\section{Controlling servomotor through Scilab} \subsection{Controlling the servomotor} \label{sec:servo-sci} In this section, we discuss how to carry out the experiments of the previous section from Scilab. We will list the same four experiments, in the same order. The Shield has to be attached to the \arduino\ board before doing these experiments and the \arduino\ needs to be connected to the computer with a USB cable, as shown in \figref{arduino}. The reader should go through the instructions given in \secref{sec:sci-start} before getting started. % In this section, we will carry out the servomotor control experiments % using \scilab. We will follow the same order as in % \secref{sec:servo-ard}. We assume that the shield is attached to the % \arduino\ board while doing these experiments. They will work without % the shield also, but in this case, our comments on colour LEDs % lighting will not be applicable. The reader should go through the % instructions given in \secref{sec:sci-start} before getting started. \begin{enumerate} \item The first experiment makes the servomotor move by $30^\circ$. The code for this experiment is given in \sciref{sci:servo-init}. As explained earlier in \secref{sec:light-sci}, we begin with serial port initialization. % It first opens com port 2 in \arduino\ card number 1 with baud rate % of 115200. If the port opening is unsuccessful {\tt ok} will not be % 0 and the program terminates, asking the user to correct the % problem. Else If the port opening is successful, {\tt ok} will be 0 % and the program proceeds. Next, we attach the servomotor by issuing the command given below: \lstinputlisting[firstline=3,lastline=3]{\LocSERscicode/servo-init.sce} As shown above, the servomotor is attached on board 1 (the first argument) to pin 1 (the second argument). In Scilab-Arduino toolbox discussed in \secref{sec:sci-ard-toolbox}, pin 1 and pin 5 are connected. As a result, we connect the wire physically to pin 5, which is achieved by the Shield as discussed in \secref{sec:servo-pril}. With this, we issue the command to move the servomotor by $30^\circ$ followed by a delay of 1000 milliseconds: \lstinputlisting[firstline=4,lastline=5] {\LocSERscicode/servo-init.sce} At last, we detach the servomotor followed by closing the serial port. Once this code is executed, the servomotor would move by $30^\circ$, as commanded. What happens if this code is executed once again? The motor will not move at all. What is the reason? Recall that what we assign to the motor are absolute positions, with respect to a fixed origin. As a result, there will be no change at all. \item In the second experiment, we move the servomotor by $90^\circ$ in the forward direction and $45^\circ$ in the reverse direction. This code is given in \sciref{sci:servo-reverse}. In this code, we have added a delay of 1000 milliseconds between the two instances of moving the servomotor: \lstinputlisting[firstline=4,lastline=6] {\LocSERscicode/servo-reverse.sce} What is the reason behind this delay? If the delay were not there, the motor will move only by the net angle of $90-45 = 45$ degrees. The reader should verify this by commenting on the delay command. % In \sciref{sci:servo-reverse}, we make the servomotor rotate % to $90^\circ$, wait for a second and go to $45^\circ$. As mentioned % earlier, the angles are absolute with respect to a fixed reference % point and not relative. \item In the third experiment, we move the motor in increments of $20^\circ$. This is achieved by the {\tt for} loop, as in \sciref{sci:servo-loop}. The code helps the motor move in steps of $20^\circ$ all the way to $180^\circ$. \item Finally, in the last experiment, we read the potentiometer value from the Shield and use it to drive the servomotor, see \sciref{sci:servo-pot}. The resistance of the potentiometer is represented in 10 bits. As a result, the resistance value could be any one of 1024 values, from 0 to 1023. This entire range is mapped to $180^\circ$, as shown below: \lstinputlisting[firstline=5,lastline=7] {\LocSERscicode/servo-pot.sce} By rotating the potentiometer, one can make the motor move by different amounts. As mentioned in \chapref{potmeter}, the potentiometer on the Shield is connected to analog pin 2 on \arduino. Through this pin, the resistance of the potentiometer, in the range of 0 to 1023, depending on its position, is read. Thus, by rotating the potentiometer, we make different values appear on pin 2. This value is used to move the servo. For example, if the resistance is half of the total, the servomotor will go to $90^\circ$ and so on. The servomotor stops for 500 milliseconds after every move. The loop is executed for 50 iterations. During this period, the servomotor keeps moving as dictated by the resistance of the potentiometer. While running this experiment, the readers must rotate the knob of the potentiometer by a fixed amount and observe the change in the position (or angle) of the servomotor. % \item In the next experiment, we rotate the servomotor in discrete % steps of $20^\circ$. This is achieved by multiplying $20^\circ$ by % an integer {\tt i}, which varies from 0 to 10. Once the maximum % angle reaches $180^\circ$, it stops. % \item Finally, in the last experiment, we position the servomotor % through the potentiometer in the code \sciref{sci:servo-pot}. As we % rotate the potentiometer, the servomotor's angle also changes. The % potentiometer value is read through pin 2, in line number 5, as % below: % \lstinputlisting[firstline=5,lastline=5]{\LocSERscicode/servo-pot.sce} % This value is mapped into a value between 0 and $180^\circ$ by % multiplying with $180/1023$ in line 6: % \lstinputlisting[firstline=6,lastline=6]{\LocSERscicode/servo-pot.sce} % The {\tt floor} function gets the integer part of the number by % truncation. This is the angle by which the potentiometer is to be % moved. Truncation is a not a crucial calculation, however. In % every iteration, the servomotor's position is calculated, and placed % for half a second. This loop is iterated upon 5,000 times. \end{enumerate} \subsection{Scilab Code} \lstset{style=mystyle} \label{sec:servo-scilab-code} \addtocontents{cod}{\protect\addvspace{\codclr}} \begin{scicode} \ccaption{Rotating the servomotor to a specified degree} {Rotating the servomotor to a specified degree. Available at \LocSERscibrief{servo-init.sce}.} \label{sci:servo-init} \lstinputlisting{\LocSERscicode/servo-init.sce} \end{scicode} \begin{scicode} \ccaption{Rotating the servomotor to a specified degree and reversing} {Rotating the servomotor to a specified degree and reversing. Available at \LocSERscibrief{servo-reverse.sce}.} \label{sci:servo-reverse} \lstinputlisting{\LocSERscicode/servo-reverse.sce} \end{scicode} \begin{scicode} \ccaption{Rotating the servomotor in steps of $20^\circ$}{Rotating the servomotor in steps of $20^\circ$. Available at \LocSERscibrief{servo-loop.sce}.} \label{sci:servo-loop} \lstinputlisting{\LocSERscicode/servo-loop.sce} \end{scicode} \begin{scicode} \ccaption{Rotating the servomotor to a degree specified by the potentiometer} {Rotating the servomotor to a degree specified by the potentiometer. Available at \LocSERscibrief{servo-pot.sce}.} \label{sci:servo-pot} \lstinputlisting{\LocSERscicode/servo-pot.sce} \end{scicode} \section{Controling servomotor through Xcos} \label{sec:servo-xcos} In this section, we will see how to rotate the servomotor from Scilab Xcos. We will carry out experiments similar to the ones in earlier sections. For each, we will give the location of the zcos file and the parameters to set. The reader should go through the instructions given in \secref{sec:xcos-start} before getting started. \begin{enumerate} \item First we will rotate the servomotor by $30^\circ$. When the file required for this experiment is invoked, one gets the GUI as in \figref{fig:servo-init}. In the caption of this figure, one can see where to locate the file. \begin{figure} \centering \includegraphics[width=\smfig]{\LocSERfig/servo-init.png} \caption[Rotating the servomotor by a fixed angle]{Rotating the servomotor by a fixed angle. This is what one sees when \LocLEDscibrief{servo-init.zcos}, is invoked.} \label{fig:servo-init} \end{figure} We will next explain how to set the parameters for this simulation. To set value on any block, one needs to right click and open the {\tt Block Parameters} or double click. The values for each block is tabulated in \tabref{tab:servo-init}. All other parameters are to be left unchanged. \begin{table} \centering \caption{Parameters to rotate the servomotor by $30^\circ$} \label{tab:servo-init} \begin{tabular}{lp{2.5cm}p{2.5cm}} \hline Name of the block & Parameter name & Value \\ \hline ARDUINO\_SETUP & Identifier of Arduino Card & 1 \\ & Serial com port number & 2\portcmd \\ \hline TIME\_SAMPLE & Duration of acquisition(s) & 10 \\ & Sampling period(s) & 0.1 \\ \hline SERVO\_WRITE\_SB & Servo number & 1 \\ & Arduino card number & 1 \\ \hline CONST\_m & Constant value & 30 \\ \hline \end{tabular} \end{table} \item Next, we will rotate the servomotor by $90^\circ$ and bring it to $45^\circ$, all absolute values. When the file required for this experiment is invoked, one gets the GUI as in \figref{fig:servo-reverse}. In the caption of this figure, one can see where to locate the file. \begin{figure} \centering \includegraphics[width=\smfig]{\LocSERfig/servo-reverse.png} \caption[Rotating the servomotor forward and then reverse]{Rotating the servomotor forward and then reverse. This is what one sees when \LocLEDscibrief{servo-reverse.zcos}, is invoked.} \label{fig:servo-reverse} \end{figure} We will next explain how to set the parameters for this simulation. To set value on any block, one needs to right click and open the {\tt Block Parameters} or double click. The values for each block is tabulated in \tabref{tab:servo-reverse}. All other parameters are to be left unchanged. \begin{table} \centering \caption{Parameters to rotate the servomotor forward and reverse} \label{tab:servo-reverse} \begin{tabular}{lp{2.5cm}p{2.5cm}} \hline Name of the block & Parameter name & Value \\ \hline ARDUINO\_SETUP & Identifier of Arduino Card & 1 \\ & Serial com port number & 2\portcmd \\ \hline TIME\_SAMPLE & Duration of acquisition(s) & 10 \\ & Sampling period(s) & 0.1 \\ \hline SERVO\_WRITE\_SB & Servo number & 1 \\ & Arduino card number & 1 \\ \hline STEP\_FUNCTION & Step time & 1 \\ & Initial value & 90 \\ & Final value & 45 \\ \hline \end{tabular} \end{table} \item Next, we will rotate the servomotor in increments of $20^\circ$. When the file required for this experiment is invoked, one gets the GUI as in \figref{fig:servo-loop}. In the caption of this figure, one can see where to locate the file. \begin{figure} \centering \includegraphics[width=\smfig]{\LocSERfig/servo-loop.png} \caption[Rotating the servomotor in increments of $20^\circ$] {Rotating the servomotor in increments of $20^\circ$. This is what one sees when \LocLEDscibrief{servo-loop.zcos}, is invoked.} \label{fig:servo-loop} \end{figure} We will next explain how to set the parameters for this simulation. To set value on any block, one needs to right click and open the {\tt Block Parameters} or double click. The values for each block is tabulated in \tabref{tab:servo-loop}. {\tt Do on Overflow 0} means that we need to do nothing when there is an overflow. All other parameters are to be left unchanged. \begin{table} \centering \caption{Parameters to make the servomotor to sweep the entire range in increments} \label{tab:servo-loop} \begin{tabular}{lp{2.5cm}p{2.5cm}} \hline Name of the block & Parameter name & Value \\ \hline ARDUINO\_SETUP & Identifier of Arduino Card & 1 \\ & Serial com port number & 2\portcmd \\ \hline TIME\_SAMPLE & Duration of acquisition(s) & 10 \\ & Sampling period(s) & 0.1 \\ \hline SERVO\_WRITE\_SB & Servo number & 1 \\ \hline CLOCK\_c & Period & 1 \\ & Initialization time & 0.1 \\ \hline Counter & Minimum value & 0 \\ & Maximum value & 10 \\ & Rule & 1 \\ \hline GAINBLK & Gain & 20 \\ & Do on overflow & 0 \\ \hline \end{tabular} \end{table} \item Finally, we will use Xcos to rotate the servomotor as per the input received from the potentiometer. When the file required for this experiment is invoked, one gets the GUI as in \figref{fig:servo-pot}. In the caption of this figure, one can see where to locate the file. \begin{figure} \centering \includegraphics[width=\smfig]{\LocSERfig/servo-pot.png} \caption[Rotating the servomotor as suggested by the potentiometer]{Rotating the servomotor as suggested by the potentiometer. This is what one sees when \LocLEDscibrief{servo-pot.zcos}, is invoked.} \label{fig:servo-pot} \end{figure} We will next explain how to set the parameters for this simulation. To set value on any block, one needs to right click and open the {\tt Block Parameters} or double click. The values for each block is tabulated in \tabref{tab:servo-pot}. All other parameters are to be left unchanged. The {\tt ANALOG\_READ\_SB} block reads the value of potentiometer. Next, {\tt GAIN\_f} is used to convert the potentiometer values into rotation angle by multiplying the values with $180/1023$. \begin{table} \centering \caption{Parameters to rotate the servomotor based on the input from the potentiometer} \label{tab:servo-pot} \begin{tabular}{lp{2.5cm}p{2.5cm}} \hline Name of the block & Parameter name & Value \\ \hline ARDUINO\_SETUP & Identifier of Arduino Card & 1 \\ & Serial com port number & 2\portcmd \\ \hline TIME\_SAMPLE & The duration of acquisition(s) & 100 \\ & Sampling period(s) & 0.1 \\ \hline SERVO\_WRITE\_SB & Servo number & 1 \\ \hline ANALOG\_READ\_SB & Analog Pin & 2 \\ & Arduino card number & 1 \\ \hline GAIN\_f & Gain & 180/1023 \\ \hline \end{tabular} \end{table} \end{enumerate}