ieee80211_supported_band *sband,
+		  struct ieee80211_sta *sta)
+{
+	int i;
+
+	for (i = 0; i < sband->n_bitrates; i++)
+		if (rate_supported(sta, sband->band, i))
+			return i;
+
+	/* warn when we cannot find a rate. */
+	WARN_ON_ONCE(1);
+
+	/* and return 0 (the lowest index) */
+	return 0;
+}
+
+static inline
+bool rate_usable_index_exists(struct ieee80211_supported_band *sband,
+			      struct ieee80211_sta *sta)
+{
+	unsigned int i;
+
+	for (i = 0; i < sband->n_bitrates; i++)
+		if (rate_supported(sta, sband->band, i))
+			return true;
+	return false;
+}
+
+int ieee80211_rate_control_register(struct rate_control_ops *ops);
+void ieee80211_rate_control_unregister(struct rate_control_ops *ops);
+
+static inline bool
+conf_is_ht20(struct ieee80211_conf *conf)
+{
+	return conf->channel_type == NL80211_CHAN_HT20;
+}
+
+static inline bool
+conf_is_ht40_minus(struct ieee80211_conf *conf)
+{
+	return conf->channel_type == NL80211_CHAN_HT40MINUS;
+}
+
+static inline bool
+conf_is_ht40_plus(struct ieee80211_conf *conf)
+{
+	return conf->channel_type == NL80211_CHAN_HT40PLUS;
+}
+
+static inline bool
+conf_is_ht40(struct ieee80211_conf *conf)
+{
+	return conf_is_ht40_minus(conf) || conf_is_ht40_plus(conf);
+}
+
+static inline bool
+conf_is_ht(struct ieee80211_conf *conf)
+{
+	return conf->channel_type != NL80211_CHAN_NO_HT;
+}
+
+static inline enum nl80211_iftype
+ieee80211_iftype_p2p(enum nl80211_iftype type, bool p2p)
+{
+	if (p2p) {
+		switch (type) {
+		case NL80211_IFTYPE_STATION:
+			return NL80211_IFTYPE_P2P_CLIENT;
+		case NL80211_IFTYPE_AP:
+			return NL80211_IFTYPE_P2P_GO;
+		default:
+			break;
+		}
+	}
+	return type;
+}
+
+static inline enum nl80211_iftype
+ieee80211_vif_type_p2p(struct ieee80211_vif *vif)
+{
+	return ieee80211_iftype_p2p(vif->type, vif->p2p);
+}
+
+void ieee80211_enable_rssi_reports(struct ieee80211_vif *vif,
+				   int rssi_min_thold,
+				   int rssi_max_thold);
+
+void ieee80211_disable_rssi_reports(struct ieee80211_vif *vif);
+
+int ieee80211_add_srates_ie(struct ieee80211_vif *vif, struct sk_buff *skb);
+
+int ieee80211_add_ext_srates_ie(struct ieee80211_vif *vif,
+				struct sk_buff *skb);
+#endif /* MAC80211_H */